interpretation center shatadhar

Amount

C/o main building portion-Excavation in foundations, trenches etc, in earth work, lift upto 1.50 Meters stacking the excavated soil not more than 3 meters claear from the edge of the excavation and then returning the stacked soil in 15cm. layers, whenrequired in to plinth sides of foundations etc. consolidating each deposited layer byramming and watering and then disposing of all surplus excavated earth as directed with in a lead of 20 meters(PJ works 50% each)

Providing and laying cement concrete 1:6:12 and curing complete excluding the coat of form work in:

Providing form work with steel plates 3.15mm, thick welded with angle iron in frame 30x30x5mm . so as to give a fair finish including centering, shuttering ,structting and propping etc. with wooden batten and ballies, height of propping and centering below supporting floor to ceiling not exceeding 4 mtrs. and removal of the same for insitu-reinforcement concrete & plain concrete work in : foundation, footing, basis of Columns, Mass Concrete etc.

Circular Columns

Beams

Flat Surface such as soffits of suspended floor, roofs, landing etc.

Stair

Edge of Slabs and Breaks in Floor and Walls

Concrete work-Providing and laying Cement concrete work 1:2:4(1 Cement :2 Sand:4 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement concrete work in: Foundation, footing bases of columns and the like and mass concrete.

Suspended Floor roofs, landing and shelves and their support balconies, beams, girders, bressumers and cantilever upto upto floor two level.

Stair Case(Except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto floor two level.

P/L Cement Concrete 1:11/2 : 3(1: Cement:11/2 Sand:3Graded Stone Aggregate 20mm nominal size) including curring complete excluding cost of Form Work-Columns, pillars posts and struts upto floor two level

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level.

Brick Work-Using 2nd class common brunt brick in cement mortor 1:5 ( 1Cement:5 sand)

Half brick masonary in common burnt clay building bricks in:- Cement Mortar 1:4(1: Cement 4: Sand) Second class Bricks

Stone Work-Random rubble Masnory /polygonal rubble masnory in walls with hard stones of approved qly. In foundation & plinth including levelling up with cement concrete 1:6:12( 1 cement:6 Sand :12 Graded stone aggregate 20mm Nominal size) at plinth level in Cement Mortor 1:6 ( 1cement : 6 Sand)

NDCR Masnory /polygonalrubble masnory in walls with hard stones of approved qly. In Superstructure above plinth level and up to floor level two including levelling up with cement concrete 1:6:12( 1cement:6 Sand :12 Graded stone aggregate 20mm Nominal size) at plinth level in Cement Mortor 1:6 ( 1cement : 6 Sand)

Wood work-Providing Wood work in frames of doors , Windows , Clerestory , windows & other frames wourght framed & fixed in position .2nd class Deodar wood

Providing Wood work in Trusses ,purlins ,rafters,posts,post plates ,wall plates and the like wrought framed hoisted and fixed in position 2nd class Deodar wood

Providing wood work in frames of false ceilling partition etc sawn and put up in position 2nd class Deodar wood

Providing eves Board 200mmx25mm thick including fixing in position 2nd class deodar wood

Providing and fixing wooden plank ceilling with planks over lapping each other and jointed with wood screw ( frame work to be paid for separately) 20mm thick 1st class deodar wood

Providing and fixing panelled glazed or panelled and glazed shutters for doors windows and clerestory windows, including black enamelled iron butt hinges with necessary screw. 1st Class Deodar wood 40mm thick

WIRE GAUGE SHUTTER: Providing and fixing wire gauge shuttering using galvanised M.S wire gauge of I.S gauge desiugned as G.with eire of dai 0.56 mm for doors windows and clerestorey windows including bright finsihed balck enamelled iron hinges with necessary screws. 40 mm Th. 1st Class Deodar Wood 35mm th.

Providing and fixing M.S. grills of required pattern in wooden frames of windows etc. with M.S. Flats, Square or round bars wirth round headed bolts and nuts or by screw. Plain grill

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete.300x16 mm

Providing and fixing aluminium tower bolts(berrel type) anodized trans parent or dyed to required shade and colour with screws etc.complete) -150x10mm

Providing and fixing aluminium handles anodized transparent or dyed to required colour of shade with necessary screws etc. complete.-125mm

Providing and fixing bright finshed hard drawn hook and eyes 150mm

Providing 40x3mm flat iron hold fast 40cm. Long including fixing to frame with 10mm diameter bolts nusts and wooden plugs and embeding in cement concerete block. 30X10X15cm 1:3:6(1 Cement, 3 Sand,6:Graded Stone aggregate 20mm nominal size)

Flooring-White glazed tile 6 mm thick in flooring ,treads of steps and landing laid on bed of 12 mm thick cement mortor 1:3 ( 1cement : 3 Sand ) finished with flush pointing in white cement.

White glazed tile 6 mm thick in skirting ,Riser of steps and Dado laid on bed of 12 mm thick cement mortor 1:3 ( 1cement : 3 Sand ) and joint with cement Slurry.

Kota Stone slab 25mm thick in risers of steps, skirting dado and pillars laid on 12mm(average) thick cement mortor 1:3(1:Cement:3 Sand) and jointed with gray cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete.

Kota Stone slab 20 mm thick in floor in ratio 1:4 jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

Slate roofing with 7.5 cm lap double layer fixed on wooden battens ( wood work to be paid for separately)

Providing & Fixing Ridges or Hips 60 cm over all with 0.60 thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns primer coating i/c fixing with prepainted iron J or L hooks volts and nuts 6mm dia and prepainted GI Limpet and bitumen washers complete with all accessoies as required as per the direction of Engineer in charges.

Providing & Fixing Valley or Hips 60 cm over all with 0.60 thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of back coat of polyster of 5 microns primer coating i/c fixing with prepainted iron J or L hooks volts and nuts 6mm dia and prepainted GI Limpet and bitumen washers complete with all accessoies as required as per the direction of Engineer in charges.

Priming, Painting and Distempering work-Applying priming coat over new steel and steel based surfaces after and including preparing the surface by throughly cleaning oil, grease, dirt and other foreign sand preparing and knotting.

Painting two coats (excluding priming coat on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt , dust and other foreign matters. With Enamel paint other than white

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by throughly cleaning oil, grease, dirt and other foreign sand preparing and knotting.

Painting two coats(excluding priming coat) on new wood and wood based surfaces, with readymixed paint, brushing to give an even shade including cleaning of all dirt, dust and other foreign matter sand papering and stopping.

Polishing two coats with french Polish on new wood and new wood based surfaces to give an even surface including cleaning the surface of all dirt .dust and sand papered smooth and including a coat of wood filler.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortor drops ,dust,loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete.

Plastering , White Washing , Distempering work and other finishing work- 6 mm cement plaster to ceiling in Cement Mortor 1:3 (1:Cement, 3 Sand)

15mm Cement plaster in Single coats on fair side of brick /concrete / stone walls for interior plastering up floor level two including arrises . internal rounded angles ,chamfer & /or rounded angles not exceeding 80 mm in girth & finished even & smooth . in cement mortor 1:6

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated Ceilling / Slopy surfaces to give an even shade over and incuding a priming coat with distemper priming of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth priming coat with distemper primer.

Stone soaling under floor properly hand packed and consolidation by hand ramming complete

Providing under layer for plinth protection of 75 mm thick ( unconsolidated ) bed of dry brick/ stone aggregate 40mm nominal size )wall rammed and consolidated and grouted with fine sand including preparation of ground

Providing plinth protection 50 mm thick with cement concrete 1:3:6 ( 1cement :3 Sand :6 Graded stone aggregate 20mm nominal size.

Supplying & fixing rolling shutter of approved make made of 80mm X 1.25 mm MS laths interlocked together through their entire length and joined together at the end by end locks mounted on specially designed pipe shaft , with bracktsside guides and arrangement for inside & out side locking with push pull operation complete but excluding the cost of the top cover and spring.shutter having width below 3.5 mts

Providing & fixing 27.5 centimetre long wire spring grade No - 2 for rolling shutter

Providing & fixing top cover for shutter having width below 3.5 mts

Providing & fixing ball bearing for rolling shutters

NAVDEEPAK THAKUR