REPAIR AND MAINT OF SOLAR WATER HEATER AND GEYSER CEILING FANS EXHAUST FANS AND ELECTRICAL FITTINGS IN MD OTM ACCN AT ALHILAL MIL STN UNDER GE PALAMPUR

Amount

Taking down geysers of any type and capacity due to rusting of bolts/seepage of wall, S&F heavy duty pin type fastener 4 inch long and making necessary inlet/outlet and electric water supply connections from existing source of geyser complete all as specified and as directed.

Inspection, checking adjustments and minor repairs of storage water heater 25/35/50Itr capacity of any type any make vertical/ horizontal type which includes the following:- (a) Inspection, taking out of drain plug & dewatering and re-fixing the same complete all as directed.(b) Checking water tightness of storage tank.(c) Checking stop cocks with outlet/inlet pipe of geysers, pressure reducing valves etc to ensure free movement of water and easy functioning of parts.(d) Inspecting over flow vent pipe connections to ensure water-tightness and proper flow.(e) Checking and correct earth continuity of electrical items. Checking functioning of heating element and correct setting adjustment of thermostat up to 55° C.(f) Adjustment of reducing valves, checking of dead weight type high pressure release valve.(g) The cost of spare parts required for repair & maintenance of geysers covered under this item shall be measured and paid separately under the relevant item as supply only. Note:- Irrespective of the Number of complaints, work against this item of BOQ shall be completed within 03 days after handing over the Complaint slip failing which recovery @ Rs 200.00/per geyser per day for delay shall be effected from the contractor payment.

Supply only heating element, 2 KW 230 volts, ISI marked suitable for 25 ltrs geysers of any make complete all as specified and as directed. Note: The contractor will visit E&M store Alhilal before quoting the tender for obtaining of samples

Supply only heating element 2 KW 230 volts, ISI marked suitable for 25 ltrs geysers of any make complete all as specified and as directed. Note: The contractor will visit E&M store Alhilal before quoting the tender for obtaing of samples

Supply only heating element, (Triangle type) 1.5 KW 230 volts, ISI marked suitable for 25/35/50 ltrs geysers of any make complete all as specified and as directed.

Supply only heating element, (Triangle type) 2 KW 230 volts, ISI marked suitable for 25/35/50 ltrs geysers of any make complete all as specified and as directed.

Supply only heating element, (Round type) 1.5 KW 230 volts, ISI marked suitable for 25/35/50 ltrs geysers of any make complete all as specified and as directed.

Supply only heating element, (Round type) 2 KW 230 volts, ISI marked suitable for 25/35/50 Itrs geysers of any make complete all as specified and as directed.

Supply only thermostat switch for geysers of 25/35/50 Itrs capacity (ISI marked) complete all as specified and as directed. Note: The contractor will visit E&M store Alhilal before quoting the tender for obtaing of samples

Supply only thermostat switch for geysers of 25/35/50 Itrs capacity (ISI marked) complete all as specified and as directed. Note: The contractor will visit E&M store Alhilal before quoting the tender for obtaining of samples

Supply only thermostat switch for geysers of 25/35/50 Itrs capacity (ISI marked) complete all as specified and as directed.

Supply only base assembly, compatible to existing geyser, with inlet and thermostat pipe with drain plug inclusive of clamps for holding the element with nuts, bolts and gasket complete all as specified and as directed.

Supply only indicator lamp for geyser of any type colour green & red complete all as specified and as directed.

Supply only stainless-steel inner tank of minimum 20 gauge sheet rated pressure not less than 7 kg/sq.cm suitable for 25 Itrs capacity geysers (wt not less than 3.75 kg) as per sample complete all as specified and as directed.

Supply only of stainless-steel inner tank of minimum 20 gauge sheet rated pressure not less than 7 Kg/sq.cm suitable for 50 Itrs capacity geysers (wt not less than 5.25 kg) as per sample complete all as specified and as directed.

S&F in repairs PVC connection for hot/cold water made of double layer nylon braided and fabric at a pressure of 6 kg/sq. cm at both ends, 450mm long, heavy duty with CP brass adopters, washers, suitable for 15mm bore pipe complete all as specified and as directed.

S&F in repairs PVC connection for hot/ cold water made of double layer nylon braided and fabric at a pressure of 6 kg/sq. cm at both ends, 600mm long, heavy duty with CP brass adopters, washers, suitable for 15mm bore pipe complete all as specified and as directed.

S&F in repairs bib taps, cast copper alloy, with crutch or butterfly handle chromium plated, fancy type, screwed down, screwed for 15mm bore iron pipe, IS marked, complete all as specified and as directed.

Dismantling carefully solar storage water heating system of any capacity, any type for following works with testing and re-fixing the same in original position making all water/ electric connection to entire satisfaction of Engineer-in-charge after repair as under:-(a) Inspection, opening, of all parts, descaling, washing of inner tank with chemical solution and cleaning of outer cover storage tank. (b) Checking water tightness of storage tank after cleaning. (c) Checking and correcting earth continuity of electrical items. (d) Adjustment of reducing valves, checking of dead weight type high pressure release valve and visual check of fusible plug for its intactness. Note: Supply and fixing of Spare parts, wiring etc shall be measured & paid separately.

Supply and fixing in repairs heating element, 3.00 KW 230 volts, ISI marked suitable for solar geysers tank of any make complete all as specified and as directed.

Supply and fix in repairs thermostat switch for solar water heater (ISI marked) any make and size complete all as specified and as directed. Make:- USHA/ Baja/Theta/Elcon.

S&F in repairs glass of heat collector for solar water heater 200/300/400 litre capacity complete all as specified and directed.

S&F in repairs tuffen glass of heat collector for solar water heater 200/300/400 litre capacity complete all as specified and directed.

Repair and welding to stainless steel water storage tank of solar storage water heating system of any capacity 100 to 500 LPD, to prevent any type of leakage at site with testing and re-fixing the same in original position making all water / electric connection to entire satisfaction of Engineer-in Charge after repair as under:-(a) Inspection, opening, of all parts, descaling, washing of inner tank with chemical solution and cleaning of outer cover storage tank.(b) Checking water tightness of storage tank after cleaning.(c) Checking and correcting earth continuity of electrical items.(d) Adjustment of reducing valves, checking of dead weight type high pressure release valve and visual check of fusible plug for its intactness.Note:- Supply and fixing of spare parts, wiring etc shall be measured & paid separately

Taking down old unserviceable electric water geyser, S&F new electric water storage Heater (vertical type Geysers) 50 Ltrs BEE RATING 5 STAR, 230 volts AC single phase with and including grouting with high tensile rag bolt, nut & washer etc as directed as per site requirement and making necessary inlet /outlet water connection for Geysers. Geysers to have glass lines tank, fero glass coated container, PUF insulation, glass coated heating element, 8 BAR rated pressure, thermostat cut off etc.complete all as specified and as directed. Note:- Old unserviceable electric water heater to be deposited in MES store yard.

Taking down old unserviceable electric water geyser, S&F new electric storage Heater (vertical type Geysers) 25 Ltrs BEE RATING 5 STAR, 230 volts AC single phase with and including grouting with high tensile rag bolt, nut & washer etc as directed as per site requirement and making necessary inlet / outlet water connection for Geysers. Geysers to have glass lines tank, fero glass coated container, PUF insulation, glass coated heating element, 8 BAR rated pressure, thermostat cut off etc. complete all as specified and as directed. Note:- Old unserviceable electric water heater to be deposited in MES store yard.

Taking down ceiling fan ,any size and sweep from its position after disconnecting electrical connection and transport it to workshop for servicing,dismantling for servicing including removal of bearing,bushes, condenser, connector, flaxible cord,split pin etc if required removing old grease and refill fresh, lubricating bushes alongwith new washers, cleaning and washing fan blades, fan body etc with soap solution after repairing re- assamble the same and transporting from workshop to any location in Alhilal Mil Station and fixing to position / location as directed by Engineer-in- charge, connecting to electric system, testing etc complete all as specified and directed by Engineer-in-charge: -Note: -(i) Replacement of parts/rewinding shell be measured and paid separately (ii) Quoted rate is deemed to be inclusive of transporting fan from any location in Army Area to MES store & taking down unserviceable/ defective parts.(iii) Item such as bearings, bushes, capacitor, shaft etc required for replacement shall be measured and paid seperately as supply only.

Taking down and transporting of exhaust fan 8'' (200mm) /9" (230mm)/10'' (250mm )/ 12" (300mm) / 15" (375mm)/ 18" (450mm) sweep from any location inside Alhilal Mil Stn to MES E/M Store Yard / Workshop for stripping of fan washing thoroughly of bearing / bush by petrol, washing / cleaning fan blade body etc thoroughly provision of new greasing replacement of worn-out / defective unserviceable parts (wherever necessary) assembling the same after defective / unserviceable parts is replaced including provision of twisted twin core flexible wire upto 0.7 mts long size 23/0.0076 (ISI marked) and re-fixing the same at the same location/other location including making good disturbed surface including testing to entire satisfaction of Engineer-in-charge. Note: -(i) Replacement of parts/rewinding shell be measured and paid separately (ii) Quoted rate is deemed to be inclusive of transporting fan from any location in Army Area to MES store & taking down unserviceable/ defective parts. (iii) Item such as bearings, bushes, capacitor, shaft etc required for replacemen shalled be measured and paid seperately as supply only.

S&F in replacement U clamp complete with nut bolt washer, split pin and rubber weal etc complete all as specified and directed by engineer in charge.

M&L cutting and taking out old burnout winding of any sweep ceiling fan and rewinding with same gauge of copper winding wire of superior quality including insulation materials varnishing etc and testing complete to entire satisfaction of Engineer- in- charge.

M&L cutting and taking out old burnout winding of 250 mm sweep exhaust fan and rewinding with same gauge of copper winding wire of superior quality including insulation materials varnishing etc and testing complete to entire satisfaction of engineer in charge.

M&L cutting and taking out old burnout winding of 300 mm sweep exhaust fan and rewinding with same gauge of copper winding wire of superior quality including insulation materials varnishing etc and testing complete to entire satisfaction of engineer in charge.

M&L cutting and taking out old burnout winding of 450 mm sweep exhaust fan and rewinding with same gauge of copper winding wire of superior quality including insulation materials varnishing etc and testing complete to entire satisfaction of engineer in charge.

S&F in replacement condensor 1.5 MFD suitable for ceiling fan / exhaust fan / wall mounting fan of any sweep complete all as specified and directed.

S&F in replacement condensor 2.5 MFD suitable for ceiling fan / exhaust fan / wall mountaining fan of any sweep complete all as specified and directed.

S&F in replacement condensor 4 MFD suitable for ceiling fan / exhaust fan / wall mountaining fan of any sweep complete all as specified and directed.

S&F in replacement ball bearing suitable for ceiling fan / exhaust fan / wall mounting fan of any sweep complete all as specified and directed.

S&F in replacement gun metal bush suitable for ceiling fan / exhaust fan / wall mounting fan of any sweep complete all as specified and directed.

S&F in repairs stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc complete all as specified and directed by engineer in charge.

M&L spray painting of ceiling fan, fan blades, down rod, canopy etc with a coat of synthetic enamel paint of approved colour and quality including preparation of old painted surfaces, cleaning etc and printing the MES fan numbers etc with black paint complete all as directed.

S&F motor of Exhaust Fan (plastic body) Capacity 200 mm including taking down of old unsv motor complete all as specified and directed.

S&F motor of Exhaust Fan (plastic body) Capacity 250 mm including taking down of old unsv motor complete all as specified and directed.

S&F 1200 mm sweep ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V. Min air delivery 210 CFM, Five star rating complete all as specified and directed.

S&F 250 mm sweep exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding, 5 star rated complete all as specified and directed. Note: Old unserviceable exhaust fan to be deposited in MES store yard.

S&F 300 mm sweep exhaust fan made of sturdy Engineering steel body complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding, 5 star rated complete all as specified and directed. Make :- Note: Old unserviceable exhaust fan to be deposited in MES store yard.

S&F new wall mounted fan 400 mm sweep with oscillating arrangement, inbuilt speed control and ON-OFF switch arrangement complete all as specified and as directed.Make :- Orient Model 400 mm Wall 44(with STING)/ Crompton TF SDX 120/ Havells Sprint LED.Note: Old unserviceable wall mount fan to be deposited in MES store yard.

S&F in repair LED lamp suitable for 14 watts, 240 volts, single phase, 50 Hz, Lumen 1450 AC supply (Warm White) complete all as specified and directed.

S&F in repair Linear aluminium batten LED T/L 20W aluminium extruded chanel powder coated with opaque diffuser for glare fee light (Warm White) complete with accessories internally prewired and including connecting up with twin core twiested flexible copper conductor cable with suitable size complete all as specified and directed.

Supply and installation 24 watt solar all-in-one street lighting with high efficiency Mono Crystalline Solar PV Module, Lithium Ferro Phosphate battery with in built BMS technology, high efficiengy LED, MPPT solar charge controller and aluminium extruded body & is specially programmed to automatically controlled the dimming and brightness of light, which increase the backup time in existing pole including taking old fittings complete all as specified and as directed with following specification. (i) Solar panel 60W (ii) LED power 24W (iii) Battery capacity 30Ah (iv) lumens (Im)>3120 lm (v) LED life time- 50000h (vi) Viewing angle-120 degree (vii) Charging time- 1 day (viii) Autonomy- 2 days (ix) CCT(K)- 5700K (x) working Temp- 10 degree to 50 degree (xi) Min weight- 18.5Kg

Dhani Builders (BID ID -3071065)

M/S MALHI CONSTRUCTIONS (BID ID -3070428)

M/S SAROOP ELECTRICAL & MECHANICAL WORKS (BID ID -3058979)

ess are electricals and electronic (BID ID -3062593)

M/s Sheetal Associates (BID ID -3062526)

PAWAN KUMAR GOVT. CONTRACTORS (BID ID -3069232)