SPECIAL REPAIR OR MD ACCN BLDG NO P 32 20 CAMP AT THE PRC RAMGARH CANTT UNDER GE RAMGARH

Amount

Taking down complete existing treatment of roof/parapet, mud puska on roof/parapet including plastering, brick tiles, stone slabs and leeping any thickness including removal etc., complete all as specified and as directed.

M & L for brushing neat cement slurry (3 Kg of cement per Sqm) mixed with chemical compound in the proportion chemical compound, water and cement (1:4:7) or as per manufacturer's instructions for bonding of old concrete surface to new concrete, complete all as specified and as directed.

M & L for PCC (1:2:4) type B0 (using 12.5mm graded crushed stone aggregate) mixed with integral water proofing chemical compound, mixed in proportion 200 milli litre per 50 Kg cement as in padding, benching, sunken portion etc., on roof surface for correcting/making proper slope on roof, etc.,complete all as specified and directed.

M & L for cutting 75 mm wide and 65 deep in brick wall/PCC block/RCC surface any location shaping horizontal face groove filled with PCC (1:2:4) type B0 using 12.5mm graded crushed stone aggregate with and including chemical compound mixed in proportion 200 mili litre per 50 Kg of cement or as per manufacturer's instructions laid when concrete is still green, complete all as specified and as directed.

M & L for rendering 10mm thick in CM (1:4) on concrete/brick surfaces with liquid water proofing compound @ 200 ml/50 Kg of cement or as per manufacturer's instructions finished even and smooth without using extra cement over roof/sunken slab/wall , complete all as specified and as directed. NOTE: Water proofing liquid will be measured and paid separately.

M & L for Water Proofing treatment on "non approachable/non accessible roof" surface (Horizontal and vertical surfaces) in following sequence through manufacturer/authorised applicator of the manufacturer all as specified and directed complete. (i) Applying approved bituminous based primer conforming to IS: 3384-1955 @ 0.3 Kg/Sqm to be applied on top surface of prepared surface till the surface is properly impregnated. (ii) Laying APP (Atactic polypropylene Polymer modified prefabricated membrane) water proofing membrane of weight not less than 3 Kg/Sqm with minimum 100 mm side overlap along the length from downward to upward completely sealed with Torch apllication /hot blown lamps. (iii) Applying two coats of bituminous based aluminium paint @ 0.3 Kg/Sqm, complete all as specified and as directed.

M & L for roof treatment in repair by complete removal of existing old treatment with following specifications:- (a) Priming plastered surface of roof by applying oil-based bitumen primer @ 0.30 Ltr/Sqm on plastered surface till the surface is properly impregnated. (b) Applying/laying APP based polymeric membrane 3 mm thick and weight should not be less than 3 Kg/Sqm and sealed the joint with torch application method. (c) Applying a coat of hot air blown grade bitumen of grade 85/25 @ 1.2 Kg/Sqm. Complete all as specified and as directed by Engr-in-Charge.

M & L cement concrete tiles 300mmX300mm X 22mm thick set and jointed and pointed in neat cement slurry with grey cement and no pigment in floors over and including 15mm thick cement screed bed in cement mortar (1:6) complete all as specified & directed.

M & L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg per Sqm in sunken portion including cleaning of surfaces, complete all as specified and as directed.

S & F 50 mm bore GI tube, light grade as in spout pipe, complete with all fittings laid as in floor etc., complete all as specified and as directed.

Supply only water proofing compound (liquid), ISI marked.

Taking down chowkhats or frames with shutter (without taking of shutter from the frame) of any description n.exc 1.5 Sqm each, complete all as specified and directed by Engr-In-Charge .

Taking down chowkhats or frame with shutter exc 1.0 Sqm each and n.exc 4 Sq m, (without taking off shutter from frame) and removing from site, complete all as specified and directed by Engr-In-Charge .

Taking shutters of any description exc 1.00 Sqm and n.exc 2 Sq m each, and removing from site, complete all as specified and directed by Engr-In-Charge .

Dismantling of boarding any description, fixed in any position with scews, complete all as specified and directed.

Resecuring or easing and adjusting without taking down shutter of any description exc 1 Sqm and n.exc 2 Sqm each, complete all as specified and as directed.

S & F 1.25 mm thick, pressed steel frames of size 125 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges lock strike plate,etc complete as specified and directed.

S & F 1.25 mm thick, pressed steel frames of size 105 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges lock strike plate,etc complete as specified and directed.

M & L Chowkhat 2nd class hard wood and frames wrought , framed rebated on the solid rounded or chamfered , put together with glue pinned at joints complete all as specified and directed by Engr-In-Charge

S & F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both side, complete all as per specified and directed.

S & F of 30 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. divided into squares, with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. fitted to chowkhats for doors etc., complete size of the members of shutter is as specified in clause No. 8.24 (a) of MES schedule 2009, part – I (Specifications) complete all as specified and directed.

S & F for Steel window with side hung shutter including box type hinge with steel handle, and steel peg stay complete with glazing bars dovetailed or welded, complete all as specified and directed.

S & F for Steel window with side hung shutter including box type hinge with steel handle, and steel peg stay complete without glazing bars dovetailed or welded, complete all as specified and directed.

S & F steel window, ventilators, fixed type with glazing bars, complete all as specified and as directed.

M & L for hold fast; wall ties; hooks for hanging fans; plan angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde E-165, complete all as directed.

S & F framed work such as grill grating etc with end of bars shouldered and/or riveted or forged into spikes framed guard bars barred iron doors, ladders etc. and similar works conforming to Fe-410-0 or Fe 310-0 including all necessary welding complete all as specified and directed by Engr-In-Charge.

S & F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tubes suppyling & fixing in opening as per specification & drawing complete all as spcefied and directed by Engr-In-Charge .

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS framed shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail &bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS framed welded/sealed to stiles & rails with suitable PVC sheet beading & joined together with solvent cement complete all as supplying and fixing in the frame at site as per specification and drawing incl. 3 Nos butt hinges 100 mm long for each door, complete all as specified and as directed.

M & L 18/19mm thick prelaminated particle board interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screw for cupboard shutter, shelf, etc., complete all as specified and directed by Engr-In-Charge .

M & L block boards 18/19mm thick grade 2, quality, interior grade, commercial type for cupboard shutter, shelf, etc., complete all as specified and as directed.

S & F countinuous piano hinges mild steel bright finish 30mm flap, complete all as specified and directed.

S & F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed by Engineer -In-Charge.

S&F Ball catcher with 8mm dia steel ball and brass body and striking plate including letting in and fixed, complete all as specified and as directed.

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples, complete all as specified and directed by Engr-In-Charge .

M & L for 3mm thick plain sheet glass ordinary quality and glazing with oil putty n.exc 0.50 Sqm in each pane, complete all as specified and as directed by Engr-In-Charge .

M & L for 3mm thick figured sheet glass ordinary quality and glazing with oil putty n.exc 0.50 Sqm in each pane, complete all as specified and as directed by Engr-In-Charge .

S & F 125mm hasp and staple safety type aluminium anodised including bolt to hinge plate and fixed with screw, compelte all as specified and as directed.

S & F 100mm butt hinges medium weight medium cold rolled mild steel complete all as specified and directed by Engr-In-Charge .

S & F 75 mm butt hinges medium weight medium cold rolled mild steel complete all as specified and directed by Engr-In-Charge.

S & F Aluminium anodised barrel tower bolts 200 mm long of extruded section, complete all as specified and as directed.

S & F Aluminium anodised barrel tower bolts 125 mm long of extruded section, complete all as specified and as directed.

S & F Aluminium anodised handles 125 mm long of extruded section, complete all as specified and as directed.

S & F mild steel sliding door bolts 250mm long, with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections and fixed, complete all as specified and directed by Engr-In-Charge .

S & F in repair MS ordinary rat tail rod pattern springs 300 mm including roller and roller plate complete, complete all as specified and directed by Engineer -In-Charge.

S & F 150 mm long overall length of cover plate floor door stopper of aluminium alloy body and tounge anodised with hard drawn spring fixed in floor, complete all as specified and as directed.

M & L PCC 1:3:6, type C-1 (using 20mm graded aggregate) for bed block for fillings for hold fasts etc., complete all as specified and as directed.

S & F in repair Harrison rails, anodised aluminium alloy with bracket etc., complete all as specified and as directed by Engr-in-Charge.

S & F for brass CP bracket fancy type suitable for fixing to 20 mm dia curtain rod, complete all as specified and as directed.

Dismantling old broken floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish of the premises complete all as specified and directed.

Demolition of plain cement concrete in ground floor paving n.exc 15 cm thick (below or above ground level) complete all as specified and as directed. (11+3)

Roughening surface of old concrete floor by picking, sweeping washing down with water to remove dust etc., , complete all as specified and as directed.

M & L for machine cut kota stone slab flooring 18-20mm thick over 20mm screed bed in cement mortar (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M & L for machine cut kota stone slab flooring 40-50mm thick over 20mm screed bed in cement mortar (1:4) as in step tread in one piece in one step, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M & L for white marble stone flooring, 16-18mm thick over 20mm screed bed in cement mortar (1:4), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M & L for machine cut kota stone slab flooring 18-20mm thick as in riser of steps, skirting over 15mm screed bed in cement mortar (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M & L glazed ceramic coloured tiles of size 450x300x7 mm thick as in dado/skirting etc set and jointed in neat cement slurry and pointed in colour cement to match the tiles including 10 mm thick cement plaster in CM (1:3), complete all as specified and directed.

M & L joint free non skid coloured ceramic tiles 7 to 8 mm thick (sqaure/rectangular) area of each tile exe. 0.11 sqm but n.exe.0.18 sqm, in floors etc., over and including 15mm thick screed bed in cement mortar (1:4) set and jointed in neat cement slurry and pointed in coloured cement to match the existing surfaces, complete all as specified and directed.

M & L joint free non skid coloured ceramic tiles 7 to 8 mm thick (sqaure/rectangular) area of each tile exe. 0.11 sqm but n.exe.0.18 sqm, in skirting, dado, etc., over and including 10mm thick rendering in cement mortar (1:4) set and jointed in neat cement slurry and pointed in coloured cement to match the existing surfaces, complete all as specified and directed.

M & L for 75 mm thick plain cement concrete (1:3:6) mix, type C-1 using 20mm graded stone aggregate as in plinth protection, finishing the surfaces even and fair without using extra cement, including 10 mm wide, 75mm deep joints made at 3.00 m in length and filled with bitumen 85/25 and sand in the ratio 1:3, complete all as specified and directed.

M & L for cement concrete type B1, 1:2:4 (using 12.5 mm graded aggregate) in levelling courses, coping, window cill etc., complete all as specified and directed.

M & L 5 mm thick rendering on or concrete surfaces as in ceiling, with cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and directed.

M & L for PCC (1:5:10) type E2 using 40 mm graded brick aggregate as in sunken portion, sub-base, etc., complete all as specified and as directed.

Demolition of cement concrete reinforced as in chullah hoods, shelves, cover slab and plate form, etc,complete all as directed by Engr-in-Charge

M & L for precast cement concrete type B-1 (1:2:4) using 20 mm graded aggregate aas in cover slab, shelves chajja and similar work set in cement mortar (1:4), complete all as specified and as directed.

S & F mild steel TMT bars 8 to 10mm dia and over cut to length, bent to shape required including cranking, bending spirally for hooping, hooking ends and binding with mild steel wire (annealed) not less than 0.90 mm dia or securing with clips, complete all as specified and directed.

M & L for machine cut cudappah stone slab 20-25 mm thick over and including 15mm thick screed bed in cement mortar (1:4) and jointed with grey cement slurry mixed with pigments to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M & L for rounding of edges of Kota/Cuddapah stone slab one edge, such as in steps, cooking platform and other similar work, complete all as specified and as directed.

Taking up and down GI tubing including GI fittings complete from trench/wall/ceiling/floor suitable for 15mm dia pipe, complete all as specified and as directed.

Taking up and down GI tubing including GI fittings complete from trench/wall/ceiling/floor suitable for 20mm dia pipe, complete all as specified and as directed.

Taking up and down GI tubing including GI fittings complete from trench/wall/ceiling/floor suitable for 25mm dia pipe, complete all as specified and as directed.

S & F for GI tubing medium grade including all types of fittings of ISI marked laid in trenches/walls/floor suitable for 15 mm bore, complete all as specified and as directed.

S & F for GI tubing medium grade including all types of fittings of ISI marked laid in trenches/walls/floor suitable for 20 mm bore, complete all as specified and as directed.

S & F for GI tubing medium grade including all types of fittings of ISI marked laid in trenches/walls/floor suitable for 25 mm bore, complete all as specified and as directed.

Refixing of GI tubing and connection including new GI fittings complete in trenches/wall/ceiling/floor suitable for 15 mm dia pipe, complete all as specified and as directed.

Refixing of GI tubing and connection including new GI fittings complete in trenches/wall/ceiling/floor suitable for 20 mm dia pipe, complete all as specified and as directed.

Refixing of GI tubing and connection including new GI fittings complete in trenches/wall/ceiling/floor suitable for 25 mm dia pipe, complete all as specified and as directed.

S & F 500 Ltr capacity rotational moulded polyethene water storage tanks, (cylinder vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I, including 20 mm dia of ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed, complete all as specified and as directed.

S & F in repair flushing cistern low level, PVC 10 lit capacity syphonic action type, valveless with inlet ball valve, float valve and handle including bracket and 32mm flush pipe of polyethylene, complete all as specified and as directed.

S & F PVC connecting pipe 15mm size with PTMT nuts of length 450mm, to wash hand basin, complete all as specified and as directed.

S & F 15 mm dia angle stop valve of cast copper alloy, fancy type, chromium plated, complete all as specified and directed.

M & L gun metal, globe or gate valves 20mm dia with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and as directed.

M & L gun metal, globe or gate valves 15mm dia with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and as directed.

S & F bib tap, 15mm, cast copper alloy CP with crutch butterfly handle, screwed for iron pipe or brass ferrule, complete all as specified and as directed. (24+120)

S & F in repair, 15mm dia bore stop valve cast copper alloy, fancy type chromium plated with long shank and cup (concealed) screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe, complete all as specified and directed.

S & F in repairs for shower rose chromium plated with or without swivel joints 125 mm dia, complete all as specified and as directed.

S & F in repair vitreous China wash hand basin, white, flat back, size 550X400mm including , chain and plug, and porcelain stopper, cast iron brackets, waste pipe complete including cutting for and pinning in ends of brackets and 32 mm dia waste fitting brass chomium plated for wash hand basin etc; with long screwed shanks and fly nuts, flange end bedded in red lead cement , complete all as specified and directed.Make:- Hindware/Parryware/Cera or of equivalent approved make.

S & F vitreous China squatting pan (Orissa pattern), of size 580x440 mm white with integral foot rests (excluding flusing cistern and flush pipe) including provn of lime concrete and backing joints, connection to trap and flushing pipe anti syphonage pipe etc., complete all as specified and as directed.

S & F in repair 15 mm bore fancy type pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'HOT' or 'COLD’ with long screwed shank and fly nuts, screwed for iron pipe complete all as specified and directed.

S & F shelf 450 mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (min weight 300 gms), complete all as specified and as directed.

Supply and fix in repairs stainless steel sink with drainage board made out of 1.00 mm thick sheet for kitchen with plug washers, waste pipe including bedding in cement mortar on dwarf wall or including cast iron cantilever brackets connecting union overall size 915 X 460 mm with bowl size 410 X 330 X 160 mm and including 38/40 mm dia waste pipe, complete all as specified and directed.(Make: model No-BSSBSD-52 of Blue Star or equivalent Prayag polymer pvt ltd / Nirali) or equivalent make as approved.

S & F in repairs stainless steel utensil Kitchen plate rack of size 24"X36"X10" with steel shelves and hanging arrangments for utensil, complete all as specified and directed. (MAKE : Cat pat No KPR-312 of Bluestar or other equivalent make as approved)

S & F CP towel rail, 20mm dia, D type, 60cm long, complete all as approved by Engr-in-charge.

Taking down cement plaster on brick wall or concrete surface etc.including raking out joints, hacking for key scrubbing down with water etc and removing of debris from site, complete all as directed.

Demolition of brick work build in cement mortar including all quoins, arches, pillars, etc. built in cement mortar complete all as specified and directed.

M & L brick work with sub class B old size bricks straight on curved on plan exc. 6m mean radius built in cement mortar 1:6 complete all as specified and directed by Engr-In-Charge .

M & L for rendering 15mm thick on fair faces of bricks/concrete surface work in cement mortar (1:6) finished even and fair without using extra cement, complete all as specified and as directed.

M & L for rendering 15mm thick on fair faces of bricks/concrete surface work in cement mortar (1:4) using Water Proofing Compound (WPC) on walls finished even and smooth without using extra cement, complete all as specified and as directed. (Note: WPC shall be measured separately)

M & L for rendering in cement mortar (1:3) on fair faces of cement concrete on ceiling of thickness 5mm finished the surface even and smooth without using extra cement, complete all as specified and as directed.

M & L for repair and rendering 10mm thick in cement mortar (1:3) on chajjas n.exc 60cm width after removing cracked plaster and concrete including cleaning of visible reinforcement and treating with cement slurry also necessary repair to cracked concrete if any with cement concrete (1:2:4) type B-0 using 12.5 mm graded aggregate including necessary work for double/single storey building, complete all as specified and as directed.

Taking down eaves gutters and rain water pipes (any size or pattern) , including all fittings, heads, shoes, bends, swan-necks, etc., including removing from site, complete all as specified and directed by Engineer-in-charge.

S & F, 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed on walls, including PVC clamps etc. complete all as specified and as directed by Engineer-in-charge.

S & F, 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed on walls, including PVC clamps etc., complete all as specified and as directed by Engineer-in-charge.

S & F, 110mm bore PVC (SWR) bends any radius complete all as specified and as directed by Engineer-in-charge.

S & F, 75mm bore PVC (SWR) bends any radius complete all as specified and as directed by Engineer-in-charge.

S & F PVC (SWR) 110 mm bore junction single, (Single T) equal or unequal, complete all as specified and as directed.

S & F PVC (SWR) 75 mm bore junction single, (Single T) equal or unequal, complete all as specified and as directed.

S & F 110mm bore PVC(SWR) vent Cowl complete all as specified and directd.

S & F 75 mm dia outlet PVC(SWR) floor trap plain with steel grating including jointing with solvent cement, complete all as specified and as directed.

S & F 110 mm dia PVC(SWR) WC connector with lip ring, complete all as directed and as specified.

M & L for preparation of new wooden of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

M & L for preparation of old decorated surface of wood or wood based materials of any description over 10cm width or girth and applying one coat of synthetic enamel paint all as specified and directed.

M & L for preparation of newly surfaces of steel of any description over 10 CM width or girth and applying two coats of synthetic enamel paint over a coat of zinc chorme primer, complete all as specified and directed

M & L preparation of newly plastered surface of walls and applying three coats of white wash on surface, complete all as specified and directed.

M & L preparation of newly plastered surface of ceiling and applying three coats of white wash on the surface, complete all as specified and directed.

M & L preparation of old decorated surface of walls by brooming down and wire brusing etc and applying one coat of white wash on wall, complete all as specified and directed.

M & L preparation of old decorated surface of ceiling and applying one coat of white wash on wall, complete all as specified and directed.

M & L for preparation of new plastered surfaces of wall and applying two coat of wall care putty to make the entire surface free from undulations, completell all as specified and as directed.

M & L for two coats of wall care putty on surface including preparation of surface make it smooth so as to receive, finishes including scrapping of existing treatment, complete all as specified and as directed.

M & L two coats of oil bound distemper on newly prepared wall care putty surfaces, complete all as specified and as directed.

M & L for preparation of newly plastered surfaces of wall and applying two coats of cement based paint, complete all as specified and as directed.

M & L for preparation of old plastered surfaces of wall by complete removal of existing treatment and applying one coat of cement based paint, complete all as specified and as directed.

M & L for anti-termite treatment of soil under existing floors using emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar (1:2) (1 cement:2 coarse sand) to match the existing floor, complete all as specified and as directed.

M & L for anti-termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc., in apron, complete all as

M & L for anti-termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 Lit/hole by drilling 6mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same, complete all as specified and as directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket bell or power) complete with all fitting such as batten, switch, ceiling rose, pendant, regulator, socket and brackets switch fuse etc removing materials from site and making good disturbed surfaces of walls, floors etc to match the existing surface all as directed .

M & L for point wiring for one light/ fan point/call bell controlled by one switch with 1100 volt grade PVC insulated 1.5 Sq mm multi stranded copper conductor cable with continuous earth wire of 1.5 Sq mm multi stranded copper conductor cable PVC insulated-unsheathed, drawn in & including concealed rigid non metallic PVC conduit medium grade with fittings (ISI marked) not less than 20 mm dia & sunken anodized pressed sunken boxes made out of not less than 1.0 mm thick sheet, covered with 2.8 mm thick laminated insulated cover make sheet for housing/fixing switches etc complete all as specified and directed.

All as per item No 127 here-in-before but one bell/buzzer point controlled by one push button on independent board.

All as per item No 127 here-in-before but 5 Amp socket outlet on same board.

All as per item No 127 here-in-before but for 5 Amp switch socket on independent board.

M & L for point wiring for 15 Amp power controlled by one 15 Amp switch with 1100 volt grade PVC insulated 2.5 Sq mm multi stranded copper conductor cable with continuous earth wire of 2.5 Sq mm multi stranded copper conductor cable PVC insulated-unsheathed, drawn in & including concealed rigid non metallic PVC conduit medium grade with fittings (ISI marked) not less than 25 mm dia & sunken anodized pressed sunken boxes made out of not less than 1.6 mm thick sheet, covered with 2.8 mm thick laminated insulated cover make sheet for housing/fixing switches, sockets etc., complete all as specified and directed.

S & F switch piano flush button single pole one way 5 Amp, complete all as specified and as directed.

S & F Switch socket combination 2 in 1, 3 pin, 5Amp and 15 Amp flush type, universal, complete all as specified.

S & F Switch socket combination 2 in 1, 3 pin, 5 Amp, flush type, universal, complete all as specified.

S & F socket outlet 2 in 1, 3 pin, 5Amp, flush type, universal, complete all as specified.

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc, complete all as specified.

S&F call bell Ding dong, AC 230 volts, single pole complete all as specified.

S & F bell push, single pole one way flush type, 5 Amp, complete all as specified and as directed.

Supply and fix ceiling rose three terminals PVC/ Polycarbonate, isolated body complete all as specified.

S & F lamp holder, PVC/Polycarbonate type with back plate having matching colour to holder suitable for angle/batten fittings (ISI marked), complete all as specified.

S & F LED Bulb of capacity 15 Watts lumen output (500) length 102 mm dia 56 mm base cap B22, (ISI marked) complete with all accessories base (ISI marked) all as specified and directed by Engr-in-Charge. Cat Part no. LHLDERHEML8X015 of Havells or its equivalent Of make Bajaj/Phillips/Crompton Greaves, complete all as specified and as directed.

S & F in repair LED light fitting 1 x 22, 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to fitting, complete all as specified and as directed by Engr-in-Charge. Make: Havells/Bajaj/Crompton Greaves/Phillips.

S & F in repair LED light fitting 1 x 9W/1x10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and as directed. Make: Havell/Bajaj/Phillips/Crompton Greaves.

S & F in repair LED light fitting mirror type with high output diffuser 2 feet 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and as directed. Make: Havell/Bajaj/Phillips/Crompton Greaves.

S & F exhaust fan, steel body AC single phase, 230V of size 300 mm sweep with blades and frame and louvers, complete all as specified and as directed. Make: HAVELLS/BAJAJ/USHA/CROMPTON GREAVES/KHAITAN.

S & F sheet metal enclosures for DBs when MCBs to used single pole and neutral (SPN) double door 240 volts, 8 way with IP-43 IK-09 protection including 200 Amp bus bar and neutral link (ISI marked), complete all as specified and as directed.

S & F amp rating 240V, 10 kA 'C' Curve miniature circuit breaker (MCB) of single poles and neutral and current carrying capacity 32 Amp in the MCB DB complete with connection testing and commissioning all as specified and as directed. Make: IndoAsian or its equivalent make in Havells/Standard/L&T.

S & F sheet metal enclosures for DBs when MCBs to be used in vertical tipple pole and neutral (VTPN) double door 415 volts, 6 way, with IP-43 IK-09 protection including 200 Amp rated bus bar and neutral link (ISI marked), complete all as specified and as directed.

S & F 240V, 10 kA 'C' Curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 Amp in the MCB DB complete with connection testing and commissioning all as specified and as directed. Make: IndoAsian or its equivalent make in Havells/Standard/L&T.

S & F 415V, 10 kA 'C' Curve Miniature Circuit breaker (MCB) of TPN, and current carrying capacity of 63 Amp in the DB, complete with connection testing and commissioning all as specified and as directed. Make: IndoAsian/Havells/Standard/L&T.

M & L for sub-main wiring with 2 runs of 6 Sqmm PVC insulated multi stranded FRLS copper conductor cable drawn through PVC concealed conduit not less than 25 mm with all fixing accessories along with one run of 6 Sqmm solid copper cable as earth continuity conductor, complete all as specified and as directed. Note:- (i) Two runs of 6 Sqmm and one run of 6 Sq mm cable as earth along with PVC conduit will be measured as one length. (ii) Proper colour coding to be adopted.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated screebedm PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor 50 Sq mm, 3.5 core nominal cross section including testing , complete all as specified and as directed by Engr-in-Charge.

M&L ,for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts check nuts & washers of galvanised iron or steel, protected by GI pipe 15 mm bore (light grade) and watering pipe 20 mm bore GI pipe (light grade) and PCC of chamber and coping shall in 1:3:6 type C-1 using 20 mm graded stone aggregate including excavation and earth work and removal of surplus soil and filling with black cotton soil upto ground level complete all as shown in electrical plate No 3 of SSR Pt-I, 2009 with CI cover 10mm thick of size 300x300mm with charcoal dust and common salt complete and earth lead connected to panel including testing complete all as specified and directed. Note : Earth test result should not less than one ohm.

S & F Electric water heater, storage type, steel body, with copper inner tank and heating element upto 2 KW capacity 25 Lit, BEE 5 Star, rated complete with all accessories such as safety valve, thermostat, NRV, connection accessories etc., complete all as specified and as directed.

S & F sheet metal enclosures single pole and neutral (SPN) with two pin and earth plug and socket, complete with one single pole MCB 20 Amps, complete all as specified and as directed.

S & F PVC connections 15mm size with PTMT nuts washers of length 450mm flexible (ISI marked), complete all as specified and directed.

S & F 15mm dia bore stop valve cast copper alloy, fancy type chromium plated with long shank and cup (concealed) screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe, complete all as specified and directed.

Excavation, in trenches n.exc 1.5 m wide & n.exc 1.5 m in depth for laying cable/pipes and getting out in soft/loose soil, complete all as specified and as directed.

Returning, filling in trenches including spreading, leveling, watering and well ramming in layers n.exc 25 cm thick, complete all as specified and as directed.

Removing excavated materials n exc 50 m and depositing, where directed at a level n exc 1.5m above the starting point all as directed.

M&L for reinforced precast concrete cable cover class LV, type 2, flat, size 250 mm x 150 mm x 40mm all as specified and directed

M & L for underground sand filling in cable trenches for cable protection with clean dry unwashed sand including gently punning in layer of 15 cm and 8 cm (total 23 cm) in thickness all across the laid portion of LT cable in trenches, complete all as specified and as directed by Engr-in-Charge. (Note: punned thickness only shall be considered for payment)

Supply and laying GI pipe 50mm bore light grade with fitting for cable protection at road crossing/under concrete including taking down of old one, complete all as specified and as directed.

M/S AMOD KUMAR PANDEY