Providing water supply scheme to Palgi Dhallan, Muhan, Garsa, Railla, Rote Bhallan, Dhara, Tarala, Rohana-Donal, Kashadi, Dhari, Phatiana, Kothi-Chehani, Khadagad, Seri, balagad, Tandi, Chethar, Pekhari, Sarchi, Laida, Tilroo, Thatibir, Phatti Ratwa

Amount

Cutting in earth work and disposal of excavated earth up to lead of 20 mtrs. in all kinds of soil in pick work, jumper work and blasting work complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Excavation in foundations, trenches etc., in earth work , lift up to 1.50 metres stacking the excavated soil not more then 3 metres clear from the edge of excavation and then returning the stacked soil in 15 cm layers, when required in to plinths , sides of foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed within a lead of 20 metres in pick jumper work complete in all respects with in all leads and lifts as per direction of Engineer in charge.

Providing and laying cement concrete 1:6:12 ( 1 cement,6 sand,12 graded stone aggregate 40 mm nominal size )and curing complete excluding cost of form work in foundation and plinth with in all leads and lifts complete in all respect.

P/L CC 1:4:8 (1 cement:4 sand:8 graded stone agg.40mm nominal size) and curing complete excluding the cost of form work in foundation and plinth including all leads, lifts and carriage of material at site and to the entire satisfaction of Engineer Incharge.

Random rubble masonry/polygonal rubble masonry ( uncoursed/ brought to courses) with hard of approved quality in foundation and plinth including levelling up with CC 1:6:12 (1cement:6sand:12 graded stone aggregate 20mm nominal size) at plinth level in:-cement mortar 1:6 (1 cement : 6 sand) including all leads, lifts and carriage of material at site and to the entire satisfaction of Engineer Incharge.

Stone soling properly hand packed filling interstices with spallsand consolidating with hammer to the required gradient & slope i/c spreading,watering & rolling of binding Material,moorum or earth etc. 100mm spread thickness(finished work i/c Material & labour.

Stone filling behind the Retaining wall with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Brick work using common burnt clay building bricks I) in foundation & plinth in cement mortor 1:6 (1 cement: 6 sand), Ist class bricks with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

In super structure above plinth level up to floor two level in cement mortor 1:6 (1 cement: 6 sand), Ist class bricks with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Prov. Form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring , shuttering, strutting & propping etc. with wooden battens & ballies , height of propping & centring below supporting floor to ceiling not exceeding 4 mtrs.& removal of the same for insitu reinforced concrete & plain concrete work in : - Vertical surfaces such as walls (any thickness) partitions & the like I/c attached pillasters, buttresses plinth and string courses and the like :

Flat surfaces such as soffits of suspended floors roofs landings and the like floors etc upto 200mm in thickness with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and laying CC 1:1.5:3 (1 cement:1.5 sand:3 graded stone agg.20mm nominal size) and curing complete exlcuidntg the cost of form work and reinforcement in:-

Foundation and plinth with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Walls(any thickness but ot less than 0.1 mtr thickness) attached pilasters, buttresses, plinth and string courses etc. from top of foundation level up to floor two level with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Suspended floors, roofs, landings and shelves and their suport balconies, beams,girders bressumers and cantilivers upto floor two level with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and laying CC 1:2:4 (1 cement:2 sand:4 graded stone agg.20mm nominal size) and curing complete exlcuidntg the cost of form work and reinforcement in:-

Suspended floors, roofs, landings and shelves and their suport balconies, beams,girders bressumers and cantilivers upto floor two level with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all lea

Providing and laying RCC 1:2:4 Vertical and horizontal (thickness not more than 0.10 m) individually or forming box louvers and projected and upto floor two level with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and laying cement concrete 1:5:10 (1cement:5 sand:10graded stone agg. 40 mm nominal size) with 15% plums and curing complete excluding cost of form work in foundation and plinth with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing tor steel reinforcement for RCC work including bending, binding and placing in position complete upto floor two level with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing wood work in frames of doors,windows,clerestory windows and other frames wrought framed and fixed in position. IInd class Deodar wood with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing panelled glazed or panelled and glazed shutters for doors, windows and clerestory windows, including black enamelled iron butt hinges with necessary screws 40 mm thick 2nd class deodar wood with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

P/F wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85G with wire of dia 0.56mm for doors, windows & clerestory windows including bright finished black enamelled iron hinges with necessary screws 40 mm thick 2nd class deodar wood

Providing and fixing 1.80 m high barbed wire fencing with angle iron posts 2.50 high 40x40x4 2.50m C/C with 9 horizontal rows and 2 diagonal rows of barbed wire embedded om c.c. 1:4:8 (1 cement:4 sand:8 graded stone agg.40mm nominal size) with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing steel gate around Intake and storage tank complete in all respects with in all leads and lifts as per direction of Engineer in charge.

6mm cement plaster to ceiling in CM 1:3(1 cement:3 sand) with in all leads and lifts to the entire satisfaction of the Engineer-in-charge.

15mm cement plaster in single coat on rough side of brick/concrete stone walls for interior plastering upto floor two levels inclduing arrises internal rounded angles, chamfers end/or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortor 1:6 (1 cement: 6 sand) with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

cement concrete flooring 1:2:4(1 cement: 2 sand: 4graded stone agg. 20mm nominal size) laid in one layer finished with a floating of neat cement 40mm thick with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

White wasing with lime on decorated wall surfaces two coats to give an even shade including thoroughly brooming the surface to remove all dirt, dust and other foreign matters with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Applying priming coat on new wood and wood based surfaces after and incluidng papering the surface by thoroughly cleaning oil, grease, dirt and other foreign matters, sand papering and knotting, readymixed paint brushing wood primer pink with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with enamel paint to give an even shade incluidng cleaning the surface of dirt, dust and other foreign matters sand papering and stoping with enamel paint other than white with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick/stone aggregate 40mm nominal size well rammed and consolidated and grouted with fine sand including preperation of ground with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing plinth protection 50mm thick in cement concrete 1:3:6(1cement:3sand:6graded stone agg 20mm nominal size) with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing MS sliding door bolts anodised colour and shade with nuts and screws complete in all respect. I) 250X16mm

Providing and fixing MS tower bolts ( Barrel type ) anodised transparent or died to required shade with necessary screws complete in all respect. I) 200X10 mm

Providing and fixing MS handles anodised,transparent or died to required shade with necessary screws complete in all respect. I) 125 mm

Sanitary work: Providing and fixing to wall ceiling and floor galvanised mild steel tubes (MG) including fitting and clamps including making good the wall ceiling and floor complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge ..

a) 15mm nominal size

Providing and placing (at all heights) polyethylene water storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes including all fittings and float valve excluding the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid ISI license with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts. ]. 300 Ltrs. capacity

Providing and fixing vitreous china wash, down water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1 (1 cement: 1 sand). Seat and cover to be measured and paid for seperately. Anglo Indian Universal closet.

Providing and fixing plastic seat and cover for wash down water closet with C.P. brass hinges and rubber buffers: White plastic seat and cover, solid type with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing & fixing 10 litre vitreous china low level flushings Cistern with a pair of CS brackets complete with fittings such as lead valveless syphon 15 mm nominal size brass valve with polythene float, CP brass handle, unions & coupling with connection with in inlet- outlet & over flow pipe 40 mm side CP slush bend, including cutting holes in walls closet ( overflow pipe to be measured & paid seperately ) etc. complete in all respect. A) Vitrous China in white colour with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing PVC / G.I. inlet connection for flush pipe connecting with W.C. pan with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing C.P. brass angle valve of standard design and of approved make, 15mm nominal bore in complete in all respects with in all leads and lifts as per direction of Engineer in charge.

Providing and fixing C.P. water jet including connection pipe with check nut complete in all respect

Providing and fixing PVC pipes of 10 Kg f/Sq.cm working pressure including fittings as per requirement at site complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge. 110 mm OD

Electrical work:- Wiring for light point / fan point / exhaust fan / call bell pointwith 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. Group-B

Wiring for Circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required.

2x1.5 sqmm.

2x4 sqmm.

Supplying and fixing following rating Piano-type switch /socket on the existing switch box / cover including connections etc. as required with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

S.P. 5/ 6 Amps one way switch, piano type.

5 pin 5/ 6 Amps socket outlet, porcelain base/ piano type.

Supplying and fixing following rating Piano-type switch /socket on the existing switch box / cover including connections etc. as required with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all lea

S.P. 15/16 Amps one way switch, porcelain base/ piano type.

6 pin 15/16 Amps socket outlet, porcelain base/ piano type.

Supplying & fixing wooden box of following sizes (nominal size) on surface or in recess suitable for fixing phenolic laminated sheet cover in front including painting etc. as required with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

180mm.x100mm.x60mm. Deep

250mm.x200mm.x60mm. Deep

Providing and installing testing and commissioning of prewired fluorescent tube fitting, complete with ballast, starter and capacitors but excluding fluorescent tube rod, suitable to operate on 230 volts, single phase AC supply directly on surface with copper wiring as required. F/Tube 1X40 watt,including all leads, lifts and carriage of materials and as directed by the Engineer Incharge.-Group C Box type category A.

Providing and fixing florescent tube rod 4 feet long in the existing tube fittings as required as per specification on the caragory with in all laeds, lifts and to the entire satisfaction of engineer incharge.

Supplying and fixing ceiling rose on the existing junction box / wooden block including connections etc. as required with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing batten holder on existing wiring including connection complete in all respect as required with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wireset, neutral link, earth bar, din-bar, detachable gland plate blanking plate, cable, identification labels interconnections,phosphatized and powder painted, including earthing etc. as required with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Single door-12 way

Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature CSrcuit breaker of following poles in the existing MCB DB complete with connections etc. as required with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Single pole. Cat-A.

Earthing with G.I earth pipe 4.5 mtr. long and 40mm dia,including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Extra for using salt and coke for pipe earth electrode complete as required with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

63 Amps. Cat-A.

Supplying and fixing LED bulb of 9 watt including testing and commissioning complete in all respect as required with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. as required with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Ceiling Fan 1200 mm sweep, Category-A

Laying in trenches galvanised mild tube(light grade) with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

20 mm dia

25 mm dia

40 mm dia

Laying, jointing, of GI pipes for inlet ,outlet,scour pipe and bypass arrangement complete in all respect.) 50 mm dia with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts. (L.R)

Providingand fixing GMS tubes of following dia in walls, floors etc i/c tube fitting and making the wall flour etc good) 32 mm dia with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing of brass wheel valves with hand wheel complete in all respect) 32 mm dia with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Prov .and fixing Gun Metal Wheel valve (with hand wheel) 50 mm diameter for inlet, outlet and scour with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Prov. & fixing SFRC manhole cover for frame of internal size 560 mm dia with frame (medium duty)within all leads and lifts(weight of cover & frame not less then 100 kg)

Providing and placing in horizontal layers filtering media duly graded, screened,cleaned and washed as specified with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Top layer, Fine sand( Eff. Size 0.20mm to 0.40 and uniformity co-efficient 2.00 to 3.00).

Second layer, Coarse sand, 3mm - 6mm

Third layer : Bajri 6mm to 20 mm.

Fourth layer : Bajri 20mm to 25 mm

Bottom layer : Broken stone 50mm to 75 mm.

Providing & placing Precast Concrete Block in CC 1:2:4 of size 0.30 x 0.40 x 0.05 ( I cement :2 sand ;4 graded stone aggrigate 20 mm nominal size)over X Drain with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and lying in trenches 3 layer PPR pipes (poly propylene random copolymer)earth work in trenches to be measured and paid for seperately with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Laying, jointing of GMS tube in trenches of following meter including providing and fixing tube fitting such as bends, tees, air valves, unions and collars etc. including carraige of GI pipes as per direction and to the entire satisfaction of the Engineer-in-charge (earth work in trenches to be measured and paid for separately) with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing & installation of House connection with Union,Ferrule,elbow,coulings complete in all respect and to the entire satisfaction of Engineer in charge with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Laying, jointing (by way of Circumfrential but welded joints by electrical arc welding) and testing of Galvanised mild steel tubes (GI Pipes) of following diameters confirming to ISO:1239-2001, (latest with uptodate amendments) having wall thickness as per code with bevelled/plain ends and capable of withstanding required test pressure in a random length of 4 to 7 meters including manufacturing reducers/tapers, all short pieces, bends etc as per site requirement made from parent tube. The laying of pipe will include all operations such as cutting, welding, jointing, fabrication of bends, tees etc including lowering and laying in excavated trenches to ensure required level including flushing, cleaning and hydraulic testing complete in all respects to the satisfaction of the Engineer in charge. The fabricated bends shall have three of four cuts having it's radius not less than five times the dia of pipe. The pipes shall be factory galvanised ( zinc coating both inside and outside) as per relevant IS standards and the damaged portion of the pipes and specials made from the parent tube during welding or otherwise shall be provided anticorrosive treatment by applying two coats of anticorrosive bituminous paint over a priming coat as per AWWA speCSfications C-203-1978. The wleding electrodes shall be as per IS: 814 of Advani Oerlikon/ L&T or ISI marked make. the rates also includes entire carriage of material, flushing, cleaning & hydraulic testing complete to the best satisfaction & direction of Engineer-in-charge within all leads and lifts ( Earth work in trenches will be measured and paid for separately)

Stage

RD 0 to 330 50mm dia GI pipe W.T. 4.50 (H) 100% Butt Welded

RD 330 to 970 50mm Dia GI pipe W.T 4.50 (H) 100 % Butt Welded

Stage-I Providing & fixing at site horizontal spindle,horizontal/redial split casing/end suction(Back-pull out arrangements) single/double/multi stage centrifugal pump or combination of pumps, In series/parallel of recommended make such as Mather and Platt/KSB/ Beacon Weir/Kirlosker/BE/Jyoti Grandfos and approved make as per BIS 1520-1980 with upto date ammendments, read with IS:9137-1978 or latest edition suitable for lifting water for under mentioned characterestics with bronze,impellers/priming funnels,casing ring and shaft sleeves of bronze,shaft of steel grade 4508 FN8 with cast iron casing coupled directly through a flexible coupling on a common MS/Cast steel base plate (base plate to be from the manufacturer of the pumping unit only) to slip ring/ squirrel cage screen protected drip proof induction motor /motors of standard make such as Kirlosker/BHEL /Crompton /NGEF /GEC/Siemens/Jyoti /ABB and suitable for operation on 400(+/-)10% volts,50 cycles /second.3 phase AC electric supply. The power of electric motor/motors should be at +10% in excess of the maximum power required by the pump/pumps in the operation range of (+) 10% and (-)15% of the duty poiint head. The motor/motors as per ISI:325:1978 with upto date ammendments read with IS 900:1972. It should include cost of bearing nuts , bolts and painting etc. and should meet the following requirements:

a) Discharge = 1.17LPS

b) Total head = 341.06 mtr.

C)LWL in Sump well= 992 mtr

D) Shaft level = 990.60 mtr

e) level at dischargr point = 1311.00 mtr

f) length of Rising main)= 970 mtr.

g) Dia of Rising main - 50 mm

Providing and fixing change over / ICTP main switch of Kilburn/ L&T/Siemens/Standard/ Havells & all approved make and having capacity 30% extra of the operational rating as per IS: 4064-1978 with up to date amendments , immediately after the power meter of the HPSEBL with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing MS sheet steel fabricated floor mounted closed(almirah type) switch board including angle iron post of suitable height and size ISA 40x4r0x6 duly painted with steel sheet of 16 gauge comprising and capable of mounting the following accessories within all internal connections. All the accessories should be suitable for the proposed pumping machinery at item No.54 above and to the entire satisfaction of HPSEB authorities. The same shall have to be replaced with out extra cost if recommended by HPSEB authorities with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

a) Providing and fixing OCB/MCCB of MEI/Havels/ standard & all approved make and of suitable capacity for offered motor on incoming feeder with or without initial oil filling as the case may be with neutral linked under voltage released as per relevent IS code with upto date ammendments with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

b) Providing and fixing Earth leakage Circuit breaker of recommended make (Kilburn/L&T/MEI/GEC) & all approved as per IS:2516:1977 with upto date ammendments of suitable range which should have control box, operation, handle and trip/reset bush button on/off indicators, re-indicating off spring condition of the Ciruit breaking for cover current protection. The Circuit should be equipped with magnet thermal release with metallic tap etc, it should also be fitted with earth fault for tripping of breaker on occurnce of earth fault on off breaker load side end with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

g) Providing and fixing Bus bar chamber having three copper bars of suitable rating for full length equal to the width of the board for three live phases and suitable for inducted current, one copper bar of half the rating of full length for neutral phase as per IS 8084-1976 and IS:11353-1985 read with BIS 5578-1985 with upto date ammendments with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

h) Providing and fixing ICTP switches with HRC fuses unit of Kilbur/L&T/siemens/stands/Havells & all approved make and of suitable capacity as per IS:4064:1978 with upto date ammendments with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

i) Providing and fixing Three phase indicator lamps complete with toggle switches for individual motors as per IS:3452:(P-I & II) with upto date ammendments with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

k) Providing and fixing Capacitor of Mechneil/ BHEL/GEC make as per 15:2834:1986 with upto date ammendments, to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rting according to H.P.offered including cables as per relevant ISI code (of siemens/clocter.IEC make )from bus bar chamber to capacitor and also including ICTP switches of appropriate range as per Is:4064:1978 with upto date ammendments with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

l) Providing and fixing suitable oil immersed starter delta/air break direct on line/auto transformer/. starter rotor starter of Havel/ MEI/.Kilburn/Jyoti /L&T/Siemens & all approved make as per IS:8544:1979 with upto date ammendments for squirrel cage/slip ring motor mounted on panel board with magnetic type over-load release and dashpot, time lag, under voltage release with or without initial oil filling as the case may be with single phae preventor as per IS:1248( P-V) 1983 with upto date ammendments with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

m) Providing and fixing Digital hour run meter of recommended make and suitable capacity as per IS:722 (latest edition.) with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing double flanged C.S sluice valve ASA-300 of Leader/BHEL/Kirlosker/GLEd/Kilburn Fourses / & all approved make equal to dia of Rising main and cpable of withstanding the normal seat pressure as per IS:780:1984 with upto date ammendments with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing double flanged cast steel sluice valves ASA-300 of leader/BHEL Kirlosker/Kilburn GLED/fourses & all approved make and one step higher then delivery size of pump and capable of withstanding the normal seat pressure and as per BIS standards with upto date ammendments

Providing and fixing double flanged cast steel reflux valves, ASA-300 of Leader/BHEL/ Kirlosker/Kilburn /GLEd/Fourses & all approved make and having bye pass arrangements of one step higher then delivery size of pump and capable of withstanding normal seat pressure as per BIS standards with upto date ammendments) with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing double flanged cast steel reflux valves class ASA-300 of Leader/ BHEL /KILROSKER /KILBURN/GLED/FOURSES & all approved make and equal size of rising main main and capable of withstanding normal seat pressure as per BIS standards with upto date ammendments with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing 100mm dia Circular analog pressure gauge of suitable range of Fiebig /Bourden/ PREGA /precision & all approved make complete with all accessories such as stop cock, copper tubing etc.as per IS: 3624-1987 with upto date ammendments with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Installation and errection of pump as per all items apparing at serial No.67 to 73 systematicaly as per drawing of as directed by the Engineer-in-charge.

Providing and fixing double flanged MS/GI piping work (Layout to be approved by the Engineer in charge) for suction and delivery pipes suitable to pump(s) offered and common header as per the R/Main respectively complete with all specials such as bends, tees, reducers. Increasers with companions flanges matching with the relevant specifications of the accessories including rubber/asbestos gasket of minimum 3mm thckness as per IS:2712:1979 and required number of nuts and bolts as per Is:1364:1983, The Pipes fittings and joints shall be as per relevant IS code & to withstand 1.5 times total head stipulated under item No.1. The size of the various components to be as under:

Suction pipe : One dia higher then the suction size of pump offered and suitable to keep the velocity of flow from 1 to 1.5M/second in the suction pipe

Delivery pipe: One dia higher then the delivery size of the pump offered and suitable to keep the velocity of flow from 1.5 to 2M/second in the delivery pipe

Common header : Equal to size of rising main and suitable to keep the velocity of flow from 1.5 to 2M/second in the delivery pipe

Providing and fixing and laying copper PVC insulated arsoured power cable (One cable carrying all the three phases) of suitable size and capacity to motors and all other electircal equipments as per IS:1554(P-I) 1988 or latest ith upto date ammendments of siemens/GLOSTER /IEC/ICC /EICO /NATIONAL /GRANDLAY & all approved make including all other accessories such as thinbles, flexible pipes,solders,nuts and bolts cable glands etc. laid in pipes or trenches under floor

(a) Motor side (From switch to starter and starter to motor)

(b) Supply side (From Meter of HPSEB to bus bar and switch)

Providing and fixing double loop earth with GI EARTH plate 600mmx600x3mm thick electrode complete with material such thimbles nuts and charcoal and common salt, 25mmx5mm copper strips as per IS:3043:1987 with upto date ammendments for motors and other electrical equipments and digging of pits etc. complete in all respect with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Yash Pal