SPECIAL REPAIR TO BLDG NO P-115 (TOOLS STORE SECTION) OF AD REGT WKSP AT DHOLEWAL MIL COMPLEX UNDER GE LUDHIANA

Amount

Sch 'A' sec-I

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness ( below or above ground level).

Taking down cement plaster of any description on brick or concrete surfaces etc including racking out joints, hacking for key, scrubbing down with water etc.

Dismantling floor, hearth or wall tiles including cement mortar bedding(but not backing) and removing serviceable tiles to stores and rubbish off the premises.

Taking down chowkats or frames(without taking off shutters from the frame) area exc 1.5 Sqm but n.exc 4.0 Sqm each.Complete all as specified and directed.

Taking down chowkats or frames(without taking off shutters from the frame) area n.exc 1.5 Sqm each,Complete all as specified and directed.

Demolition of reinforcement cement concrete as in Roofs, floors (other than ground floors), beams staircases, landing, chajjas, and similar suspended work (reinforcement cut as reqd to facilitate demolition),Complete all as specified and directed.

M&L for reinforced Cement Concrete type B1 1:1.5:3 (M20) (nominal mix ) (using 20 mm graded stone aggregate) in Beams, cantilevers, lintels etc.Complete all as specified and directed.

M&L for reinforced Cement Concrete type B1 1:1.5:3 (M20) (nominal mix ) (using 20 mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings,balconies canopies and in shelves etc.

Use and waste rough finished flat Form work to sides and soffits of floor or roof beams, lintels, cantilevers, shelves including supports etc.Complete all as specified and directed.

Use and waste rough finished Form work to soffits of suspended slabs such as roof slabs and similar work not exceeding 200mm thick.

M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips quality.Complete all as specified and directed.

M&L for TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips.

M&L for 25mm thick cement concrete type B-1, 1:2:4 (20mm graded agg ) as in sub bases of floor Complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25mm thick over 20mm thick cement screed bed in cement mortar 1:6 laid and jointed with grey cement slurry mix with pigment to match the shade of slab including rubbing and polishing,Complete all as specified and directed.

All as per item No 14 above but in skirting/dado laid over 10mm thick cement screed in CM 1:4,Complete all as specified and directed.

M&L for glazed ceramic coloured/ printed tiles 450mm x 300mm x 6 to 7mm thick on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 10mm thick bedding layer in cement mortar (1:4) including necessary cutting as per site requirement complete all as specified and directed by Engineer-in-Charge.

M&L for 12mm thick rendering on brick work or concrete surfaces in cement mortar 1:6 finsihed the surfaces even and smooth without using extra cement. Complete all as specified and directed.

M&L for rendering 5mm thick in CM 1:3 on fair faces of brick work or concrete surfaces in ceiling, Complete all as specified and directed.

M&L for 15mm thick rendering on brick work or concrete surfaces in cement mortar 1:4 finsihed the surfaces fair and even Complete all as specified and directed.

M&L for preparing newly plastered or pointed surface of wall / ceiling and applying two coats of distemper oil emulsion over a coat of wall care putty complete all asspecified & directed by Engineer-in-charge.

M&L for three coats white wash on ceiling surfaces inclduing prepration of newly plastered and undecorated surfaces.

M&L for three coats white wash on wall surfaces inclduing prepration of newly plastered and undecorated surfaces.

M&L for two coats of cement base paint including preparation of newly plastered surfaces on walls, Complete all as specified and directed

M&L for one coat of white wash on wall undecorated surfaces including prepration of Old plastered surfaces.

M&L for one coat of white wash on ceiling undecorated surfaces including prepration surface, plastered or un plastered of Old undecorated surfaces.

M&L for one coat of oil bound distemper to old surfaces of walls after preparation complete all as specified.

M&L for one coat of cement base paint to old surfaces of walls after prepration complete all as specified.

M&L for 75mm thick PCC 1:3:6Type C-1 using 20mm crushed stone aggregate as in plinth protection and like finished even and smooth without using extra cement complete all as specified.

S&F for solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC Sheet reinforced with MS square tube in opening as per specification and drawing.

S&F for factory made soilid panel PVC Door shutter 30mm thick (Style) consisting of frame made out MS frame shall be covered with heat moulded wood grain printed PVC 'C' channel having PVC sheet stripof 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet used instead of Plain colour PVC sheet & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm used instead of exposed portion of PVC sheet beading as per specification and drawing.

S&F pressed steel frames,size 105x60mm for doors with one or more rebates including necessary lugs, butt hinges, lock strike plate etc. complete ,as specified.

Providing cement concrete type C-0 1:3:6 (12.5 mm graded agg) as for pressed steel chowkhats.Complete all as specified and directed.

S&F for 2nd class 35mm thick hard wood,Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces, and fitted to chowkats.

S&F for 25 mm thick flush shutter solid core construction, with block board core and plywood face panels,commercials type on both sides covered with decorative face veneer with lipping/frame to match complete all as specified.

M&L for two coats of synthetic enamel painting on wooden surfaces over a coat of pink primer including prepration of newly untreates surfaces.Complete all as specified and directed.

S&F for steel window 1.25 mm thick box type (primer coated) ERW hollow P section of size 60mmx25mm single rebated comprises glazed skeleton shutter ERW sec 50mmx20mm and 1mm thick with two openable leaf consisting two Nos sash bars of T-section 20mmx3mm complete welded to frame with one verticle mulion of ERW box type T-section of size 60mmx25mm and 1.25mm thick incl cutting holes and making good dismantled portion PCC (1:2:4) type B-1 four Nos for each window) including following fittings welded to frame shutter: - (a) Hold fast, 150mm long of 12mmx3mm made to shape-04 Nos per window. (b) Handle of z section 20mmx25mm, 100mm long 01 Nos per leaf (c) MS tower bolt 150mm long-2 Nos per leaf (d) z section 20mmx25mm, 100mm long stopper - 01 No per leaf (f) MS pintal hinges of size 75mmx12mm- 2 Nos per leaf (g) Fabrication & fixing arrangement as per Drg No CEJZ/TD-06/07. Note: Glass and painting shall be measured & paid separately under appropriate item.

S&F for mild steel framed work such as guard bars/grills,grating etc with end of bars shouldered and/or riveted or forged into spikes and similar works including one shop coat of zinc chromate primer complete all as specified.

S&F for 4mm thick sheet glass, ordinary quality and glazing with oil putty in square n. exc 0.5 sqm each panes complete all as specified

M&L for painting two coats of synthetic enamel paint including preparation of new steel surfaces of any description over 10cm in width or grith not other wise described. Complete all as specified and directed.

S&F for 150mm aluminium anodised barrel tower bolts of extruded section and fixed.

S&F for 250mm aluminium alloy anodised sliding bolts with hasp, staple and fixing clips of sheet, cast or extruded section fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed.

S&F for butt hinges, 100mm medium weight, cold rolled mild steel.

S&F for 125mm aluminium handles, cast type , anodised.

Demolition brick work or stone/boulder masonary, built in cement mortar or cement lime mortrar incl all qupins, arches, pillars, etc,but incl. ashlar fencings, dressed stone works and precast concrete articles.

M&L for brick work with sub class B brick straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 all as specified and directed.

All as per item No 45 but except bricks.

Demolition of mud in roofs, any thickness, incl plastering and leeping (whether full thickness removed or only part thereof), and removing from out side of defence land complete all as specified and directed.

Dismantling of brick tiles laid on mud mortar and jointed and pointed in any cement mortar including any treatment on roof complete all as specified and directed.

M &L for PCC 1:2:4 type B-0, 12.5mm graded graded aggregate as roof padding concrete to bring the extg slab in slope of 1:40. complete all as specified.

M&L for 15mm thick rendering on terrace, sides of parapet in cement mortar 1:4 with water proofing compound , finished even and fair.(Note water proofing compound will be measured and paid separately under other item.

Supply only integral water proofing compound.

M&L for cleaning the new plastered surfaces with wire brushes, brooms etc and applying a priming coat of bitumen primer @ 0.30 ltrs/Sqm consisting of 3/4 part bitumen of grade 85/25 and 1/4 part of kerosene oil.Complete all as specified and directed.

M&L for providing APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/Sqm ) land on after applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2Kg per Sqm by Torched application complete all as specified.

M&L for 40mm thick brick tiles laid on 15mm thick cement mortar 1:6 and joints grouted flush in cement mortar 1:3 mixed with 5% of crude oil by weight of cement,Complete all as specified and directed.

All as per item No.54 but except tiles after cleaning and removing old mortar from bricks

M&L for flush pointing to brick laid flat or brick tiles in paving cement mortar in 1:3 complete all as specified.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) in roof kerbs or mud stops, benching rounded or chamfered on edges complete.

S&F in repairs stop valves 20mm, cast copper alloy, screwed down, high pressure with crutch or butterfly handle etc complete fixed.Complete all as specified and directed.

Taking up or down steel tubing 15mm bore and connections, including cleaning for refixing or removal to store,Complete all as specified and directed.

All as per itme No 59 but 20 mm bore.

S&F for 15mm GI tubes, medicum grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors.Complete all as specified and directed.

All as per item No 61 but 20mm bore.

S&F in repairs PVC valve less, syphonic action type low level flushing cistern of capacity 10 Ltrs with inlet, ball valve, float and handle and fixed to IWC on existing brackets, .Complete all as specified and directed.

S&F in repair vitreous china washbasin, white, flat back, size 550 x 400mm, fixed on existing brackets incl 32mm bore CP waste coupling, waste pipe and incl provn of 15 mm bore fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with or without lettered hot or cold with long screwed shank and fly nuts etc.

S&F for viterous china squatting pan orrisa pattern , size 580x 440mm white, interged foot rest including connection to trap and to flush pipe, anti syphonic pipe etc complete making good to floor

S&F for vitreous china urinal, partition white of size 310X770mm fixed complete as directed.

M&L for vitreous china urinal,bowl type size of 465x335x265mm (back or corner wall type) complete incl providing and fixing plugs beding urinal against wall in cm 1:2 security urinal plug with and incl 60mm long brass screws pointing around urinal back in cement fixing automatically flushing cistern with bracket, flush pipes grating and union for discharge pipe fixed complete.

S&F for 15mm bore stop valve/angle valve cast copper alloy chromium plated fancy type screwed down, high pressure, with crutch or butter fly handles fixed in repairs.

S&F for PVC connections 15mm size with PTMT nuts of length 450mm

S&F for rotational moulded polyethylene water storage tanks 500 ltrs (Cylindrical vertical with closed top ) hoisted and fixed in position including 20mm bore high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed (Min wt 210 grams) complete including dismantling of existing water tanks and removing to store complete all as per specified in SSR Pt-1.

Taking down eaves gutters and rain water pipes (any size or pattern), Cast iron said, waste and vent pipes including all fittings,heads, shoes, bends, swan-necks, etc. all as speicified and directed by Engineer in Charge

S&F for 110mm bore PVC (SWR) bends any radius complete all as specified and directed by engr-in-charge.

S&F for 75mm bore PVC (SWR) bends any radius complete all as specified and directed by engr-in-charge.

S&F for 110mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by engr-in-charge.

S&F for 75mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engr-in-charge.

M&L for PVC (SWR) floor trap, plain with grating 75mm diameter of outlet, setting and jointing with solvent cement complete.

M&L for PVC (SWR) 'P' trap, 110mm diameter of outlet, setting and jointing with solvent cement complete.

M&L Endura chequered cement concrete tiles 30cmx 30cmx 10mm thick,set, jointed & pointed in neat cement slurry in floors with grey cement and pigments over & including 20mm thick screed in cement mortar 1:6

Taking down curtain rods along with wooden pallmate laid on wall.

S&F in repair curtain rod made out of 25mm dia(outer dia )pipe having thickness 0.63mm , PVC coated and colour/pattern, over all dia 28 to 29 mm complete all as specified and directed.

S&F for plastic finial of 28 to 29mm bore, decorated type, of any colour/pattern, best quality to suit the curtain rod and fixed at the end of curtain rod with suitable adhesive complete all as specified and directed.

S&F for mild steel prepainted bracket to hold the curtain rod and fixed to wall(Concrete/brick masonry) with the help of 2 Nos 50mm long steel screws and rawl plug included drilling with electric drill and making good the disturbed surfaces complete all as specified and directed.

S&F for framed work as in doors or gates ,coolers stand of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings etc confirming to Fe 410-s . (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

S&F in repairs 15 mm bore bib taps fancy type chromium plated with crutch or butter fly handle screwed down, screwed for iron pipe or for brass ferrule.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile 0.11 Sqm but n.exc 0.18 Sqm, in neat cement slurry and pointed in white or coloured cement with pigment to match over 15mm thick screed bed in cement mortar (1:6) all as specified and directed.

Taking down carefully the point wiring (light, Fan, socket or power) complete, (incl fittings such as switches, sockets any type, ceiling roses, pandents, light fittings, etc for taking credit( credit for above items should be made as per conditions separately) and making good disturbed surface of walls floors etc. all as specified.

Taking down Ceiling fan, sealing cable end, dismantling blades from fan and keeping in safe custody for reuse at site and making good disturbed surfaces complete all as specified and as directed.

Refixing only ceiling fan and connecting up including provision sutiable of new down rod for ceiling fans,of cable from celling rose/ connector to fan all as specified and as directed.

M &L for point wiring complete with 1.5 sqmm single core PVC insulted FRLS cable 1100 volts grade multistranded copper conductor drawn through and including 20mm dia PVC rigid non metallic conduit with all accessories such as internal bend end caps etc complete concealed in walls/ceiling/roof/etc including provision of 1.5 Sqmm single core PVC insulated FRLS cable 1100 volts grade with multistranded copper conductor cable as earth continuity conductor, all as specified and as directed for the following :-

One light/fan point controlled by one, one way switch

One switch socket outlet point 5 Amps on independent board

One 3 Pin socket outlet , 5 Amps on the same board with other switch

All as per item No. 4 described here-in-before but with copper conductor cable FR LS 2.5 Sqmm for one 3 pin socket outlet, 15 Amps and including provision of 2.5 Sqmm PVC insulated copper conductor cable as earth continuity conductor on independent board.

Supply and fix for LED tube light fittings 1200 mm, 20W, 240V, 50Hz,rated input current- 0.070-0.110, rated input watt 20, oprating voltage range- 140-270, P.F- not less then 0.95, surge protection upto- 4Kv, IP20, THD shell be less then 10%, CCT- (k0)- 6500ANSI, higher energy saving decorative ultra slim square profile LED lighting fixture with extruded polycarbonate enviromental friendly, energy efficient complete all as specified and directed.

M & L for sub main wiring complete with 2 runs of 6 Sqmm single core PVC insulated FRLS cable 1100 volts grade multistranded copper conductor cable with 1 run of 6 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 25 mm or higher dia non metallic rigid PVC conduit and conduit accessories concealed in wall/Ceiling etc all as specified and as directed .

Supply and fix for TPN MCB DB 4 ways ,Double door with 415 Amps, Double door type complete all as specified and as directed .

Supply and fix for MCB TPN 63 Amp, 415 Volt , C- series, 50 Hz, breking capacity-10 kA complete all as specified and as directed .

Supply and fixing for factory made sheet metal enclosures SPN 8 way double door 240 v for DB,s suitable for having MCB flush with wall complete all as specified and directed.

Supply and fixing for MCB SPN 40 Amps 240 V, C- curve, 50 Hz, breking capacity-10 kA. complete all as specified and directed.

Supply and fixing for MCB SP 6-32 Amps240 V, C- curve, 50 Hz, breking capacity-10 kA . complete all as specified and directed

Supply and fix for ceiling rose surface type bakelite 65 x 50mm with three terminals complete all as specified and as directed

Supply and Fix for switch Piano,Flush type single pole , one way 5 Amp complete all as specified and as directed.

Supply and Fix for socket outlet 3 pin, 5 A flush Piano,Flush type complete all as specified and as directed.

Supply and Fix for switch Socket combenation 2 in 1 outlet 3 pin, 5 A flush type complete all as specified and as directed by Engr-in-charge

Supply and Fix for switch Socket combenation 2 in 1 outlet 3 pin, 16 A flush type complete all as specified and as directed.

S&F for fan regulator , flush stapped type ,electronic , single phase 230 volt complete all as specified and directed

M &L for earthing incl earth work complete with galvanised steel earth plate electrode 60cm X 60 cm X 6 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level with the top edge of electrode not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4mm dia means of bolts, nuts,check nuts and washers of galvanised iron and GI lead protected with protection pipe of GI light grade 15mm dia upto 3mtr above ground level along poles fixed with two clamps of 25mm 3mm flat iron and connected to running earth wire at top of poles and watering pipe 20mm bore of GI medium grade all as shown in electrical plate No 3 of SSR Part-I 2009 connected to earthing test point all as specified and direct and testing on completion including PCC 1:3:6 ) C-I cover and frame excavation and earth work etc complete all as specified in elect plate No 3 of SSR Part -I 2009 Note :- PCC Chamber shall be constructed at least 1.50 mtr away from on the earth pit electrode and pipe for watering shall be provided in slanting manner.

Taking down of any size of bldy security light fittings complete all as specified and directed.

Supply and fixing for bldg security light fitting LED 30/35 W LED made up of pressure die cast aluminium housing with potted isolated driver and high power LED and indl lenses, oprating range- 90V to 340V AC. , IP66 with high power LED lamp compete all as specified and directed.

Supply, laying and testing cable XLPE insulated, screened PVC bedded galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 50 sqmm 3.5 core complete all as specified and directed.

Excavation in trenches soft/loose soil not exceeding 1.5 m wide and not exceeding 1.5 m deep for laying of pipes/cables etc getting out and bottom surface to required gradient complete all as directed & specified

Returning filling in including spreading leveling watering and well ramming in layers each not exceeding 25 cm thickness complete all as specified and as directed

Removal of surplus spoil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed

Supplying, filling in trenches, spreading, leveling sand cushioning 8 cm below cable and 15 cm above the cable for under ground cable complete all as specified & directed .

M & L for old size sub class 'B' bricks,laid flat in trenches over the cable with length of brick perpendicular to the direction of the cable , adjacent/abutting each other complete all as specified

PREM CONSTRUCTION COMPANY

SHRI GANESH CONSTRUCTION CO.

M/s R.N Construction Co.

AGNIHOTRI CONSTRUCTIONS