PROVN OF TRAINING SHED WITH ANCILLARIES AT MIL STATION NAHAN UNDER GE CHANDIGARH

Amount

M&L for Surface dressing n exc 15 cm deep and getting out in in soft/loose soil complete all as specified.

M&L for Excavating in trenches(soft/loose soil) not exceeding 1.5 Metre wide and not exceeding 1.5 Metre in depth for laying of foundation, sewage/water lines etc not exceeding 10 Sqmtr on plan and getting out in any type of soil complete all as specified.

Removal of excavated soil to a distance exc 250 metre and n.exc 500m depositing where directed at a level not exc 1.5 metre above the starting point complete all as specified.

Returning and filling in including spreading leveling watering and well ramming in layers not exceeding 25 cm thick using soft/disintegrated rock all specified and as directed.

M&L for Hard core with broken stone or boulders of gauge not exceeding 63mm deposited, spread and levelled in layers not exc. 15 cm thick, watered and rammed/rolled to a true surface complete all as specified.

M&L for Plain cement concrete (1:4:8), type D-2, using 40 mm graded crushed stone aggregate as in foundations, filling , mass concrete and sub base, complete all as specified and directed.

M&L for Plain cement concrete (1:3:6), type C-2 using 40mm graded stone aggregate as in Plinth protection,75mm thick finished even and fair complete including necessary form work all as specified .

M&L for Forming contraction (dummy) joints 25 mm deep x 10mm wide, filled with sealing compound Grade A complete all as specified and as directed.

M&L for Earth filling under floors incl spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick complete all specified and as directed.

M&L for Plain cement concrete 100mm thick (1:4:8), type D-2, using 40 mm graded crushed stone aggregate as in sub base, complete, all as specified and directed.

M&L for Plain cement concrete 40mm thick (1:2:4), type B-1, using 20 mm graded crushed stone aggregate as in flooring, complete, all as specified and directed.

M&L Brick work with fly ash bricks straight or curved on plan exc 6m mean radius built in CM (1:4) complete all as specified and directed.

M&L for rendering 15mm thick plaster in CM (1:4) on brick/concrete surfaces incl roofs finishing the surface fair and evenwithout using extra cement and with liquid WPC as per manufacturer's instructions complete all as specified and directed. Note: WPC will be measured seprately.

Supply only liquid integral water proofing compound as per ISI mark all as specified and as directed.

M&L for two coats of cement base paint on new wall surfaces and all necessary preparation and wetting and curing, complete all as specified.

M&L for excavating in post holes (or similar holes) in hard/dense soil each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified.

M&L for RCC (Nominal mix) Type B0 1:2:4 (20mm graded aggregate) as in Columns, pillars, piers, posts and struts complete all specified and as directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and as directed.

S&F Fe-410-W(Gde E-250)quality B rolled mild steel in roof trusses(Framed)trusses, purlin, crane gantries, rails and framing(beam, tee, angle, channel or flat section)including distance pieces , cleats etc, complete all as specified and as directed.

S&F MS Fe-410- W(Gde- E-250) quality-B Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment as in covering the duct etc, complete all as specified and as directed.

M&L for two coats of ready mix paint, dead black paint etc for treating surfaces of steel and iron work, any descrfiption, width or girth complete all as specified and as directed.

Preparation of New steel and iron surfaces of any description, not otherwise described two coats of synthetic enamel paint over and including a coat of red oxide primer, complete all as specified and as directed.

S&F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws complete all as specified and as directed.

S&F prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges, fascia, valleys, gutters etc. fixed with self tapping screws complete all as specified and as directed.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110MM PVC SWR Bends any radius complete all as specified and directed.

Bairagi Builders

NIKHIL KOLESH