Special repair to Bldg No. T-10 and T-35 in 26/3/S Camp at Yol Cantt under AGE B/R-II of GE (KH) YOL

Amount

PART-I:- Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.50 Sqm each and removing from site, complete all as specified and directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.50 Sqm but not exc. 4 Sqm each and removing from site, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting any gauge, thickness including Nainital or similar pattern roof covering, complete all as specified and directed.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sqcm in section, unframed work in any position, complete all as specified and directed.

Dismantling timber scantlings 40 sqcm and over in section, in any position, framed work, complete all as specified and directed.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness including cover fillets in ceiling, complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry built in cement mortar including all quoins arches, pillars, including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe.290 Gde E-165, steel work, complete all as specified and directed.

Rolled sections as in Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes provided as post, struts to support the rafter portion of truss, conforming to I.S.1161- 1979 grade St.-240s, steel work, complete all as specified and directed.

Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins angle for shed where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc. conforming to grade Fe.290.Gde-E-165, steel work, complete all as specified and directed.

Mild Steel framed work as Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete, conforming to Fe 290 Gde E-165, complete all as specified and directed.

Mild steel 16mm dia bolts purpose made with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. exc 30cm long, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Clip-in false ceiling system with plain steel beveled edged tile 600mmx600mm manufactured out of 0.70mm GI sheet having powder coating with 60 microns polyester paint on front side. Two sides of each tile shall be rised and piped and stopped to ensure postive engagement into the spring clip-in profile allowing for demounting of indivual tiles. The rigid suspension system consists of rows of galvanized steel 0.50mm thick clip-in profile of size 38mmx20mm and installed at 600mm c/c spacing to support the tiles clip-in profiles shall be suspended and jointed from galvanized steel 'C' channels of size 10mmx38mmx10mm with hold on clamps at spacing as specified by manufacturer. Suspension angles shall be suspended from the roof structure by GI ceiling brackets as per manufacturer instructions. GI wall angle shall be used on wall of size 20mmx30mmx20mm and 0.50mm thick with matching the colour with tiles all as per manufacturer specifications/instructions and including necessary scaffolding, complete all as specified and directed by Engr-In-Charge and GE.

Pressed steel frames of size 125x60mm for door with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, including one shop coat of primer and taring back side of frame, complete all as specified and directed.

35mm thick flush shutters, solid core construction with block board core and plywood face panels commercial type on both sides covered with decorative veneer with lipping/frame to match type, complete all as specified and directed by Engr-In-Charge.

Factory made second class hard wood (Sal) glazed and Skelton door shutters 35mm thick open rebated and prepared to receive glass gauge etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass or gauge etc., size of members of shutter as specified in clause 8.24 (a) of part-I, fitted to chowkats, complete all as specified and directed.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 180 of MES SSR 2020 Part-II, complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of 5mm thick plain coloured PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1), complete all as specified and directed.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet and edges shall be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 176- of MES SSR 2020 Part-II, complete all as specified and directed.

Factory made fully glazed PVC window/ventilator shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; complete specified and directed. Note:- Glass shall be measured and paid separately.

Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 85mm x 35mm double rebated comprises gauged, glazed skelton shutter (for glass and wire gauge) ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC M-15, type B-0 (04 No's for each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including following fitting welded to frame shutter:- (i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window. (ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf. (iii) MS tower bolt 150mm long - 2 No per leaf. (iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf. (v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf. (vi) Mild steel butt hinge of size 75mm x 12mm - 2 Nos per leaf. (vii) Flat iron fillets of size 20X3 mm for fixing wire gauge. (viii) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 06/07. Make : As per Appendix 'C'. Note:-(i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day.

Mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed ballusters walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165, complete all as specified and directed.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads, fixed, complete all as specified and directed.

Small fittings of 2nd class hard wood (SAL) such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including 50mm long, medium weight, cold rolled mild steel butt hinge, articles not exc. 200 cu.cm. each, complete all as specified and directed.

Butt hinges (ISI marked), medium weight, cold rolled stainless steel 75mm long, complete all as specified and directed.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 150mm, fixed, complete all as specified and directed.

Extruded aluminium alloy handles (ISI marked), fabricated type, anodised, of size 150mm, complete all as specified and directed.

Butt hinges (ISI marked), medium weight, cold rolled stainless steel 100mm long, complete all as specified and directed.

Aluminium alloy, anodised,sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 300mm, complete all as specified and directed.

Applying two coats of synthetic enamel paint over a coat of pink primer on new wood surfaces of any description not otherwise described, exc. 10cm width or girth including preparation of surfaces, complete all as specified and directed.

Sheet glass 3mm thick ordinary quality and glazing with oil putty/aluminium beads in squares, not exc. 0.50 sqm in each pane, complete all as specified and directed.

3mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.50 Sqm in each pane, complete all as specified and directed.

Applying two coats of synthetic enamel paint over a coat of red oxide on new steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, complete all as specified and directed.

Machine cut kota stone slab flooring 18-20mm thick of size not less than 550 mm X 550mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 15mm screed layer in cement mortar 1:4 (1 cement : 4 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish, laid over PCC sub base, complete all as specified and directed.

Machine cut kota stone,18-20mm thick, as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in vertical surfaces such as skirting/dado/riser to step/pillar aid over and including 10mm thick bedding layer in cement mortar 1:4 (1 cement : 4 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish, complete all as specified and directed.

Plain cement concrete M-15, nominal mix, type B-0, using 12.50mm graded mechanically crushed stone aggregate as in levelling course/floors, 25mm thick, surface finished even and fair, complete all as specified and directed.

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.18 Sqm but not exc. 0.38 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified and directed.

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 10mm thick (Square/ rectangular) area of each tile exc. 0.18 Sqm but not exc. 0.38 Sqm, as in skirting, dado etc . set and jointed in neat cement slurry and includingincluding 10mm thick rendering in cement mortar (1:4) including necessary cutting as per site requirement complete all as specified and directed. including necessary cutting and waste as per site requirement pointed in white or coloured cement to match, complete all as specified and directed.

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.06 Sqm but not exc. 0.11 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified and directed.

Glazed coloured tiles of size 300mmx200mm/450mmx300mmx7mm thick as in vertical surfaces such as jointed in neat cement slurry and pointed with coloured cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand), complete all as specified and directed.

Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5cm deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), complete all as specified and directed. Note:- The unit rate include for use of form work (straight or curved).

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. For fair finished flat surfaces of concrete, complete all as specified and directed.

Reinforced cement concrete (Nominal mix) M-15 (using 20mm graded crushed stone aggregate) as in beams, bressummers, cantilevers, lintel over 1.50m span, plinth band/lintel band, complete all as specified and directed. Note:- Reinforcement and form work shall be measured and paid separately.

Reinforced cement concrete (design mix) M-25 (using 20mm graded crushed stone aggregate) as in beams, cantilevers, lintel over 1.50m span, complete all as specified and directed.

PCC M-15, nominal mix, B-0 using 12.50mm graded mechanically crushed stone aggregate as, in lintels up to 1.50 metre clear span cuts, steps seismic and other similar bends, coping, bands plates for serving hold fasts etc. and the like including weathering slighting rounded or chamfered angles and throating, complete all as specified and directed. Note:- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be measured and paid separately.

TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips, complete all as specified and directed.

TMT bars 5mm dia and over up to 10mm, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips as in stirrups, spacers and binders, complete all as specified and directed.

Walling random rubble masonry with best quality locally available stone, uncoursed, well bonded, bedded, solidly hearted and built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified and directed.

Fly ash brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified and directed.

Brick work with old size fly ash bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 (1 cement : 4 coarse sand), complete all as specified and directed.

Taking down cement plaster on brick or stone walls, ceiling, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) on fair faces of brick wall or concrete surfaces, surface finished even and smooth without using extra cement with WPC, complete all as specified and directed. Note:- water proofing compound shall be measured and paid separately.

Rendering plaster 15mm thick in cement mortar 1:6 (1 cement :6 coarse sand) on other than fair faces of brick wall or stone wall surfaces, surface finished even and smooth without using extra cement, complete all as specified and directed.

Supply only Liquid water proofing compound, complete all as specified and directed.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over 1mm thick wall care putty including preparation of surface, complete all as specified and directed.

Complete removal of existing treatment and preparing old plastered wall surfaces and applying two coats of oil bound distemper over 1mm thick wall care putty including preparation of surface, complete all as specified and directed.

Preparation of newly plastered wall surfaces and appling two coats of cement base paint over a coat of chalk whitening, complete all as specified and directed.

Taking up or down 15mm bore, steel tubing and connections, including cleaning for refixing or removal from site, complete all as specified and directed.

Taking up or down 20mm bore, steel tubing and connections, including cleaning for refixing or removal from site, complete all as specified and directed.

Mild steel galvanized iron water tubing 15mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor, complete all as specified and directed.

Mild steel galvanized iron water tubing 20mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor/ sunken floor spout, complete all as specified and directed.

Bib taps with wall flange, fancy type 15mm bore, cast copper alloy with crutch or butterfly handle, screwed down, chromium plated screwed for iron pipe or for brass ferrule and fixed in repair, complete all as specified and directed.

Stop/Angle valve, fancy type with wall flange, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repairs, complete all as specified and directed.

Stainless steel single towel rail 20mm dia of size 600mm long, fixed in repair, complete all as specified and directed by Engr-In-Charge.

Soap dish, brass chromium plated, fixed to plugs with chromium plated, brass screws, fixed in repair, complete all as specified and directed.

Sheet glass shelf assembly consisting of 5.50mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed.

Disconnecting existing tanks and removing to store water tanks of capacity n.exc 500 ltr, complete all as specified and directed.

Rotational moulded polyethylene water storage tank 500 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position including PVC float ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line, complete all as specified and directed.

Gun metal, globe or gate valves, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 20mm bore iron pipe or for unions and fixed, complete all as specified and directed.

Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 20mm bore iron pipe or for unions and fixed in repairs, complete all as specified and directed.

Vitreous China wash down water closet (pedestal pattern), single piece white including traps, connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC coloured seat cover and chromium plated jet including PVC connection, fixed complete, including PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve, float and handle with brackets with PVC 32mm dia flushing pipe, anti-syphonage pipe, fixed in repair, complete all as specified and directed.

Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with PVC ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-1 using 20mm graded crushed stone aggregate complete all as specified, including PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve, float and handle with brackets with PVC 32mm dia flushing pipe, anti-syphonage pipe, fixed in repair, complete all as specified and directed.

Wash basins, Vitreous China (Flat back type) size 550mmx400mm, crystal white with and including cutting for and pinning on ends of brackets, 450mm long PVC connections 15mm size with PTMT coupling nuts at both ends, waste pipe of polythylene of low or high density or PVC of 32mm dia including Pillar taps fancy type, 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed in repair, complete all as specified and directed.

Vitreous china urinal, full stall type of approved size white colour with waste coupling of PTMT (half or full threaded) minimum weight 32mm-45gms/40mm-60gms, having urinal spreader for fixing with 15mm dia pipe (Minimum weight 60 gms) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement: fixing automatic flushing cistern with brackets, flush pipe PVC connections 15mm size with CP brass coupling nuts of length 450mm, grating and union for discharge pipe, fixed in repair, complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed stone ware, SWR, AC or RCC pipes) 100mm dia and removal of demolished materials from the site, complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed stone ware, SWR, AC or RCC pipes) 75mm dia and removal of demolished materials from the site, complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, in floors, trenches, fixed to wall with adjustable clamps of bore 110mm, complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, in floors, trenches, fixed to wall with adjustable clamps of bore 75mm, complete all as specified and directed.

PVC (SWR) junction single, (Single T) equal or unequal, 110mm bore, provided with oval access door, complete all as specified and directed.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement, dia of outlet 75mm, fixed, complete all as specified and directed.

PVC (SWR) bends any radius, 110mm bore jointed with solvent cement (fitted with oval access door), fixed, complete all as specified and directed.

PVC (SWR) bends any radius, 75mm bore jointed with solvent cement, fixed, complete all as specified and directed.

PCC M-10, nominal mix, C-1, using 20mm graded mechanically crushed stone aggregate as in filling in door frame and mass concrete, complete all as specified and directed.

Aluminium (diecast) body door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed, complete all as specified and directed.

Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and directed.

15mm bore brass CP mixer (Wall/ Sink/ WHB mixer as per requirement of site) for mixing hot & cold water screwed down for iron pipe and fixed in repair, complete all as specified and directed by Engineer in Charge.

Natural colour 15 micron powder coated anodized aluminium three track window with chowkhat aluminium grill of approved design complete all as directed with all fixing arrangements (including providing and fixing window handles, tower bolts and provision for fixing lock) including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- (a)Shutter vertical member 47.62 x 45.45 x 1.74mm weighing 0.881 Kg/RM. (b)Shutter top member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (c)Shutter bottom member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (d) Natural colour 15 micron anodized aluminium anodised frame of chowkhat of section 85.00 x 44.45 x 1.80 mm weighing 1.302 Kg/ RM, with flat iron hold fasts and necessary concrete to fix hold fasts all as directed. (e) 5.50mm thick tinted glass fixed with alumnium beading, silicon lining and gaskets complete. (f) The size of anodised aluminium round handle, fancy type shall be 100mm dia (02 Nos) and anodised aluminium tower bolt of size 100mm (02 Nos).

Supply fabricate & fix in position aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) door shutter with frame, partly glazed with 5mm thick tinted glass and partly panelled with 9mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position, aluminium door handle 150mm size, aluminium barrel tower bolt 200mm size etc all as specified below complete all as specified and directed. (a) Frame ( top & side) section shall of size 101.60 x 44.75 x 2.4mm (Section No 14021) (b) Vertical Members of shutter section shall be of size 85.00x44.45x2.00mm (section No 19560) (c) Top Members of shutter Section shall be of size 83.50 x 44.45 x 2.00mm (section No 19581) (d) Lock rail (Middle member) of shutter section shall be of size 150.00x44.45x3.00mm (section No 19596) (e) Bottom Members of shutter section shall be of size 150.00x44.45x3.10mm (section No 19584) (f) Glazing clip for securing glass of shutters shall be of 0.80mm thick (section No 19370) Note:- (i) Section No given above are of make jindal, contractor may use similar section of other make mention in Appx 'C'. (ii) Floor door spring will be measured & paid separately

PVC wall lining (Solid/ Hollow) consisting of 5mm thick wood grain colour PVC sheet inclusive of solvent cement and fixed at site on PVC frame as per specifications complete all as specified and directed by Engineer in Charge.

Chequered cement concrete tiles machine pressed of size 20cmx20cmx25mm/30cmx30cmx25mm thick with grey cement, set jointed & pointed in neat cement slurry mixed with pigment to match the shade of the slab in floors laid over and including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

Plain cement concrete M-7.5, nominal mix, type D-2, using 40mm graded mechanically crushed stone aggregate as in sub base to floor, 75mm thick, surface finished even and fair to receive top surface, complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc., complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed stone ware, AC or RCC pipes) 150mm dia and removal of demolished materials from the site, complete all as specified and directed.

Reinforced concrete pipes, class NP2, laid and jointed in cement mortar 1:2, complete with collars, bore of pipe 150mm, complete all as specified and directed.

Concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, in plain cement concrete M-7.5, nominal mix, type D-2 using 40mm graded stone aggregate, for bore of pipe 150mm. (For width and depth of PCC bed - refer preamble (a) (i) (ii) on page 391 of SSR Pt-II), complete all as specified and directed.

Cutting into existing manholes for connecting new drains, 150mm dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round 3/4 channel) in cement concrete M-15 type B-1 using 20mm graded crushed stone aggregate, smooth, finished and reforming benching as required, complete all as specified and directed.

Chipping of unsound/weak concrete/plastered material from slabs, beams, columns, stone/ brick masonry etc, with standard power driven percussion type or pneumatic chisel of standard make as directed by Engineer-in-Charge including tampering all edges, making square shoulders of cavities etc incl scoffolding complete and disposal of debris upto 2 km for 30mm average thickness for slabs/chajja/ceiling/ RCC wall/ Stone/ Brick Masonry, complete all as specified and all as directed by Engr-In-Charge.

Mixing and applying bonding coat, acrylic polymer modified cementitious bond coat @ 2.20 kg cement per sqm of surface area with specified proportion of polymer admixer (rate shall include cost of cement), on prepared surface of parent materials as per specification and direction, complete all as specified and directed by Engineer in Charge.

Providing and mixing polymer modified cement mortar in layer, each layer not exceeding 15mm thick, including trowelling with wooden tools etc, complete as per specification and direction of Engr-in- Charge. For payment purposes, pre-measurement of thickness shall be done just after the surface preparation is completed. Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounf/tapping with a blunt metal instrument.

(i) 30mm average thickness for slabs/chajja/ceiling/ RCC wall/ Stone/ Brick Masonry.

(ii) 40mm average thickness as on floor.

After successful surface prepartion apply PRIMER + 3 COAT of SHALICEM EWP--Highly Elastic Cementitious Elastomeric Coating with reinforcement fiber glass net of 40/50 gsm -- Food grade coating with Sprinkling of Sand, complete all as specified and directed by Engineer in Charge.

100mm thick Plain cement concrete M-7.5 nominal mix, D-2, using 40mm graded mechanically crushed stone aggregate as in sub base to floor, surface finished even and fair, complete all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

M&L for repair of honeycomb, construction joints, crack repairing and injection grouting-reconditioning of RCC water tank as follows:- (i) Chipping all loose concrete and cement plaster on the surface and desiliting if any (ii) all construction cold joints and cracks cutting 8mmx20mm in U &V shape. Cleaning of joints properly and applying primer bond coat of SBR based bonding agent slurry coat. Filling of joints cracks with high strength durable strong structural repair polymer fiber reinforced modified mortar- SHALIFIX-FRM and Shalimar DAM-It (iii) Drilling holes in concrete surface using electric drill for fixing of PVC nozzles (4 to 6 inch distance) at specific joint areas only whereever cracks, construction joints and honeycomb area only using 12-14mm dia, drilled upto 6 inch deep in the RCC structure placed and fixed with STP SHALI GROUT IP or SHALI SBR NON SHRNK FLOWABLE POLYMERISED LIQUID- pressure through injection pump. Checking and sealing removing of nozzles after injection process is overt. (iv) After successfull surface preparation apply primer + 3 coat of shalicem EWP--Highly Elastic Cementitious Elastomeric Coating with reinforcement fiber glass net of 40/50gsm-Food grade coating with sprinkling of sand, complete all as specified and directed by Engr-In-Charge.

Preparation of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

Taking down point wiring with aluminium/ copper conductor for light point, fan & socket point/ power point etc. complete including switches, sockets, holders, (batten or pendent type), ceiling rose, switch board, bell/buzzer, bell push, and making good to the disturbed surfaces of wall/ floor etc. to match with existing surfaces including white wash/ colour wash/ distempering to match with existing wall/ floor/ ceiling finishes, complete all as specified and directed.

Taking down sheet metal enclosure DB, main switch etc and making good distrubed surfaces to match with existing surfaces, complete all as specified and directed.

Point wiring with 1.50 Sqmm copper conductor FRLS (Multi strand) PVC insulated ISI Marked unsheathed cable in and including concealed PVC conduit medium grade, ISI marked of suitable size with all fittings/ accessories such as bends, cross, elbow, tees etc. of suitable size and also including PVC insulated ISI marked unsheathed 1.50 Sqmm copper multistranded conductor, 1100 volts grade FLRS as phase, neutral and earth wire connected to common earth dolly and including concealed MS pressed steel (modular sunken box) of suitable sizes terminal boxes made from 1.60mm thick sheet for mounting of switches, sockets, fan regulators, light fittings etc. and modular cover plate as top cover (ISI marked) for one light point or one fan/exhaust fan point or one bell point, independent, controlled by one way switch/ push button complete all as specified and directed. Note-: (a) Insulation test of point wiring. (b) colour coding is to be maintained. (Ph-Red, N-Black, Half -Yellow, Earth- Green). (c) Rate of cutting chases, cement plaster, white wash and making good as existing surface included in quoted rates. (d) Rate of modular cover plate and metal flux box included in quoted rates.

All as per serial item No '111' above, but for one 3 pin 5 Amps socket outlet on the same board with 1.50 sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 1.50 sqmm stranded copper conductor cable as continous earth wire, complete all as specified and directed.

All as per serial item No '111' above, but for one 3 pin 5 Amps socket outlet on the independent board with 1.50 sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 1.50 sqmm stranded copper conductor cable as continous earth wire, complete all as specified and directed.

All as per serial item No '111' above, but for 3 pin 15 amps socket out let on independent with 2.50 Sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 2.50 Sqmm stranded copper conductor cable as continuous earth wire, complete all as specified and directed.

S & F for modular switch 6A one way, single module, complete all as specified and directed.

S & F for modular blank plate, single module, complete all as specified and directed.

S & F for modular switch 16A one way, single module, complete all as specified and directed.

S & F for modular socket for 6A, 3 pin combined, 2 module, complete all as specified and directed.

S & F for modular socket for 6A/16A, 3 pin combined, 2 module, complete all as specified and directed.

Sheet metal enclosures factory made for DBs when MCBs to be used, single pole and neutral (double Door), 8 way, 240 volts with 200 Amp rated bus bar, complete all as specified and directed.

MCB SP 6 to 32 Amp, 240 Volts, 10 KA, B series including taking out old, complete all as specified and directed. Note:- The connection to the MCBs shall be done through thimble/lugs do not direct wire shall be connected to MCBs.

MCB SPN 40 to 63 Amp, 240 Volts, 10 KA B series including taking out old, complete all as specified and directed. Note:- The connection to the MCBs shall be done through thimble/lugs do not direct wire shall be connected to MCBs.

Supply and fix distribution board iron clad TPN DB double door with IP-43 protection 415 V 3 Phase 50 HZ 4 Way complete with appropriate size of copper busbar and neutral link complete and incl cutting chasing to wall for fixiing DB and making good the disturbed wall to match with existing surface, complete all as specified and directed.

MCB TPN 100 Amp, 415 Volts, 10 KA B series including taking out old, complete all as specified and directed. Note:- The connection to the MCBs shall be done through thimble/lugs do not direct wire shall be connected to MCBs.

M & L for ceiling rose 65 x 20mm three terminals, fixed in repair, complete all as specified and directed.

Replacement of LED Decorative ultra slim square profile LED lighting integral type fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack, 10 watt LED, 230V, and making connection with 2 core copper twisted flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light, complete all as specified and directed.

Replacement of LED Decorative ultra slim square profile LED lighting integral type fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack, 20 watt LED, 230V, and making connection with 2 core copper twisted flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light, complete all as specified and directed.

M & L for sub main wiring with two single core PVC insulated unsheathed, 1100 Volts grade, (FRLS) copper cable 6 sqmm stranded conductor and drawing through and including rigid PVC non metalic surface conduit medium duty (ISI Marked) with conduit accessories such as junction boxes, bends, tees etc. including continuous earth wire PVC insulated unsheathed 1100 volts grade, cable 6 sqmm copper conductor and connected to common earth dolly complete as directed including taking down old submain wiring, complete all as specified and directed. Note:- (i) One run of PVC conduit, two runs of cable (Phase + Neutral) and one run of earth wire shall be measured and paid as one unit.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC), complete all as specified and directed.

Supply and fixing LED security light of capacity 35 watts, 5700K, housing made of die cast aluminium with street optic lens with all accessories and connecting up with and including provision of 3 core flexible copper wire of size 1.50 sqmm from ceiling rose to security light drawn through GI light grade security light bracket not less than 1.50m in length alongwith fixing on wall, including taking down old light, complete all as required at site and directed by Engr - in - Charge.

Supply and fixing in replacement of LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V, AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as required at site and directed by Engr-in-Charge.

Replacement of earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of plate not less than 1.50m below ground level, connecting to galvanised iron wire 4.00mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15mm bore including provn of concrete pit in plain cement concrete M-20 type B-1 using 20mm graded crushed stone aggregates with 40mm thick cover of rainforced cement concrete M-20 reinforced with XPM (weight not less than 4 kg/Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50m, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion. NOTE :- Item of earthing includes the cost of 7.5 m long galvanised iron earth wire 4mm size and protection pipe of 15mm bore galvanised iron light grade and earth work.

M/S JATINDERA ENTERPRISES (BID ID -3313919)

MM Constructions (BID ID -3314282)

m/s Sohan singh barwal and Brothers (BID ID -3314369)