Repair, Renovation Of Residential Quarters Of PDA at Pahalgam

Earth work in excavation by manual means in trenches for foundation over areas (not exceeding 1.5 m in width ) including disposal of excavated earth lead upto 25 meters and lift upto 1.5 m, as directed by Engineer-in-Charge in all kinds of soils

Providing and laying of hand packed stone boulder (size 150mm-230mm) before laying of PCC compacted consolidated rammed filling the voids compacting all complete carriage upto site of work all head loads complete job.

Providing and laying in position cement concrete 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:

Providing and laying in position cement concrete of specified grade including curing butexcluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete.

Chequerred terrazzo tiles 22mm thick with graded marble chips of size upto 6mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing, polishing and curing complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) . Ordinary cement without any pigment.

12mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand)

Painting with synthetic enamel paint of approved brand and manufactureto give an even shade Two or more coats on new/ old wood work (color as per directions of EIC)

P/F of 12mm thick imported wood paneling (newzealand pine or equivalent) of approved pattern overand including base of 10mm thick plywood with frame work of Budloo finishing exposed surface with two of more coats of touch wood and polish including cost of nails, adhesive material, cornices etc. and all carriages (Design of panelling to be approved by EIC)

Ruled/flush pointing on Brick masonry surface with lime, surkhi and marble dust mortar in the ratio 1:1.5:1/2 one lime : 1.5 surkhi ( 50% red and 50% light yellow surkhi):1/2 marble dust ( the 130.720Sqm 409.052 53471.277 and 50% light yellow surkhi):1/2 marble dust ( the rate is inclusive of all materials and labours involved including scaffolding) carriage complete

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 meters lead Of area of 3 sqm. and below

Dismantling tile work in floors and roofs laid in cement mortar incl. stacking the material within 50 m lead for thickness of tile 10 mm to 25 mm.

Providing and laying floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm (Anti Skid).

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete 600*1200mm size

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, and polishing to edges to give high gloss finish etc. complete at all levels (Area of slab over 0.5 sqm) : 18 mm Granite

Provdng and fixing of ornamental corices (75X75mm) including allattachments complete job First Class Kail Wood)

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately). 30mm First Class deodar wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. Decorative ply wood both side decorative veneer (type 1) conforming to IS 1328 BWR type

Providing and fixing bright finished brass handles with screws etc. complete : 125 mm

Providing and fixing bright finished brass handles with screws etc. complete : 100 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete. : 100x10 mm

Providing wood work in truess work fixed in position with hold fast lugs or with dash fasteners of required dia and length KD wood

P/F of (Pergo flooring) of approved pattern anddesign, sheds including cost " of mmn thickthermocol foam underneath / 25 mm thick cornice with fixing adhesive etc. complete in all respects.

Construction of wardrobes using BWR 19mm thick ply board (ply to ply) for frames, shutters. The job shall include fixing of dulmica of approved shade/texture on all exposed surfaces, inner linings prefrebly white (Mica), hardware fittings like hinges, handles, tower bolts. locks, hanger rail etc as per requirements of architectural drawings or as directed by the Engineer-In-charge, complete job ) (600mm deep)

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 18.2.1 W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : 18.7.1 White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fitting

Providing and fixing complete divertor set with plate, single liver ,spout, body and wall shower incl all neccessary fittings and fixtures. Complete job[jaquar or equival brand)

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal di

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet 150 mm diameter

Providing and fixing toilet paper holder C.P. brass

Providing and fixing PTMT soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour: 600 mm long towel rail with total length of 645 mm, 78 mm wide and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing brass stop cock of approved quality. 19.10.1 15 mm nominal bore

Providing and Fixing of 6 door Storage Cabinet made of Engineered Wood Self Assembled with dimensions (180x200x46.5 mm) with all accessories included.Design to be approved by Engineer in Charge (Speciality Panels or eq)

providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing PTMT grating of approved quality and colour. 19.49.1 Circular type 150 mm nominal size square 100 mm diameter of the inner hinged round grating

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge. Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc. PN-16 pipe, 16mm OD(SDR-7.4)

PN-16 pipe , 20mm OD(SDR-7.4)

PPR Union 20mm

PPR Union 25mm

Providing and fixing ball valve 20 mm PPR of approved make

Providing and fixing ball valve 32 mm PPR of approved make

Providing and fixing PVC pipes including PVC fittings laid in required gradient, inclding cost of all fixing accessories complete job as directed by EIC (type C) 75mm dia

100 mm dia

carriage of material by using mech tpt for an average lead of 50 kms sand/bajree

Supply, Installation, Testing and Commissioning of 12W/+ LED recessed/mounted (round or square) Down lighters having aluminum body, minimum 100lm/w, average life 50000 hours, Operating temperature -10°C to +45°C.Certification:- LM79 & LM80 test report should be from govt approved In-house NABL lab/ government of India.The job includes replacement warranty of fixture if damaged/ burnt out what so ever reason for a period of two years reckoned from the date of successful commissioning/ handing over of site to the intending department. (Havells/ Philips/ Crompton/ Jaguar/Wipro).

Supply, Installation, Testing and Commissioning of 50W (Havells/ PhillIps/Wipro skyline ) new generation energy saving and environmental friendly long life L.E.D Flood Light made up of pressure die cast Aluminum housing with high efficiency LEDs as lighting source with efficacy >110lm/w ,CRI>80 ,CCT>5000 ,Avg Life L70 50000 hours ,No haremful UV and IR radiators, Operating Temp -10 to 45C ,Surge Voltage Protection, IP66 Protection and impact resistance of IK07.The job includes replacement warra

nty of fixture if damaged/ burnt out what so ever reason for a period of two years reckoned from the date of successful commissioning/ handing over of site to the intending department.

Wiring for light/power plug points AC Points with 2x4 sq mm FRLS PVC insulated flexible stranded copper conductor wires in recessed or surface medium class PVC conduit along with 1x4 sq. mm FRLS PVC insulated copper conductor single core cable for earthing, etc. as required.(Havells/ Polycab/ Anchor/ SSK/KEI/RR or equivalent make ) excluding the cost of conduit.

Wiring for 5- 10A socket out lets for computer (inverter) with 2X2.5 sq. mm FRLS PVC insulated copper conductor (Havells/ Polycab/ Anchor/ SSK/KEI/RR or equivalent make ) as directed by engineer incharge.) single core cable in surface/recessed medium class PVC conduit, alongwith 1 No. 2.5 sq. mm FRLS PVC insulated copper conductor single core cable for earthing etc. as required excluding the cost of conduit.

Supplying and fixing of GI box along with modular base and cover plate for modular sockets, switches in recess etc as required 6 module (200mm x 75mm)

Supplying and fixing of 5pin 5-10A socket and 5-10A switch on existing modular plate, incl connections etc as required. (Havells/SSK/Anchor/ABB/Schneider)

Supply, installation, testing and commissioning of 40A DP rating 240/415V,10 KA "C" curve MCB of Legrand/ Havells/ L&T/ABB suitable for inductive load in the MCB distribution board complete with necessary connections.

Wiring for Circuit/Sub mains along with earth wire in FRLS PVC insulated 660/1100 volt grade flexible stranded copper conductor wires in recessed or surface conduiting system, excluding the cost of conduit. (Havells/ Polycab/ SSK/ Anchor/KEI/RR or equivalent). 2x 6 sq mm + 1x 6 sq mm AC Submain

2x 1.5 sq mm

Supply, Installation, Testing and Commissioning of 3 star rating 1.5 Ton Inverter type (Hot and Cold) split Air Conditioner suitable for operation on AC supply single phase 50Hz 230V with hermetically sealed inverter compressor with air cooled condenser latest R410A/ R-32 refrigerant fan motor, start and run capacitors, relay and over load protector internal unit with one indoor and one outdoor unit. The indoor unit fitted on wall by employing suitable clamps and the outdoor unit will be placed on angle iron stand fitted with nut/bolts outside the room to avoid noise, including standard length of suitable size copper tubing covered with nitrilic foam, topping up with refrigerant for additional length of piping if required, PVC flexible drain pipe, suitable capacity 3 core sheathed/ PVC insulated copper cable and a battery operated wireless remote unit. The job includes repairs to walls wherever the same are cut.Complete Job (Panasonic/Daikin/Godrej/LG/Lloyd/ Voltas)Sample to be approved by EIC before installation.

Supply, Installation, Testing and Commissioning of 4KVA automatic relay type Voltage Stabilizer for 1.5 ton AC operating from input voltage 90-260V thereby producing 230+-3 output voltage.sample to be approved before installation.

Supply, Installation,Testing and Commissioning of Surface mount 25A MCB Box Protected Socket PVC plastic base incl. 25A plug top,with shutter for child safety and 25 A SPMCB inside a closed box.