ADDN ALTN AND SPECIAL REPAIRS OF SELECTED OLD MD ACCN AT JAMNAGAR MIL STN

Amount

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L Vitrified ceramic tiles light shade 9-10 mm thick (square/rectangular) polished, area of each tiles n exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L Vitrified ceramic tiles light shade 9-10 mm thick (square/rectangular) polished, area of each tiles n exc 0.36 sqm in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10 mm thick backing coat in CM 1:3 complete all as specified and directed.

M&L coloured, joint free, Non-skid ceramic tiles 7 to 8mm thick (square / rectangular ) area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15 mm thick screed bed in CM 1:4 & 25 mm thick PCC 1:2:4 type B-0 (using 12.50 mm graded aggregate) bed below screed complete all as specified and directed.

M&L coloured, joint free, Non-skid ceramic tiles 7 to 8mm thick (square / rectangular ) area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10 mm thick backing coat in CM 1:3 complete all as specified and directed.

M&L coloured, Non-skid ceramic tiles 7 to 8mm thick (square / rectangular ) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L coloured Glazed ceramic tiles in vertical surface 450mm X 300mm X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 10 mm thick plaster in CM 1:3 complete all as specified and directed.

M&L 18mm thick Granite (of any type) work (table rubbed and polished) in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over & including 20 mm thick screed bed in CM 1:3 with hole for gas pipe line complete all as specified and directed.

M&L 20 mm thick Machine cut & double side polished Kota stone slab as cupboard shelves cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

M&L 18-20 mm thick Machine cut kota stone slab as in flooring over & including 20 mm thick CM 1:4 bedding layer laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L 20-25mm thick Machine cut kota stone slab as in skirting over & including 10 mm thick CM 1:3 backing coat and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Taking down Doors chowkat or frame n exc 1.5 Sqm each but with shutters (without taking off shutters from the frames) and removing out of site complete all as specified and directed.

Taking down Doors chowkat or frame exc 1.5 Sqm and n.exc 4.00 Sqm each but with shutters (without taking off shutters from the frames) and removing out of site complete all as specified and directed.

Taking down Doors shutter of any description n exc 1.0 Sqm each and removing out of site complete all as specified and directed.

S&F Factory made solid PVC door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as specified and directed.

S&F Pressed steel frames of size 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including one shop coat of primer complete all as specified and directed.

S&F Pressed steel frames of size 105 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including one shop coat of primer complete all as specified and directed.

M&L plain cement concrete 1:2:4, type B-0 using (12.5 mm graded aggregate) in door and windows frames, any size complete all as specified and directed.

M&L applying one coat of black bituminous paint on Surfaces of any description wood, steel, iron, concrete, brick, stone, etc exceeding 10 cm in width or girth complete all as specified and directed.

S&F 30 mm Thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with decorative face veneer with lipping/frame to match complete all as specified and directed.

S&F 25 MM Thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 25 mm wide 6 mm thick teak wood lipping on veneered particle board fixed with nails as in cupboard shutter and shelves complete all as specified and directed.

S&F 100 mm size Hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F Factory made 35 mm thick 2nd class hard wood glazed & skeleton door shutters,open rebated and prepared to recive gauge etc(without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and metred beads for securing glass etc, sizes of members of shutters as specified in SSR Pt-I, Sec-8 Clause 8.24 (a) etc complete all as specified and directed.

M&L preparation of new untreated wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparation of old painted surfaces of wood/ wood based materials of any description not otherwise described over 10 cm width or girth and applying one coat of Synthetic enamel paint complete all as specified and directed.

M&L preparation of new untreated Steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

Taking down steel/wooden ventilators chowkat or frames exc 1.5 Sqm but n exc 4 Sqm each but with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down steel/wooden ventilators chowkat or frames n.exc 1.5 Sqm each but with shutters (without taking off shutters from the frames) complete all as specified and directed.

S&F powder coated anodised Aluminium alloy sections sliding windows with frames Series-C (20mm) and 3 track sliding shutters duly fitted with neoprene beading, glazing clips, two shutters with tinted glass panes 4.80 mm nominal thickness one shutter with stainless steel wire cloth 0.36mm dia & average width of aperture 1.4mm, aluminium alloy handles etc complete all as specified & directed. Note:- Quoted rates shall deemed to be included all glazing/stainless steel wire cloth, rubber packing, joining, cleats, glazing clips, aluminium snap beading, locking arrangements, handle etc.

S&F aluminium anodised ventilator with fixed aluminium frame of size 65mm x 40mm x 1.98mm thick fixed in vertical position with aluminium vertical members and bottom half portion to be provided with 4mm thick pin head glass and remaining portion to be louvered (fixed type) using 4mm thick pin head glass and louvered portion covered with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm incl necessary channel frame work, including rubber gasket and aluminium beading complete all as specified and directed. Note:- Quoted rates shall deemed to be included all glazing/stainless steel wire cloth, rubber packing, joining, cleats, glazing clips, aluminium snap beading, locking arrangements, handle etc.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or stainless steel wire staples or with second class hard wood beadings complete all as specified and directed.

S&F Aluminium, anodised, barrel tower bolts of extruded section and fixed, 200 mm long complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, 250 mm length of bolt complete all as specified and directed.

S&F Aluminium handles, cast type, anodised 100mm long complete all as specified and directed.

S&F Aluminium handles, cast type, anodised 150mm long complete all as specified and directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, over all length of cover plate 140 mm, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F 100mm butt hinges, medium weight, stainless steel complete all as specified and directed.

S&F in repair Tubular towel rail, brass CP 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F in repair SS Curtain Rod Decorative pattern 25 mm dia complete all as specified and directed.

S&F SS Curtain Rod Bracket decorative type suitable for 25 mm dia curtain rod complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning for refixing or removal to store of 15 mm bore complete all as specified and directed.

Taking down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Cutting chases in stone, concrete block or slab wall for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

Supplying and laying 16 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

Supplying and laying 20 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

Supplying and laying 50 mm dia (LDPE) silent pipe of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors complete all as specified and directed.

S&F 25 mm bore Ball brass valves,high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description & in any position not otherwise specifically provided and removing debris outside MD Land complete all as specified and directed.

M&L 5 mm thick rendering in cement mortar 1:3 with WPC on walls of sunken floor including finished even and smooth without using extra cement complete all as specified and directed. Note:- WPC shall be maesured & paid seperatly as supply only.

M&L 30 mm thick PCC type B-0, 1:2:4 (12.5mm graded aggregate) on the base of sunken portion complete all as specified and directed.

M&L for cleaning vertical and horizontal surfaces of sunken slab using wire brushing followed by sanding with emery paper for loose materials/dust and applying two coats of epoxy resin component (Dr. Fixit DAMPGUARD or equivalent) solution/mix using nylon brush pouring Base part in appropriate container followed by the Hardner part and mix thoroughly to attain homogeneous smooth paste and dilute the mixed compound with water in ratio 1 part Base: 1 part Hardner: 1 part water by slow addition and mix thoroughly until a brushable consistency is obtained, first coat will be allowed to dry for 6 to 8 hrs before application of second/final coat) including curing treated surface for 24 hrs complete including applying evenly a coat of blown bitumen @ 1.5kg/sqm over entire treated surfaces including spout holes before filling lean concrete( preparing existing surface and applying apoxy reisin and hot blown bitumen is measured and paid under this item) complete and all as specified as per manufacturer instruction.

M&L filling PCC 1:5:10, type E-2 using (40 mm graded stone aggregate) as in sunken floor after applying appropriate treatment to side walls complete all as specified and directed.

M&L 75 mm thick Cement concrete 1:3:6, type C-2 using (40 mm graded aggregate) as in plinth protection complete all as specified and directed.

Forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade A complete all as specified and directed.

Surface excavation n.exc 30cm deep & averaging 15cm deep & getting out in hard/dense soil complete all as specified and directed.

M&L 100 mm thick Cement concrete 1:4:8, type D-2 using (40 mm graded aggregate) as in subbase complete all as specified and directed.

S&F Machine pressed precast Concrete interlocking paver block rubber moulded any shape and size with grey cement and pigment confirming to IS 15658-2006 of 80 mm thickness, M-40 grade complete all as specified and directed.

M&L for sand cushening under paver block complete all as specified and directed.

M&L Providing cement concrete 1:2:4, type B-1 using (20 mm graded aggregate) as in apex stones, bed plates, kerbs, slightly rounded or chamfered angles and throating complete all as specified and directed.

Taking down cement plaster any description on brick/stone or concrete surfaces etc including racking out joints, hacking for key, scrubbing down with water to receive plaster complete all as specified and directed.

M&L for 10 mm thick rendering in CM 1:6 on fair faces of brick or concrete surfaces and finising even & smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in CM 1:6 on stone masonry surfaces or surfaces other then fair face of brick work and finishing even and smooth without using extra cement complete all as specified and directed.

M&L for applying 3 mm thick wall care putty on Internal wall complete all as specified and directed.

M&L for preparation of new palstered surface of wall and applying 3 coats of white wash complete all as specified and directed.

M&L for rendering on external surfaces of walls 15 to 17 mm thick, in two layers, comprising of under layer of 10-12 mm thick rendering in CM 1:6 and final layer of 5 mm thick in CM 1:4 on the external surfaces finished even and smooth without using extra cement with WPC complete all as specified and directed. (Note:- WPC will be measered and paid saperately as supply only.)

M&L for rendering 5 mm thick in CM 1:3 on ceiling to be finished even & smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surface of ceiling and applying 3 coats of white wash complete all as specified and directed.

M&L for preparation of plastered or unplastered surfaces of walls any width or girth etc and applying two coats of exterior weather coat paint (apex Ultima) complete over a coat of suitable primer all as specified and directed.

M&L for preparation of Newly plastered surfaces and applying two coats of oil emulsion distemper on wall etc complete all as specified and directed.

M&L for complete removal of existing treatment on wall and applying three coats of white wash complete all as specified and directed.

M&L Complete romoval of existing treatment on wall and priming plastered and other surface with alkali resistant and applying two coats of exterior weather coat (Apex Ultima) paint complete all as specified and directed.

M&L for complete removal of existing treatment on wall and applying two coats of oil bond distemper over & including one coat of primer and 3 mm thick birla white putty complete all as specified and directed.

M&L for complete removal of existing treatment on ceiling and applying three coats of white wash complete all as specified and directed.

Demolition of reinforced Concrete in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas, RCC water tank including staging and similar suspended work complete all as specified and directed.

M&L Reinforced cement concrete (nominal mix) 1:2:4, type B-1 using (20 mm graded aggregate) as in chajjas complete all as specified and directed.

M&L Formwork to chullah hoods, chajjas, troughs and similar items including edges on flat surface rough finished surface of concrete complete all as specified and directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc and hoisting if required reconnecting and re-fixing in position after Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc capacity of tank between 250 Ltr to 500 Ltr complete all as specified and directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position after Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc capacity of tank exc 500 Ltr and n exc 1000 Ltr complete all as specified and directed.

S&F in repair Rotational moulded polyethylene water storage tank of capacity 1000 ltrs (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S&F in repair Rotational moulded polyethylene water storage tank of capacity 500 ltrs (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S&F in repair Vitreous china wash basin, white, flat back, of size 550mm x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed. Note:- (i) The quoted rate shall also deemed to include "Fixing only" the Pillar tap or Basin Mixer. (ii) Pillar tap or basin mixer shall be measured & paid seperately as "supply only".

Taking down PVC (SWR)/AC pipe 100 mm dia complete all as specified and directed.

Taking down PVC (SWR)/AC pipe 75 mm dia complete all as specified and directed.

S&F PVC(SWR) pipe 110 mm dia, conforming to IS-13592-2013 type 'B', single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F PVC(SWR) pipe 75 mm dia, conforming to IS-13592-2013 type 'B', single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 110mm bore PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed.

S&F in repair PVC(SWR) bend any radius, 110 mm dia complete all as specified and directed.

S&F in repair PVC(SWR) bend any radius, 75 mm dia complete all as specified and directed.

S&F in repair 75mm dia of outlet, PVC (SWR) floor trap, plain with grating including jointing with solvent complete all as specified and directed.

S&F in repair Vitreous china wash basin, white, flat back, of size 550mm x400mm with pedestal excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed. Note:- (i) The quoted rate shall also deemed to include "Fixing only" the Pillar tap or Basin Mixer. (ii) Pillar tap or basin mixer shall be measured & paid seperately as "supply only".

Supply only pillar taps 15 mm dia, cast copper alloy, with capstain head, chromium plated, screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

Supply only central hole basin mixer cast copper alloy chromium plated complete all as specified and directed. Make:- Prayag Cat No 8550 or technocommercial equivelent make as per Appx 'C'.

S&F Toilet roll holder CP fixed to wall with chromium plated brass screws complete all as specified and directed. Make:- Prayag, Cat No BA-48 or technocommercial equivelent make as per Appx 'C'.

S&F CP corner glass shelf 300 mm long with ABS bracket, CP brass screws etc. including minimum 6 mm thick plain glass complete all as specified and directed. Make:- Prayag Cat No BEA-46 or technocommercial equivelent make as per Appx 'C'.

S&F 6" overhead shower alongwith shower arm casted fixed to 15 mm bore pipe or union complete all as specified and directed. Make:- Prayag Cat no BOS-90S or technocommercial equivelent make as per Appx 'C'.

S&F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F 32 mm bore Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap complete all as specified and directed.

S&F CP wall mixer 3 in 1 system including 1.50 m long tele shower and conncetion for overhead shower with divertor handle complete all as specified and directed. Make:- Jaquar, Cat No QQT WHM 7281 or technocommercial equivelent make as per Appx "C".

S&F three way wall mixture CP for mixing hot & cold water screwed down for iron pipe complete all as specified and directed. Make:- PRAYAG Cat No 7270 or technocommercial equivelent make as per Appx 'C'.

S&F 15 mm bore CP brass bib cock screwed for iron pipe or ferrule and fixed complete all as specified and directed. Make:- Jaquar, Cat No QQT- 7037 or technocommercial equivelent make as per Appx "C".

S&F in repair 15 mm bore CP fancy type bib taps with crutch or, screwed down, fixed complete all as specified and directed.

S& F Soap Dish complete all as specified and directed. Make :- Cantabil series Cat No BA 25 of make Prayag or technocommercial equivelent make as per Appx "C".

S&F PTMT bathroom mirror cabinate 500mm x 400mm complete all as specified and directed. Make :-Prayag cat part no -556 or technocommercial equivelent make as per Appx "C".

S&F in repair 15 mm bore CP brass angular stop cock, screwed for iron pipe and fixed complete all as specified and directed. Make:- Jaquar, Cat No QQT- 7053 or technocommercial equivelent make as per Appx "C".

S&F in repair 15 mm bore CP angle cock, chromium plated, screwed down high pressure, with crutch handle screwed both ends complete all as specified and directed.

S&F Soap dish vitreous china, white, approximate size 160 mm x 160 mm x 90 mm fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F Vitreous china squatting pan, 'Orrisa' pattern, size 580mm x 440mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe) complete all as specified and directed. NOTE FOR ITEM NO 111.00 & 112.00:- (i) Quoted rate shall also deemed to include "Fixing Only" the flushing cistern. (ii) Flushing cistern shall be measured & paid seperately as "Supply Only".

Supply only PVC valveless syphonic action type flushing cistern low level white with inlet ball valve float and handle of capacity 10 litres including brackets complete all as specified and directed.

S&F PVC connections 15 mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F in repair brass Chromium plated shower rose with or without swivel joints, 125mm size, including fixing to steel pipe or union complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick for kitchen or laboratory with plugs, washers and wastes pipe including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 36" x 18" bowl size 16" x 14" x 8" complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick for kitchen or laboratory with plugs, washers and wastes pipe including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 41" x 20" bowl size 20" x 16" x 8" complete all as specified and directed.

S&F in repair Stainless steel Kitchen plate racks 0.63 mm thick over all size 31" x 30" x10" complete all as specified and directed.

S&F in repair Stainless steel Kitchen plate racks 0.63 mm thick over all size 24" x 30" x10" complete all as specified and directed.

Taking down existing plate racks safely and keeping aside safely in store for refixing the same in position after completion of repair to tiling /plaster etc complete all as specified and directed.

M&L Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia complete all as specified and directed.

M&L Mild steel TMT bars 6 to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia complete all as specified and directed.

S&F Welded steel wire fabric of weight exc 3.5 kg/Sqm and not exc 4 kg/ Sqm, fixed to steel members with spikes complete all as specified and directed.

Removal of all loose/unsound/bad/damaged concrete or plaster existing RCC structure of slab/beams/walls by using chesel/hammar .Cut and remove unsound reinforcement bars, wires etc without damaging the sound reinforcement . clean loose rust from bars manually with brush, fixing mild steel welded fabric of weight exceeding 3.5 kg/sqm but n exc 4kg /Sqm with existing bars or by welding on it (supplymentary bars wiil be measured and paid separately). Applying eppoxy bonding agent and making good with polymer modified plaster as required thickness over a coat of rust removing alkaline primer and match the finishing to the existing surface in ground floor as following given below :- Modified plaster 15 mm to 20 mm thick in CM 1:4 with epoxy bonding agent complete all as per manufacturer instructions.

M&L for guniting shortcrete using shrinkage controlled, polymer modified fiber reinforcement cementitious mortar (Fosroc rendroc SD-40 or technocommercial equivelent make as per Appx 'C') using guniting / shotcrete pumps and allied equipment as required including taking out all loose materials from repairable surface cleaning and exposing reinforcement etc wherever required and applying a coat of epoxy bonding agent to existing concrete surface and rust proof primer to reinforcement before shotcrete / guniting complete all as specified and directed.

M&L PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in padding to obtained desired slope and fill the depression and PCC coving etc complete all as specified and directed.

M&L for water proofing treatment to non assessible RCC roofs by providing 10mm thick screed in CM 1:3 mixed with & including water proofing compound @3% by weight of cement & applying one coat of bitumenous primer @ 0.30 kg/Sqm and laying APP based polymeric modifed membrane with polyster non woven reinforced of weight not less than 3kg/Sqm of 3 mm thick with polythene finished sealing with side overlaps of 75mm & 100 mm laps at the ends of membrane by torch application method & applying two coats of aluminium paint complete all as specified and directed.

Supply only integral water proofing compound (WPC) complete all as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L Precast cement concrete block masonry type C-1 1:3:6 using 20 mm graded stone aggregate with solid block exc 10 CM in width and setting in CM 1:6 complete all as specified and directed.

Excavation in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exc 10 sq. m on plan and not exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soil complete all as specified and directed.

M&L for removing excavated material (soils) to a distance exc. 250 m but n exc. 500 m and depositing where directed complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar (Internal dia of pipe in upto 200 mm dia) complete all as specified and directed.

M&L for reinforced concrete pipes, class NP-2, 150 mm bore, laid and jointed complete with collars in trenches and jointed complete all as specified and directed.

M&L for cement concrete bed to drain pipes of 150 mm bore, including packing under, and haunching against the sides of pipes after they are laid and tested with cement concrete 1:4:8, type D-2 using 40 mm graded aggregate complete all as specified and directed.

M&L for providing precast cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregates) in precast manhole covers complete all as specified and directed.

S&F in repair 15 mm bore sink cock with crutch or , screwed down, with swing spout with flange complete all as specified and directed. Make:- Prayag Cat No 8916 or technocommercial equvelent make as per Appx "C".

M&L Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC Sheet on back face with particle board core complete all as specified and directed.

S&F MS framed work such as framed guard bars ,barred iron doors , ladders , framed balusters , walk ways , railings,frame work of water tanks, wicket gate and similar work conforming Fe 290 , Gde -E -165, for ornamental and intricate design complete all as specified and directed.

M&L Dubbing out average 12-15mm thick on irregular face of walls (whenever specifically ordered in writing by Engineer-in-Charge) in CM 1:4 complete all as specified and directed. Note:- The Surface of the dubbing out coat shall be left rough or scored to provide key for the top plaster coat.

M&L Cutting holes into or through stone masonary built in cement mortar/ cement lime mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required superficial area not exc 150 Sqcm each complete all as specified and directed.

M&L Cutting holes into or through brick wall built in cement mortar/ cement lime mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required superficial area not exc 150 Sqcm each complete all as specified and directed.

S&F 75 mm size butt hinges, medium weight, stainless steel fixed in MS frame or welded with MS angle frame complete all as specified and directed.

M&L for providing cement concrete type B-1 1:2:4 using 20 mm stone aggregate in roof kerbs or mud stops, rounded or chamfered on edges, parapets and railings upto 60 cm in height, copings, kneelers, apex stones,water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

S&F Cast iron work grade FG 150, unmachined, in railing, frames, manhole, balusters and similar articles n exc 5 kg each complete all as specified and directed.

M&L rolled mild steel Framed work Fe 410W (Gde- E- 250) quality-A as in doors or gates/wicket gate of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

Dismantling of structural steel work including doors gate etc complete all as specified and directed.

S&F Chain link MS galvanisd fencing, any size or type including line wires, any mesh , size and type to any type of standards, rails, straining bolts etc including provision of binding wire complete all as specified & directed.

Demolition of reinforced cement Concrete of any description and in any position not otherwise specifically provided complete all as specified and directed.

M&L Reinforced cement concreteType B1 1:2:4 (20mm graded aggregate) as in foundation including rafts, footings, foundation beams, plinth beams, bases for columns etc basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L Reinforced cement concrete Type B1 1:2:4 (20mm graded aggregate) as in Column, pillars, piers posts and struts complete all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or batter for fair finished surfaces of flat area complete all as specified and directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchion for fair fair finished surfaces of square, rectangular, or polygonal area complete all as specified and directed.

M&L for rolled MS plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe-410-W (Gde-E-250) quality -A complete all as specified and directed.

M&L in repair Rolled mild steel sections Fe 410 -W (Gde- E- 250) quality- A as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed.

S&F Aluminium, anodised, barrel tower bolts of extruded section and fixed 150 mm length of bolt complete all as specified and directed.

S&F Aluminium, anodised, barrel tower bolts of extruded section and fixed 100 mm length of bolt for cup board complete all as specified and directed.

M&L 1 mm thick Steel rolling shutters, without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type with two coat of synthetic enamel paint complete all as specified and directed all as per clause 10.23 of SSR Part-I.

S&F safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.

S&F Ball bearing for rolling shutters complete all as specified and directed.

S&F 75 mm long Aluminium handles, cast type, anodized for Cabinet complete all as specified and directed.

S&F 20 mm dia Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out in soft/loose soil returning filling in and ramming earth or broken rubble mixed with earth around in layers n exc 25 cm, watering & removing surplus soil to a distance n exc 50m and making good surface complete all as specified and directed.

M&L Cement concrete in foundation filling and mass concrete 1:2:4 Type B-2 (40mm graded aggregate) complete all as specified and directed.

M&L Cement concrete in foundation filling and mass concrete 1:4:8 Type D-2 (40mm graded aggregate) complete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1998 St. complete all as specified and directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long diameter of neck 5 to 10 mm complete all as specified and directed.

S&F prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Taking down carefully aluminum /copper point wiring (light, fan, switch & power) complete including fittings such as switches, ceiling rose, pendent, by unscrewing from board ,out let box, fitting and fixture such as bulk head fitting, sketch fittings and making good the disturbed rurfaces of walls floors etc all as directed.

M&L for point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits),with multi stranded copper conductor 1.5 sq mm nominal cross sectional area, single core, pvc insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No in and including medium grade, PVC Concealed conduit of dia not less than 20mm and conduit accessories concealed in wall, ISI marked with valid CML No (IS-9537-1983 for conduits and IS: 3419:1976 for conduit accessories), with mild steel/pressed steel sunken boxes (with earth dolly) duly painted with two coats of anticorrosive paint over a coat of red oxide primer internally and two coats of black bituminous paint over a coat of red oxide primer externally, covered with 3mm thick Hylam sheet cover for fixing of switches, sockets etc including PVC insulated multi stranded copper conductor 1.5 sqmm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dully complete all as specified and directed at site for the following :

One light/ Fan point controlled by one way switch

One Bell point controlled by one switch bell push

One 3 pin socket outlet 5 amps on the same board with other switches.

One 3 pin socket outlet 5 amps on independent board.

Ditto all as per item No 172.00 here in before but 2.5 Sqmm stranded copper conductor and independent board for 15 Amps switch/ socket point complete all as specified and directed.

S&F switch piano flush type single pole one way 5 Amps 230 Volts complete all as specified and directed.

S&F switch socket out let 3 pin 5 Amps flush type 230 Volts multipurpose complete all as specified and directed.

S&F switch socket out let flush type 230 Volts 5 Amps and 15 Amps multipurpose 3 Pin, 15 Amps and one pin, 5 Amps controlled by one switch complete all as specified and directed.

S&F socket out let 3 pin, 5 Amps, 230 Volt multipurpose flush piano type complete all as specified and directed.

S&F in repair fan regulator Electronic Step type (min 5 steps) 2 module, 120W complete all as specified and directed.

S & F switch Bell Push botton type 5 Amps single pole one way complete all as specified and directed.

M&L for point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits),with multi stranded copper conductor 1.5 sq mm nominal cross sectional area, single core, pvc insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No in and including medium grade, PVC Concealed conduit of dia not less than 20mm and conduit accessories concealed in wall (Brick/stone masonary), ISI marked with valid CML No (IS-9537-1983 for conduits and IS: 3419:1976 for conduit accessories), with modular metal flush boxes & cover plate with frame of white colour of suitable size as required at site; including PVC insulated multi stranded copper conductor 1.5 sqmm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth duly complete including replastering and making good the surface of wall and painting with existing colour all as specified and directed at site for the following :

One light/ Fan point controlled by one way switch.

One Bell point controlled by one switch bell push

One 5 Amps socket on same board with other switches.

One 5 Amps switch socket combination on independent board.

Ditto all as per item No 180.00 here in before but 2.5 Sqmm stranded copper conductor and independent board for 15 Amps switch/ socket point complete all as specified and directed

S&F modular switch piano flush type single pole one way 6 Amps,1 module complete all as specified and directed

S&F moduler socket 6 Amps -2/3 pin combined 2 module complete all as specified and directed

S&F modular switch piano flush type single pole one way 16 Amps,1 module complete all as specified and directed

S&F Modular socket combination 6/ 16 Amps 2/3 Pin combined 2 module complete all as specified and directed.

S & F Modular switch Bell Push 6 Amps single pole one way 1 module complete all as specified and directed

S&F in repair Bell Ding Dong AC 230 volts type single pole complete all as specified and directed

S&F modular fan regulator Step type 120W 2module complete all as specified and directed.

S&F ceiling rose surface backelet ISI marked 2 to 3 terminal isolated body complete all as specified and directed

S&F lamp holder PVC/Polycarbonate type ; insulated body with back plate for battern fittings complete all as specified and directed

S&F LED batten fittings 4ft, 20 Watt (Min 1900 lumens) with tube rod, clamps including PVC gutties and flexible wire and connecting to ceiling rose complete all as specified and directed.

S&F LED Batten fittings 1ft, 5 Watt (min 380 lumens) with tube rod, clamps including PVC gutties and flexible wire and connecting to ceiling rose complete all as specified and directed.

S&F LED Retrofit lamp 9 Watt white 6500K cool day light Minimum lumens 600 complete all as specified and directed

S&F DB sheet metal enclosure 4 way TPN 415 volts double door for mounting MCBs complete all as specified and directed

S&F DB sheet metal enclosure 8 way SPN 240 volts for mounting MCB double door complete all as specified and directed

S&F MCB DP 32 Amps 240 volts, rupturing capacity 10 KA complete all as specified and directed

S&F MCB TPN 63 Amps 415 Volts, rupturing capacity 10KA complete all as specified and directed

S&F MCB single pole 5 to 32 Amps C series, rupturing capacity 10 KA complete all as specified and directed

Taking qown carefully submain wiring of any size, any run etc complete all as specified and directed

M&L for sub main wiring with two runs of 2.5 Sqmm single core PVC unsheathed and insulated 1100 Volt grade/Multi stranded copper conductor drawn through & including PVC conduit and accessories fixed concealed on walls, ceiling floors etc including one run of PVC insulated and unsheathed cable of copper conductor of 2.5 Sqmm single core as earth continuity wire all as specified and directed.

M&L for sub main wiring with two runs of 4.00 Sqmm single core PVC unsheathed and insulated 1100 Volt grade/Multi stranded copper conductor drawn through & including PVC conduit and accessories fixed concealed on walls, ceiling floors etc including one run of PVC insulated and unsheathed cable of copper conductor of 4.00 Sqmm single core as earth continuity wire all as specified and directed.

M&L for sub main wiring with two runs of 6.00 Sqmm single core FRLS PVC unsheathed and insulated 1100 Volt grade/Multi stranded copper conductor drawn through & including PVC conduit and accessories fixed concealed on walls, ceiling floors etc including one run of PVC insulated and unsheathed cable of copper conductor of 6.00 Sqmm single core as earth continuity wire all as specified and directed.

Note for Item No 200.00 to 202.00 :- The above mentioned specified runs of single core main cables and specified runs of earth continuity conductors and the relevant conduit with accessories shall be measured as one runs length. The small extra lengths required for loops etc for connection in DBs shall deemed to be included in quoted rate and only the cable covered in conduit shall be measured.

S&F Metal body exhaust fan 225 mm sweep AC, 240 volts consist of Double ball bearing & Louvers metal body, fixed as per manufacturer instruction, connecting with and including 1.5 Sqmm copper conductor, PVC insulated and PVC sheathed three core cable including making sutable size circular hole in brick / PCC block / stone masonary wall built in cement mortar and making good finishing and painting as existing colour to disturbed surface complete all as specified & directed.

Taking down & Refixing Exhaust fan 225mm sweep AC, 240 volts,Metal body ,in same location after cleaning, greasing and painting with synthetic enamel paint by spreying including filling cavities with filler, one coat after cleaning all dusts etc and connecting up including provision of flexible wire from ceiling rose/connector to fan complete all as specified & directed.

Taking down & Refixing Ceiling fan 1200mm sweep AC, 240 volts,Metal body, after cleaning , greasing and painting with synthetic enamel paint by spreying including filling cavities with filler, one coat after cleaning all dusts etc and connecting up including provision of flexible wire from ceiling rose/connector to fan complete all as specified & directed.

Taking down & refixing of water heater geyser 25 Ltr capacity Glass lined metal body Bajaj New shakti Geyser, vertical type with complete accessories in same location after completion of repair of bldg complete all as specified & directed.

Supply & Installation of Electric water heater geyser storage type 25 Ltr capacity BEE 5star rated as specified and directed by Engr in Charge.

M&L for earthing complete with galvanized steel earth plate electrode of 60 cm x 60 cm x 6mm thick buried directly in ground [earth pit not less than 2.25 metre deep below normal ground level] with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized earth wire of 4mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 of MES SSR Part I all as specified and testing on completion including provision of earth lead protected by 15 mm dia light grade GI pipe & watering pipe shall be 20 mm bore medium grade GI pipe including all excavation and earth work in any type of soil, PCC pit with RCC cover, char coal, salt, funnel etc complete.

NOTE FOR ITEM NO. 208.00:- Rate quoted by tenderers shall be deemed to include for following provisions:- [i] Excavation & earth work in any type of soil including removing of surplus material upto 50 Mtr. [ii] PCC 1:3:6 type C-1 using 20mm graded aggregate in pit & 40mm thick precast RCC 1:2:4 type B1 cover 50x50 cm with 8mm TMT bars @ 10 cm C/C both ways with handles. [iii] Main earthing lead from earth electrode to test point upto 7.5 mtr. [iv] Funnel with watering pipe [GI pipe] 20mm bore [ISI marked] medium grade & copper lugs, charcoal & salt as reqd. [v] GI protection pipe of size 15 mm bore light grade 7.5 mtr.

Supply, fixing, testing and commissioning 30W LED security light fitting with system output of 3000 lumens & with dedicated street light optics, System efficacy of greater than 100lm/W luminarie should have pressure die cast aluminium LM6 housing. Luminaire should have dedicated street light optics for better uniformity & spacing. Luminarie should have air vents in housing for proper thermal management. Min IP preventation should be IP65. System power consumption (including driver losser) should not exceed 20W complete all as specified & directed.

S&F security light bracket made out of GI pipe 25mm light grade ISI marked 1.2 Mtr long bend to shape as required for LED fittings at site including M S Clamp 2 Nos made out of flat iron 25x3 mm with necessary nuts Bolts and two coats of alluminium paint over a coat of red oxide primer complete all as specified & directed.

Taking down existing energy meter from site and deposit to MES storeyard and refixing the same meter after completion of building repair work complete all as specified & directed.

S&F Sheet metal enclosures with socket plug top and single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20Amp MCB SP 'C' series of 240 volts of rupturing capacity 10 KA complete all as specified & directed.

M&L for removing excavated material not exc 50 m and depositing where directed at a level not exc 1.5 meter above the starting point complete all as specified and directed.

Taking up/down GI tubing and connections 25 mm size of pipes including all fittings complete all as specified and directed.

Taking up/down GI tubing and connections 20 mm size of pipes including all fittings complete all as specified and directed.

S&F GI tubing medium grade 25 mm dia with all fittings laid in trenches complete all as specified and directed.

S&F GI tubing medium grade 20 mm dia with all fittings laid in trenches complete all as specified and directed.

Supply ,install,testing and commisioning transformer of capacity 500 KVA, 11/0.433 KV, 3 phase, 50 Hz, copper wound out door type distrubution transformer with off circuit tap changer having +7.5% tapping in steps of 2.5% tapping confirming to IS 1180-2014, complete with all fittings and accessories EEL-3 all as specified and directed comprising following accessories:-

Off circuit changing switch with indicating plate and oil conserverter with filling hole and cap -01 no Silica gel breather with initial charging -01 set Drain /sampling/filter valve with plug -01 no Top filter valve with plug -01 no Explosion vent with diaphram -01 no Thermometer pocket -2 nos Rating and diaphragm plate -1 no Earthing terminal -2 no Additional neutral bushing for solid earthing -1 no Plain oil level guage -1 no Lifting plug -2 nos Air release plug -2 nos Bi directional & uni directional plate roll -4 nos HV bushing outdoor (03) Nos & LV end box with bushing complete set. Temp gauge dial type Provn of neutral earthing

M&L for sand cushioning with fine dry unwashed sand in trenches for protection of cables complete all as specified and directed. Note:- Only punned thickness shall be measured.

Supplying and laying un-reinforced precast concrete cable cover class HV, type - I, flat, size 300mm x 180mm x 40mm ISI marked complete all as specified and directed.

Supply & Laying un-reinforced precast concrete cable cover class LV low voltage type -I flat size 250mm x 150mm x 40mm ISI marked complete all as specified and directed.

Supply laying and testing cable XLPE insulated, screened PVC bedded, galvanized steel strip or wire armoured electric power cables (heavy duty) with aluminium conductor conforming to IS:7098 (Part 11) 11 KV (E) earthed grade cross sectional area 95 sq mm 3 core complete all as specified and directed.

S&F prestressed concrete pole 11.0 metres long, 152mm x 152mm at top and 152mm x 260mm at bottom, class 9 complete all as specified and directed. Note:- Excavation, earth work & PCC for foundation will be measured and paid seperately.

Supply and install HT 11 KV outdoor type gang operated air break switch triple pole, mechanical operated with operating mechanism worked from ground level suitable for horizontal or vertical mounting fixed type complete with 9 insulators & steel frame work for current rating upto 200 Amps complete all as specified and directed.

S&F drop out fuse assembly 11 KV with 6 Nos Post insulators and channels, operating rod/pipe etc triple pole complete all as specified and directed.

M&L for lightning arrestor non linear resistor type or expulsion type confirming to IS-3070 Part I complete line discharge or transmission class - 2 nominal discharge current 10 KA & high discharge 100 KA assembly suitable for 11 KV including all clamps, nuts, bolts & washers complete all as specified and directed.

M&L Cable end joints and testing cable end box HT 11 KV (cold shrinkable) with jointing material suitable for HT XLPE cable of size 3 core 95 sqmm outdoor type complete all as specified and directed.

M&L for Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized iron earth strip 32mm x 6mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of protection pipe galvanized iron 40 mm dia light grade pipe and watering pipe shall be 20 mm bore medium grade including all excavation and earth work in any type of strata, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete as detailed below and all as directed.

NOTE FOR ITEM NO 228.00:- Rate quoted by tenderers shall be deemed to include for following provisions:- (i) The concrete pit shall be PCC 1:3:6 type C-1, 40 mm thick pre cast cover slab of RCC M25 design mix using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I. (ii) Item includes the cost of 7.5 M GI pipe for protection of earth wire. Any variation in length shall be adjusted through deviation order. (iii) Item includes cost of 7.5 M earth GI earth strip 32 x 6mm. Any variation in length shall be adjusted through deviation order.

S&F prestressed concrete pole 9.0 metres long, 102mm x 172mm at top and 102mm x 279mm at bottom, class 10 complete all as specified and directed. Note:- Excavation, earth work & PCC for foundation will be measured and paid seperately.

Taking down old ACSR conductor from LT line complete all as specified and directed.

M&L for aluminium conductor, steel reinforced (ACSR) of any size, stringing properly on insulators on pole and binding with aluminium tape / binding with conductors, jumpers etc complete all as specified and directed.

M&L for stringing and fixing only of aluminium conductor steel re-inforced (ACSR) on LT poles including binding wire complete all as specified and directed at site of any type ACSR conductor complete all as specified and directed.

M&L for cross arms, bracings, supports, clamps, straps D-clamps, back plates and MS frames fabricated from structural steel sections such as MS channel, angle iron and flats etc including nuts, bolts, washers, eye hooks, welding, bending cold or hot drilling holes for bolts in any shape or size including two coats of aluminium paint over a coat of red oxide primer after preparation of steel surface complete all as specified and directed.

S&F of stay wire galvanised strand (grade-2) size 7/3.15mm complete all as specified and directed.

S&F of stay assembly complete with 16mm dia stay rod with accessories shown in electric plate No. 1 of SSR Part-I complete all as specified and directed. Note:- Loop insulator, Stay clamp, excavation and concrete measured and paid separately.

S&F of loop type insulator vitreous porcelain white/ brown or green small size with overall dimension 65x90mm, clearence of hole 16mm for fixing on stay wire complete all as specified and directed.

M&L of shackle type Insulator porcelain vitreous white/ brown or green, 75 mm high and 90mm dia suitable for working pressure of 1100 Volt including Galvanized steel straps of size 31x3 mm, nut, bolt of dia 12 mm and washers of suitable size complete all as specified and directed.

Taking down old XLPE cable of any size from site complete all as specified and directed.

Supply & Laying in trenches / poles / walls XLPE insulated, armoured, heavy duty electric power cable with aluminium conductor 1100 volts grade for following size with lugs complete all as specified and directed. Note:- Excavation and earth work, GI pipe protection, sand cushioning shall be measured and paid under relevant items.

16 Sqmm x 4.0 core

25 Sqmm x 3.5 Core

120 Sqmmx 3.5 Core

185 Sqmmx 3.5 Core

240 Sqmmx 3.5 Core

Supply, Installed, Testing and Commissioning of LT Panel floor mounted CPRI approved out door type 3 phase 4 wire system 50 Hz AC supply, factory made fabricated with 3.15 mm thick and inner sheet 2.0mm thick complete CRCA sheet duly powder coated IP-54 complete with compartmentalised,with angle iron frame (size of angle iron 40mm x 40mm x 6mm) front/back door operated with hinges, dust and vermin proof with neoprene gaskets including internal wiring by suitable size of copper wire, danger board, cable glands, lugs complete with suitable for fixing the following accessories:-

M&L for brick work with Sub class "B" bricks, straight or curved on plan exc 6 m mean radius built in CM (1:6) complete all as specified and directed.

M&L for 15 mm thick rendering in CM 1:4 over brick masonry surfaces or surfaces other then fair face of brick work and finishing even and smooth without using extra cement complete all as specified and directed.

M&L Cement concrete in foundation filling and mass concrete 1:3:6 Type C-2 (40mm graded aggregate) complete all as specified and directed.

M&L Cement concrete in foundation filling and mass concrete 1:2:4 Type B-1 (20mm graded aggregate) complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L Mild steel work for Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for taking down unserviceable pin insulator of any size complete all as specified and directed.

M&L for pin type, porcelain, vitreous, white, brown or green insulator including one galvanized mild steel spindle, two galvanized iron washers and one galvanized iron nut, 100 mm height, 65 mm dia for 1100 volt grade complete all as specified and directed.

S t modi

JAMNAGAR ELECTRIC AND MACHINERY CO