CA NO GE(N)AMB-34/2023-24 SPECIAL REPAIR TO BLOCK NO. 258/1-9 IN RACE COURSE COLONY AND PROVISION OF TOILET AND BATHROOM BLOCK FOR OR ACCN IN THE AREA OF AGE B/R-I UNDER GE (N) AMBALA CANTT

Amount

Schedule 'A' Part-I (B/R itmes) Taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed by the Engineer-in-Charge.

M & L rendering 15 mm thick on brick work or concrete wall surfaces in cement mortar 1:4 including mixing water proofing compound @ 2% by weight of cement or as per manufacturer's instruction and finished fair and even without using extra cement complete all as specified and as directed by the Engineer-in-Charge. (WPC shall be measured and paid for separately)

Material and labour rendering 10 mm thick on any faces of brick work or concrete wall surfaces in cement mortar 1:6 and finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour rendering 05 mm thick brick work or concrete ceiling surfaces in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Supply only water proofing compound complete all as specified and as directed by the Engineer-in-Charge.

M&L rough cast plaster 15 mm thick in cement motar 1 :4 complete as specified in SSR Part-I, clause 14.22 shall consisting of following:- firstly apply under coat in cement mortar 1:4 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine gravel agg. which is generally of size between 6 to 12 mm depending on texture required mixed with coarse sand and cement in the ratio 1:1:1 shall be applied, complete all as specified and as directed by the Engineer-in-Charge.

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and as directed by the Engr-in-charge.

M&L brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge.

M&L brick work with sub class 'B' old size bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M&L for brick work using old servicable bricks obtained from serial item No 07 above including removing motar, cleaning the bricks with water, etc. straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n exe 15 cm thickness (below or above ground level) complete all as specified and as directed by the Engineer-in-Charge.

M & L 25 mm thick PCC 1:2:4, type B0 as in sub base of floor (using 12.50mm graded crushed stone aggregate), finished even & fair without using extra cement complete all as specified and as directed by the Engr-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing servicable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge.

Material and labour glazed ceramic coloured tiles joint free 1st quality in vertical surfaces/ skirtings/dados of size 450x300x7mm thick/300 x 600 x 7 mm thick or nearest size as required , set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M&L Non Skid coloured ceramic tiles joint free premium/1st quality 7 to 8 mm thick, (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and inculding 15mm thick screed bed in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge.

M&L Non Skid coloured ceramic tiles joint free premium/1st quality 7 to 8 mm thick, (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and inculding 15mm thick screed bed in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge.

M & L machine cut kota stone slab flooring 18 to 22 mm thick of size not less than 550mm x 550mm in floor, set and jointed in neat cement slurry with grey cement mixed with pigment to match the shade of the slab including rubbing and polishing (granite finish) over and including 15 mm thick screed bed in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M & L machine cut kota stone slab flooring 18 to 22 mm thick ( kota stone shall be cut from size not less than 550mm x 550mm) in skirting , set and jointed in neat cement slurry with grey cement mixed with pigment to match the shade of the slab including rubbing and polishing (granite finish) over and including 10 mm thick rendering in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M & L 16 to 18 mm thick Jet black granite work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick rendering in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Demolition of un-reinforced cement concrete of any description and in any position not otherwise specificaly provided for complete all as specified and as directed by the Engineer-in-Charge.

M & L providing 75 mm thick cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregates as in plinth protection laid in alternate bays (not exc 2 Sqm each ) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight including form work complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkats or frames with shutter area not exceeding 1.50 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed by the Engr-in-charge.

Taking down chowkats or frames with shutter area exceeding 1.50 Square meter and not exceeding 4.00 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed by the Engr-in-charge.

M&L rolled mild steel framed work as in chowkats of door or gates of angle or other section with gusset plates, rails braces etc. complete. drilled for fixing for steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and including either hooks and hinges and hanging ,door fitting (exclusive of steel sheeting or other covering, running rails and guides) also fastening and fixing conforming to Fe-410-W (Grade E-250) quality 'A' complete all as specified and as directed by the Engineer-in-Charge.

S & F flush shutters 35 mm thick, solid core construction, with block board core and ply wood face panels, commercial type on both sides complete all as specified and as directed by the Engr-in-charge.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube fixed in opening complete all as specified and as directed by the Engineer-in-Charge.

S&F factory made solid PVC moulded door shutters with partical board core 28 to 30 mm thick (styles) with 2, 4, or 6 raised panel design with 2 mm thick plain moulded PVC sheet on the front face and 2mm thick plain colour PVC sheet on back face fixing in frame at site as per specification and drawing complete all as specified and as directed by the Engineer-in-Charge.

S&F double shutter steel window box type ERW hollow P section comprising of glazed/gauged skeleton shutter fabricated from following sections :- (a) ERW hollow P section frame of size 60 mm x25 mm made from 1.25 mm thick MS sheet (02 Nos i.e. 01 for glazed shutter and 01 for gauzed shutter ). Both P section shall be welded with flat iron 25x03 mm thick all around of frame on both inner and outer faces . (b) Style and rails of window shutters shall be fabricated with ERW hollow P section of size 50 mm x25 mm made from 1.00 mm thick MS sheet and comprising of 02 Nos sash bars for glazed window leaf of T – section 20 x 03 mm thick and one No sash bar of 20 mm x 3 mm thick section for gauzed winodw leaf . (c) Vertical mullion shall be ERW hollow T -section of size 60 x 25 mm made from 1.25 mm thick MS sheet (d) The above steel window shall be deemed to include the following accessories/ fittings : i) Hold fast 150mm long mild steel flat iron 12x3 mm thick made to shape- 04 Nos per window ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. iii) MS tower bolt stove enamelled 150mm long- 2 Nos per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 No per leaf. (v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 No per leaf

item No. 28 (contd....) vi) Pintal hinges 12 x 75 mm - 2 Nos each leaf vii) 10mm square Guard bar @ 10 cm c/c welded to frame . (viii) Two coat of Synthetic enamel paint over one coat of red oxide primer. (ix) 0.36mm nominal dia of stainless steel wire mesh and average width of aperture of 1.40mm fixed in gauzed skelton shutter of window with flat iron 15 x 03 mm with steel screws . (x) 3mm thick sheet glass, ordinary quality and with oil putty in square n. exc 0.5 sqm in each pane fixed in glass shutter of window. (xi) Fabrication and fixing arrangements as per specification including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed. Notes : (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery, grill and other accessoriries as mentioned above. (iii) The window upto 1.00 metre width shall consists of two leaves both for gauzed shutter and glazed shutter and all the shutters are openable. The window more than 1.00 metre width shall have two openable leaves on both outer side for gauzed shutter and glazed shutter and middle leaf/shutter shall be fixed type.

S&F box type using ERW hollow 'P' section of size 60 x 25mm made from 1.25 mm thick MS sheet ventilators fixed type with glazing bar including MS grills of square bar 10mm dia @ 100 c/c complete with glazing bars dovetailed or welded, including two coat of synthetic enamel ordinary tint paint over a coat of red oxide primer complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing factory made 35 mm thick 2nd class hard wood glazed and skeleton shutters,open rebated and prepared to receive glass , gauze etc. (without sash bars) ,edges of framing plain chamfered or rounded , fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I, Section-8, clause 8.24 (a) (wood shall be kiln seasoned and chemically pressure treated) complete all as specified and as directed by the Engineer-in-Charge.

S&F mild steel door shutter two leaves with frame of 20 gauge MS sheet (all around) and leaves of 21 gauge MS Sheet ( all as per Godraj Pettern) with three way locking arrangement with brass lock with duplicate key and CP handle including two coats of spray painting over a coat or red oxide primer complete fixed in existing cupboard with necessary nuts, bolts including embedded in PCC 1:2:4 (area of opening shall be measured) complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing galvanised mild steel wire cloths 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tack or galvanised wire staple complete all as specified and as directed by the Engineer-in-Charge.

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F 150 mm long aluminium handle cast type anodised complete all as specified and as directed by the Engineer-in-Charge.

M & L sheet glass 3.00mm thick ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 250mm long aluminum alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloys to door shutter complete all as specified and as directed by the Engineer-in-Charge.

S&F mild steel 150 mm ordinary rat tail rod pattern springs including roller and roller plate etc complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing stainless steel butt hinges 100 mm long medium weight complete all as specified and as directed by the Engineer-in-Charge.

M&L 2nd class hard wood Small fitting such a brackets of any type ,latch and hinge block , shaped door and window stops and the like including all necessary labours articles n. exc200 Cu cm each inlcuding 50mm long stainless steel butt hinges complete all as specified and as directed by the Engineer-in-Charge.

S & F as in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge.

M & L galvanised iron tubing 15mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge.

M & L galvanised iron tubing 20 mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

Cutting chases to brick wall built in cement mortar, pinning in making good to facing where required and pointing in CM 1:3 to edges of landing , steps , cills , sunshades, shelves , lintel etc. and cutting chases for concealed water tubing etc and making good cutting not exc 10 cm girth complete all as specified and as directed by the Engineer-in-Charge.

Unscrewing and taking down old unserviceable stop valve, bib tap, pillar tap and shower rose of any size/description and removal from site complete all as specified and as directed by the Engineer-in-Charge.

S & F 15mm bore cast copper alloy chromium plated angular stop cock with capstan head, screwed down, high pressure scrwed both ends for iron pipe or for unions complete all as specified and as directed by the Engineer-in-Charge.

S & F 15mm bore cast copper alloy chromium plated fancy type stop valves with capstan head, screwed down, high pressure scrwed both ends for iron pipe or for unions complete all as specified and as directed by the Engineer-in-Charge.

S & F 20mm bore cast copper alloy chromium plated fancy type stop valves with capstan head, screwed down, high pressure scrwed both ends for iron pipe or for unions complete all as specified and as directed by the Engineer-in-Charge.

S & F 15mm bore cast copper alloy fancy type chromium plated stop valves with long shank and cup (concealed type), screwed down, high pressure with capstan head, scrwed both ends for iron pipe or for unions complete all as specified and as directed by the Engineer-in-Charge.

S&F bib taps 15mm bore fancy type brass chromium plated with long body, wall flanges and capstan head, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair, brass chromium plated basin mixer sawn neck for mixing hot & cold water for 15mm bore pipes including all connecting fittings, screwed down for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F brass chromium plated shower rose 100mm size round/ square type swivel type with arm of standard size as per site complete all as specified and as direced by the Engineer-in-charge.

Unscrewing and taking down old unserviceable PVC connection of any size/description and removal from site complete all as specified and as directed by the Engineer-in-Charge.

S & F PVC connections 15 mm size with PTMT nuts of length 450 mm as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F vitreous china squatting pan, Orissa pattern, of size 580 mm x 440 mm white with integral foot rest & PVC SWR 'P' or 'S' trap of pressure rating 6 Kg per square cm complete including provn of cement concrete bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe complete all as specified and as directed by the Engineer-in-Charge.

Taking down old unserviceable flushing cistern of any size/description and removal from site complete all as specified and as directed by the Engineer-in-Charge.

S & F 10 ltr PVC valveless syphonic action type flushing cistern with brackets, flush pipe etc complete including inlet ball valve float and handle including brackets, of approved make including all connections & flush pipes for WC complete all as specified and as directed by the Engineer-in-Charge.

S & F vitreous china wash hand basin white, flat back of size 550mmx400mm with pedestal fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of waste fitting etc as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F as in repair PVC cabinet box type looking mirror of size 450mm x 600mm and fixed with stainless steel screw complete all as specified and as directed by the Engineer-in-Charge.

Dismantling water tanks of capacity exc. 250 ltr and not exc. 500 ltrs and removing from site complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing water storage tank, 500 ltr capacity, HDPE triple layer, white colour, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm dia high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore, complete all as specified and as directed by the Engineer-in-Charge.

S & F 110mm bore PVC (SWR) branch pieces, double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and as directed by the Engineer-in-Charge

M & L 75mm bore PVC (SWR) floor trap, plain with stainless steel grating with or without waste hole including jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement, complete, all as specified and as directed by the Engineer-in-Charge.

M&L preparation of newly plastered/ unplastered surfaces of walls and applying two coats of oil bound distemper with painting roller over a coat of alkali resistant primer over and inlcuding 1mm to 2mm thick wall care putty white cement based in two or more coats to achive smooth surface complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of newly plastered surfaces of wall and applying two coats of cement based paint complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of new plastered/ unplastered surfaces of brick/concrete ceiling and applying three coats of white lime wash complete all as specified and as directed by the Engineer-in-Charge.

M & L complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means, wasing down with water to remove loose particles etc and applying two coats of oil bound distemper with painting roller over a coat of alkali resistant primer over and inlcuding 1mm to 2mm thick wall care putty white cement based in two or more coats to achive smooth surface complete all as specified and as directed by the Engineer-in-Charge.

M & L complete removal of existing treatment on ceiling surfaces (any number of layers) by scrapping with steel scrappers or any other means, wasing down with water to remove loose particles etc and applying two coats of white lime wash complete all as specified and as directed by the Engineer-in-Charge.

M & L complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means, wasing down with water to remove loose particles etc and applying two coats of cement base paint complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of new steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by the Engineer-in-Charge.

S & F stainless steel curtain rod 25mm dia having wall thickness 1.00mm with and including stainless steel decorative brackets, two lotto for each rod length at both end etc fixed with stainless steel screws as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F as in repair kitchen plate rack of stainless steel sheet 1mm thickness size 750mm x 600mm x250mm and having weight not less than 5.00 Kg each complete all as specified and as directed by the Engineer-in-Charge.

S & F sinks with drainage board made out of stainless steel 1mm thick sheet for kitchen or laboratory with plugs, waste pipe, brass chromium plated coupling and wastes; in-cluding bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connect-ing union to pipe overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm as in repair complete all as specified and as directed by the Engineer-in-Charge.

Dismantling Brick tiles or terracing tiles, single layer on roofs complete all as specified and as directed by the Engineer-in-Charge.

Demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and as directed by the Engineer-in-Charge.

M & L providing cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in roof kerbs, mud stops, padding and finished even and smooth without using extra cement including form work where ever required complete all as specified and as directed by the Engineer-in-Charge.

Material & Labour for providing and laying 3mm thick APP (atactic polypropylene polymer) modified prefabricated five layer weight not less than 3.60 kg /Sqm water proofing membrane black finish reinforced with non woven polyster matt and consisting of a coat bitumious primer @ 0.40 ltr /Sqm by the same membrane manufactures of density 0.87 to 0.89 kg/ltr at 25 degree centegrate temprature and viscosity 70-160 cps over the primer coat with overlap of 100mm at the side and 150mm at the end, the layer membrane shall be laid using butane gas torch and sealing all joints etc after preparing the surface complete as per standred practice as per manufacture's instructions . The vital physical and chemical parameters of the membrane shall be under ;- (i) Joint strength in longitudinal and transverse direction at 23 degree centegrate at 650/ 450 N /5 cms (ii) Tear strength in longitudinal and transverse direction at 300/250N/5 cms. Softing point of membrane not less then 150 degree centegrate when tested in accordance with ASTM (d-5147) (iii) The laying of membrane shall be got down through the authorised applicator of manufactures of membrane only complete all as specified and as directed by the Engineer-in-Charge.

M & L cement concrete tiles 30 cm x 30cm x 20 mm thick, machine pressed laid on screed bed and joints grouted flush in CM (1:3) mixed with 5% crude oil by weight of cement including screed bed 15 mm thick in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge.

Demolition of reinforced cement concrete in roofs, floors, beams, chajjas, staircases, landings and similar suspended work (reinforcement cut as required to facilitate demolition) complete all as specified and as directed by the Engineer-in-Charge.

Formwork to chajjas, shelves and the like including edges for rough finished surfaces of concrete flats complete all as specified and as directed by the Engineer-in-Charge

M&L TMT steel bars 10mm dia and over cut to length, bent to shape reqd incl cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia complete all as specified and as directed by the Engineer-in-Charge.

M&L TMT steel bars 6 to 8mm dia cut to length, bent to shape reqd incl cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia complete all as specified and as directed by the Engineer-in-Charge.

M&L TMT steel bars 5mm dia and over up to and including 10mm dia in stirrups, spacers etc, cut to length, bent to shape reqd incl cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia complete all as specified and as directed by the Engineer-in-Charge.

M & L RCC M-25 (design mix) using 20mm graded crushed stone aggregates as in chajjas and the like complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of boarding any description fixed in any position with nails complete all as specified and as directed by the Engineer-in-Charge.

M&L 18 mm thick prelaminated MDF board one side plain and other side decorative choice exterier grade (grade-1) confirming IS 14587, fixed with screws for kitchen cupboard and cabinet , shelves for cupboard, frame with door if required including 3mm thick 2nd class hardwood leeping patti on cut edge of boards complete all as specified and as directed by the Engineer-in-Charge.

S & F continuous (paino) hinges , width of flaps 30mm (when open) mild steel bright finish or electro galvanished complete all as specified and as directed by the Engr-in-charge.

S&F 100 mm long brass handle fancy type and polished complete all as specified and as directed by the Engineer-in-Charge.

M & L PCC 1:4:8 Type D2 using 40mm graded crushed stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed by the Engineer-in-Charge.

Supply and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage complete all as specified and as directed by the Engineer-in-Charge.

M&L vibratory rubber moulded coloured precast concrete interlocking paver block, any shape and size conforming to IS 15658-2006, ISI marked of 60 mm thickness, grade M-35 with grey cement and pigments over and including 30 mm thick sand cushioning complete all as specified and as directed by the Engineer-in-Charge.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified & directed by the Engr-in-Charge.

S & F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in treches or in floors with clamps complete all as specified and as directed by the Engineer-in-Charge

S & F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with clamps complete all as specified and as directed by the Engineer-in-Charge

S&F 75mm PVC (SWR) bends of any radius, with access door complete all as specified and as directed by the Engineer-in-Charge.

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in treches or in floor complete all as specified and as directed by the Engineer-in-Charge

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with clamps complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing 75 mm bore PVC (SWR), vent cowls including jointing with solvent cement, complete all as specified and as directed by the Engineer-in-Charge.

S&F 110mm PVC (SWR) bends of any radius with access door, complete all as specified and as directed by the Engineer-in-Charge.

S & F soap dish, brass chromium plated, approximate size 160x160x90mm, fixed to plugs with chromium plated brass screws complete all as specified and as directed by the Engineer-in-Charge

Cutting into existing manholes for connecting new drains, and making good to pipe and rendering, cutting out existing benching for and forming branch channel( 1/2 round or 3/4 section ) in cement concrete 1:2:4 type B-1 (using 20mm size crushed stone aggregate) smooth finished and reforming benching as required of pipe 110 mm dia, complete all as specified and as directed by the Engineer-in-Charge.

S & F mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe 290 Gde-E-165 complete all as specified and as directed by the Engineer-in-Charge.

M&L PCC 1:5:10 type E-2, using 40 mm graded crushed stone aggregate as in filling in sunken floor, rounded or chamfered on edges complete all as specified.as directed by the Engineer-in-Charge.

M&L providing sunken floor water proofing treatment comprising of the following :- (a) Scrapping the surface with wire brush and cleaning with water and allow to dry. (b) Applying cement slurry @ 1.2 kg/sqm duly mixed with water proofing compound @ 2% by weight of cement or as per manufacturer's instructions. (c) 15 mm thick cement plaster in CM 1:3 mixed with water proofing compound @ 2% by weight of cement or as per manufacturer instruction ( the corners will be made round in concave shape) and finished even and fair without using extra cement. (d) Applying cement slurry @ 1.2 kg/sqm duly mixed with water proofing compound @ 2% by weight of cement or as per manufacturer's instruction. (e) Applying one coat of hot blown bitumen grade 85/25 confirming to IS-702 @1.20kg/sqm (f) Providing and laying 3mm thick APP (atactic polypropylene polymer) modified prefabricated five layer weight not less than 3.60 kg /Sqm water proofing membrane black finish reinforced with non woven polyster matt using butane gas torch and ceiling all joints. (g) Applying one coat of hot blown bitumen grade 85/25 confirming to IS-702 @1.20kg/sqm.

M & L 40mm dia GI pipe medium grade as in spout complete all as specified and as directed by the Engineer-in-Charge.

Surface excavation (not exceeding 30cm deep) and averaging 15 cm deep, getting out in soft/loose soil complete all as specified and as directed by the Engineer-in-Charge.

Excavation in trenches, not exc 1.5 m wide and not exc 1.5 m in depth for foundation etc or for shafts, wells, manholes etc. not exc 10 sqm on plan and not exc 1.5 m in depth and getting out in soft/ loose soil complete all as specified and as directed by the Engineer-in-Charge.

Returning, filling in, including spreading, levlling ,watering and well ramming in layers not exceeding 25cm thick complete all as specified and as directed by the Engineer-in-Charge.

Removing surplus excavated material to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

M & L reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed by the Engineer-in-Charge.

M&L reinforced cement concrete M-25 (Design Mix) using 20mm graded crushed stone aggregate as in pillars, posts,struts, piers, columns and stanchions complete all as specified and as directed by the Engineer-in-Charge.

M&L reinforced cement concrete M-25 (design Mix) using 20mm graded crushed stone aggregate in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed by the Engineer-in-Charge.

M & L RCC M-25 (design mix) using 20mm graded crushed stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by the Engineer-in-Charge.

M&L formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter flat rough finished surfaces of concrete complete all as specified and as directed by the Engineer-in-Charge.

Formwork to sides of pillars, posts,struts, piers, columns and stanchions flat rough finished surfaces of concrete complete all as specified and as directed by the Engineer-in-Charge.

M & L formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports overhangs etc, also splays between floors and beams, etc., work in rough finished flat surfaces of concrete complete all as specified and as directed by the Engineer-in-Charge.

Formwork to soffits of suspended slabs such roof slab, floor slabs, landings and similar work not exceeding 20 CM thick (horizontal or sloping) flat for rough finished surfaces of concrete , complete all as specified and as directed by the Engineer-in-Charge.

M & L formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide, for roughed finished surface of concrete complete all as specified and as directed by the Engineer-in-Charge

M & L 100 mm thick PCC 1:4:8 Type D-2 using 40mm graded crushed stone aggregate as in sub base of floor/ hard standing etc and finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

S & F counter top vitreous china wash hand basin white of size 515mmx365mmx120mm, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of waste fitting etc complete all as specified and as directed by the Engineer-in-Charge.

S&F magnet catcher fixed in cabnet shutter (one portion) and wooden frame (other portion) with screw complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 110 mm bore PVC (SWR), vent cowls including jointing with solvent cement, complete all as specified and as directed by the Engineer-in-Charge.

S & F 150mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in treches or in floor complete all as specified and as directed by the Engineer-in-Charge

M & L providing PCC precast 1:2:4 type B1 using 20mm graded crushed stone aggregate as in landings, precast cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including chamfers, weathering, throating etc and setting CM 1:4 complete with joints to match, complete all as specified and as directed by the Engineer-in-Charge.

S & F stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore pipe complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing water storage tank, 1000 ltr capacity, HDPE triple layer, white colour, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm dia high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore, complete all as specified and as directed.

M & L providing cement concrete 1:2:4 Type B1 using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed by the Engineer-in-Charge.

M & L concrete bed to drain pipes of 150mm bore, including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing vitreous china urinal, half stall type white (excluding flushing cistern, flush pipe) but including brass chromium plated spreader, PVC waste pipe , providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, grating and union for discharge pipe. (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and as directed by the Engineer-in-Charge.

Supply & fixing sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide and 60cm long with chromium plated guard and railing ,complete all as specified and as directed by the Engineer-in-Charge.

S & F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed by the Engineer-in-Charge.

M & L PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate as in holdfasts complete all as specified and as directed by the Engineer-in-Charge.

S & F 20 mm bore Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

M & L mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders,walk ways, railings conforming to Fe.290.Gde-E-165 complete all as specified and as directed by the Engineer-in-Charge.

M & L frosted sheet glass 3.00mm thick ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and as directed by the Engineer-in-Charge.

S&F stainless steel fancy type peg set ( each peg having 5 Nos hook) and fixed with stainless steel screws and PVC rawel plug complete all as specified and as directed by the Engineer-in-Charge.

M & L applying a coat of solar reflective aluminium paint @ 0.11 kg per sqm on APP membrane surfaces complete all as specified and as directed by the Engineer-in-Charge.

Dismantling structural steel work including doors, gates, grills and stiffner for securing chain link fencing including nuts, bolts etc but excluding framed trusses etc complete all as specified and as directed by the Engineer-in-Charge.

Removing old tar felt, all loose dirt, cement plaster, cleaning the concrete surface including removal & cleaning of vegetation, fungus,moss small trees etc from the roof top with wire brush and washing the roof surface with water to remove all dirt, dust, mud etc complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete in existing sunken floor etc and removal of the same to a distance exceeding 250 mtr and not exceeding 500 mtr, depostied where directed complete all as specified and as directed by the Engineer-in-Charge.

S&F as in repair brass chromium plated wall mixer for mixing hot & cold water for 15mm bore pipes including all connecting fittings, screwed down for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge.

Schedule 'A' Part-II (E/M itmes) Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder, regulators, socket outlet, etc and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and as directed by the Engineer-in-Charge.

Disconnecting electrical connection, taking down ceiling fans of any sweep of any make with down rods, blades canopy etc kept in safe cousdy of contractor 's store till completion of civil works and after completion of civil works cleaning the fan motor assembly body, blade of ceiling, filling the cavity, rubbing with sand paper, taking off old paint with the help of chemicals & painting the ceiling fan with one coat of superior quality synthetic enamel paint including writing the MES number on the ceiling fans with synthetic enamel paint, reassembling the ceiling fan and refixing on the same loction, making electrical connection with 3 core copper condctor flexible cable of size 1.5sqm, testing complete all as specified and as directed by the Engr-in-charge.

Disconnecting electrical connection, taking down single/ three phase electric meter, kept in safe cousdy of contractor 's store till completion of civil works and after completion of civil works cleaning the electric meter and refixing on the same loction, making electrical connection, testing complete all as specified and as directed by the Engr-in-charge.

Disconnecting electrical connection, taking down MCB DB TPN/SPN, kept in safe cousdy of contractor 's store till completion of civil works and after completion of civil works cleaning the MCB DB and refixing on the same loction, making electrical connection, testing complete all as specified and as directed by the Engr-in-charge.

Disconnecting electrical connection, taking down MCBs of any size and type, kept in safe cousdy of contractor 's store till completion of civil works and after completion of civil works cleaning the MCBs and refixing on the same loction, making electrical connection, testing complete all as specified and as directed by the Engr-in-charge.

Taking down old unserviceable earthing of any type and removing the unserviceable materials from site complete all as specified and as directed by the Engineer-in-Charg

Material and labour for point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall/ceiling surfaces and incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes modular type of size/modules as required at site with earth dolly (boxes shall be galvanised or painted with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally) including provision of new covered plate over sunken box for housing the modular switches , modular socket outlets,modular fan regulators etc. for one light/fan/exhaust fan point controlled by one way switch, complete all as specified and as directed by Engineer-in-Charge. Note :- a) .All chases will be cut by chase cutter only b) Switch, socket outlet and fan regulators to be measured and paid for separately .

Description same all as per item No. 153 but for One 3 pin 5 Amps socket outlet controlled by one switch on same board, complete all as specified and as directed by Engineer-in-Charge.

Description same all as per item No.153 but for One 3 pin, 5 Amps, socket outlet controlled by one switch on independent board, complete all as specified and as directed by Engineer-in-Charge.

Description same all as per item No.153 but one light point controlled by two way switch complete all as specified and as directed by Engineer-in-Charge.

Description same all as per srl item No 153 here-in-before but for one socket outlet 15 Amp with 2.50 sq mm PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 2.50 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade ISI marked with multi stranded copper wire as earth continuity conductor connected to common earth dolly complete all as specified and as directed by the Engineer-in-Charge.

Description same all as per srl item No 153 here-in-before but for one socket outlet 15 Amp with 4.00 sq mm PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 4.00 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade ISI marked with multi stranded copper wire as earth continuity conductor connected to common earth dolly complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix modular switch 1 module, single pole, one way 6 Amps flush type, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fix modular switch 1 module, single pole, one way 16 Amps flush type, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fix modular switch 1 module, single pole, two way 6 Amps flush type, 230 volts complete all as specified and as directed by Engineer-in-Charge.

S&F modular bell push 6 Amp, 1 way, 1 module, 230 volts complete all as specified and as directed by the Engineer-in-Charge.

Supply & fix modular socket outlet 2/3 pin combined, 6 Amp, one way, two module, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply & fix modular socket outlet 3/3 pin combined, (6pin), 6/16 Amp, one way, two module, 230 volts complete all as specified and as directed by Engineer-in-Charge.

S&F electronic Fan regulator modular 100 watt, 1 module, 230 volts , 50 Hz, AC supply suitable for ceiling fan any type/make/sweep complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix ceiling rose surface type 2/3 terminal polycarbonate, isolated body complete all as specified and as directed by the Engineer-in-Charge.

Supply & fix calling bell ding dong 230 volt including removing unserviceable bell, complete all as specified and as directed by the Engr-in-charge.

Disconnecting electrical connection, taking down old unserviceable indoor tube light fitting/bluk head fitting/security light fittings and removal from site complete all as specified and as directed by the Engr-in-charge.

Supply and fixing indoor decorative LED tube light fitting box type 18/20 watt with electronic driver, opal diffuser, high efficient PVC housing body suitable for LED tube, high efficient, AC 220-240 volts, 50 Hz including 18/20 Watt LED tube rod luminaries environment friendly, high efficient, T8 with aluminium extrusion heat sink and connecting with copper conductor flexible cable from ceiling rose to connector of the light complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing LED surface mounted bulk head luminaries 8-10 watt with min 800 lumen, industrial model, IP 65, aluminium housing, surge protection including driver & LED lamp etc complete with all accessories, connecting with copper conductor flexible cable from ceiling rose to connector of the light complete all as specified and as directed by the Engineer-in-Charge.

S&F mirror light 9/12watt LED wall mounting fixture, one feet , aluminium housing compact & energy efficient epoxy powder coated CRCA light luminaire, connecting with copper conductor flexible cable from ceiling rose to connector of the light complete all as specified and as directed by the Engineer-in-Charge.

S&F 9/12 watt LED light fitting wall mounting fixture (sketch type) including LED lamp compact and energy efficient epoxy powder coated luminaire and connecting with copper conductor flexible cable from ceiling rose to connector of the light complete all as specified and as directed by the Engineer-in-Charge.

S&F LED Bldg Security Light Fittings of capacity 40 -45 watt made up of die cast aluminium housing with black epoxy powder coating with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with IP-65 protection and other connected accessories including electronic driver, service bracket of mild steel pipe 32 mm bore medium grade of length 0.9 mtr with MS clamps, bolts, nuts, and washers and suitable reducer for connecting fitting to MS pipe as required at site and two coats of synthetic enamel paint over one coat of red oxide primer on mild steel work and making electrical connection, complete all as specified and as directed by the Engineer-in-Charge.

S&F single pole and neutral enclosure with a two pin and earth plug and socket 20 Amp complete with and including one single pole MCB.20 Amp, 10 KA, 'B' curve complete all as specified and as directed by the Engr-in-charge.

Supply and fix sheet metal MCB DB SPN 8 way with 200 Amps rated bus bar single pole and neutral with double door IP-54 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection complete all as specified and as directed by the Engr-in-charge.

Supply and fix MCB SP, 6-40 Amps, 240 volt,10 KA , 'B' curve as per site requirement including removing old unserviceable MCB complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix MCB SP, 6-40 Amps, 240 volt,10 KA , 'B' curve as per site requirement complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix MCB SPN, 6 to 32 Amps, 240 volt,10 KA , 'B' curve as per site requirement including removing old unserviceable MCB complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix MCB SPN, 6 to 32 Amps, 240 volt,10 KA , 'B' curve as per site requirement complete all as specified and as directed by the Engineer-in-Charge.

Disconnecting electrical connection, taking down old unserviceable exhaust fan of any size/description and removal from site complete all as specified and as directed by the Engr-in-charge.

Supply and fixing heavy duty exhaust fan 300mm sweep with corrosion resistant metallic body, minimum noise, operation and maintenance free design, totally enclosed, highly efficient, heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings, aerodynamically contoured blades, metallic base frame with rubber mountings for silent operation, maximum watt input not more than 55 watt, 1400 RPM, metal blades and shutter type louvers self-openable/ closeble for protecting the entrance of birds as per IS :2132-1967 and testing complete all as specified and as directed by Engineer-in-Charge.

M & L as in repair sub main wiring with two run of 6 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 6 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked multi stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in PVC conduit medium grade ISI marked of adequate size for housing the wires complete all as specified and as directed by the Engineer-in-Charge. Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. (ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length.

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised earth wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15mm bore(medium grade) and connected to earthing test point as directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm c/c both ways with one handle for lifting made out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing as in repair complete all as directed by Engineer-in-Charge and earth testing on completion .

Supply & Fix Water heater (Geyser) storage type electric of capacity 25 Ltrs , BEE 5 Star rated, ABS body, metal tank with glasss lined coating, multiple heating option, shock safe plug, puf insulation, incoloy glass coated anode rod / copper heating element of capacity 2KW with ISI mark , adjustable knob for temp setting with minimum 8 Bar high working pressure, multi functional safety valve & whirl/Swirl flow technology, thermostat electronic type, thermal cutout capillary type complete including superior quality copper connection pipe heavy duty 15mm dia 450mm long, brass adopter for water connection with nikhel coated ISI marked with fastner, nut bolts, washers duly grouted, giving shape to hole as suitable and plastering including making good of disturbed surface as per existing surface, connecting to inlet and outlet valves, testing complete all as specified and as directed by Engineer-in-Charge.

Supply and laying XLPE insulated, armoured heavy duty electric cable 10 sqmm cross sectional area, 2 core with aluminium conductor, 1100 volts grade complete all as specified and as directed by Engineer-in-Charge.

Excavation in trenches, not exc 1.5 m wide and not exc 1.5 m in depth; for laying of cables, GI pipes and getting out in soft/ loose soil complete all as specified and as directed by Engineer-in-Charge.

S&F light grade GI Tubing of size 32mm dia for cable protection and fixed with clamp to pole and wall with nut, bolts, washers or in trenches complete all as specified and as directed by Engineer-in-Charge

M&L dry sand cushoning to cable i.e 8 cm before laying cable in trenches and 15 cm after laying the cable and compacting complete all as specified and as directed by Engineer-in-Charge. Note: punned thickness shall be measured for payment.

Supply and laying well burnt brick class-B laid flat to cover the cable with width equal to the length of cable and abutting each other for protection of cable complete all as specified and as directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed by Engineer-in-Charge.

Removing excavated material to a distance not exc. 50m and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and as directed by Engineer-in-Charge.

M & L PCC 1:3:6 Type C-2 using 40mm graded crushed stone aggregate as in filing of road cutting / hard standing etc and finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Excavation in trenches, not exc 1.5 m wide and not exc 1.5 m in depth, for laying of cables, GI pipes and getting out in hard/dense soil i.e cutiing existing hard standing/PCC/WBM complete all as specified and as directed by Engineer-in-Charge.

M & L galvanised iron tubing 20 mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in trenches complete all as specified and as directed by the Engineer-in-Charge.

S & F 20 mm bore Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

M & L for cutting/tapping existing pipe GI 40/25 mm bore in postion for insertion of new tee any bore of pipe complete all as specified and as directed by the Engineer-in-Charge.

Note:- Amount of credit of Rs. 1,07,790.00 for retrieved materials is mentioned in Schedule of Credit Page No. 47 (R) to 48 (R) of tender documents in pdf form which will be deducted offline while acceptance of tender.

JS CONSTRUCTION COMPANY

Sawhney Constructions

bhagwandasswazirchand

Durga Enterprises