REPAIRS TO STEEL DOOR SWTS FLOORING ROOFING WALLING AND MISC BR WORKS AT ME LINES AND COD DEPOT UNDER AGE BR EAST AT GE DEHU ROAD

Amount

Taking down existing steel gate/door heavy shutters from Sheds, with or without ball bearing, including covered plain/corrugated sheets, hold fast/hanging arrangement of any article, hasp and staple,re-erect/ refix in same position after carrying out necessary repairs/welding,including greasing, oiling, easening and applying one coat of synthetic enamel painting,completere push pull or manual type, area of shutter not exceding 10 sqm including using machinary/ crane or mannully complete all as directed by engineer-in-charge ( Note : supply and fixing of any article like hold fast/hanging arrangement of any MS article, strap, gate stop, bolts etc, plain or CGI sheets for iron gate if required will be measured separately except greasing and oiling and painting to gate shutter as directed)

Taking down existing rolling shutters, with or without ball bearing,including top cover, anchoring rod, hasp and staple re-erect/ refix in same position after carrying out necessary repairs/welding,including greasing, oiling, easening and applying one coat of synthetic enamel painting,completere push pull or manual type, area shutter not exceding 10 sqm complete all as directed by engineer-in-charge ( Note : supply and fixing of ball bearing, anchoring rod, any type of steel/ iron work and welding work if required will be measured separately,except greasing and oiling and painting to rolling shutter as directed)

Dismantling structural steel work including doors, gates, etc but excluding framed truss etc all as specified

Taking down/ Dismantling rolling shutters and S & F new steel rolling shutters, with or without ball bearing, as specified including top cover, anchoring rod , hasp and staple , erected in position as indicated, complete push pull or manual type of 1.00mm thickness of laths all as specified and directed

S&F in repair for Ball bearing for rolling shutters all as specified

M & L for framed work as in doors or gates of angle or other section with gusset plates, rails , braces, etc, complete, drilled for fixing of steel sheeting or other covering Doors, etc, to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering running rails and guides) and hanging; also fastening and fixing complete Fe 410-w, gde E-250 quality A

S & F for gate stops, balusters , brackets , gully traps gratings, railling,, frames, manhole covers, stop valve boxes etc , articles not exc 5 kg all as specifed

S & F for framed work of gusset plates, angles or tees with web and flanges cut to shape drilled and countersunk for screw, including bending and welding angles , as necessary , reveting etc, nor exceding 10 kg each article, conforming to FE 290 Gde E 165 all as specifed

S & F for hand made sliding bolts, hold fasts, wall ties, hooks, bands, straps, supports or stays, including bolts, heavy, for large gates, two way or three way straps, plate washeres and similar articles conforming to Fe 290 Gde E 165 all as specified

Dismantling MS works of any desc. not otherwise provided for complete all as specified.

S&F Rolled Sections as in main croos beams , hip and jack rafters; purlins, where connected to common rafter , posts etc. conf to Fe-410-w(gdeE-250 quality-A)

S&F Roof truss framed trussed etc incl distance piece , cleats with necessery welding works etc Fe 410-W ( gde E-250)Quality A

M &L for MS work as in wind tie or any other work incl cutting, drilling holes etc.

M&L for MS Plates (plain or chequrred) channels,square cut, notched chamfer or square cut or notched (ordinary and counter sunk) forming holes without any attachment with MS Gde Fe 410-0

M&L for mild steel screw bolts (machine made) with hexogonal or square heads at one end & screwed the other or screwed both ends each screwed end to be fitted with washers & one hexagonal or square nut, length of bolt n.exc 5 cm long, diameter of shank 11 mm to 15mm.

M & L for mild steel bolts purpose made with hexagonal or square head one end and screwed the other or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut exceeding 30cm long of dia of neck in mm exc 12 and not exc 20mm

Dismantling of Plain or corrugated steel sheeting (including translucent corrugated sheet), any gauge, thickness, including nainital or similar pattern, from roof/wall/ridge/valley gutter coverings of tin shed etc all as specified

S&F for 0.63mm thick, galvanised, corrugated mild steel sheeting with two corrugations side lap fixed with coach screws and washers, in roofs, walls etc, with grade of zinc coating 275 all as specified

S&F for 0.80mm thick, galvanixed, plain mild steel sheeting in ridges , hips, valley gutters, driip and straight flashings (length and girth as fixed) with grade of zinc coating 275 all as specified

S&F 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc all as specified

S & F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

All as per item No. 21 above but plain sheet fix in valley gutter / ridge

Cleaning of static water tank with using pumping set for dewatering and removing rubbish and debris, cleaning all dirt, all scales by using wire brush, and washing flashing with clean water entirely all as drected at site (size of SWT 3 to 5 m internal dia and 2 to 3.5 m depth)

Demolition of cement concrete ( un reinforced ) of any description and in any position not otherwise specifically provided for

M & L for providing PCC 1:4:8 type D2, (using 40mm graded stone aggregate) in foundations, filling and mass concrete all as specified

M &L for providing PCC 1:2:4 type B1,(using 20mm graded aggregate) in water troughs and the like including weathering , copings, kneelers, apex stones , bed plates , kerbs , chamfered angles and throating, including using 10% admixture of 'NITOBOND SBR' by weight of cement, from FOSROC or equivalent as directed and as per manufacturer instruction .

Taking down cement plaster of any description on brick or stone walls/concrete surfaces, including raking out joints, hacking for key, scrubbing down with water etc.

M&L for rendering 10mm thick in cement mortar 1:6 on Brick / conc. surfaces & finishing surface even & smooth without using extra cement.

M&L for rendering 15mm thick in cm 1:4 on Brick / conc. surfaces or surfaces other than fairface of brickwork with including using 10% admixture of 'NITOBOND SBR' by weight of cement, from FOSROC or equivalent as directed and manufacturer instruction including finished even and fair.

M&L rendering 15mm thick in cm 1:4 on Brick / conc. surfaces or surfaces other than fairface of brickwork with incl admixture of WPC 3% by wt of cement including finished even and fair.

Dismantling floor hearth or wall tilling incl cement mortar bedding and backing all as directed.

M/L for Coloured joint free Non skid ceramic tile 7 to 8 mm thk area of each tiles Exc 0.18 sqm & nexc 0.38 sqm as in floor set & jointed in neat cement slurry and pointed in white/colored cement laid over and including screed bed 15 mm thk in CM 1:6

M&L for glazed coloured ceramic tiles 300mm & 200mm x6 to 7 mm thick as in vertical surfces set & jointed in neat cement slurry & pointed in coloured cement incl backing coat 10mm thick in CM 1:4 all as direced.

M&L for glazed coloured ceramic tiles in vertical surface 350x250x7mm/ 450x350x7mm thick set and jointed in neat cement slurry an pointed in white or coloured cement to mach incl 10mm thick backing coat in CM 1:4 complete all as specified

M&L for non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.06 sqm but not exc 0.11 sqm in floors etc,, set and jointed in neat cement slurry and pointed in white or coloured cement to mach laid over and including screed bed 15 mm thk in CM 1:6 complete all as specified

Dismantling wall/ ceiling boards(fibre pulp insulation etc.) or insulations boards /slabs/blankets any thickness incl. cover fillets

S & F Anodised Alu. Snap grid 605x605 mm frame wk for false ceiling and providing 9mm th Acoustical board/tiles for insula-tion and accoustic purposes, 60x60 cm in size, fixed in celing with screws to frame work or with staples on snap grid including hangers 6 mm dia G.I. ( up to 1200 mm length ) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 X 3 mm size 60 mm long all as specified

Demolition of brick work/sone masonry built in cement mortar all as specified.

M & L for brick work with sub class "B" old size bricks straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 .

.-Ditto- As item 39 above but Except bricks

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar(for interlocking tile, cudappa & chequered tiles all as specified.

M&L for laying machine pressed precast concrete interlocking reflective coloured pavers block any shape and size confirming to IS 15658-2006 of 55mm to 60mm thick, M-35 Grade over and including 30mm thick sand layer spreaded all as specified.

M/L Chequered Cement Concrete Tiles 20 CM x 20 CM X 25 mm th set and jointed in cement slurry and pointed in neat grey cement & pigment in floors over and including screed bed 15 mm thk in CM 1:6.

M&L for machine cut Cuddappa stone stab 30 to 40mm thick one side polished laid & jointed with grey cement slurry mood with pigment to match the shade of slab including cutting & polishing complete.

Demolition of concrete ( un reinforced ) in ground floors and paving nexc 15 cm thk (below or above ground level)

M/L PCC 1:4:8 type D2 (40 mm graded stone aggregate ) 75mm thick as in sub base.

M&L for cement concrete type C 2, 1:3:6 (using 40mm graded stone aggregate as in surface channel and drain bed complete all as directed

Extra over for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as directed

M & L, applying two coats of oil bound distemper over one coat of primer and putty including preparation of newly plastered surfaces of walls complete all as specified and as directed.

M&L for preparing new plastered surfaces & applying two coats of cement base paint on walls.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer.

M&L for preparation old steel surface and aplying one coat of synthetic enamel paint complete all as specified and as directed.

Taking up or down steel tubes and connections bore of pipe 15mm.

All as per item No. 53 above but bore of pipe 20mm

M&L GI tubes, medium grade with all fittings and fixed complete to walls, ceiling or laid in floors, bore of pipe 15mm

All as per item No.55 above but bore of pipe 20mm

Refixing of old steel tubing and connections in new or old position (wall ceiling floor etc) after cleaning etc15 mm dia complete.

All as per item No. 57 above but bore of pipe 20mm

Dismantling water tanks of capacity n.exc. 500 ltrs complete.

M&L rotational moulded polythene water storage tanks, cyclenderical vertical with closed top, hoisted and fixed in position incl float valve 20 mm dia PTMT all as specified in SSR Part -I of capacity 500 ltrs.

Fixing only water tanks of capacity 500 Ltr incl cleaning and removing all scale and dirt etc from tanks and mouth of circulating pipes.

Cleaning and removing all scale and dirt , etc, from tanks and from mouths of circulating pipes etc . Exc 250 and not exxc 500 litre capacity

Cleaning and removing all scale and dirt , etc, from tanks and from mouths of circulating pipes etc . Exc 500 and not exxc 1000 litre capacity

M/S RENUKA CONSTRUCTIONS

H S TAKHI

RAMESH PATIL

TUSHANT CHOUDHARY

Dinesh Constructions

PREETI ENTERPRISES

M/S B.A. GAIKWAD

Santhi Enterprises