Executive Engineer Circle-I works Division

Supply and delivery of 20 HP, 3Phase, 440 Volts, 50 Hz and 2900 RPM Monoblock Centrifugal pump set of 100mm x 75mm size with a discharge of 32.9-21.1 LPS against 40-54 mts head complete as directed by departmental officer incharge of the work Model- TMH 54M, Make:Texmo (as approved by Engineering incharge) excluding GST

Supply & Fixing of Star-Delta Starter 415V, 3 phase, 50Hz.. enclosed with no volt coil, overload protection and single phase preventor , etc., complete suitable for Makes: L&T (MUG20)

Fabrication, errection, commissioning, testing and trail run of above pump sets, panel board and Sluice valves & Non return valves and laying & fixing of service wire & moter connections and 1 No Earthing with required section and delivery M.S Reducer, M.S Bends, M.S Tees, M.S pipe line laying gas cutting and welding bolt & nuts rubber packing, PVC conduit for wires,clamps, lugs and air release provision and painting and transportation charges complete as directed by departmental authorities

Earth work at booster pump house, c.c bed concreate, hole cutting for suitable size including material cost and labor charges and transportation charges etc., complete as directed by departmental authorities.

Supply and delivery of "Resilient Seated Soft Sealing" Gate Valves (Sluice Valves) with Body and Bonnet of Ductile Iron GGG-40/SG-400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, Replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The Valves should be Vacuum tight and 100% leak proof with face to face dimensions as BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN-3202F4/BS:5163 Type A Flange drilling as per IS - 1538 excluding all taxes, duties and transportation. including cost and onveyance of all required materials etc., complete as directed by departmental autorities SOR 2025-26,

100mm dia PN.1.6 MAT-08069

150mm dia PN.1.6 MAT-08070

Manufacture, Supply and delivery of DI D/F Tilting disc Swing Check Valves Slanted seated with maximum swing of 59 degree with metallic, corrosion proof and wear resistant seat faces, Body and Disc of ductile cast iron GGG-40/SG-400/15 or GGG- 50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 Shafts of stainless steel, shaft bearing of zinc free bronze and Integral body seat face & disc face with nickel- chromium overlay welding and micro finished. All the inside and outside of the body is to be coated with double coating of food grade epoxy liquid lacquer (EP-F) with minimum thickness of 150 microns, color: RAL 5005 Blue face to face dimensions according to EN 558-1/14/DIN 3202-F4, Flange dimensions according to EN1092-2/IS 1538 including cost and onveyance of all required materials and transportation charges etc., complete as directed by departmental autorities SOR 2025-26,

100mm dia PN.1.6 MAT- 08124

Supply of 3 Core 6 sq.mm. Flat Copper cable of ISI for Submersible Motors confirming to IS:694:1990. Makes: Finolex / RR Kabel/ Polycab / Havells / KEI/ Gloster/ Goldmedal / GM/Finecab/ Million/APAR(Anushakthi)/Sudhakar/ Lauritz Knudsen (formerlyL&T) SOR 2025-26, MAT- 02797

Supply of 126/0.4mm (16.0 Sqmm) FRLS / HFFR / ZHFR PVC insulated 1100V grade as per IS : 694 / 1990 specification for Copper cable. Makes: Finolex / RR kabel / Havells/Finecab/ KEI/ Polycab/ Gloster /Goldmedal/GM/ Fortune Arrt/Anchor/Million/ APAR (Anushakthi) /Sudhakar /Orbit/Batra Henlay SOR 2025-26, MAT-02754

Supply of ………., Adjustable, Confirms to IEC 60947-2 and IS 13947-Part 1&2 having Breaking Capacity ………. with thermal magnetic release Panel Mounted Makes: L&T- D shine / Schneider-CVS/Legrand –(DP X3/DRX)/ Siemens- 3VL / Hager-h3/C&S -Winbreak/HPL-Techno, SOR 2025-26,

125A 3 Pole MCCB,25 KA MAT- 02955

Supply and delivery of peeta board of size 18" x 30" including cost and conveyance of all materials etc., complete as directed by the departmental authorities. SOR-2025-26, MAT-02741

Manufacturing, Supply, Delivery and fixing of required M.S. fabricated pipe and specials ( Bends, Tees, and Reducers etc) using MS sheet and providing red oxide paint and anticorrosion paint two coats including cost all materials with all taxes, conveyance to work spot and all labour charges etc, complete as per the instructions of the departmental authorities as per SS

Cost of MS Flanges including cost of bolts, nuts, rubber packing etc., complete and flange thickness confirming to IS 7322-1985 and flange dimensions confirming to IS 1538-1993 excluding cost of MS specials including cost and conveyance to site, vat etc., complete as per SOR 2025-26

100 mm dia. x 15 mm thick MAT-06411

150 mm dia. x 15 mm thick MAT-06413