Special repairs to 16 Govt married accn block No 170 1 to 8 and 171 1 to 8 of Bravo Power House colony under GE North Ambala Cantt

Amount

SCHEDULE A PART I (B/R WORKS)

Demolition of cement concrete (unreinforced) of any description in ground floor and pavings not exceeding 15cm thickness (below or above GL) complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position complete all as specified and directed. (Reinforcement cut as required to facilitate demolition)

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of brickwork built in cement mortar including all quoins, arches, pillars etc, complete all as specified and as directed.

Taking down chowkats or frames with shutter, area not exceeding 1.50 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes in wall/concrete for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces in CM (1:3) and finishing the surfaces to match with existing finish complete all as specified and directed.

Taking down chowkats or frames with shutter, area exceeding 1.50 Square metre and not exceeding 4.00 Square metre (without taking off shutters from frame) and removing from site, including cutting holes in wall/concrete for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces in CM (1:3) and finishing the surfaces to match with existing finish complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks etc., including cleaning or refixing or removal to Store (measured overall as fixed along the eenb'e line over fittings and accessories) complete all as specified and directed.

Dismantling of bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs,aprons, etc. (each layer), laid, bedded and pointed in any mortar all as specified and as directed.

Demolition of mud/mud phuska in roofs, any thickness, including plastering and leeping if any and cleaning the surface with wire brushes and removal of the same outside defence land complete all as specified and as directed.

Taking down cement or cement lime plaster, of any description, on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and as directed.

Taking up or down 15mm bore, steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 20mm bore, steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Dismantling overhead water tanks, of any description, of capacity exceeding 250 litres and not exceeding 500 litres complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipes, internal dia of pipe in 75/100mm, jointed in cement mortar and taking out of trenches/floor/wall, if required complete all as specified and as directed.

Material and labour for PCC (1:7:12), type F2 using 40mm graded stone aggregate as in foundation, filling and mass concrete for sunken portion complete all as specified and directed.

Material and labour for PCC (1:2:4) type B0 (using 12.5mm graded stone aggregates) as in coping, benching, bed blocks and the like including necessary form work and weathering, slightly rounded or chamfered angles and throating and finishing exposed surfaces of concrete fair and even complete all as specified and as directed.

Material and labour for providing cement concrete 1:2:4, type B0, using 12.5mm graded aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth, string, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed. Note: Reinforcement, if reinforced, shall be measured and paid separately.

Material and labour for precast reinforced cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregates, in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, balconies, canopies, deck slabs, shelves and similar articles with plain faces and setting in mortar cement mortar (1:4) with joints to match complete all as specified and directed.

Material and labour for precast reinforced cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregates, in chajjas and similar articles with plain faces and setting in mortar cement mortar (1:4) with joints to match complete all as specified and directed.

Material and labour for brickwork, with old size bricks, straight or curved on plan to any radius, exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed.

All as above Item No 1.20 but except bricks complete all as specified and as directed. Note: Old serviceable bricks as obtained from serial item No 1.04 hereinbefore shall be reused after cleaning the bricks. The rate quoted shall include for cleaning the bricks also.

Material and labour for brickwork, with old size bricks, straight or curved on plan to any radius, in half brick thick walls, built in cement mortar 1:4 complete all as specified and as directed.

Material and labour for applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @0.05 cu. m. per sq. m complete all as specified and as directed.

Material and labour for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends oredges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exceeding 10cm girth complete all as specified and as directed.

Material and labour for use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges for rough finished flat surfaces of concrete complete all as specified and directed.

Material and labour for plain fillets, leeping patti, square, rectangular or triangular in section, clean sawn, secured with nails or brads complete all as specified and directed.

Material and labour for flush shutters, 35mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Material and labour for second class hard wood glazed and skeleton shutters, 35mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, elc.;sizesof me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats

Supply and fixing of second class hard wood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessaty' labours; articles not exceeding 200 cu.cm each complete all as specified and directed.

Supply and fixing of solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

Supply and fixing of factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

Suuply and fixing of factory made UPVC white colour Sliding window of area not exceeding 2.00 Sqm each, three track, made of extruded profiles with wall thickness of 2.3mm (+/- 0.2mm). Window profile with hollow section with multi chamber, Frame (88mm x 52mm), sliding sash (42mm x 67mm), sliding mesh sash (42mm x 57mm), Sliding interlock (one vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be mitered cut and fusion welded at all corners, including railing of holes for fixing of hardware and drainage of wateretc., making arrangement for fixing hardware, EPDM gasket, 1.2 mm +/- 0.2mm thick galvanized steel frame (30mm x18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm), profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware (Touch lock of zinc alloyed (white powder coated), steel roller system, Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40mm and required accessories. Note:- The unit rate quoted by the contractor exludes cost of glass and includes all other accessories. Net opening will be measured for payment purpose.

Supply and fixing of stainless steel, butt hinges, 100mm size, medium weight, ISI marked and fixed complete all as specified and as directed.

Supply and fixing of aluminium anodised, 150mm long, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

Supply and fixing of aluminium handle, 150 mm long, cast type, anodized, ISI Marked complete, all as specified and as directed.

Supply and fixing of aluminium sliding door bolts, 300mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

Supply and fixing of mild steel, 150mm long, ordinary rat tail rod pattern springs for door including roller and roller plate, ISI marked complete all as specified and as directed.

Supply and fixing of stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

Supply and fixing mild steel works in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, bolts, hooks, hold fasts etc, similar articles conforming to Fe-290-Gde-E-165 complete all as specified and directed.

Material and labour for mild steel TMT bars, 10mm dia and over, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Material and labour for mild steel TMT bars, 6mm to 8mm dia as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Supply and fixing of pressed steel frames for doors of size 105x60mm, 1mm thick, with one or more rebates including, hold fasts of 25mm x 4mm FI, 25mm long, 6 Nos in each chowkhat, necessary lugs, 4 Nos 100 mm butt hinges medium weight, cold rolled, welded for each frame, lock strike plate, including sanding, tarring backs of chowkhats, one shop coat of red oxide zinc chrome primer, PCC 1:3:6 type C-0 filling in chowkhats, 2 Nos 12 mm dia tie bars at the bottom of frame etc complete all as specified and as directed.

Supply and fixing of pressed steel frames for doors of size 125x60mm, 1mm thick, with one or more rebates including, hold fasts of 25mm x 4mm FI, 25mm long, 6 Nos in each chowkhat, necessary lugs, 4 Nos 100 mm butt hinges medium weight, cold rolled, welded for each frame, lock strike plate, including sanding, tarring backs of chowkhats, one shop coat of red oxide zinc chrome primer, PCC 1:3:6 type C-0 filling in chowkhats, 2 Nos 12 mm dia tie bars at the bottom of frame etc complete all as specified and as directed.

Supplying and fixing of prelaminated particle board, 18/19mm thick, exterior grade, (Grade-I) conforming to IS-14587, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber framework of cabinet, shelf for cup board etc. including lipping patti including required size stainless steel hinges/pintle hinges and brass handles with all necessary items complete all as specified and as directed.

Material and labour for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust,etc. and brushing the surface with neat cement slurry @ 3.0kg of cement per sq. metre complete all as specified and as directed.

Material and labour for providing cement concrete 1:2:4, type B1, using 20mm graded aggregates, as in roof kerbs or mud stops, padding, rounded or chamfered on edges as in roof, finish even and fine using WPC complete all as specified and as directed. Note : Supply only WPC shall be measured and paid separately.

ACCESSIBLE ROOF TREATEMENTS : APP TREATMENT WITH BRICK/PCC TILES:- material and labour for providing and laying 3mm thick APP(atactic polypropylenepolmer) modified prefabricated five layer weight not less than 3.60 kg/Sqm water proofing membrane black finish reinforced with non woven polyster matt, make as approved consisting of a coat bitumious promer @ 0.40 ltr/ Sqm by the same membrane manufactures of density 0.87 to 0.89 kg/ltr at 25' C temprature and viscosity 70-160 cps over the primer coat, the layer membrane shell be laid using butane troch and sealing all joints etc after preparing the surace complete as per standred practic as per manufactures instuctions. The vital physical and chemical parameters of the membrane shell be under :- (i) Joint strength in logitudinal and transverse direction at 23'Cat 650/450 N/5 cms (ii) Tear strength in logitudinal and transverse 150'C when tested in accordance with ASTM (d-5147) (iii) The laying of membrane shall be got down through the authorised applicator of manufactures of membrane only. Note:- The contractor will carry out ponding test after application of APP treatment before claiming payment.

Material and labour for 40mm thick brick tiles laid on 15mm thick bed in cement mortar (1:6) and jointed and pointed in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on mud phuska complete all as specified and as directed.

All as above Item No 1.49 but except brick tiles complete all as specified and as directed. Note: Old serviceable brick tiles as obtained from serial item No 1.08 hereinbefore shall be reused after cleaning the tiles. The rate quoted shall include for cleaning the tiles also.

Material and labour for PCC (1:2:4) type B0 (using 12.5 mm graded stone aggregates), 25 mm thick, as in sub base of floors, finished rough and even to receive floor topping complete all as specified and as directed.

Material and labour for PCC 1:3:6 type C-1 (using 20 mm graded mechanically crushed stone aggregate), 50mm thick, as in plinth protection/PCC path and paving, laid in panels of area not exceeding 1.20 sqm with 12mm wide joints filled with mastic (using bitumen and sand mixture applied hot in the ratio of 1:3 by weight) formed at the end of each panel and change in direction of plinth protection/PCC Path and paving and finishing the top surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour for machine cut kota stone slab 16-20 mm thick ( size of each stone not less than 55cm x 55cm), laid in flooring, over and including cement screed bed 15mm thick in cement mortar (1:4) base and jointed & pointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Granite finish) complete all as specified and directed.

Material and labour for machine cut kota stone slab 16-18 mm thick laid on verticle surface or skirting, dado, riser to steps, pillars etc. over and including 10mm thick plaster in cement mortar (1:4) on brick work or concrete surfaces and jointed & pointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Granite finish) complete all as specified and directed. Note:- Size of slab shall be cut as required.

Material and labour for premium quality, anti skid, porcelain, coloured tiles (Square/rectangular), area of each tile exceeding 0.18 sqm and not exceeding 0.42 sqm and 7 to 8 mm thick, laid in floor over and including cement screed bed 15mm thick in cement mortar (1:4) and set and jointed in neat cement slurry @ 3.00 kg/Sqm and pointed in white or coloured cement to match the surface complete all as specified and directed.

All as per item No. 1.55 above but tile cut to size and 150 mm height and laid in vertical surfaces such as skirting, dado, riser to steps etc. over and including cement screed bed 10mm thick in cement mortar (1:4) and set and jointed in neat cement slurry @ 3.00 kg/Sqm and pointed in white or coloured cement to match the surface complete all as specified and directed.

Material and labour for premium quality, joint free, printed glazed coloured ceramic tiles of size 350x250x7mm/450 x 350 x 7mm thick on vertical surfaces of walls such as skirting, dado, riser to steps etc. over and including 10mm thick rough finished plaster in cement mortar (1:4), set, jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Material and labour for marble work, Baroda green, 16-18mm thick, one piece in width and length not less than 1.8 m (except in case of slab is more than 1.80 metre and less than 2.40 metre smaller size as approved by Engr-in-Charge may be used), laid over and including 15mm thick bedding layer in cement mortar (1:4), table rubbed & polished in shelves etc including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of marble including rounding of front edge and finally granite finish polishing with and including taking down the existing slab of any type complete all as specified and as directed.

Material and labour for rendering, 10 mm thick, in cement mortar 1:3, on surfaces of ceiling, finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6, finished even and smooth without extra cement all as specified and as directed.

Material and labour for rendering, 15 mm thick, in cement mortar 1:4, mixed with water proofing compound @ 3% by weight of cement or as per manufacturer’s instructions, on fair faces of brick work or concrete surfaces of any description finished even and smooth without using extra cement complete all as specified and as directed. Note: Supply only integral water proofing shall be measured and paid separately.

Supply only integral water proofing compound complete all as specified and as directed.

Material and labour of washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement : 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 kg of cement per square metre, top layer 15mm cement plaster 1: 1/2:2 (1 cement : 1/2 coarse sand : 2 stone chippling 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings. complete all as specified and directed .

Material and labour for preparation of old plastered surfaces of ceiling and applying two coats of white wash complete all as specified and as directed.

Material and labour for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

Material and labour for preparation of newly plastered wall surfaces and applying three coats of white wash complete all as specified and as directed.

Material and labour for preparation of old plastered surfaces of walls and applying two coats of white wash complete all as specified and as directed.

Material and labour for preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and as directed.

Material and labour for preparation of old plastered wall surfaces and applying two coats of cement base paint complete all as specified and as directed.

Material and labour for preperation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of chalk whitening over 2mm thick wall care putty complete all as specified and as directed.

Material and labour for complete removal of existing treatment on old/existing wall surfaces by using appropriate technique as approved by Engr-in-charge and applying two coats of oil bound distemper over 2mm thick wall putty over a coat of primer complete all as specified and as directed.

Material and labour for preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of approved colour synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Material and labour for preparation of new steel surfaces, of any description not otherwise described, over 10 cm width or girth and applying two coats of approved colour synthetic enamel paint, over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Material and labour for preperation of old/new plastered/unpolastered/washed stone grit plaster surfaces of wall, chajjas, balconies, facias etc and applying two coats of exterior emulsion paint of approved colour over a coat of alkali resistant primer complete all as per manufacturers instructions complete all as specified and directed.

Supply and fixing in repairs of MS powder coated decorative curtain rod, 20mm dia, and fixing with decorative brackets, stop rollers and finials at the end complete all as specified and directed.

Supply and fix in repair, stainless steel sink with draining board, made out of 1mm thick sheet for kitchen or laboratory with plug, washers, waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410x330mmx160mm including waste pipe and waste fittings, brass, chromium plated for glazed ware sinks, basins etc. with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed. Make:- Prayag/Jayna/Neelkanth

Supply and fixing in repair stainless steel plate rack 1mm thick of size 750 x 600 x 200mm weighing not less than 8 Kg each and fied with stainless steel screws to wall complete all as specified and directed. Make:- Prayag/Bluestar/Neelkanth/Jainko

Supply and fixing of mild steel almirah shutters with frame, exceeding 1.5 Square metre, made of 1mm thick mild steel sheet, in two leaves, as built in furniture in cupboards, including locking arrangement with mortice lock of mild steel, vertical type, 65mm size, 2 lever, ISI marked with duplicate keys and handle, etc. (all as per Godrej pattern) including two coats of approved colour synthetic enamel spray painting over a coat of red oxide primer complete fixed in brick or concrete wall with minimum six numbers of 10mm dia and 100mm long mild steel bolt with washer and nut in cement mortar (1:4) or PCC 1:2:4, type B-0 complete all as specified and directed.

Supply and fixing of GI tubing, ISI Marked, 15mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Supply and fixing of GI tubing, ISI Marked, 20mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Supply and fixing of water storage tank of 500 ltr capacity, HDPE triple layer, cylindrical, vertical with closed top and FDA approved, 100% UA stabilized, rust proof, ISI marked, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, ISI marked, screwed and suitable for iron pipe 20 mm bore complete all as specified and directed. Note:- Tank shall be white and make of tank shall be engraved on the tank.

Supply and fix in repair, grating doom 125 mm dia with waste hole of PTMT (Minimum weight 40gms) complete all as specified and directed.

Material and labour for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 100mm internal dia of pipe complete all as specified and directed.

Supply and fixing in repair stop valves, 15mm bore, fancy type, chromium plated, ISI marked, with long shank and cup (concealed type), cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. Note : (i) Weight of stop valve shall not be less than 0.575 Kg (ii) Make: Prayag/Prima/Parryware

Supply and fixing in repair stop valves, 15mm bore, fancy type, chromium plated, ISI marked, angle cock, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. Note : (i) Weight of stop valve shall not be less than 0.575 Kg (ii) Make: Prayag/Prima/Parryware

Supply and fixing stop valves, 15mm bore, fancy type, chromium plated, ISI marked, angle cock, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. Note : (i) Weight of stop valve shall not be less than 0.575 Kg (ii) Make: Prayag/Prima/Parryware

Supply and fixing in repair stop valves, 15mm bore, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. Make: Prayag/Prima/Parryware

Supply and fixing in repairs bib taps, 15mm bore, long body, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule or union and fixed complete all as specified and as directed. Note : (i) Weight of bib tap shall not be less than 0.575 Kg (ii) Make: Cera, Hindware, Parryware, Prima

Supply and fixing in repair stop valves, 20mm bore, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. Make: Prayag/Prima/Parryware

Supply and fixing in repair shower rose, 75 to 100mm size, chromium plated, with or without swivel joints any size including fixing to steel pipe or union complete all as specified and as directed. Make: Prayag/Prima/Parryware

Supply and fixing of brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges including brackets complete all as specified and directed. Make: Prayag/Prima/Parryware

Supply and fixing of PVC connections, 450 mm long and 15mm dia with brass nuts and PVC washers on both ends complete all as specified and directed.

Supply and fixing in repairs, vitreous china squatting pan of Orissa pattern, size 580mmx440mm, white (Ist quality) with ‘P’ or ’S’ trap, with front or back inlet and integral foot rests of any pattern including connections to existing trap, flushing pipe, anti syphonage pipe etc and provision of lime concrete bedding for fixing complete all as specified and directed. Make: Cera, Hindware, Parryware/Prayag

Supply and fixing of 10 litre capacity, virgin polypropylene cistern, ISI marked, coloured, low level, valveless syohonic action type, complete with PVC bend/flush pipe and making all connections including making good the disturbed surface to match with the existing surface complete all as specified and directed. Make: Cera, Hindware, Parryware/Prayag

Supply and fixing in repair, vitreous china wash down water closet, pedestal pattern (EWC), white, with 'P' or 'S' trap, with PVC water closet seat, black or white, closed pattern, with flat bottom and cover and mild steel chromium plated or aluminised hinging device and connecting to existing/new low level flushing cisterns, existing/new flush pipe and drain (or out going pipe) and fixing in position complete all as specified and directed Make: Cera, Hindware, Parryware/Prayag

Supply and fixing in repair, PVC floor trap with CP grating, 100mm dia outlet, including jointing to waste pipe and fixed in cement concrete (1:2:4) type B1 complete all as specified and directed.

Supply and fixing cast iron soil, waste and vent spun pipes, 100mm bore, in any length, with or without ears, with cement joints, laid in trenches or in floors complete all as specified and as directed.

Supply and fixing cast iron soil waste and vent spun pipes, 100mm bore, ISI marked, in any length, with or without ears, with cement joints, fixed to walls complete all as specified and as directed.

Supply and fixing cast iron soil waste and vent spun pipes, 75mm bore, ISI marked, in any length, with or without ears, with cement joints, fixed to walls complete all as specified and as directed.

Supply and fixing cast iron soil waste and vent spun pipes, 50mm bore, ISI marked, in any length, with or without ears, with cement joints, fixed to walls complete all as specified and as directed.

Supply and fixing cast iron soil, waste and vent spun pipes, 75mm bore, in any length, with or without ears, with cement joints, laid in trenches or in floors complete all as specified and as directed.

Supply and fixing for cast iron, 100mm bore, bends (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and as directed.

Supply and fixing for cast iron, 75mm bore, bends (any radius), diminishing pieces or tapers (larger bore measured), fitted with oval access door complete all as specified and as directed.

Supply and fixing cast iron branch pieces, 100mm bore, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, fitted with oval access door complete all as specified and as directed.

Supply and fixing cast iron branch pieces, 75 mm dia, single (equal or unequal), ordinary or inverted or with parallel branches fitted with oval access door complete all as specified.

Supply and fixing of 75mm bore cast iron cowls complete all as specified and as directed.

Supply and fixing of 50mm bore cast iron cowls complete all as specified and as directed.

Supply and fixing of salt-glazed stoneware gully traps, square or round mouthed, type 'P', of size 150 x 150mm set and jointed to drain pipe with cement mortar (1:1) including demolition of existing old unserviceable gully traps complete all as specified and directed.

Supply and fixing in repairs, 110mm dia PVC soil, waste, drain pipe, type ‘B’, conforming to IS 13592-1992, single socketed, in any length, with rubber rings joints or jointed with solvent cement, fixed to walls including clamps complete all as specified and as directed. Note- Rubber rings for pipes and fittings shall conform to IS 5382-1985.

Supply and fixing in repairs, PVC (SWR) bends/shoes,110mm bore, of any radius including jointing with solvent cement complete all as specified and directed.

Supply and fixing of CP nipple with flange fixing as in bib taps, stop cocks, angle cocks etc. complete all as specified and directed.

Supply and fixing of glazed white coloured ceramic tiles of size 150x75x5 or 6mm thick fixed in neat cement slurry including painting boldly Building No. or Quarter No. with black synthetic enamel paint complete all as specified and directed.

Material and labour for cutting holes through RCC shelf and marble slab as in cooking platform suitable for insertion of gas pipe complete all as specified and directed.

Supply and fixing of PVC waste pipe, 32/40mm dia, for wash hand basin/Kitchen sink etc. complete all as specified and directed.

SCHEDULE A PART II (E/M WORKS)

Taking down carefully any type of point wiring (light, fan, socket or power) complete with fittings such as switches, ceiling roses, pendants, regulators, sockets, tube light fittings with all accessories etc., and/or drawing out from existing conduit/batten and removal of materials from site and making good the disturbed surfaces of wall, floors, ceiling etc to match with the existing surfaces with matching OBD/White wash/Distemper complete all as specified and as directed.

Material and labour for concealed point wiring using approved colour coding as per IS, with multi stranded copper conductor 1.5 sqmm (Nominal area), single core, FRLSH, 1100 volts, ISI marked, PVC insulated and unsheathed stranded cable drawn through and including non metallic, medium grade PVC concealed conduit not less than 25mm to 32mm dia and its fittings including all tees, bell mouth pieces and fixing accessories such as couplers, saddlers, pipe hooks etc, PVC junction boxes, ISI marked including modular mild steel sunken boxes, made out of 1.6mm thick mild steel sheet metal conforming to IS-5139 (Pt-I)1969 and IS-14772-2000, with earth dolly, coated with two coats of anti corrosive paint over a coat of red oxide primer internally, covered with modular decorative cover plate over sunken boxes for housing of modular switches, socket outlets, fan regulators etc. with brass screws and washers including 1.5 sqmm single core PVC insulated and unsheathed FRLSH cable, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor upto common earth and connecting to common earth dolly with suitable size of lugs including making good the disturbed surfaces as per existing for one light point/bell point controlled by one switch complete all as specified and directed. Notes :- (i) Switch, socket, lamp holder, ceiling rose and fan regulators to be measured and paid for separately. (ii) PVC Conduit shall conform to IS 9537 part I & III. (iii) All chases will be cut by chase cutter only. Make of PVC Conduit- Finolex, Polycab, Kalinga Premium, Surya, Plaza, Diplast Make of PVC wire- Finolex, Polycab, Havells, RR Kabel, Grandlay, L&T

Description all as per Srl item No.02 here in before but for one ceiling fan/exhaust fan point controlled by one switch and regulator.

Description all as per Srl item No.02 here in before but for one 3 pin socket outlet point 5 Amp on same board.

Description all as per Srl item No.02 here in before but for one 3 pin socket outlet point 5 Amp on independant board.

All as per the description of Serial Item No 2.02 above, but with 4.0 Sqmm PVC, FRLSH, unsheathed, multistranded cable, for one socket point 15 & 5 Amps, 1100 volts grade, ISI marked, including 4.0 Sq mm size, green colour, PVC insulated FRLSH, continuous copper earth wire and connected to common earth dolly complete all as specified and as directed. Note- Switch, Socket shall be measured and paid separately and Steel junction boxes shall be used wherever junction boxes are to be fitted.

Supply and fixing of switch modular, 6 Amps, one way, one module, single pole, 230 volt complete all as specified and directed. Make: Legrand (Arteor)/ Schenider (Zencelo)/ Hager (Insista)/ ABB (Cherion)/ L&T (Englaze).

Supply and fixing of switch modular, 16 Amps, one way, one module, single pole, 230 volt complete all as specified and directed. Make: Legrand (Arteor)/ Schenider (Zencelo)/ Hager (Insista)/ ABB (Cherion)/ L&T (Englaze).

Supply and fixing of socket modular, 2/3 pin, 5 amps, one way, two module, single pole, 230 volts complete all as specified and directed. Make: Legrand (Arteor)/ Schenider (Zencelo)/ Hager (Insista)/ ABB (Cherion)/ L&T (Englaze).

Supply and fixing of socket modular, 2/3 pin, 6/16 Amps, one way, two module, single pole, 230 volts complete all as specified and directed. Make: Legrand (Arteor)/ Schenider (Zencelo)/ Hager (Insista)/ ABB (Cherion)/ L&T (Englaze).

Supply and fixing of electronic fan regulator, step type, modular, 450 watt, two module, flush type complete all as specified and as directed. Make: Legrand (Arteor)/ Schenider (Zencelo)/ Hager (Insista)/ ABB (Cherion)/ L&T (Englaze).

Supply and fixing of Bell push, modular type, 5/6 Amps, 230 Volts, one module complete all as specified and as directed. Make: Legrand (Arteor)/ Schenider (Zencelo)/ Hager (Insista)/ ABB (Cherion)/ L&T (Englaze).

Supply and fixing of Calling bell, AC, 230 Volts, 50Hz, single pole complete all as specified and as directed. Make: Legrand (Arteor)/ Schenider (Zencelo)/ Hager (Insista)/ ABB (Cherion)/ L&T (Englaze).

Supply and fixing of metal clad enclousure for geyser along with a three pin socket, SPN and earth plug and top, 20 Amps MCB, SP, complete all as specified and as directed. Make: Legrand (Arteor)/ Schenider (Zencelo)/ Hager (Insista)/ ABB (Cherion)/ L&T (Englaze).

Supply and fixing of mirror light 9/12 W LED wall mounting fixture, compact and energy efficient epoxy powder coated CRCA light luminaire, including disconnecting and taking down existing old unserviceable fitting and removing complete all as specified and as directed. Make:Havells/Wipro/Phillips/Bajaj/CG/C&S.

Supply and fixing of ceiling rose, surface bakelite, 65x50mm, two to three terminals along with back plates complete all as specified and as directed. Make: SSK/Anchor/Fine/Cona

Supply and fixing of lamp holder, insulated body, with back plate for angular batten fittings with one PVC block of size 75mm x 75mm suitable for mounting fittings complete all as specified and as directed. Make: Anchor/Fine/SSK/Cona

Supply and fixing of MCB SP, 6 to 32 Amps, 240 volt, 10 KA, 'C' curve, ISI marked, including taking down existing old unserviceable MCB of any capacity and condition and removing from site complete all as specified and directed. Make: Siemens Betaguard/ Schneider Acti 9/Hager Nevello Plus/Legrand Ekinox/L&T Exora/ABB Elegance.

Supply and fixing of MCB SPN, 40 Amps, 240 volt, 50 Hz, 'C' curve, ISI marked, including taking down existing old unserviceable MCB of any capacity and condition and removing from site complete all as specified and directed. Make: Siemens Betaguard/ Schneider Acti 9/Hager Nevello Plus/Legrand Ekinox/L&T Exora/ABB Elegance.

Supply and fixing of indoor decorative surface mounting LED tube light fitting, batten type, with poal diffuser, high efficient aluminium housing body in CRCA body suitable for LED tube, high efficient, AC 220-240 volts, 50 Hz with and including 18/20 watt LED tube rod luminaries (warm/cool as per site requirement), environment friendly, energy saving, high efficient PMMA diffuser, T8 with aluminium extrusion, heat sink and connecting with copper conductor flexible cable of size 0.50 Sqmm from ceiling rose to connector of the light fitting including disconnecting and taking down of existing old unserviceable light fitting and removal from site complete all as specified and directed. Make: Havells/Wipro/Philips/Jaquar/C&S/Bajaj.

Supply and fixing of sheet metal enclosures for distribution board for MCCB's, Vertical, double door, powder coated, IP-43 type, 4 ways, MCCB +12 module suitable for and including MCCB, Four pole, 125 Amps as incomer and MCB's as out going, made up of 2mm thick MS sheet of suitable size and making all type of connections with suitable size of gland for incomer LT cable complete, concealed on the wall surface and making good the disturbed portion with adjoining surfaces to match with existing finishes and dismantling and taking down the existing DB's of any type complete all as specified and as directed. Note: For electric connection of MCCB 4 pole suitable rating thimble/lugs should be used. Make:-Siemens Betagaurd/Schenider Acti 9/Hager Nevello Plus/Legrand Ekinox/L&T Exora/ABB Elegance

Supply and fixing of sheet metal MCB DBs, 8 way with 200 Amps rated bus bar, single pole and neutral, with transperent acrylic double door, IP-43, fixed on wall, duly grouted in solid block wall or on wooden board with and including copper lugs/thimbles duly crimped for connection including taking down existing old unserviceable MCB DB and removing from site complete all as specified and directed. Make: Siemens Betaguard/ Schneider Acti 9/Hager Nevello Plus/Legrand Ekinox/L&T Exora/ABB Elegance.

Supply and fixing of LED security new generation energy saving and eco friendly, long life, light luminaire 25 watt, made up of versatile die cast aluminum housing with black epoxy powder coating with cover heat resistant glass, safety input voltage range 170 to 270 Volts, IP66 protection, including service brackets of GI pipe 32mm bore, medium grade, of length 0.90 metre with MS clamps, bolts, nuts and washers and suitable reducer for connecting to GI pipe as required at site and making all required electrical connections using suitable cable including disconnecting and taking down old unserviceable existing light fitting and removal from site complete all as specified and as directed. Make: Havells/Wipro/Philips/Jaquar/C&S/Bajaj.

Taking out old unserviceable earthing and material and labour for new earthing complete with galvanised earth plate electrode 600mm x 600mmx 6mm thick surrounded by charcoal and salt, buried directly in ground vertically in a pit of depth not less than 2.25m below ground level with top edge of the earth plate not less than 1.5m below normal ground level, connected to 4.00 mm GI wire earth lead by means of bolts, nuts, checks nut and washers made out of galvanized iron or steel, earth wire protected by galvanized steel pipe 15mm dia (medium grade) and connected to main switch or main control board all as shown in Electrical Plate No.3 of SSR Part-I & including necessary excavation and earth work in any type of strata, PCC (1:3:6) type C2 in pit, RCC cover slab 50mm thick in 1:2:4 type B-1 using 8mm dia TMT bars @10cm c/c both way with one 8mm dia bar as handle for lifting, 20mm dia GI medium grade watering pipe, funnel, wire mesh, charcoal or coke & salt in alternate layers, etc.all as indicated including taking down old unserviceable existing earthing and removal from site and testing on completion complete all as specified and directed.

Taking down ceiling or wall fan, sealing cable end, dismantling blades and removing fan and spray painting complete fan including filling cavities with filler with two coats of white duco paint after cleaning all dust, writing MES No with black colour permanent marker etc. complete all as specified and directed.

Mateial and labour for hanging only ceiling/wall fan and connecting up using new three core flexible cable 23/ 0.0076 size from ceiling rose to connector of fan complete all as specified and directed.

Supply and laying of cable, XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty), 1100 volts grade, with stranded aluminium conductor of size 4 core, 16 Sqmm and laying in trenches including disconnecting and taking down of old unserviceable existing cable and removal from site complete all as specified and as directed. Make of cable: Gloster/Finolex/Havells/Polycab

Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre in depth and getting out in soft/loose soil for laying of cable complete all as specified and as directed.

Returning filling in, in soil, including spreading leveling watering and well ramming in layers not exceeding 25 cm each complete all as specified and as directed.

Removing excavated spoil/materials to a distance not exceeding 50 metre and depositing where directed at level not exceeding 1.5 above the starting point complete all as specified and as directed.

Material and labour for fine and dry sand, cushioning for underground cable, by providing a layers of sand 8cm deep before laying and 15cm deep after laying the cable including stretching the cable and punning sand cushioning complete all as specified and as directed. Note - Punned thickness of sand layer shall only be measured and paid to contractor.

Supply and laying un-reinforced, precast concrete cable cover, class LV, type 1, Flat, with peak, size 250 mm x150 mm x40 mm complete all as specified and as directed.

Supply and fixing of light grade, GI tubing, of size 40mm dia, for cable protection and fixed with clamp to pole and wall with nuts and bolts complete all as specified and as directed. Make of GI pipe: Jindal/Tata/Zenith/Oswal/Prakash

Supply and laying of sub main wiring with two runs of 6 Sqmm single core PVC insulated but unsheathed multstranded copper conductor FRLS-H, 1100 Volts grade cable with one run of 6 Sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS-H, 1100 volts grade cable as earth conductor, drawn through and including casing and capping or PVC concealed conduit, in ceiling or wall, heavy duty grade, ISI marked, not less than 25 mm dia (external) with wall thickness not less than 1.8 mm with conduit accessories and taking down and removing from site existing old unserviceable burnt sub main wiring of any size and in any condition complete all as specified and directed. Note: (i) All runs of cable and one run of conduit shall be measured and paid as one metre length of unit. (ii) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. Make of wire:-Finolex/Polycab/Havells/RR Kabel/Grandlay/L&T Make of PVC Conduit:-Finolex/Polycab/Kalinga Premium/Surya/Plaza/Diplast

Material and labour for earthing pit display boards, made out of 3mm thick MS sheet of size 30 x 35cm welded to 75cm long 25 x 25 x 3 mm thick MS angle iron, grouted in PCC 1:3:6 type C1 (with 20mm graded stone aggregate) to a depth of 20 cm and applying two coats of synthetic enamel paint of approved color over a coat of red oxide primer and writing the letters on plate for showing the following details: 1. EARTHING PIT NO. : 2. DATE OF MEASUREMENT : 3. NEXT DUE DATE : 4. STANDARD VALUE : 5. VALUE OBTAINED : 6. MEASURED BY : 7. SUPERVISED BY :

Note:- Amount of credit of Rs. 1,26,264.00 for retrieved materials is mentioned in Schedule of Credit Page Nos. 79R & 80R of tender documents in pdf form which will be deducted offline while acceptance of tender.

bhagwandasswazirchand

MAYANK ENTERPRISES

Karishan Kumar goel