Construction of 40 additional SPS Class rooms in Existing Premises of Sarvodaya, Vidyalaya Mansarover Garden New Delhi School ID 1516003 SH Manufacturing Supplying and Installing school furniture for new school building

Amount

Dual Desk :- W 1066mm x D 830mm x H 760/452mm Providing, placing/installing of Dual Desk manufactured to the specification provided below - The overall dimensions of desk will be W 1066mm x D 830mm x H 760/452mm complete as per drawing and direction of Engineer-in- charge having the following specifications:- (a) Side frame structure: Made of prime quality CRCA pressed form section 165mm x25mm x 1mm thick welded to 25mm x 50mm x 1.2mm thick CRCA tube 830mm length. Seat and back side frame structure also made of prime quality CRCA pressed form section 165mm x 25mm x 1mm thick welded to 25.4mm diameter x1.6mm thick ERW -1 pipe. All 8 nos. horizontal supports are 25mm x 25mm x 1.2mm thick shall be CRCA tube. Rectangular tube 50 x 25 x 1.2mm thick should be closed with CRCA welded Sheet both sides and The back pipe dia. 25.4 x 1.6mm thick should be closed with metal process with end sealing machine (Back side) and other side (Under the seat) PPCP cap complete as per drawing. (b) Front panel cum tray shall be made of prime quality 0.8mm thick CRCA sheet of H 150mm x W 1012mm x D 250mm to 300mm with middle partition and side stiffeners of MS CRCA tube size 19mmx19mmx1mm thick. One vertical support (partition) of square tube size 25mm square x 1.2mm thick must be provided at centre of tray and Front Face must be embossed as per drawing. (c) Additional front panel prime quality 0.8mm thick CRCA sheet of size H 150mm x W 1012mm X D 21mm with square perforation. CRCA Tube of size 19 x 19 x 1 mm thick to be inserted for full length at bottom of Jali as shown in Drg. (d) Desktop, seat and back shall be made of IS: 303, 18mm thick plywood of MR grade having AA types of surfaces of OSL (one side 0.6mm thick lamination and one side balancing) and three edges must be sealed with 2mm thick PVC edge banding tape with hot melt glue standard ‘D4499 Jowatherm -280’ on through feed edge banding machine. Edge band must be trimmed on edges and corner, Sizes are below:- 1. Seat W 1066mm X D 260 mm. 2. Desktop W 1008mm x D 338 mm 3. Back 1066mm x D150 mm 4. One long edge of Desk top, seat & back shall be post formed with round edge. (e) Desktop must be fitted with M6 sunken bolt 3 nos. size M6 x35mm length Zinc plated from Top side, maximum distance 40mm from desktop edge and 3 nos. MS Zinc plated screw self-tapping size dia. 4mm x 38 length again from Bottom side (f) Seat and back each must be fitted with 6 nos. MS screw Zinc plated self-tapping size dia. 4mm x 38 length from Bottom side (g) Hooks made of MS wire dia. 5mm and size W 23mm, D 32mm and H80mm must be provided on inner side of vertical pressed formed steel section on both sides (h) (i) All Pipes shall be of ERW-1, IS: 3074-2005/ IS: 4923 and CRCA sheet, IS -513 CR-2 Designation- Grade D). (ii)All MS. CRCA parts must be MIG, TIG or spot welded as per technical requirement (i) All steel components must be powder coated process should be conveyored continues flow to oven and temperature control in oven with thermostatic system. The thickness of desk should be minimum 50 microns dry film thickness(DFT) after 8 tank pre-treatment process flow using Hankel make chemical i.e. Degreasing (1st tank),Water rinsing (2nd tank), Derusting (3rd tank),Waterrising(4th Tank), Activation (5th Tank), Phosphating (6th Tank),Water Rinsing (7th Tank),Passivation (8th Tank)and dipping should be PLC control line through mechanical transporter The parameter temperature should be displayed at every tank. Passivation (8th Tank) (j) School name must be painted on back side of the back rest and text height will be 25mm (k) PPCP virgin material Shoes of approved quality must be providing in the bottom of frame - 4 nos.

Dual Desk :- W 1066mm x D 830mm x H 705/400mm Providing, placing/installing of Dual Desk manufactured to the specification provided below - . The overall dimensions of desk will be W 1066mm x D 830mm x H 705/400mm complete as per drawing and direction of Engineer-in- charge having the following specifications:- (a) Side frame structure: Made of prime quality CRCA pressed form section 165mm x25mm x 1mm thick welded to 25mm x 50mm x 1.2mm thick CRCA tube 830mm length. Seat and back side frame structure also made of prime quality CRCA pressed form section 165mm x 25mm x 1mm thick welded to 25.4mm diameter x1.6mm thick ERW -1 pipe. All 8 nos. horizontal supports are 25mm x 25mm x 1.2mm thick shall be CRCA tube. Rectangular tube 50 x 25 x 1.2mm thick should be closed with CRCA welded Sheet both sides and The back pipe dia. 25.4 x 1.6mm thick should be closed with metal process with end sealing machine (Back side) and other side (Under the seat) PPCP cap complete as per drawing. (b) Front panel cum tray shall be made of prime quality 0.8mm thick CRCA sheet of H 150mm x W 1012mm x D 250mm to 300mm with middle partition and side stiffeners of MS CRCA tube size 19mmx19mmx1mm thick. One vertical support (partition) of square tube size 25mm square x 1.2mm thick must be provided at centre of tray and Front Face must be embossed as per drawing. (c) Additional front panel prime quality 0.8mm thick CRCA sheet of size H 150mm x W 1012mm X D 21mm with square perforation. CRCA Tube of size 19 x 19 x 1 mm thick to be inserted for full length at bottom of Jali as shown in Drg. (d) Desktop, seat and back shall be made of IS: 303, 18mm thick plywood of MR grade having AA types of surfaces of OSL (one side 0.6mm thick lamination and one side balancing) and three edges must be sealed with 2mm thick PVC edge banding tape with hot melt glue standard ‘D4499 Jowatherm -280’ on through feed edge banding machine. Edge band must be trimmed on edges and corner, Sizes are below:- 1. Seat W 1066mm X D 260 mm. 2. Desktop W 1008mm x D 338 mm 3. Back 1066mm x D150 mm 4. One long edge of Desk top, seat & back shall be post formed with round edge. (e) Desktop must be fitted with M6 sunken bolt 3 nos. size M6 x35mm length Zinc plated from Top side, maximum distance 40mm from desktop edge and 3 nos. MS Zinc plated screw self-tapping size dia. 4mm x 38 length again from Bottom side. (f) Seat and back each must be fitted with 6 nos. MS screw Zinc plated self-tapping size dia.4mm x 38 length from Bottom side (g) Hooks made of MS wire dia. 5mm and size W 23mm, D 32mm and H80mm must be provided on inner side of vertical pressed formed steel section on both sides. (h) (i) All Pipes shall be of ERW-1, IS: 3074-2005/ IS: 4923 and CRCA sheet, IS -513 CR-2 Designation- Grade D). (ii) All MS. CRCA parts must be MIG, TIG or spot welded as per technical requirement (i) All steel components must be powder coated process should be conveyored continues flow to oven and temperature control in oven with thermostatic system. The thickness of desk should be minimum 50 microns dry film thickness(DFT) after 8 tank pre-treatment process flow using Hankel make chemical i.e. Degreasing (1st tank),Water rinsing (2nd tank), Derusting (3rd tank),Waterrising(4th Tank), Activation (5th Tank) ,Phosphating (6th Tank),Water Rinsing (7th Tank),Passivation (8th Tank)and dipping should be PLC control line through mechanical transporter The parameter temperature should be displayed at every tank. (j) School name must be painted on back side of the back rest and text hieght will be 25mm (k) PPCP virgin material Shoes of approved quality must be providing in the bottom of frame - 4 nos.

Table with Side Unit Providing, supplying and Placing Principal Table with Main table of overall Size 1800mm(L) x 900mm(D) x 750mm(H), Joining table of size 1050w x 1200 D x 750H Side Table of size 1200mm(L) x 600mm(D) x 730mm(H) and Drawer Unit of size 400mm(W) 560mm(D) 560mm(H). The Main Material of the table is MDF Board .Surface : CPL (Continuous Pressure Laminate) in 0.6 mm thickness. Post forming should be done to make approved profile of required colour. Edging : 2 mm PVC Edging, matching colour with hot melt glue at 200°C Main Desk Table Top + Joining Top 25 mm MDF, plus 30 mm MDF (Medium Density Fiberboard) black pad. Modesty Panel: 18 mm MDF. Leg : 25 mm MDF, plus 30 mm MDF right and left pad i/c vertical post as per manufacturers specification Side Table : Table Top Exterior grade shall be made of 25mm thick MDF. Metal Black Spacers of Diameter 4cm, Length 10.4cm. Pedestal Leg : 25 mm MDF Drawer Unit : Top Panel : 25mm MDF. All Other Panels : 18 mm MDF. Lock : Provided. Castor: Provided. Handle: Metal. All the above items should be as per photo, sketch, specifications& direction of Engineer-in-charge.

library tables/Student Work Table Providing, supplying and placing library table/Student Work Table of overall size 1800mm(L) x 900mm(D) x 740mm(H).The worktop of the table shall be made from 25 mm thick MDF Board ( Exterior grade) with 2mm thick PVC edging matching colour with hot melt glue at 200°C open edges of work top. Understructure of the table comprises C-Frames of 1.6 mm thick M.S CRCA with Powder coating upto 40-50microns. C-frame 75mm for supporting the Top & 75mm long recess for 4 No legs of Diameter 38.1mm x 1.6 mm thick M.S ERW tube with powder coated shall be provided. The detachable legs shall be duly screwed with C- frame and recessed . (All the corners should be rounded not shown in picture.) All the above items should be asper photo, sketch, and specifications & direction of engineer-in-charge.

Teachers Table/Instructor's Table Providing, supplying and placing Teachers Table/Instructor's Table of size 1200mm(L) x 600mm(D) x 725mm(H). Worksurface of the table shall be made from 18mm thick Pre Laminated wooden Ply (Lami Ply, MR grade as per IS:303) with decorative lamination(0.8mm thick) on both sides for top. All work surface edges are duly sealed with 2mm thick PVC edging of matching colour with hot melt glue at 200°C. Understructure of the table comprises Rectangular Frames Fabricated from 1.2mm thick Cold Rolled Close Annealed (IS:513), Finish of metal parts - Powder coat (Epoxy polyester). Leg and one foot rest between the base and vertical wire carrier should be Fabricated component from 38mm x 25mm x 1.2mm thick MS ERW Tube (IS:7138) with Powder coat (Epoxy polyester). Modesty panel shall be 0.8mm Thick CRCA Sheet duly poweder coated. One Side Panel made from 0.8mm thick CRCA (IS:513). Wire Carrier shall be provided, Vertical Wire Carrier along with Drawer made of 0.8mm Thick CRCA Grade D as per IS:513 and Horizontal Wire carrier under the worktop made of 0.8mm thick CRCA Grade D as per IS:513 complete powder coated. Finish: Powder coat (Epoxy polyester), Plastic Cap for Cable travel should be Injection Moulded Polypropylene. Leveler glide for Leg of Nylon 6 & MS Bolt. Drawer Unit with 3 Drawers shall be provided of size 670mm(H) X 550mm(D) X 350mm(W), Shell, drawer tray, Drawer Front, Frame Assembly of the drawer unit shall be made of 0.8mm thick CRCA (IS:513) with Powder coat (Epoxy polyester). 10 lever cam Lock shall be provided for locking. Handle shall be made from Injection Moulded Polypropylene & Leveler of Nylon6 & MS Bolt. All the above items should be as per photo, sketch specifications & direction of engineer-in-charge.

Principle Chair Providing, supplying and Placing in position High Back Chair. The seat shall be made of 1.4 +/-0.1 cm thick hot pressed plywood upholsterd with fabric and moulded polyurethane foam. It shall have seat depth adjustment of 5.0 +/- 0.3cm integrated in the seat through a sliding mechnism. Seat size shall be 50.0cm(W) x 49.0cm(D). The back shallbe injection moulded in glass filled polyamide which shall be upholstered with mesh fabric. The back shall consist adjustable lumbar support made of injection moulded polypropylene having an adjustment of 6.0 +/- 0.1 cm. Back size shall be 50.0 cm W x 68 .0 cm H. The polyurethane foam for seat shall have a density of 55 +/- 5 kg/m³. The height adjustable armrest shall be made of polyamide structure and polypropylene housing with moulded PU armtop having an adjustment of 7.0 +/- 0.3 cm. The mechanism shall be dsigned with following features -: 360º revolving type, Centre Tilt Syncro Mechanism, 3 position (inclusing upright lock) giving option of variable tilt angle to the chair with anti shock feature. The headrest shall be injection moulded in glass filled polypropylene which shall be upholstered with foam and fabric. It shall have an adjustment of 6.0 +/- 0.1 cm and it shall be assembled over the full back chair. The Headrest shall be provided with a provision of Coat Hanger. The pneumatic height adjustment shall have an adjustment stroke of 8.5 +/- 0.3 cm. The pedestal shall be High pressure Die cast aluminium and fitted with 5 nos. of twin wheel castors. The pedestal shall be 65.0 +/- 0.5 pitch centre dia. The twin wheel castors shall be injection moulded in black glass filled polyamide having 6.0 +/- 0.1 wheel dia. All the above item should be as per photo, sketch and specifications & direction of engineer-in-charge.

Principle Visitor's Chair Providing, supplying and placing in position Principal Visitor Chairs. Chair Seat and Back assembly shall be made up of 1.2+/- .2 cm thick hot pressed plywood, upholstered with fabric and moulded Polyurethane foam together with moulded seat and back covers. The Seat is provided with a pre-moulded inserts at the bottom for fixing Mechanism and Armrests. The back foam is designed with contouredl lumbar support for extra comfort. Back size: 50.0cm(W) x 49.0cm(H) Seat size: 50.0cm.(W) x 46.0cm(D) The polyurethane foam shall be moulded with density = 60 +/-2 kg/m3 and Hardness = 20 +/- 2 at 25% compression. Seat and back cover provided shall be made of injection moulded in black co-polymer polypropylene vacuum formed from ABS sheets. ARMRESTS : The one piece armrests made of black integral skin polyurethane with 50-70 Shore 'A' hardness and reinforced with M.S. Insert. The armrests are scratch and weather resistant. The armrests are fitted to the seat. The understructure is tubular frame in cantiliver type and made up of dia 2.54cmx0.2cm thick MS ERW tube and black powder coated. (DFT 40-60 microns). All complete as per manufacturers specification, approved sample and direction of Engineer-in-Charge.

Teacher chair/Chairs Providing, supplying and placing of Teacher Chair/Chairs. The Seat and Back Assembly shall be made up of 1.2cm thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam. The Seat is provided with a pre-moulded inserts at the bottom for fixing Armrests. The back foam is designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. BACK SIZE : 47.5cm(W) x 58.0cm(H) and SEAT SIZE : 47.0cm(W) x 48.0cm(D). The Polyurethane foam is moulded with density =60 +/-2 kg/m 3 and Hardness = 20 +/- 2 at 25% compression. ARMRESTS: The one-piece armrests are injection moulded from black Co-polymer Polypropylene. TUBULAR FRAME : The powder coated tubular frame is cantilever type & made of dia 25.4mm x 2mm thick M.S. ER.W. Tube as per sketch for item. All the above items should be as per photo, sketch ,specifications& direction of engineer-in-charge.

Sofa Set(3 +1+1) Providing, supplying and placing sofa set(3+1+1). 3 Seater sofa having overall size of 1750mm(L) x 870mm(D) x 730mm(H) and 1 Seater Sofa having overall size of 920mm(L) x 870mm(D) x 730mm(H) and Seat Height of 390mm upholstered with Synthetic leather with seasoned solid wood frame material of size 50mm x 50mm, Seat of PU foam with foam density of 28 Kg/cubic cm and Back Foam density of 22 kg/cubic cm and ( 150mm thick) webbing material Nylon of 50 mm thickness including springs hassen cloth, cotton. Hard wood facia 18mm thick solid wood is to be provided on the Arm facia. All the above items should be as per photo, sketch , specifications & direction of engineer-in-charge.

Lockers Providing, placing/installing of Lockers manufactured to the specification provided below - OverallSize : 1150mm(W) x 600mm(D) x 1830mm(H). Construction : Rigid knockdown construction. Material : CRCA 0.8 mm Thickness. Locking : 10 Lever Cam Lock arrangement. Shelf Uniformly Distributed Load Capacity per each shelf level is 35 Kg maximum. Finish : Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10).Handle / Label holder • Aesthetically appealing Snap fit ABS plastic handle. Plastic label holder for identification. Ventilation Attractive punched pattern for ventilation. . All the above items should be as per photo, sketch and specifications & direction of engineer-in-charge.

Classroom Almirah Providing and Placing in position Storage Unit for Classroom of overall size 1000mm(W) x 500mm(D) x 2025mm(H) including levellers. The storage unit shall be divided into 2 parts of 500mm(W) each by a vertical partition of 1980mm(H). The storage units shall be stacked widthwise to form a row of storage having a common side panel. The construction of the storage units shall be aesthetically appealing and knock down or welded. Legs shall be fitted in the floor units with screw type leveller and material shall be from combination of CRCA sheet of 0.8mm thick. The storage units shall be provided with height wise adjustable 4 shelves mounting with slots of pitch 25.4mm from top to bottom at all internal corners in classroom almirah , each shelf shall have a load capacity of 40 kg Uniforming Distributed Load. The storage will have steel 2 Nos Hinged Door with kunckle hinges and individual lock for each door. Each door shall be provided with a handle Ergonomically designed with Aesthetically appealing made from Aluminiumdia cast mazakhandle. The complete floor units shall be provided with 3 way locking and thickness of rod shall not be less than 8 mm and Finished with Epoxy Powder coated to the thickness of 50 microns(+/-10). All the above items should be as as per photo, sketch and specifications as per the direction of engineer-in-charge.

Wall Mounted Storages Providing and placing Wall Mounted Storage Units with Metal Body and Wooden Shutters. Storage Cabinets to be of complete modular design Consisting of Cabinet Frame, Wooden shutters, shelves and stainless steel D shape S.S handles. Cabinet frame to be of 0.8mm +/- 0.07mm CRCA MS sheet as per IS-513 with Horizontal Stiffners made from 1.2mm +/- 0.09mm thick CRCA as per IS-513. Wooden Shutters are made from 18mm+/-0.5mm thick exterior grade Pre-Laminated Particle Board as per IS specifications. All the edges of the door are duly sealed with 2mm thick PVC Edge Banding. Height wise 1No CRCA adjustable shelf shall be provided in each storage having a load carrying capacity of 25kg UDL. Hinges to be spring loaded with CED coating with soft closing mechanism. The complete M.S. material of cabinet to be pretreated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat to be 50 +/-10 microns(minimum) as per specification. Each unit should have a locking facility with 10Lever cam lock mechanism. One no. sheet of required size provided inside the storage unit end to end to provide smooth surface inside the storage. All the above items should be as per photo, sketch specifications & direction of engineer-in-charge. (a) Storage Unit of size 600mm(W) x 325mm(D) x 750mm(H)

Wall Mounted Storages Providing and placing Wall Mounted Storage Units with Metal Body and Wooden Shutters. Storage Cabinets to be of complete modular design Consisting of Cabinet Frame, Wooden shutters, shelves and stainless steel D shape S.S handles. Cabinet frame to be of 0.8mm +/- 0.07mm CRCA MS sheet as per IS-513 with Horizontal Stiffners made from 1.2mm +/- 0.09mm thick CRCA as per IS-513. Wooden Shutters are made from 18mm+/-0.5mm thick exterior grade Pre-Laminated Particle Board as per IS specifications. All the edges of the door are duly sealed with 2mm thick PVC Edge Banding. Height wise 1No CRCA adjustable shelf shall be provided in each storage having a load carrying capacity of 25kg UDL. Hinges to be spring loaded with CED coating with soft closing mechanism. The complete M.S. material of cabinet to be pretreated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat to be 50 +/-10 microns(minimum) as per specification. Each unit should have a locking facility with 10Lever cam lock mechanism. One no. sheet of required size provided inside the storage unit end to end to provide smooth surface inside the storage. All the above items should be as per photo, sketch specifications & direction of engineer-in-charge. (b) Storage Unit of size 750mm(W) x 325mm(D) x 750mm(H)

Bookcase Providing and placing in position 4 Door Bookcase of size 910mm(W) x 320mm(D) x 1740mm(H). It has Rigid Knock down construction and Prime Quality CRCA Steel -Top, Back & Side Panels shall be made from 0.7mm high yield strength CRCA & rest in 0.8mm CRCA. Each Door has 6 Lever Cam lock with common key. Each Door has 3mm thick transparent glass for clear inside vision secured in a Metal Frame through rubber gasket. Each door shall have a Scissor mechanism for receding inside the top of respective compartment & ensures parallel & smooth movement. Each door shall have plastic side end caps as Handle which shall be for easy to grip, each compartment shall have a storage shelf with Uniformly Distributed Load Capacity per each shelf shall be 40 Kg maximum. The finish shall be Epoxy Polyester Powder coated to the thickness of 50microns (+/-5 micron). All the above items should be as as per photo, sketch and specifications as per the direction of engineer-in-charge.

Modular Workstations Providing, placing/installing of Modular Workstation manufactured to the specification provided below - The understructure of the workstation comprises of Powder Coated Leg Assemblies, Cross connectors. On the matrix of Legs and Cross connectors, the Work-surfaces are fixed. Table Legs are fabricated by rectangular holo tubes by CO2 welding MS ERW Tube 50mm x 50mm x 1.2mm thick (as per IS: 7138 ERW). The base of the MS tube is fitted with a Glide plate over which an M8 Leveler is fitted, which allows for adjustment of the height by 10mm and coated with minimum 45 micron thickness of epoxy powder coating. Worksurface made of exterior grade of approved shade made from 25mm thick Pre-Laminated MDF Board conforming to IS specifications of approved shade. All the edges of work surface shall be provided with machine pressed 2mm thick PVC lipping glued with hot melt EVA glue. The worktop shall be provided with a 50mm Dia Grommet cut-out for wire management and a horizontal wire carrier fitted below the worktop to carry wires along the length of the workstation. The wire carrier is made with a combination of 3mm and 5mm MS Rod (IS: 9550 Bright Bar) along with 5mm thick MS Plate (IS: 2062, 5mm HR) duly powder coated of required length or as per manufacturer’s specifications. The workstation shall be provided with a full length (end to end) Fabric screen of 450mm(H) x 23mm Thick made of Plain Particle board uphostered with Fabric fitted in a aluminum extrusion (HE-9, IS : 63400) frame. The screen assembly is fitted to the Understructure and worktop by brackets made of 3mm thick MS Plate (IS:2062 3mm HR) which are fabricated by welding. The bracket is powder coated matching to the colour scheme of understructure. All the above items should be as per photo, sketch specifications & direction of engineer-in-charge. (a) Workstation of size 1200mm(L) x 600mm(D) x 1200mm(H) with Worktop Height 750mm

Modular Workstations Providing, placing/installing of Modular Workstation manufactured to the specification provided below - The understructure of the workstation comprises of Powder Coated Leg Assemblies, Cross connectors. On the matrix of Legs and Cross connectors, the Work-surfaces are fixed. Table Legs are fabricated by rectangular holo tubes by CO2 welding MS ERW Tube 50mm x 50mm x 1.2mm thick (as per IS: 7138 ERW). The base of the MS tube is fitted with a Glide plate over which an M8 Leveler is fitted, which allows for adjustment of the height by 10mm and coated with minimum 45 micron thickness of epoxy powder coating. Worksurface made of exterior grade of approved shade made from 25mm thick Pre-Laminated MDF Board conforming to IS specifications of approved shade. All the edges of work surface shall be provided with machine pressed 2mm thick PVC lipping glued with hot melt EVA glue. The worktop shall be provided with a 50mm Dia Grommet cut-out for wire management and a horizontal wire carrier fitted below the worktop to carry wires along the length of the workstation. The wire carrier is made with a combination of 3mm and 5mm MS Rod (IS: 9550 Bright Bar) along with 5mm thick MS Plate (IS: 2062, 5mm HR) duly powder coated of required length or as per manufacturer’s specifications. The workstation shall be provided with a full length (end to end) Fabric screen of 450mm(H) x 23mm Thick made of Plain Particle board uphostered with Fabric fitted in a aluminum extrusion (HE-9, IS : 63400) frame. The screen assembly is fitted to the Understructure and worktop by brackets made of 3mm thick MS Plate (IS:2062 3mm HR) which are fabricated by welding. The bracket is powder coated matching to the colour scheme of understructure. All the above items should be as per photo, sketch specifications & direction of engineer-in-charge. (b) Workstation of size 1500mm(L) x 600mm(D) x 1200mm(H) with Worktop Height 750mm

Laboratory Work Bench - Sink Unit Providing, placing/installing of Sink Unit manufactured to the specification provided below - size 600mm(W) which shall comprises of Sink Cabinet, Polypropylene Sink Unit and 1-Way Goose Neck 360 Degree revolving Faucet.as per followingSink CabinetSink cabinet. :- The Sink cabinet shall be Welded body with load bearing members such as top, bottom and stiffeners made of 0.8mm thick CRCA Sheet. The cabinet unit shall be provided with Pair of Shutters. Shutter has a sandwich construction with profile as a sound dampener. The complete unit shall be epoxy powder coated with thickness of 40-60 microns and is suspended from tubular understructure, with an overlay shutter. The cabinet has a corrosion resistance magnetic strip as shutter catch. Shutter shall be provided with semi recessed handle and five knuckle overlay hinge (SS-304) with 270 degree opening. Cabinet fixing brackets of 2mm thickness. The cost of sink cabinet does not includes the cost of basic understructure as the cost of understructure shall be paid in Item No 1.All the above items shall be as per photo, sketch specifications & direction of engineer-in-charge.b. Polypropylene Sink AssemblyProviding and fixing Polypropylene Sink with PP Waste, Anti-Siphon Bottle Trap & Flexible Drainage Pipe. Sink bowl shall be Polypropylene Molded made up of 5mm thick high density and elastic poly propylene with good resistance to organic solvents. Standard bowl size shall 600mm(L) x 400mm(W) x 300mm(D).c. 1 Way Water FaucetProviding and fixing 1-Way 360 Degree Revolving Water Faucet. Faucet fittings shall be laboratory grade. Water faucet and valve bodies shall be cast red brass alloy or bronze forgings, all fittings shall be powder plated. Brass as per IS:319, Pipe as per : IS:407,Outlet nipple in PP construction. PP knob to be used. All gasket and O-ring of Nitrile Rubber make. Inlet connection 1/2" BSP. Gooseneck spout with 360 degree rotation with 500000 life cycles. Pneumatic test at 250 psi, hydraulic test at 125 psi, bursting test at 500 psi. Coating to be glossy epoxy fusion bond. The Faucet shall be fixed to the existing water outlet by providing PVC connection with brass unions of required length. All the above items shall be as per photo, sketch specifications & direction of engineer-in-charge.

GEEKEN SEATING COLLECTION PVT LTD (BID ID -1637938)

Methodex Systems Pvt. Ltd. (BID ID -1640687)