CONSTRUCTION OF NEW BUILDING OF WORKING WOMENS HOSTEL AT KAKKANAD - PHASE II

Amount

STEEL WORK

10.16.3 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Electric resistance or induction butt welded tubes

od171968/2021_2022 : Providing and fixing S.S fan clamp of 16mm dia in RCC slabs, beams including cost and conveyance of all materials,labour charges etc complete as directed by the Engineer-in-Charge at all levels.<br>

10.28 : Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

13.50.4 : Applying priming coat:With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel work (second coat)

13.61.1 : Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

FLOORING WORK

11.41.2 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

11.46.2 : Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

11.37 : Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

8.31 : Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

22.5 : Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

11.55.1 : Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

8.5 : Extra for providing opening or required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

16.92 : Providing and fixing 10x10x7.50 cm Granite stone block hand cut and chisel dressed on top, for paving in floors, drains etc. laid over 20mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints 10 mm wide filled with same mortar including ruled pointing etc. complete as per direction of engineer-in-charge

FINISHING WORK

13.16.1 : 6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.2.1 : 15 mm cement plaster on the rough side of single or half brick wall of mix:1:4 (1 cement :4 fine sand)

13.10 : 15 mm cement plaster 1:3 ( 1 cement :3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall.

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.47.1 : Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

13.60.1 : Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

22.6 : Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : a) after surface preparation, first layer of slurry of cement @ 0.488 kg/ sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. laying second layer of fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/ sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. d) fourth and final layer of brick tilling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured)

13.67.2 : Varnishing with varnish of approved brand and manufacture :Two or more coats glue sizing with spar varnish or an under coat of flatting varnish

MISCELLANEOUS BUILDING WORK

2.34.1 : Supplying chemical emulsion in sealed containers including delivery as specified.Chlorpyriphos / Lindane emulsifiable concentrate of 20%

2.35.3.1 : Diluting and injecting chemical emulsion for POST -CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion):Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

19.6.2 : Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand) including testing of joints etc. complete:150 mm dia R.C.C. pipe

19.6.4 : Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand) including testing of joints etc. complete:300 mm dia R.C.C. pipe

od171969/2021_2022 : Supplying and fixing of following sizes of medium duty PVC conduits conforming to IS 9537/1983 part III along with accessories in surface /recess including cutting the wall and making good the same in case of recessed conduit as required-32 mm dia

od171970/2021_2022 : Supplying and fixing of following sizes of medium duty PVC conduits conforming to IS 9537/1983 part III along with accessories in surface /recess including cutting the wall and making good the same in case of recessed conduit as required-25 mm dia

od171971/2021_2022 : Supplying and fixing of following sizes of medium duty PVC conduits conforming to IS 9537/1983 part III along with accessories in surface /recess including cutting the wall and making good the same in case of recessed conduit as required-20 mm dia

12.4.1 : Providing ridges or hips width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.0.80 mm thick with zinc coating not less than 275 gm/m2

od171973/2021_2022 : Providing and laying profiled sheeting 970mm to 1000mm cover width, 26/28mm crest height at 195-200mm centers, made out of '0.5mm TCT, Cold Rolled steel of 550 Mpa yield strength conforming to ASTM A 368 or AS 1595 with hot dip metalic coating 'of minimum 150gm/Sqm zinc-aluminium alloy coating mass (55% Aluminium, 43.5% zinc and 1.5% Silicon ) total of both size as 'per ASTM A 792 or AS1397. The colour have shall have a total coating thickness iof 35microns of polyster paint system as per 'AS/NZS - 2728:1997 ( category 3 ) of approved colour, comprising of 20 microns exterior coat on top surface and 5 microns reverse 'coat on back surface over 5 microns primer coat on both surfaces. Roofing sheet shall be factory cut and required length of '(up to 12mtr ) to suite site conditions and design drawings. Roofing sheet shall be crest fixed to purlines with hot dip 'galvanized self drilling fastners with integral EPDM washers (one fastner on each crest) also, fastners to be provided on side laps. 'Minimum sheet overlap at end laps shall be 150mm. Penetration and end laps in sheet shall be sealed by using proper sealant. 'Profiled HDPE fillers shall be provided wherever required to close voids between capings and troughs of the sheet to provide a 'weather tight exterior. Rate shall include cost and conveyence of all materials, lead, lift, scaffolding, all labour charges, making the roof water tight with required sealent etc complete at all level and as directed by Engineer-in-Charge.<br>

od171975/2021_2022 : Supplying and fixing in position PVC plain ended rain water gutter 150 mm or nearest size (semi circular section) of approved quality and design with all accessories like stop ends, 32x5mm MS flat supports at 1m interval, scaffolding etc. complete for all heights including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer- in-charge at all levels.<br>

16.69 : Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature jointed with cement mortar 1:3 ( 1 cement : 3 coarse sand) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge ( length of finished kerb edging shall be measured for payment ). ( Precast C.C. kerb stone shall be approved by Engineer-in-Charge)

PLUMBING AND SANITARY FITTINGS

18.8.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.20 mm nominal outer dia pipes

50.18.7.2.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge 20 mm dia 10 Kgf/cm2- Internal work - Exposed on wall

50.18.7.6.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 10 Kfg/cm - Internal work- Exposed on wall

50.18.9.9.1 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2

50.18.9.10.1 : Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2

50.18.9.22.3 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement-110 mm dia Door Elbow

50.18.9.22.1 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow

50.18.9.22.2 : Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow

50.17.1.5 : Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

17.3.1 : Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid

17.7.2 : Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630 x 450 mm with a single 15 mm C.P. brass pillar tap

18.51.1 : Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

18.52.1 : Providing and fixing C.P brass stop cock ( concealed) of standard design and of approved make conforming to IS: 893115 mm nominal bore

17.32.2 : Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 453x357 mm

18.65 : Providing and fixing PTMT Soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fittings arrangements, weighing not less than 106 gms.

17.73.2 : Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighting not less than 190 gms

od180611/2021_2022 : Providing and fixing 110mm PVC pipe fittings: PVC Y' Tee

od180612/2021_2022 : Providing and fixing 110mm PVC pipe fittings: PVC door tee

od180613/2021_2022 : Providing and fixing 150mm PVC pipe fittings: 45⁰

od180614/2021_2022 : Providing and fixing 150mm PVC pipe fittings: Coupling

od180615/2021_2022 : Providing and fixing 150mm PVC pipe fittings: PVC elbow

od180628/2021_2022 : Providing and fixing PTMT towel ring complete with CP brass screws with the concealed fitting arrangement of approved quality

18.64 : Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms.

17.60.1.1 : Providing and fixing trap of self cleansing design with screwed down or hinged grating without vent arm complete, including cost of cutting and making good the walls and floors:100 mm inlet and 100 mm outletSand cast iron S & S as per IS : 3989

od180629/2021_2022 : Providing and fixing PVC ball valve of an approved quality conforming to IS: 893: 25 mm nominal bore

od185854/2021_2022 : Providing and fixing PVC ball valve of an approved quality conforming to IS: 893: 40 mm nominal bore

od185855/2021_2022 : Providing and fixing PVC ball valve of an approved quality conforming to IS: 893: 50 mm nominal bore

od185853/2021_2022 : Providing and fixing shower cock, 15 mm nominal bore, weighing not less than 40 gms.

ADDITIONAL REQUIREMENTS

9.147A.1 : Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/- 0.2mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately)<br> Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 +/- 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.)

9.147A.3 : Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/- 0.2mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately)<br> Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement window double panels with top fixed with S.S. friction hinges (350 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. ( Area of window upto 2.50 sqm).

25.7 : Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Alumini um sheets (each0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

od185823/2021_2022 : Supplying and fixing powder-coated aluminium louvers by using 50mm x 25mm aluminium sections fixing with 20mm spacing to the backside with GP tube vertical support etc, complete&hellip;

od177529/2021_2022 : Providing and fixing SS coin mesh with 20mm dia openings and ISA 20X20X4mm frame for bird proofing including applying two coats of zinc chromate primer and two coats of synthetic enamel paint etc complete as directed by the engineer in charge&lt;br&gt;

10.3 : Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts,locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer .

od185824/2021_2022 : Supply and erecting 1.5HP bore well pump set submersible type 100mm dia CRI make including all fittings and connections etc. complete.

od185825/2021_2022 : Providing and fixing shelf door (two shutters)by using aluminium electroplated sections for outer frame with showcase frame and vertical members by using 11/2x1x1 mm thick box section,20mm lip section for shutter frame,3mm APP, and 4mm mirror fixing into the shutter frame and tighten with EPDM rubbers. 3&rsquo;&rsquo; SS hinges, handle, lock with key, etc. The top of the shelf is covered with two track sliding shutter by using an ordinary sliding section with lock and handle etc.. complete&hellip;

22.6 : Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : a) after surface preparation, first layer of slurry of cement @ 0.488 kg/ sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. laying second layer of fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/ sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. d) fourth and final layer of brick tilling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured)

18.48 : Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

18.36.1 : Constructing masonry chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for fire hydrants, with C.I surface box 350x350 mm top and 165 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 grades stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

21.2.1 : Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

13.85.1 : Applying priming coats with primer of approved brand and manufacture, having low VOC ( Volatile Organic Compound) content.With ready mixed pink or grey primer on wood work (hard and soft wood ) having VOC content less than 50 grams/ litre

13.48.2 : Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufacture

9.48.1 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding

11.20.1 Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand).Light shade pigment using white cement

9.141 Providing and fixing PVC Door Frame of size 50x47 mm with a wall thickness of 5 mm (±0.2mm), made out of single piece extruded PVC profile, with mitred cut joints and with 2 nos of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 x 15 mm & self driven self taping screws, the vertical door profiles to be reinforced with 40x20 mm M.S. rectangular tube of 0.8 mm, including providing EPDM rubber gasket weather seal throughout the frame, including jointing 5 mm PVC frame strip with PVC solvent cement on the back of the profile. The door frame to be fixed to the wall using 8x100 mm long anchor fasteners complete, all as per manufacturer's specification and direction of Engineer-in--charge.

9.142.2 35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded solid PVC ( ±0.2 mm) thick, having styles & rails (except lock rail ) of size 95 mmx 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinges side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm x 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm x 100 mm of cross section size 35 mm x 17 mm s 1 mm at each corner. Single piece extruded 5 mm thick solid PVC Lock rail of size 115 mm x 35 mm x 35 mm, out of which 95 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturer's specification and direction of Engineer-in-charge.Decorative finish (wood grained finish)

50.9.15.2 Supplying and fixing 300 mm Aluminium aldrop

od246715/2021_2022 Supplying and fixing C.I cover 600x600 mm with frame (standard pattern) the weight of cover to be not less than 9 Kg.

Rain water harvesting and its connecting works etc. complete.

ELECTRIFICATION

HT METERING PANEL WITH LBS

Supply, installation, testing and commissioning of 11KV Outdoor

Metering Panel with Load Break Switch fabriacted in CRCA

sheet steel of 2mm thickness with IP - 54 Protection comprising

of 3 Nos of 11KV */5A 10VA Class 0.2S CT and 1 Nos

11KV/110V, 20VA, Class 0.2 PT having separate chamber for

CT, PT and TOD Meter with provision for fixing TOD Meter

including Test Terminal Block, Control Fuses, KSEB sealing

provision and 1 Nos of 11 KV, 630A, 26.3 kA/1 sec Air break

manual front operated LBS with tripping coil rated for 230V AC,

mechanical trip push button, electrical trip push button, ON/OFF

indicator, earth switch, interlock between SFU and earth switch,

3 Nos of HRC fuses with suitable rating, space heater and

thermostat etc. complete with wiring and connections as

required. The panel shall conform to Electrical Inspectorate and

KSEB standards. This scope also includes the testing of CT,PT

and obtaining test certificate from KSEB / TMR. (*CT ratio will

be furnished later and all Statutory fees shall be remitted by the

Client /Consumer or it shall be reimbursed on the submission of

supporting documents).

HT ENERGY METER

Supply, installation, testing and commissioning of CT, PT

connected TOD Meter of approved brand and conforming to

relevant IS and KSEB, Electrical Inspectorate regulations, IP 51

with unbreakable transparent cover, provision for sealing,

anti-tamper features, real time and calibrated quartz clock tested

by KSEB.This scope also includes the testing of TOD Meter and

obtaining test certificate from KSEB / TMR. (*All Statutory fees

shall be remitted by the Client / Consumer or it shall be

reimbursed on the submission of supporting documents).

TRANSFORMER

Installation, testing and commissioning of 11KV/433V Three

Phase Oil Type 160KVA Outdoor Transformer with OLTC

conforming to Electrical Inspectorate and KSEB Standards. The

supply of transformer shall come within the scope of KEL.

NEUTRAL CT WITH ENCLOSURE

Supply and installation of 50/5 Resin cast class 5P10 10VA

Neutral CT with bar primary 25x6mm copper in a suitable

powder enclosure box with necessary wiring and earthing of the

box etc. complete as required.This scope also includes the testing

of CT and obtaining test certificate from Electrical Inspectorate.

(*All Statutory fees shall be remitted by the Client / Consumer or

it shall be reimbursed on the submission of supporting

documents).

EMERGENCY PUSH BUTTON

Supply, installation, testing and commission of Emergency

Stop Push Button with enclosure for the Transformer

DG SET

Installation, Testing and Commissioning of 125 KVA, Three

Phase, 415V, 0.8 power factor, comprising of diesel engine, fuel

tank, alternator, base plate radiator, control panel with MCCB,

EFR with CT, starting equipment exciter, home silencer and all

necessary accessories etc. complete as required. (Including

Acoustic Enclosure). This scope also includes the testing of

Energy Meter, CTs, Relays etc and obtaining test certificate

from KSEB / Electrical Inspectorate. (*All Statutory Fees shall

be remitted by the Client / Consumer or it shall be reimbursed

on the submission of supporting documents). The supply of

DG SET shall come within the scope of KEL.

LT METERING PANEL

Supply, installation, testing and commissioning of cubicle

type Outdoor KSEB Metering Panel Board with Double Door

and Canopy fabricated in compartmentalised design from

CRCA sheet steel of 2mm thick for frame work, covers and

gland plates, cleaning and finishing complete with 7 tank

process for powder coating in approved shade having

250A capacity Aluminium alloy bars of high conductivity,

DMC/FRP bus bar supports, 2 Nos of common earth bar of

25 x 6 Copper Strip etc. complete as required. For MCCBs Ics

shall be 100% Icu. The Panel shall conform to the Electrical

Inspectorate and KSEB standards and it should only be

manufactured after getting approval from Electrical Inspectorate

and the Consultant.

Specification & Components

4 Nos - Bus bar Provision for fixing CTs

1 Nos - Provision for Fixing Three Phase Energy Meter

3 Nos - Open Type / Bakelite Fuse with suitable rating

1 Nos - 250A Neutral Link

1 Nos - 250A, 36kA 4 Pole Microprocessor based MCCB with

ROM and spreader

MAIN SWITCH BOARD

Supply, installation, testing & commissioning of CPRI approved

cubical type Main Switch Board Panel suitable for 415V, Three

Phase, 4 Wire 50 Hz AC supply system having sufficient front

surface area fabricated in compartmentalised design from CRCA

sheet steel of 2 mm thick for frame work and covers, 3 mm

thick for gland, plates, cleaning and finishing complete with 7

tank process for powder coating in approved shade, having

320 Amps capacity extensible type TPN Aluminum alloy bus

bars of high conductivity, DMC / SMC / FRP bus bar supports,

with short circuit withstand capacity of 31 MVA for 1 Sec.,

bottom base channel of MS section not less than 100 mm x

50 mm x 5 mm thick, fabrication shall be done in transportable

sections, entire panel shall have a common copper earth bar

of size 25 mm x 6 mm at the rear with 2 Nos. earth stud, solid

connections from main bus bar to switch gears with required

size of AL. bus bars and control wiring with 1.5 Sq.mm PVC

insulated LSZH (Low Smoke Zero Halogen) copper conductor

cables, cable alleys etc. For all MCCBs Ics shall be 100% Icu.

The panel shall conform to the Electrical Inspectorate standards

and it shall only be manufactured after getting approval from the

Electrical Inspectorate and the consultant.

Busbar

1 Runs of 40 x 10mm AL.Busbar for each Phase

1 Runs of 32 x 10mm AL.Busbar for Neutral

EB Side

1 Nos - 250A, 36kA 4P Microprocessor based MCCB set

at 213A with 3 O/C and 1 E/F releases as Incomer

1 Set - RYB Indication lamps with Control MCBs

3 Nos - 250/5A CL:1, 10VA CT

1 Nos - Digital Multifunction Meter measuring V, A, F, KW,

KVA, PF with Control MCBs

1 Nos - 250A 4P Power Contactor (AC3)

1 Nos - Stand by Earth Fault Relay (In case of HT Connection)

or ELR with CBCT (In case of HT/LT or LT Connection)

DG Side

1 Nos - 200A 4P Isolator

1 Set - RYB Indication lamps with Control MCBs

3 Nos - 200/5A CL:1, 10VA CT

1 Nos - Digital Multifunction Meter measuring V ,A, F, KW,

KVA, PF with Control MCBs

1 Nos - 200A 4P Power Contactor (AC3)

1 Set - Contactor with Mechanical and Electrical Inter-lock

AMF control suitable for control of 125 KVA DG set complete

with AMF Relay with Control MCBs, Timer and all other

necessary accessories.

Surge Protection Device

2 Nos - 8 Module DIN Rail Mounting Type 1 + Type 2 +

Type 3 / Class 1 + class II 100kA SPD on incomer of EB supply

and DG Supply with all accessories etc. complete as required. The

connections to RYB Phases, Neutral and Earth shall be done

using 16 Sq.mm Single Core Flexible Copper conductor cables

with less than 0.45m in length.

Outgoings

1 Nos - 160A 36kA 4P Thermal Magnetic MCCB having 70 to

100% setting provision with ROM and spreader

3 Nos - 125A 36kA 4P Thermal Magnetic MCCB having 70 to

100% setting provision with ROM and spreader

2 Nos - 100A 36kA 4P Thermal Magnetic MCCB having 70 to

100% setting provision with ROM and spreader

2 Nos - 80A 36kA 4P Thermal Magnetic MCCB having 70 to

100% setting provision with ROM and spreader

APFC PANEL (45 KVAR)

Supply, installation, testing & commissioning of CPRI approved

cubical type Automatic Power Factor Correction Panel suitable

for 415 V, Three Phase, 4 Wire 50 Hz AC supply system having

sufficient front surface area fabricated in compartmentalized

design from CRCA sheet steel of 2 mm thick for frame work

and covers, 3 mm thick for gland, plates, cleaning and finishing

complete with 7 tank process for powder coating in approved

shade, having 200 Amps capacity type TPN Aluminum alloy bus

bars of high conductivity, DMC / SMC / FRP bus bar supports,

with short circuit withstand capacity of 31 MVA for 1 Sec.,

bottom base channel of MS section not less than 100 mm x

50 mm x 5 mm thick, fabrication shall be done in transportable

sections, entire panel shall have a common copper earth bar of

size 25 mm x 6 mm at the rear with 2 Nos. earth stud, solid

connections from main bus bar to switch gears with required

size of Al. bus bars and control wiring with 1.5 Sq. mm. PVC

insulated LSZH (Low Smoke Zero Halogen ) copper conductor

cables, cable alleys etc. For all MCCBs Ics shall be 100% Icu.

The panel shall conform to the Electrical Inspectorate standards

and it shall only be manufactured after getting approval from the

the Electrical Inspectorate and the consultant.

Busbar

1 Runs of 25 x 10mm AL.Busbar for each Phase

1 Runs of 25 x 6mm AL.Busbar for Neutral

Incomer

1 Nos - 160A 4P Isolator

1 Set - RYB Indication lamps with Control MCBs

3 Nos - 150/5A CL:1, 10VA CT

1 Nos - Digital Multifunction Meter measuring V, A, F, KW,

KVA, PF with Control MCBs

1 Nos - 8 Stage Microprocessor based APFC Relay

1 Nos - 250/5A CL:1, 10VA CT in EB Side of MSB

Surge Protection Device

1 Nos - 4 Module DIN Rail Mounting Type 1 + Type 2 100kA

SPD on Incomer side with all accessories etc. complete

as required. The connections to RYB Phases, Neutral and Earth

shall be done using 16 Sq.mm Single Core Flexible Copper

cables with less than 0.45m in length.

Outgoings

1 Nos - 40A TP MCB with Capacitor Duty Contactor and

15 KVAr Heavy Duty Cylindrical Type Capacitor

1 Nos - 40A TP MCB with Capacitor Duty Contactor having

provision for fixing 15 KVAr Heavy Duty Cylindrical Type

Capacitor in future

1 Nos - 32A TP MCB with Capacitor Duty Contactor and

10 KVAr Heavy Duty Cylindrical Type Capacitor

1 Nos - 32A TP MCB with Capacitor Duty Contactor having

provision for fixing 10 KVAr Heavy Duty Cylindrical Type

Capacitor in future

1 Nos - 16A TP MCB with 5 KVAr Heavy Duty Cylindrical Type

Capacitor

1 Nos - 16A TP MCB with Capacitor Duty Contactor and

5 KVAr Heavy Duty Cylindrical Type Capacitor

1 Nos - 16A TP MCB with Capacitor Duty Contactor having

provision for fixing 5 KVAr Heavy Duty Cylindrical Type

Capacitor in future

8 Nos - Green ON Push Buttons with Indicators

8 Nos - Red OFF Push Buttons with Indicators

2 Nos - Cooling Fan ( 6 Inches)

DISTRIBUTION BOARD

Supply and fixing of following ways surface / recess mounting,

vertical type, 415 V, TPN MCCB distribution board of sheet

steel, dust protected, duly powder coated, inclusive of 200A

tinned copper bus bar, common neutral link, earth bar, din bar

for mounting MCBs (But without MCCB/MCBs) as required.

6 Way , Double Door

Supply and fixing of following ways surface / recess mounting,

vertical type, 415 V, TPN MCB distribution board of sheet steel,

dust protected, duly powder coated, inclusive of 200A tinned

copper bus bar, common neutral link, earth bar, din bar for

mounting MCBs (But without MCCB/MCBs) as required.

8 Way , Double Door

6 Way , Double Door

Supply and fixing of following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415V, on

surface/recess, complete with tinned copper bus bar, neutral bus

bar, earth bar, din bar, interconnections, powder coated

including earthing as required. (But without MCB/RCCB/Isolator)

6 Way , Double Door

4 Way , Double Door

Supply and fixing following rating and breaking capacity and pole

MCCB with thermal magnetic release having 70 to 100% setting

provision with terminal spreaders in the existing MCCB DB

complete with connections, testing and commissioning etc. as

required.

63A to 100A 25kA 4 Pole MCCB

Supply and fixing following rating, four pole, (three phase and

neutral), 415V, Residual Current Circuit Breaker (RCCB), having

a sensitivity current 30 mA in the existing MCB DB complete

with connections, testing and commissioning etc. as required.

Supply and fixing following rating, four pole, (three phase and

neutral), 415V, Residual Current Circuit Breaker (RCCB), having

a sensitivity current 100 mA in the existing MCB DB complete

with connections, testing and commissioning etc. as required.

Supply and fixing 5A to 32A rating, 240/415V, 10kA, C Curve,

miniature circuit breaker suitable for inductive load of the

following poles in the existing MCB DB complete with

connections, testing and commissioning etc as required.

Single Pole

Double Pole

Three Pole

40A to 63A Three Pole

MCB DUMMY

Supply and fixing single pole blanking plate in the existing MCB

DB complete etc. as required.

ISOLATOR

Supply and fixing following rating, four pole, 415V, isolator in

the existing MCB DB complete with connections, testing and

commissioning etc. as required.

63A 4P Isolator

40A 4P Isolator

Supply and fixing following rating, double pole, 240V, isolator in

the existing MCB DB complete with connections, testing and

commissioning etc. as required.

63A 2P Isolator

40A 2P Isolator

METAL ENCLOSURE

Supply and fixing Sheet Steel enclosure on surface / recess

having provision to fix MCB/Isolator complete with connections,

testing and commmissioning etc. as required.

HT CABLE

Supply, laying, testing and commissioning of 11 KV grade XLPE

insulated armoured cables of the following size and laying in

earth excavated trenches, clamping in built up trenches, trays

using heavy duty Aluminium or GI Flat or by using heavy duty

GI spacer saddles and on 11 KV pole structure using necessary

heavy duty GI supports and clamps of which spacing of clamps

not exceeding 40cm and pulling through pipes etc. including all

minor civil works.

3C x 300 Sq.mm

3C x 240 Sq.mm

3C x 185 Sq.mm

3C x 150 Sq.mm

LT CABLES

Supply, laying, testing and commissioning of PVC 1.1 KV grade

XLPE insulated armoured Aluminium / Copper cables of the

following sizes and laying in earth excavated trenches, clamping

in built up trenches, trays, racks, risers, trusses, walls etc. using

using heavy duty Aluminium Flat or heavy duty GI spacer

saddles of which spacing of clamps not exceeding 50cm and

pulling through pipes including all minor civil works.

3.5C x 185 Sq.mm Al. cable

3.5C x 150 Sq.mm Al. cable

3.5C x 120 Sq.mm Al. cable

3.5C x 95 Sq.mm Al. cable

3.5C x 70 Sq.mm Al. cable

3.5C x 50 Sq.mm Al. cable

3.5C x 35 Sq.mm Al. cable

4C x 25 Sq.mm Al. cable

4C x 16 Sq.mm Al. cable

4C x 10 Sq.mm Al. cable

4C x 6 Sq.mm Al. cable

4C x 4 Sq.mm Al. cable

4C x 2.5sq.mm. Copper Armoured cable

2C x 2.5sq.mm. Copper Armoured cable

4C x 1.5sq.mm. Copper Armoured cable

2C x 1.5sq.mm. Copper Armoured cable

HT END TERMINATION

Supply and making outdoor cable end termination with heat

shrinkable jointing kit complete with all accessories including

lugs, additional sleeves etc suitable for following size of 3 core,

XLPE Aluminium conductor cable of 11KV grade as required.

Supply and making indoor cable end termination with heat

shrinkable jointing kit complete with all accessories including

lugs, additional sleeves etc suitable for following size of 3 core,

XLPE Aluminium conductor cable of 11KV grade as required.

GLANDING AND TERMINATION

Supply and making end termination with brass compression

gland and alluminium lugs for following size of PVC insulated

and PVC sheathed/ XLPE Aluminium conductor cable of 1.1KV

grade as required.

3.5C x 185 Sq.mm Al. cable

3.5C x 150 Sq.mm Al. cable

3.5C x 120 Sq.mm Al. cable

3.5C x 95 Sq.mm Al. cable

3.5C x 70 Sq.mm Al. cable

3.5C x 50 Sq.mm Al. cable

3.5C x 35 Sq.mm Al. cable

4C x 25 Sq.mm Al. cable

4C x 16 Sq.mm Al. cable

4C x 10 Sq.mm Al. cable

4C x 6 Sq.mm Al. cable

4C x 4 Sq.mm Al. cable

4C x 2.5sq.mm. Copper Armoured cable

2C x 2.5sq.mm. Copper Armoured cable

4C x 1.5sq.mm. Copper Armoured cable

2C x 1.5sq.mm. Copper Armoured cable

GLAND EARTHING

Supply and providing gland earthing using Aluminium or copper

strip / shim / wire using copper sockets etc. complete as

required conforming to Electrical Inspectorate Standards.

3.5C x 185 Sq.mm Al. cable

3.5C x 150 Sq.mm Al. cable

3.5C x 120 Sq.mm Al. cable

3.5C x 95 Sq.mm Al. cable

3.5C x 70 Sq.mm Al. cable

3.5C x 50 Sq.mm Al. cable

3.5C x 35 Sq.mm Al. cable

4C x 25 Sq.mm Al. cable

4C x 16 Sq.mm Al. cable

4C x 10 Sq.mm Al. cable

4C x 6 Sq.mm Al. cable

4C x 4 Sq.mm Al. cable

4C x 2.5sq.mm. Copper Armoured cable

2C x 2.5sq.mm. Copper Armoured cable

4C x 1.5sq.mm. Copper Armoured cable

2C x 1.5sq.mm. Copper Armoured cable

PLATE EARTHING

Supply and providing earthing with CI earth plate 1200mm x

1200mm x 12.6mm thick electrode including accessories, and

providing masonary enclosure with cover plate having locking

arrangement and watering pipe of 2.7 meter long etc. with

charcoal/coke and salt as required conforming to relevant IS,

Electrical Inspectorate standards etc.

Supply and providing earthing with CI earth plate 600mm x

600mm x 6mm thick electrode including accessories, and

providing masonary enclosure with cover plate having locking

arrangement and watering pipe of 2.7 meter long etc. with

charcoal/coke and salt as required conforming to relevant IS,

Electrical Inspectorate standards etc.

EARTHING CONDUCTORS

Supply and providing the earth conductors of the following sizes

and laying in earth excavated trenches, clamping in built up

trenches , walls, trays, racks, risers, trusses, etc. using heavy

duty Aluminium Flat or heavy duty GI spacer saddles of which

spacing of clamps not exceeding 90cm without making holes in

the earthing conductor and pulling through pipes including all

minor civil works. All the joints shall be properly tinned and

all connections shall only be done using SS Nut and Bolts with

double washers etc. complete as required.

25 x 6 mm Copper Strip

25 x 3 mm Copper Strip

8 SWG Copper Wire

10 SWG Copper Wire

MS STRUCTURALS

Supply, fabrication and installation of cable tray and supports

using M.S angles and plates of adequate size painted with one

coat of epoxy primer and two coats of epoxy grey paint.

Supply, fabrication and installation of Transformer, Panel Board

mounting supports using C Channels of adequate size painted

with one coat of epoxy primer and two coats of epoxy grey

paint.

Supply, fabrication and installation of checkered plates of 6mm

thickness to use above the cable trenches duly supported with

channels and duly painted with one coat of epoxy primer and

two coats of epoxy grey paint.

DG EXHAUST PIPING

Supply and laying of 100mm dia exhaust line with flexible

including bends, flanges, nut, bolt, packing, necessary supports

etc. and painting the same using Heat resistant Aluminium paints.

Supply and laying of 150mm dia exhaust line with flexible

including bends, flanges, nut, bolt, packing, necessary supports

etc. and painting the same using Heat resistant Aluminium paints.

Providing thermal insulation of exhaust line glass wool with AL.

Sheet, chicken mesh, necessary supports and screws.

CABLE ROUTE MARKER

Supply and fixing cable route marker with 10 cm x 10 cm x

5 mm thick G.I. plate with inscription there on, bolted / welded

to 35 mm X 35 mm X 6 mm angle iron, 60 cm long with

painting and fixing the same in ground at 5 meter intervel with

cement concrete in M.15 Grade (1:2:4) etc. complete as required.

PIPES FOR CABLE PROTECTION

Supply and laying of the following size medium class GI pipe in

ground or clamping in wall/ceiling with heavy duty GI or

Aluminium clamps etc complete as required.

150mm dia

100mm dia

80mm dia

50mm dia

25mm dia

Supply and laying of the following size DWC HDPE pipe ISI

marked along with all accessories like socket, bend, couplers etc.

conforming to IS 14930, Part II complete with fitting and

cutting, jointing etc. in the existing trench, complete as required.

200mm dia

160mm dia

120mm dia

90mm dia

63mm dia

POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point

with 1.5 sq.mm FRLS PVC insulated copper conductor single

core cable in surface / recessed medium class PVC conduit, with

with modular switch, modular plate, suitable GI box / PVC

surface box and earthing the point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable etc. as required.

Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface/recessed

medium class PVC conduit, 2 way modular switch, modular

plate, suitable GI box / PVC surface box and earthing point with

1.5 sq.mm FRLS PVC insulated copper conductor single core

cable etc. as required.

Wiring for group controlled (looped) light point / fan point /

exhaust fan point / call bell point (without independent switch

etc.) with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed medium PVC conduit, and

earthing the point with 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable etc. as required.

Group C

Supply and fixing two module stepped type electronic fan

regulator on the existing modular plate switch box including

connections but excluding modular plate etc. as required.

Supply and fixing suitable size GI box /PVC surface box with

modular plate and cover in front on surface or in recess including

recess including providing and fixing 6 pin 16/20 A modular

socket outlet and 20 A DP modular switch, connections etc.

as required.

Supply and fixing suitable size GI box /PVC surface box with

modular plate and cover in front on surface or in recess including

recess including providing and fixing 3 pin 5/6 A modular socket

outlet and 5/6 A modular switch, connections etc. as required.

Supply and fixing suitable size GI box /PVC surface box with

modular plate and cover in front on surface or in recess including

providing and fixing 2 Nos. 3 pin 5/6 A modular socket outlet and

2 Nos of 5/6 A modular switch, connections etc. as required.

(For light plugs to be used in non residential buildings).

Supply and fixing suitable size GI box / PVC surface box with

modular plate and cover in front on surface or in recess including

providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet

and 15/16 A modular switch, connections etc. as required

Supply and fixing following size/ modules, GI box / PVC surface

box along with modular base and cover plate for modular

switches in surface or in recess etc. as required.

1 or 2 Module

3 Module

4 Module

6 Module

8 Module

12 Module

Supply and fixing following modular switch/socket on the

existing modular plate and switch box including connections etc.

as required.

5/6A switch

3 pin 5/6A socket outlet.

6 pin 15/16A socket outet

Telephone socket outlet

TV antenna socket outlet

Data socket outlet

Supply and fixing 3 pin, 5A ceiling rose on the existing junction

box/wooden block including connections etc. as required.

Supply and fixing modular blanking plate on the existing modular

plate & switch box excluding modular plate as required.

CIRCUIT WIRING

Wiring for circuit / submain wiring along with earth wire with the

following sizes of FRLS PVC insulated copper conductor, single

core cable in surface / recessed medium class PVC conduit as

required.

2 x 1.5 sqmm + 1 x 1.5 sq.mm earth wire

2 x 2.5 sqmm + 1 x 2.5 sq.mm earth wire

2 x 4.0 sqmm + 1 x 4.0 sq.mm earth wire

2 x 6.0 sqmm + 1 x 6.0 sq.mm earth wire

TELEPHONE, TV, DATA WIRING & CCTV WIRING

Supply and drawing following pair 0.5mm dia FRLS PVC

insulated annealed copper conductor, unarmoured telephone cable

cable in the existing surface/recessed PVC conduit as required.

Supply and drawing co-axial TV cable RG-6 grade, 0.7mm solid

copper conductor PE insulated, shielded with fine tinned copper

braid and protected with PVC sheath in the existing surface/

recessed PVC conduit as required.

Supply and drawing of UTP 4 pair CAT 6 LAN Cable in the

existing surafce/recessed PVC conduit as required.

1 run of cable

Supply and drawing of 3+1 CCTV Camera Cable in the surface/

recessed PVC conduit as required.

SUPPLY AND LAYING OF CONDUITS

Supply and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including cutting

the wall and making good the same in case of recessed conduit

as required.

SUPPLY OF LIGHT AND OTHER ITEMS

Supply and providing the following fittings and items at site

Battern/Angle Holder

LED Bulb (up to 12W)

3W LED Deep Junction Box Light

LED Tube Set of 1 x 20W with Tube

12W LED Bulk Head

50W LED Flood Light

100W LED Flood Light

26W BLDC Ceiling Fan of Sweep 1200mm

High Speed Shutter Type Exhaust Fan of Sweep 150mm

Heavy Duty Metal Type Exhaust Fan of Sweep 450mm

INSTALLATION OF LIGHT AND OTHER FIXTURES

Installation, testing and commissioning of PVC battern / angle

holder fitting complete with all accessories directly on ceiling/wall

including giving connections etc. as required.

Installation, testing and commissioning of 3W LED Light in Deep

Junction Box complete with all accessories directly on ceiling

including giving connections etc. as required.

Installation, testing and commissioning of pre-wired, flourescent

fitting/compact flourescent fitting of all types complete with all

accessories and tube/lamp etc. directly on ceiling/wall, including

connections with 1.5 sq.mm FRLS PVC insulated, copper

conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of 50W LED Flood light

fittings complete with all accessories directly on wall/pillar/ceiling

including giving connections etc. as required.

Installation, testing and commissioning of 100W LED Flood light

fittings complete with all accessories directly on wall/pillar/ceiling

including giving connections etc. as required.

Installation, testing and commissioning of ceiling fan, including

wiring the down rods of standard length (up to 30cm) with 1.5

sq.mm FRLS PVC insulated, copper conductor , single core

cable etc. as required

Installation of exhaust fan in the existing opening, including

making good the damage, connection, testing, commissioning etc.

as required.

up to 450mm sweep

AIR CONDITIONER

Supply, installation, testing and commissioning of 1 TR inverter

5 star rated split AC with fully copper condensing unit, with

copper piping up to 5 meters.

Supply, installation, testing and commissioning of 4KVA wide

range, single phase, 50Hz, 170V-270V AC voltage stabilizer.

Supply of outdoor support stand for condensing unit of the 1 TR

split AC unit.

WATER PUMP

Supply, installation, testing and commissioning of 5HP/3.7KW

openwell submersible pump with head from 28 to 40M, with

8.0 to 3.8 LPS discharge, suction size 65mm and delivery size

50mm etc. complete as required. This scope does not include

SS ropes for hanging the pump and/or any piping works etc.

Supply, installation, testing and commissioning of 3HP/2.2KW

openwell submersible pump starter complete with connections

as required.

SAFETY EQUIPMENTS

Supply and fixing HT danger notice plate of 250 mm x 200mm,

made of mild steel at least 2mm thick and vitreous enameled

white on both sides and with inscriptions in signal red colour on

front side as required.

Supply and fixing MV danger notice plate of 200 mm x 150mm,

made of mild stee,l at least 2mm thick and vitreous enameled

white on both sides and with inscriptions in signal red colour on

front side as required.

Supply and fixing 2Kg Dry Chemical Powder (DCP) type fire

extinguisher complete with Gun Metal cap, hose with squeeze

grip nozzle, wall fixing brackets conforming to BIS: 2171 and

with ISI mark

Supply and fixing safety instruction chart in word duly framed in

good frame work as required.

Supply and providing a set of 2 Nos. 9.5 Litre capacity GI bucket

painted in post office red colour with prior coat of red oxide paint

and written with white paint "FIRE" and mounted on MS angle

iron frame with bracket of appropriate size and capacity including

filling sand etc.

Supply and providing First Aid Box as approved by St.John

Ambulance Brigade / Indian Red Cross conforming to IS 2217 : 1963

Supply and fixing laminated shock treatment chart duly mounted

on a good frame work

Supply and providing electrical grade rubber mat of size 2m x 1m

having 12mm thickness in front of panels and DBs conforming to

IS 15652 : 2006 standard.

Supply and providing electrical grade rubber mat of size 2m x 1m

having 6mm thickness in front of panels and DBs conforming to

IS 15652 : 2006 standard.

Supply and providing tested industrial safety helmet conforming

EARTH EXCAVATION AND BACK FILLING

Excavation of all types of soils for the laying of XLPE insulated

power cable, GI / HDPE / RCC Pipes, Earthing Copper

conductors to the required width and depth up to1.2m and back

filling after providing sand cushioning and protective covering by

laying bricks breadth wise above the cable. The supply of sand

and bricks will come within this scope. The trench dimensions

and specifications shall be as per the Electrical Inspectorate,

KSEB & CPWD standards.

Excavation and Back Filling

Supply and laying of Bricks

Supply and filling of sand

NAMING FOR IDENTIFICATION

Painting letters or figures of 2.5cm/4.5cm sizes with enamel paint

as identification mark to Panel boards, DBs etc as required.

DOCUMENTATION

Taking soil resistivity at site and obtaining test certificate from

Electrical Inspectorate (*All Statutory fees shall be remitted by

the Client / Consumer or it shall be reimbursed on the

submission of supporting documents).

Preparation of drawings and getting approval from Electrical

Inspectorate. (*All Statutory fees shall be remitted by the Client/

Consumer or it shall be reimbursed on the submission of

supporting documents).

Submission of completion report, arranging Inpsection and

obtaining Sanction Order from Electrical Inspectorate .(All

Statutory fees shall be remitted by the Client / Consumer or it

or it shall be reimbursed on the submission of supporting

documents.

Co-ordination with KSEB getting power allocation by the

submission of 7 sets of HT agreement and executing the

agreement etc or prepration of necessarry application,

drawings and submission to KSEB for getting HT/LT or

LT Connection. (All Statutory fees shall be remitted by the Client/

Consumer or it shall be reimbursed on the submission of

supporting documents.

Make of Electrical equipments/materials

All electrical materials/equipments shall be of best branded items with ISI, strictly as per schedule specification

Panel Boards: CPRI certified reputed manufacturers make

MCB/ELCB/DB - L&T/LEGRAND/SCHNEIRDER or equivalent

Cables & wires - Finolex/KEI/POLYCAB/RPG/V-GUARD

Switches/Sockets/Regulators - SCHEIDER/ABB/HAVELS/LEGRAND or equivalent

Rigid PVCPipes/Casing & Capping - A-ONE/REPUTED MAKE with ISI , Precession, Balco, GEO

Cable Glands & Sockets - REPUTED MAKE , Cosmos

Indicating Lamps - TEKINIC/RISHUB/STC, L&T, Schneider or equivalent

Ceiling/Exhaust fan: Havells, Orient, Usha, Crompton Greaves, Bajaj

Push Button- L&T, Schneider, Rishabh

Note :1 All materials, Items, Equipment shall be best branded items with IS and approved by client/KEL

2:Rate should be inclusive of Transportation, delivery and installation cost for all items

3.Rate should be Exclusive of GST.

4.Work should be executed as per DSR/PWD specification and direction of Engineer at site.

IBRAHIMKUTTY K K

AMJATH M A