Construction of Tubewell in alluvium area at:.Shri Bhareshwar Gaushala, Vill.:Golap Nesda, Sr. no./ Block No.:433, Ta:.Suigam, Dist.:Vav-Tharad along with S.I.T.C. work of pumping machineries with necessary accessories in Special Case under PINS Tubewell for the Year 2025-26. (2nd Attempt)

Name of work : Construction of Tubewell in alluvium area at:Shri Bhareshwar Gaushala, Vill.:Golap-

Nesda, Sr. no./ Block No.:433, Ta:.Suigam, Dist.:Vav-Tharad along with S.I.T.C. work of pumping

machineries with necessary accessories in Special Case under PINS Tubewell for the Year 2025-

26.(2nd Attempt)

Item Item Unit Qty Unit Rate Amount Rs.

(A) Drilling of pilot hole & reaming by mud-flush rotary

equipment in alluvium & Unconsolidated formations

and stone to be provided by contractor Bore shall

stand uncased for at least 72 hours (500 mm Dia

1 0.00 to 60.00 mtr mtr 60

6 Electrologging Job 1

7 Providing of 273 mm O.D. M.S plain pipe having mtr 241

7.1 mm thickness.

8 Providing of 273 mm O.D. M.S (1/8’’) & (1/16’’) mtr 60

slotted pipe ( with A.G.L per tw ) having 7.1 mm

9 MS pipe support suitable for 273 mm dia O.D pipe Nos 156

Size 200x125x8 mm thick

10 MS cupling suitable for 273 mm dia O.D pipe size Nos 1

11 MS wellcap suitable for 273mm dia. O.D. pipe size Nos 1

200x7.1 mm thick pipe and 3 mm thick top plate.

12 MS clamp suitable for 273mm dia. O.D. pipe size Pair 1

© Lowering of pipe Assembly of 250 mm Dia pipe as

recommended by Geo wing

18 Supply of Gravel (3-5 mm for 1.5 mm slot) (2-4mm Cmt 23

for 1 mm slot) as per as recommended by Geo

19 Gravel packing labour (3-5 mm for 1.5 mm slot) Cmt 23

(2-4mm for 1 mm slot) as per as recommended by

Cement Sealing Job 1

21 Clay balls and Packing Cmt 22

22 Development by Air compressor the development hrs 10

of bore by air compressor should be done in such a

way that each water bearing zones are developed

in descending order separately by compressed air.

23 Pump Test: the bore should be properly developed hrs 15

and tested by require capacity of sub test unit

24 Providing, lowering & testing of three phase sub. pump

coupled with motor suitable for 250mm dia & all

required accessories like strainer, NRV, 5mtr lead cable

of suitable size of approved make with miscellaneous

hardware materials etc Complete.Three phase

Submersible Pump set coupled with motor & with all

required accessories like strainer, NRV, 5 mtrs. lead

cable of suitable size of approved make etc.

1100 to 1200 LPM x 50 to 70 Mtr. (25 to 30 HP)

Approximate rate for 31 to 35 HP , per HP if Higher

required Per HP 5 2295.05

25 Providing of Flat p.v.c Cable size 1 x3x 10 sq mm

CABLE: Three core Flat P.V.C. insulated water Proof &

flexible copper cable used for the Sub-motor pump &

power wiring shall confirming to IS: 694 of required

size of approved make. The cable should be bind with

column pipe while lowering in tubewell

The cable should be bind with column pipe while

lowering in tubewell.

26 Providing of M.S Column pipe Black ERW/HFIW

pipes of ‘C’ class in three meters length &

threaded at both ends in the length of 45 mm /

mm. of 11 T.P.I / 8 T.P.I. having suitable size of Nos. 22 3380.93

coupling (as per specification.) at one end & socket

(rubber protector) at other end.

size: Column pipe 100 mm dia (4"dia) 3mtr length

27 Providing of Control Panel board

A.C. Three Phase (A.T.S. type) complete with

meters and Capacitor suitable to motor HP with

GEB testing Certificate. Acceptance make: As

stated in tender.

Providing of Hot forged M.S. Clamps

manufactured from M.S. flat confirming to IS: 226 &

fitted With ¾” dia 3” long high tensile strength bolts

28 , Nuts & Washers. (2sets on each sides). Overall Pair 2 1112.72

length for clamps should be 24” suitable for column

size 100mm dia x 100mm Width x16mm thick

Providing of C.I.Flange size 4" dia C.I. Flange

29 having 8 TPI threaded & 16m.m. thickness. No. 2 235.38

Providing of short bend 100 mm - C.I. flange short

bend suitable having flange thickness 16mm &

30 angle of bend 90 degree. Nos. of holes 04 nos. No. 1 787.46

suitable for 100mm dia pipe.

Providing of M.C.T.P./SMTP Main Switches of

AMP HRC type Fuses suitable for 415V acceptable

31 makes as per category-II & III approved by No. 1 5812.55

Electrical Division, Govt. of Gujarat, R&B

ELCBs conforming to IS: 12640 and having

sensitivity of 30 mA and short circuit with stand

capacity of 6 KA and suitable for operation on

phase and neutral 415V having characteristic of

32 quick action & tripping with all advance feature & No. 1 3656.54

do not incorporate any electronic component for

following Max rating erected as directed

(1) 100 Amp FP (100mA sensitivity) cat-III

Providing dust and vermin proof MS cabin having

two compartments, one for panel board and other

for energy meter and fuse unit with required locking

arrangement , minimum degree of protection IP

as per IS 2147 fabricated from CRCA sheer steel

minimum thickness for base frame / channel / gland

plates for 3 mm for load bearing members,1.6 mm

for ineternal members including cutting, bending,

drilling, welding, riveting with ineternal

partitions.The sheet steel enclosure shall be

powder coated as per applicable standard with

shade as required with finish thickness of paint film

not less than 80 microns.The cabin shall have

following dimension 1.5 M X 1.25 M x 0.6 M

TOTAL AMOUNT RS.

TOTAL AMOUNT RS.