CONVERSION OF OH LINE TO UG LT WITH CONNECTED ITEMS AT RAMGARH CANTT UNDER GE RAMGARH

Amount

Excavation, in trenches n.exc 1.5 m wide & n.exc 1.5 m in depth for laying cable/pipes and getting out in soft/ loose soil, complete all as directed.

Returning, filling in trenches including spreading, leveling, watering and well ramming in layers n.exc 25 cm thick, complete all as directed.

Removing excavated materials (soil) to a distance n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the staring point, complete all as directed.

M&L for Sub class "B" bricks laid dry width wise across the line of cable in trenches as cable protection complete all as directed.

M & L,for Supplying and laying unreinforced precast concrete cable cover, Class LV, Type I, flat, size 250mm x 150mm x 40mm complete all as directed.

Supply and laying clean and dry sand free from sharp material (unwashed) in trenches around the cable for cushioning complete all as directed.

M&L for boring of hole under road, pavement, hard standing by trenchless using manual technique with required tools complete all as directed. Note:- (i) Pipes shall be laid minimum 1.00 mtr to 1.50 mtr below/ under existing road surfaces/ apron/ floors etc. (ii) T&P required for road boring to be provided by the contractor at site own cost and not any extra claim entertained on this account on later stage. (iii) During execution of work any damage occured, contractor must repair/ rectify the same day beyond this @ Rs 500/- per day penalty will be imposed and not any extra claim will be entertained on this account

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 400 sq mm 3.5 core complete all as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 240 sq mm 3.5 core complete all as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 150 sq mm 3.5 core complete all as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 120 sq mm 3.5 core complete all as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 95 sq mm 3.5 core complete all as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70 sq mm 3.5 core complete all as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3.5 core complete all as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core complete all as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core complete all as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 04 core complete all as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 04 core complete all as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6 sq mm 04 core complete all as directed. Note for Ser item No 08 to 19:- (i) Excavation, earth work, sand cushioning, cover for cable protection, GI protection pipe shall be measured and paid saperately under respective items of BOQ. (ii) The contractor will be provided necessary thimble, Lugs and MCCB spreader link of suitable size connection with bush bar/ LT panel/ DBs rate will be included in unit quoted rate, not any claim will be entertained on this account.

Supply and fixing GI Pipe light grade of size 80 mm bore with all fittings for passing of cables fixed to pole / wall / laid under floor or roads including all fixing accessories complete for protection of cable complete all as directed.

Supply and fixing GI Pipe light grade of size 50 mm dia with all fittings for passing of cables fixed to pole / wall / laid under floor or roads including all fixing accessories complete for protection of cable complete all as directed.

Earthing complete with GI earth plate electrode 60cmX60cmX6mm thick, burried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to GI earth strip of size 32x6 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No-3 of SSR Part-I connected to LT panel boards including excavation and connected earth work in hard/dense soil, PCC 1:3:6 type C-1 as in pit, 20mm dia GI pipe medium grade for watering pipe, 40 mm dia bore GI light grade as earth strip protection pipe, 50 mm thick RCC 1:2:4 type B-1 cover slab of size 300x300x50mm as earth pit cover reinforced with 8 mm dia TMT bars @ 10 cm C/C both ways and with handle made out of 10 mm dia bars, funnel, strainer, charcoal and testing on completion complete all as directed. Note:- Rate quoted deemed to be included excavation and earth work in any type of soil with PCC type C1 in pit Cover & other arrangement complete all as directed.

S&F moulding compound (SMC) of box street light junction box of size 205mmx255mmx112mm complete with shock and rust proof, termite resistant, temper proof, front openable type incl suitable provn for 3 phase 4 wire cable (size upto 25 Sqmm 4 core) incoming and outgoing loop- in - loop out connection and including one No of MCB ,SP 6 amp "B" series breaking capacity 10KA and non metallic clamps, GI nut bolts and washers of suitable size and fixed on pole/ wall complete all as directed.

Supply and fixing in provision cable PVC insulated unsheathed of size 2.5 Sqmm 2 core copper conductor for connections from junction box to security light complete all as directed. (for juction box to security light).

Taking down and removing LED street light/security light of any make and wattage and depostied to MES store for keeping in safe custody for reuse and refixing at its original location complete all as directed.

Refixing of LED street light/security light of any make and wattage at its original location complete all as directed.

Supply and fixing building security lights with new generation energy saving & environment friendly long life versatile pressure die-cast aluminium IP65/66 roadway luminaire with high power LEDs as light source & exclusively designed polycarbonate cover alongwith electronic driver type street light fitting 35 watt capacity LED and including all accessories duly pre-wired, fixing on existing bracket with nut, bolts & washers as required at site for fixing of street light on LT pole/ wall complete including taking old street light fitting any type and description complete all as directed.

M&L for installation, commissioning & testing in provision of plinth mounted LT panel board outdoor type factory made CPRI approved, fabricated out of 3.15 mm thick CRCA Sheet, dust and vermin proof, totally enclosed metal clad, single door, accessible from front side with locking arrangement, 3 phase 4 wire system at AC 440 V, 50 HZ with colour coded copper bus bar of rated current capacity 500 A complete applied with two coats of synthetic enamelled paint over a coat of anti corrosion primer and mounted on angle iron of size 40x40x5 mm grouted in PCC foundation including earth work and excavation complete suitable to accommodate the following accessories (Main panel No. 01 at cinema hall) : - (i) Digital multifunction meter 0-500 volt, AC 3 Phase - 01 No (ii) Panel indicating lamp LED type (Red ,Yellow & Blue) with holder and fuse holder 230/240 Volts, AC - 01 Set (Set of three) (iii) Panel instrumental wiring with FRLSH 4 to 6 sqmm copper conductor cable single core of required length - 01 Job (iv) Four pole MCCB 160 Amp, 50Hz, 415 Volts with repturing capacity 36KA, adjustable thermal magnetic type - 01 No (as incomer) (v) Four pole MCCB 80 Amp, 50Hz, 415 Volts with repturing capacity 25KA, adjustable thermal magnetic type - 02 No (vi) Four pole MCCB 63 Amp, 50Hz, 415 Volts with repturing capacity 25KA, adjustable thermal magnetic type - 01No (vii) MCB TPN 32 Amp, 50 Hz, 415 V with rupturing capacity 10KA - 02 No (viii) Digital timer switch of 28 memory locations, current capacity 16 Amp - 01 No (ix) Contactor for timer switch - 01 No Note : (a) The height of panel should be 0.60 mtr from ground level with PCC foundation. (b) Cost for construction of plateform for panel of brick masonary work in CM 1:6 with foundation PCC 1:4:8 type D-2 (using 40 mm thick stone aggerate ), including plaster work, PCC coping 1:2:4 (using 20 mm thick stone aggerate ), deemed to be included in the item rate. No extra payment will be made.

M&L for installation, commissioning & testing in provision of plinth mounted LT panel board outdoor type factory made CPRI approved, fabricated out of 3.15 mm thick CRCA Sheet, dust and vermin proof, totally enclosed metal clad, single door, accessible from front side with locking arrangement, 3 phase 4 wire system at AC 440 V, 50 HZ with colour coded copper bus bar of rated current capacity 500 A complete applied with two coats of synthetic enamelled paint over a coat of anti corrosion primer and mounted on angle iron of size 40x40x5 mm grouted in PCC foundation including earth work and excavation complete suitable to accommodate the following accessories (Main panel No. 02 at 20/4 camp corner) : - (i) Digital multifunction meter 0-500 volt, AC 3 Phase - 01 No (ii) Panel indicating lamp LED type (Red ,Yellow & Blue) with holder and fuse holder 230/240 Volts, AC - 01 Set (Set of three) (iii) Panel instrumental wiring with FRLSH 4 to 6 sqmm copper conductor cable single core of required length - 01 Job (iv) Four pole MCCB 250 Amp, 50Hz, 415 Volts with repturing capacity 36KA, adjustable thermal magnetic type - 01 No (as incomer) (v) Four pole MCCB 125 Amp, 50Hz, 415 Volts with repturing capacity 25KA, adjustable thermal magnetic type - 01 No Spare (vi) MCB TPN 32 Amp, 50 Hz, 415 V with rupturing capacity 10KA - 02 No (vii) Digital timer switch of 28 memory locations, current capacity 16 Amp - 01 No (viii) Contactor for timer switch -01 No Note : (a) The height of panel should be 0.60 mtr from ground level with PCC foundation. (b) Cost for construction of plateform for panel of brick masonary work in CM 1:6 with foundation PCC 1:4:8 type D-2 (using 40 mm thick stone aggerate ), including plaster work, PCC coping 1:2:4 (using 20 mm thick stone aggerate ), deemed to be included in the item rate. No extra payment will be made.

M&L for installation, commissioning & testing in provision of plinth mounted LT panel board outdoor type factory made CPRI approved, fabricated out of 3.15 mm thick CRCA Sheet, dust and vermin proof, totally enclosed metal clad, single door, accessible from front side with locking arrangement, 3 phase 4 wire system at AC 440 V, 50 HZ with colour coded copper bus bar of rated current capacity 500 A complete applied with two coats of synthetic enamelled paint over a coat of anti corrosion primer and mounted on angle iron of size 40x40x5 mm grouted in PCC foundation including earth work and excavation complete suitable to accommodate the following accessories (Main panel No 03 at front of SPMK) :- (i) Digital multifunction meter 0-500 volt, AC 3 Phase - 01 No (ii) Panel indicating lamp LED type (Red ,Yellow & Blue) with holder and fuse holder 230/240 Volts, AC - 01 Set (Set of three) (iii) Panel instrumental wiring with FRLSH 4 to 6 sqmm copper conductor cable single core of required length - 01 Job (iv) Four pole MCCB 250 Amp, 50Hz, 415 Volts with repturing capacity 36KA, adjustable thermal magnetic type - 01 No (as incomer) (iv) Four pole MCCB 100 Amp, 50Hz, 415 Volts with repturing capacity 25KA, adjustable thermal magnetic type - 02 No (v) Four pole MCCB 63 Amp, 50Hz, 415 Volts with repturing capacity 25KA, adjustable thermal magnetic type - 04 No (vi) MCB TPN 32 Amp, 50 Hz, 415 V with rupturing capacity 10KA - 02 No (vii) Digital timer switch of 28 memory locations, current capacity 16 Amp - 01 No (viii) Contactor for timer switch - 01 No Note : (a) The height of panel should be 0.60 mtr from ground level with PCC foundation. (b) Cost for construction of plateform for panel of brick masonary work in CM 1:6 with foundation PCC 1:4:8 type D-2 (using 40 mm thick stone aggerate ), including plaster work, PCC coping 1:2:4 (using 20 mm thick stone aggerate ), , deemed to be included in the item rate. No extra payment will be made.

M&L for installation, commissioning & testing in provision of plinth mounted LT panel board outdoor type factory made CPRI approved, fabricated out of 3.15 mm thick CRCA Sheet, dust and vermin proof, totally enclosed metal clad, single door, accessible from front side with locking arrangement, 3 phase 4 wire system at AC 440 V, 50 HZ with colour coded copper bus bar of rated current capacity 200 A complete applied with two coats of synthetic enamelled paint over a coat of anti corrosion primer and mounted on angle iron of size 40x40x5 mm grouted in PCC foundation including earth work and excavation complete suitable to accommodate the following accessories (FPB No.P-01,T-01,T-05 ) :- (i) Digital multifunction meter 0-500 volt, AC 3 Phase - 01 No (ii) Panel indicating lamp LED type (Red ,Yellow & Blue) with holder and fuse holder 230/240 Volts, AC - 01 Set (Set of three) (iii) Panel instrumental wiring with FRLSH 4 sqmm copper conductor cable single core of required length - 01 Job (iv) Four pole MCCB 63 Amp, 50Hz, 415 Volts with repturing capacity 25KA, adjustable thermal magnetic type - 01 No (As Incomer) (v) Four pole MCCB 50 Amp, 50Hz, 415 Volts with repturing capacity 16 KA, adjustable thermal magnetic type - 06 No Note : (a) The height of panel should be 0.60 mtr from ground level with PCC foundation. (b) Cost for construction of plateform for panel of brick masonary work in CM 1:6 with foundation PCC 1:4:8 type D-2 (using 40 mm thick stone aggerate ), including plaster work, PCC coping 1:2:4 (using 20 mm thick stone aggerate ), deemed to be included in the item rate. No extra payment will be made.

M&L for installation, commissioning & testing in provision of plinth mounted LT panel board outdoor type factory made CPRI approved, fabricated out of 3.15 mm thick CRCA Sheet, dust and vermin proof, totally enclosed metal clad, single door, accessible from front side with locking arrangement, 3 phase 4 wire system at AC 440 V, 50 HZ with colour coded copper bus bar of rated current capacity 200 A complete applied with two coats of synthetic enamelled paint over a coat of anti corrosion primer and mounted on angle iron of size 40x40x5 mm grouted in PCC foundation including earth work and excavation complete suitable to accommodate the following accessories (FPB No. P-02,) :- (i) Digital multifunction meter 0-500 volt, AC 3 Phase - 01 No (ii) Panel indicating lamp LED type (Red ,Yellow & Blue) with holder and fuse holder 230/240 Volts, AC - 01 Set (Set of three) (iii) Panel instrumental wiring with FRLSH 4 sqmm copper conductor cable single core of required length - 01 Job (iv) Four pole MCCB 80 Amp, 50Hz, 415 Volts with repturing capacity 25KA, adjustable thermal magnetic type - 01 No ( As Incomer) (v) Four pole MCCB 63 Amp, 50Hz, 415 Volts with repturing capacity 16 KA, adjustable thermal magnetic type - 06 No Note : (a) The height of panel should be 0.60 mtr from ground level with PCC foundation. (b) Cost for construction of plateform for panel of brick masonary work in CM 1:6 with foundation PCC 1:4:8 type D-2 (using 40 mm thick stone aggerate ), including plaster work, PCC coping 1:2:4 (using 20 mm thick stone aggerate ), deemed to be included in the item rate. No extra payment will be made.

M&L for installation, commissioning & testing in provision of plinth mounted LT panel board outdoor type factory made CPRI approved, fabricated out of 3.15 mm thick CRCA Sheet, dust and vermin proof, totally enclosed metal clad, single door, accessible from front side with locking arrangement, 3 phase 4 wire system at AC 440 V, 50 HZ with colour coded copper bus bar of rated current capacity 200 A complete applied with two coats of synthetic enamelled paint over a coat of anti corrosion primer and mounted on angle iron of size 40x40x5 mm grouted in PCC foundation including earth work and excavation complete suitable to accommodate the following accessories (FPB No. H-1,T-3 ) :- (i) Digital multifunction meter 0-500 volt, AC 3 Phase - 01 No (ii) Panel indicating lamp LED type (Red ,Yellow & Blue) with holder and fuse holder 230/240 Volts, AC - 01 Set (Set of three) (iii) Panel instrumental wiring with FRLSH 4 sqmm copper conductor cable single core of required length - 01 Job (iv) Four pole MCCB 100 Amp, 50Hz, 415 Volts with repturing capacity 25KA, adjustable thermal magnetic type - 01 No (As incomer) (vii) Four pole MCCB 63 Amp, 50Hz, 415 Volts with repturing capacity 16 KA, adjustable thermal magnetic type - 08 No Note : (a) The height of panel should be 0.60 mtr from ground level with PCC foundation. (b) Cost for construction of plateform for panel of brick masonary work in CM 1:6 with foundation PCC 1:4:8 type D-2 (using 40 mm thick stone aggerate ), including plaster work, PCC coping 1:2:4 (using 20 mm thick stone aggerate ), deemed to be included in the item rate. No extra payment will be made.

M&L for installation, commissioning & testing in provision of plinth mounted LT panel board outdoor type factory made CPRI approved, fabricated out of 3.15 mm thick CRCA Sheet, dust and vermin proof, totally enclosed metal clad, single door, accessible from front side with locking arrangement, 3 phase 4 wire system at AC 440 V, 50 HZ with colour coded copper bus bar of rated current capacity 200 A complete applied with two coats of synthetic enamelled paint over a coat of anti corrosion primer and mounted on angle iron of size 40x40x5 mm grouted in PCC foundation including earth work and excavation complete suitable to accommodate the following accessories (FPB N0. T-2 &T-4) : - (i) Digital multifunction meter 0-500 volt, AC 3 Phase - 01 No (iii) Panel indicating lamp LED type (Red ,Yellow & Blue) with holder and fuse holder 230/240 Volts, AC - 01 Set (Set of three) (iv) Panel instrumental wiring with FRLSH 4 sqmm copper conductor cable single core of required length - 01 Job (v) Four pole MCCB 100 Amp, 50Hz, 415 Volts with repturing capacity 25KA, adjustable thermal magnetic type - 01 No (As Incomer) (vi) Four pole MCCB 63 Amp, 50Hz, 415 Volts with repturing capacity 16KA, adjustable thermal magnetic type - 08 No Note : (a) The height of panel should be 0.60 mtr from ground level with PCC foundation. (b) Cost for construction of plateform for panel of brick masonary work in CM 1:6 with foundation PCC 1:4:8 type D-2 (using 40 mm thick stone aggerate ), including plaster work, PCC coping 1:2:4 (using 20 mm thick stone aggerate ), deemed to be included in the item rate. No extra payment will be made.

M&L for installation, commissioning & testing in provision of plinth mounted LT panel board outdoor type factory made CPRI approved, fabricated out of 3.15 mm thick CRCA Sheet, dust and vermin proof, totally enclosed metal clad, single door, accessible from front side with locking arrangement, 3 phase 4 wire system at AC 440 V, 50 HZ with colour coded copper bus bar of rated current capacity 300 A complete applied with two coats of synthetic enamelled paint over a coat of anti corrosion primer and mounted on angle iron of size 40x40x5 mm grouted in PCC foundation including earth work and excavation complete suitable to accommodate the following accessories (FPB No. R-1): - (i) Digital multifunction meter 0-500 volt, AC 3 Phase - 01 No (ii) Panel indicating lamp LED type (Red ,Yellow & Blue) with holder and fuse holder 230/240 Volts, AC - 01 Set (Set of three) (iii) Panel instrumental wiring with FRLSH 4 sqmm copper conductor cable single core of required length - 01 Job (iv) Four pole MCCB 160 Amp, 50Hz, 415 Volts with repturing capacity 25KA, adjustable thermal magnetic type - 01 No (as incomer) (v) Four pole MCCB 63 Amp, 50Hz, 415 Volts with repturing capacity 16KA, adjustable thermal magnetic type - 10 No Note : (a) The height of panel should be 0.60 mtr from ground level with PCC foundation. (b) Cost for construction of plateform for panel of brick masonary work in CM 1:6 with foundation PCC 1:4:8 type D-2 (using 40 mm thick stone aggerate ), including plaster work, PCC coping 1:2:4 (using 20 mm thick stone aggerate ), deemed to be included in the item rate. No extra payment will be made.

M&L for installation, commissioning & testing in provision of plinth mounted LT panel board outdoor type factory made CPRI approved, fabricated out of 3.15 mm thick CRCA Sheet, dust and vermin proof, totally enclosed metal clad, single door, accessible from front side with locking arrangement, 3 phase 4 wire system at AC 440 V, 50 HZ with colour coded copper bus bar of rated current capacity 300 A complete applied with two coats of synthetic enamelled paint over a coat of anti corrosion primer and mounted on angle iron of size 40x40x5 mm grouted in PCC foundation including earth work and excavation complete suitable to accommodate the following accessories (FPB No. R-2): - (i) Digital multifunction meter 0-500 volt, AC 3 Phase - 01 No (ii) Panel indicating lamp LED type (Red ,Yellow & Blue) with holder and fuse holder 230/240 Volts, AC - 01 Set (Set of three) (iii) Panel instrumental wiring with FRLSH 4 sqmm copper conductor cable single core of required length - 01 Job (iv) Four pole MCCB 160 Amp, 50Hz, 415 Volts with repturing capacity 25KA, adjustable thermal magnetic type - 01 No (as incomer) (v) Four pole MCCB 160 Amp, 50Hz, 415 Volts with repturing capacity 16KA, adjustable thermal magnetic type - 01 No (vi) Four pole MCCB 63 Amp, 50Hz, 415 Volts with repturing capacity 16KA, adjustable thermal magnetic type - 01 No Note : (a) The height of panel should be 0.60 mtr from ground level with PCC foundation. (b) Cost for construction of plateform for panel of brick masonary work in CM 1:6 with foundation PCC 1:4:8 type D-2 (using 40 mm thick stone aggerate ), including plaster work, PCC coping 1:2:4 (using 20 mm thick stone aggerate ), deemed to be included in the item rate. No extra payment will be made

S&F factory made epoxy powder coated sheet metal enclosures for Distribution Board VTPN DB's 4 ways, 415 volt grade , with metal double door including 200 amp rated copper bus bar with two neutral bar , earth bar & cable ties for cable management fully insulated bus bar with set of wires and door earthing with provision of space for MCCB as incomer and SP/TP MCB as out going four way including strandard DIN rail, for cable management, top and bottom removeable gland plates with knockouts complete all as directed.

S&F MCCB 4 Pole, 415 V, fixed type, 100 Amps with breaking capacity 16 kA with enclouser complete all as directed.

Dismantling of ACSR conductors from steel/PCC poles, service feeder or distributor span complete all as directed.

Dismantling of stay assembly complete, (demolition of concrete, etc and excavation measured separately) complete all as directed.

Dismantling of insulators any type, any size from cross-arms of MS Channels or angle sections etc complete all as directed.

Dismantling of cross-arms of MS channel or angle sections etc. complete all as directed.

Taking out from trenches/ pole XLPE cable and service wire with aluminium conductor, 1100 volts grade, Any size complete all as directed.

M&L for installation, commissioning & testing in provision of plinth mounted LT panel board outdoor type factory made CPRI approved, fabricated out of 3.15 mm thick CRCA Sheet, dust and vermin proof, totally enclosed metal clad, single door, accessible from front side with locking arrangement, 3 phase 4 wire system at AC 440 V, 50 HZ with colour coded copper bus bar of rated current capacity 500 A complete applied with two coats of synthetic enamelled paint over a coat of anti corrosion primer and mounted on angle iron of size 40x40x5 mm grouted in PCC foundation including earth work and excavation complete suitable to accommodate the following accessories (Main panel No. 01 ,17 Camp) : - (i) Digital multifunction meter 0-500 volt, AC 3 Phase - 01 No (ii) Panel indicating lamp LED type (Red ,Yellow & Blue) with holder and fuse holder 230/240 Volts, AC - 01 Set (Set of three) (iii) Panel instrumental wiring with FRLSH 4 to 6 sqmm copper conductor cable single core of required length - 01 Job (Incommer) (iv) Four pole MCCB 315 Amp, 50Hz, 415 Volts with repturing capacity 50KA, adjustable thermal magnetic type - 01 No (as incomer) (Outgoing) (v) Four pole MCCB 125 Amp, 50Hz, 415 Volts with repturing capacity 25KA, adjustable thermal magnetic type - 03 No (vi) Four pole MCCB 100 Amp, 50Hz, 415 Volts with repturing capacity 25KA, adjustable thermal magnetic type - 02 No (vii) Four pole MCCB 63 Amp, 50Hz, 415 Volts with repturing capacity 25KA, adjustable thermal magnetic type - 03 No (x) MCB TPN 100 Amp, 50 Hz, 415 V with rupturing capacity 10KA - 02 No (xi) Digital timer switch of 28 memory locations, current capacity 16 Amp - 01 No (xii) Contactor for timer switch - 01 No Note : (a) The height of panel should be 0.60 mtr from ground level with PCC foundation. (b) Cost for construction of plateform for panel of brick masonary work in CM 1:6 with foundation PCC 1:4:8 type D-2 (using 40 mm thick stone aggerate ), including plaster work, PCC coping 1:2:4 (using 20 mm thick stone aggerate ), deemed to be included in the item rate. No extra payment will be made.

M&L for installation, commissioning & testing in provision of plinth mounted LT panel board outdoor type factory made CPRI approved, fabricated out of 3.15 mm thick CRCA Sheet, dust and vermin proof, totally enclosed metal clad, single door, accessible from front side with locking arrangement, 3 phase 4 wire system at AC 440 V, 50 HZ with colour coded copper bus bar of rated current capacity 200 A complete applied with two coats of synthetic enamelled paint over a coat of anti corrosion primer and mounted on angle iron of size 40x40x5 mm grouted in PCC foundation including earth work and excavation complete suitable to accommodate the following accessories (FPB No. 01, 02,03 ) :- (i) Digital multifunction meter 0-500 volt, AC 3 Phase - 01 No (ii) Panel indicating lamp LED type (Red ,Yellow & Blue) with holder and fuse holder 230/240 Volts, AC - 01 Set (Set of three) (iii) Panel instrumental wiring with FRLSH 4 sqmm copper conductor cable single core of required length - 01 Job (Incommer) (iv) Four pole MCCB 125 Amp, 50Hz, 415 Volts with repturing capacity 25KA, adjustable thermal magnetic type - 01 No (Outgoing) (v) Four pole MCCB 63 Amp, 50Hz, 415 Volts with repturing capacity 16 KA, adjustable thermal magnetic type - 05 No Note : (a) The height of panel should be 0.60 mtr from ground level with PCC foundation. (b) Cost for construction of plateform for panel of brick masonary work in CM 1:6 with foundation PCC 1:4:8 type D-2 (using 40 mm thick stone aggerate ), including plaster work, PCC coping 1:2:4 (using 20 mm thick stone aggerate ), deemed to be included in the item rate. No extra payment will be made.

M&L for installation, commissioning & testing in provision of plinth mounted LT panel board outdoor type factory made CPRI approved, fabricated out of 3.15 mm thick CRCA Sheet, dust and vermin proof, totally enclosed metal clad, single door, accessible from front side with locking arrangement, 3 phase 4 wire system at AC 440 V, 50 HZ with colour coded copper bus bar of rated current capacity 200 A complete applied with two coats of synthetic enamelled paint over a coat of anti corrosion primer and mounted on angle iron of size 40x40x5 mm grouted in PCC foundation including earth work and excavation complete suitable to accommodate the following accessories (FPB N0. 04 & 06) : - (i) Digital multifunction meter 0-500 volt, AC 3 Phase - 01 No (ii) Panel indicating lamp LED type (Red ,Yellow & Blue) with holder and fuse holder 230/240 Volts, AC - 01 Set (Set of three) (iii) Panel instrumental wiring with FRLSH 4 sqmm copper conductor cable single core of required length - 01 Job (Incommer) (iv) Four pole MCCB 100 Amp, 50Hz, 415 Volts with repturing capacity 25KA, adjustable thermal magnetic type - 01 No (Outgoing) (v) Four pole MCCB 63 Amp, 50Hz, 415 Volts with repturing capacity 16KA, adjustable thermal magnetic type - 05 No Note : (a) The height of panel should be 0.60 mtr from ground level with PCC foundation. (b) Cost for construction of plateform for panel of brick masonary work in CM 1:6 with foundation PCC 1:4:8 type D-2 (using 40 mm thick stone aggerate ), including plaster work, PCC coping 1:2:4 (using 20 mm thick stone aggerate ), deemed to be included in the item rate. No extra payment will be made.

M&L for installation, commissioning & testing in provision of plinth mounted LT panel board outdoor type factory made CPRI approved, fabricated out of 3.15 mm thick CRCA Sheet, dust and vermin proof, totally enclosed metal clad, single door, accessible from front side with locking arrangement, 3 phase 4 wire system at AC 440 V, 50 HZ with colour coded copper bus bar of rated current capacity 300 A complete applied with two coats of synthetic enamelled paint over a coat of anti corrosion primer and mounted on angle iron of size 40x40x5 mm grouted in PCC foundation including earth work and excavation complete suitable to accommodate the following accessories (FPB No. 05 and 7): - (i) Digital multifunction meter 0-500 volt, AC 3 Phase - 01 No (ii) Panel indicating lamp LED type (Red ,Yellow & Blue) with holder and fuse holder 230/240 Volts, AC - 01 Set (Set of three) (iii) Panel instrumental wiring with FRLSH 4 sqmm copper conductor cable single core of required length - 01 Job (Incommer) (iv) Four pole MCCB 100 Amp, 50Hz, 415 Volts with repturing capacity 25KA, adjustable thermal magnetic type - 01 No (as incomer) (Outgoing) (vii) Four pole MCCB 50 Amp, 50Hz, 415 Volts with repturing capacity 16KA, adjustable thermal magnetic type - 04 No Note : (a) The height of panel should be 0.60 mtr from ground level with PCC foundation. (b) Cost for construction of plateform for panel of brick masonary work in CM 1:6 with foundation PCC 1:4:8 type D-2 (using 40 mm thick stone aggerate ), including plaster work, PCC coping 1:2:4 (using 20 mm thick stone aggerate ), deemed to be included in the item rate. No extra payment will be made.

S & F Cable route indicator made of MS sheet of size 200mm x 150mmx 3mm thick and spot welding with angle iron of size 40mm x40mm x5mm thick ,750mm long embeded in PCC 1:2:4 ,type B-1, (using 12.5mm graded stone aggregates) including providing one coat of synthetic enamel black paint over a coat of red oxide primer including writing LT cable ,440volt with white paint complete all as directed.

M/S DEEPAK KUMAR SINHA (BID ID -3429841)

M/S ROHIT CONSTUCTION (BID ID -3429742)

M/S KANCHAN KANTI BAKSI (BID ID -3433819)