PROVN OF 06 X TOILET AND BATHROOM AT ASC BN AND PROVN OF HIGH MAST SECURITY LIGHTS NEAR CVY GROUND AWS OF FD REGT AT ALHILAL MIL STN

Amount

SCHEDULE 'A' PART-I Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches,nexc 1.50m wide and n exc 1.50m in depth for foundation n exc 10 sq m on plan and getting out any type of soil complete all as specified and directed.

M&L PCC 1:3:6 type C-2 (using 20mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in Cement mortar 1:6, complete all as specified and directed.

M&L Brick work with sub class 'B' bricks, straight or curved on plan, to any radius, in half brick thick wall, using old size brick, built in cement mortar 1:4, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc25 cm any type of soil complete all as specified and directed.

Removing excavated soil n exc.50m and depositing where directed at aleveln exc 1.50m above the starting point complete all as specified and directed.

M&L RCC M-15 (nominal mix) , type B-1 (using 20mm crushed stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, basement slabs, under-reamed piles and mass concrete etc. complete all as specified and directed.

M&L RCC M-15 (nominal mix), type B-1 (using 20mm thick crushed stone aggregate) as in slabs supported on walls beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the line complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, caltilevers, shelves including supports, overhangs etc also splays between floors and beams etc, fair finished surface complete all as specified and directed.

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No. 11 above but 6 to 8mm dia.

S&F mild steel TMT bars 5 mm dia and over up to 10 mm dia in stirrups,spacers and binders and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates Fe 410-W (Gde E-250) quality-A, complete all as specified and directed.

S&F mild steel plates, plain or chequered, 5mm thick or over in thicknessin available sizes Fe 410-W (Gde-E-250) quality-A complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified, compete all as specified and directed. (Colour as approved by GE)

M&L pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, facia and fixed with self tapping screws as specified. (Colour as approved by GE)

M&L 15mm thick plaster in CM 1:4 on brick or concrete surface/stone masonry surface, as on external surfaces, surface finished even and smooth without using extra cement complete all as specified and directed.

M&L 10mm thick plaster in CM 1:6 on brick or concrete surface, as on internal surfaces, surface finished even and smooth without using extra cement complete all as specified and directed.

M&L 150mm thick hardcore of gauge n. exc 63mm, deposited, spread and levelled in laysers, watered and rammed to a true surface complete all as specified and directed.

M&L 75mm thick PCC 1:4:8 type D-2 using 40mm crushed stone aggregate as in sub base complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4 type B-0 (12.5mm graded stone aggregate) 25mm thick as in sub base of flooring, leveling course of flooring or levelling course of roof etc, complete all as specified and directed.

M&L 50mm thick PCC M-10 type C-2 (using 20mm thick crushed stone aggregate) as in plinth protection/foot path finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L preparation of newly plastered or unplastered surface of wall and applying two coats of white wash complete all as specified and directed.

M&L preparation of newly plastered or unplastered surface of wall and applying two coats of cement base paint complete all as specified and directed.

M&L preparing new surface of steel of any description, over 10cm width or girth not other wise described and appliying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer, complete all as specified and directed.

M&L joint free coloured glazed ceramic tiles in vertical surfaces 350x250x7mm, 450 x 350x 7mm as in skirting/dado etc, over and including 10mm thick backing coat in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles complete all as specified and directed.

M&L Non-skid, coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.06 sqm but not exc 0.11 sqm as in floors etc laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with white or coloured cement to match the colour of tiles complete all as specified and directed.

S&F GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre complete all as specified and directed.

M&L 6mm thick E-board (classic) false ceiling of size 600x600mm fixed to snap grid false ceiling complete all as specified and directed.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, supplying and fixing in opening as per specifications & directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat molded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified & directed.

S&F 100 mm size aluminium butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin ,anodised, type B-21 complete all as specified and directed.

S&F 150 mm size (length of bolt) aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed

S&F aluminium handles, cast type, anodised of size 150 mm long, complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete with glazing bars dove tailed or welded, complete all as specified and directed.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc. 0.5 sq.m in each pane complete all as specified and as directed.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 110mm bore of pipe PVC (SWR) pipe single socketed in any length with rubber ring joints, fixed to wall/laid in trenches or in floors etc. complete all as specified and directed.

S&F 75mm bore of pipe PVC (SWR) pipe single socketed in any length with rubber ring joints, fixed to wall/laid in trenches or in floors etc. complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends complete all as specified and directed.

S&F 75mm bore PVC (SWR) junction, (single T) equal or unequal ,complete all as specified and directed.

S&F 100/110mm bore PVC (SWR) bends complete all as specified and directed.

S&F 100/110mm bore PVC (SWR) junction, (single T) equal or unequal ,complete all as specified and directed.

S&F 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed .

S&F PVC (SWR) vent cowl 100/100 bore dia, complete all as specified and directed.

S&F mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe290 Gde-E-165 complete all as specified and directed.

S&F 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including fixing fittings such as GI nipple for inlet, outlet, washout and overflow etc, including 25mm size ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and directed.

S&F vitreous china coloured wash down water closet pan (Padestal Pattern), including connection to flush pipe, 'P' or 'S' trap, with fixing bolts PVC seat cover with chromium plated mild steel hinges device (excluding flushing cistern and flush pipe), complete all as specified and directed.

S&F vitreous china squatting pan water closet, orissa pattern, size 580mm x 440mm white with integral foot rests (excluding flushing cistern and flush pipe) including PVC (SWR) 'S' trap,setting trap and pan in lime concrete and jointing to flush pipe (fixed in repair) and making good disturbed surfaces of floor and match with existing follor, complete all as specified and directed.

S&F in repairs 10 litres capacity PVC valve less symphonic action type flushing cistern (ISI Marked) low level with inlet ball valve, float and handle including brackets & 32 mm size PVC flush pipe, complete all as specified and directed.

S&F Vitreous china, wash hand basin, (white) of size 550mm x 400mm including brass CP waste coupling 32mm size with long screwed shank and fly nuts, PVC medium grade 32mm dia waste pipe, chain and plug, porcelain stopper , PVC connection 15mm dia, 450mm long with brass CP nuts and washers at both ends (fixed in repair), complete all as specified and directed.

S&F PVC connection 15mm size, 450 mm long with PTMT nuts complete all as specified and directed.

S&F brass chromium plated tubular towel rail, 20mm dia, D type 60cm long , fixed to wall with CP brass screw and PVC rawl plugs, complete all as specified and directed.

S&F soap dish stainless steel fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F fancy type, chromium plated, bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge.

S&F pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for 15 mm bore iron pipe complete all as specified & directed.

S&F 15mm bore fancy type stop valves/angle cock (two way if required), cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union complete all as specified and directed.

S&F in repairs 20mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for GI tubing complete all as specified and directed.

S&F swivel shower of PTMT any colour for fixing with shower arms 15mm size, 195mm long with bend of 45 degree with flange of PTMT any colour (minium eight 40gms) complete all as specified and directed.

S&F steel water tubing, 15 mm bore, galvanised , "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

S&F steel water tubing, 20 mm bore, galvanised , "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

M&L walling of random rubble, stone masonry un-coursed, brought upto course with best quality locally available harder stsones such as granite, trap, basalt stone etc well bonded, bedded and solidly hearted built in cement mortar 1:6, complete all as specified and directed.

M&L 75mm thick PCC 1:4:8 type D-2 using 40mm crushed stone aggregate as in sub base of paver block complete all as specified and directed.

M&L 50mm sand filling under floors in foundations including watering and consolidation complete all as specified and directed.

M&L 60 mm thick machine pressed precast concrete interlocking paver block with grey cement and pigment in any shape and size (shape as approved bt GE) laid in path, porch, hard standing or flooring etc conforming to IS-15658-2006, M-35 grade over and including 25 mm thick layer of sand cushioning, complete all as specified and directed .

M&L PCC M-10 (nominal mix) type C-1(using 20mm crushed stone aggregate) as in surface channels or drains etc complete all as specified and directed.

M&L extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc. complete all as specified and directed.(inner girth only measured)

Excavating over areas, n exc 1.5m deep and getting out in any type of soil complete all as specified and directed.

Excavating over areas, exc 1.5m and not exc 3.00m deep and getting out in any type of soil complete all as specified and directed.

Excavating over areas, exc 3m and not exc 4.50m deep and getting out in any type of soil complete all as specified and directed.

M&L hardcore of guage exc 63mm but no exc 100mm, deposited, spread and levelled in layers not exc 15cm thick, watered and rolled/rammed to a true surface complete all as specified and directed.

M&L brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in Cement mortar 1:4, complete all as specified and directed.

M&L 200mm thick PCC 1:3:6 type C-2 (using 40mm crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L 50mm thick PCC 1:2:4 type B-1 (using 20mm crushed stone aggregate) as in flooring finished with even and smooth using extra cement complete all as specified and directed.

M&L plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate cast in situ in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straight or curved) complete all as specified & directed.

M&L pre-cast cement concrete type B-1 1:2:4 (20mm graded crushed stone aggregate) as in landings, cover slabs for man holes,chullah hoods,chajjas,water troughs,mangers,shelves and similar articles with plain faces, set in CM 1:4 complete all as specified and directed.

M&L 20mm thick rendering in CM 1:3 on internal surfaces of wall without using extra cement including mixing of water proofing compound complete all as specified and directed. Note: WPC shall be measured and paid separately.

Supply only integral liquid water proofing compound.

M&L RCC 1:2:4 (Nominal mix) type B-1 (using 20mm thick crushed stone aggregate) as in slab supported on walls, beams and columns in floors, roofs, landing, balconies, canopies, deck slabs and in shelves and the like complete al as specified and directed. Note: Reinforcement if used shall be measured and paid separately under relevant item.

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc, vertical or to batter complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200m thick (horizontal and sloping) complete all as specified and directed.

S&F 100mm dia cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors or fixed to walls complete all as specified and directed.

S&F 100mm dia cast iron vent cowls complete all as specified and directed.

S&F 150mm internal dia bore reinforced concrete pipes, class NP3, laid and jointed complete with collars complete all as specified and directed.

Concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in complete all as specified and directed.

M&L brick work with sub class 'B' bricks in one brick thick honey comb walling, built in CM 1:4 complete all as specified and directed.

M&L broken bricks loose aggregate for loose filling, of gauge 40mm to 80mm graded in soakage pits, soakage wells complete all as specified and directed.

SCHEDULE 'A' PART-II M&L for point wiring for one light/fan/call bell point controlled by one 5/6 Amp switch with 1.5 Sqmm two single core multistranded copper conductor FRLSH, PVC insulated unsheathed heavy duty cable 1100 volts including continious earth wire of size 1.5 Sqmm copper conductor multistranded FRLSH, PVC insulated (unsheathed) drawn into concealed rigid non-metallic PVC conduit med grade ISI marked not less than 20mm wide of 1.8mm wall thickness ISI marked including modular GI sunken flosh box (modular GI flush boxes of any way i.e. 1 to 8 way as per site requirement) for mounting switches, sockets, fan regulators etc & making good to disturbed surfaces as well as matching with existing whitewash colour/surface complete all as specified and directed for the following:- (a) Wiring shall be done by using proper colour coding. (b) Earth wire shall be of green colour. (c) On RCC roof/ceiling PVC conduit shall be provided on surface with proper fixing clamps all as directed. Note: Quoted rates deems to be included the cost of modular plate (1 to 8 way) for mounting switches, sockets & regulators as required at site.

All as per the description of serial item No 88 here-in-before but one 5 pin socket outlet, 5 amps on the same board complete all as specified and directed.

All as per the description of serial item No 88 here-in-before but one 5 pin socket outlet, 5 amps, independent complete all as specified and directed.

All as per the description of serial item No 88 here-in-before but for one 16 Amps socket point on independent board with 2.5 Sqmm PVC insulated FRLS-H multi-stranded copper conductor with 2.5 Sqmm PVC insulated FRLS-H multi-stranded copper conductor as earth wire & making good to disturbed surfaces as well as matching with existing whitewash colour/surface complete all as specified and directed.

S&F modular switch 1 way 6 A,1 module complete all as specified and directed.

S&F modular socket, 6A-2/3 pin combined 2 module complete all as specified and directed.

S&F modular socket, 6A and 16A, 2/3 pin combined 2 module complete all as specified and directed.

S&F modular switch 1 way 16A, 1 module complete all as specified and directed.

S&F ceiling rose, 3 phase/PVC/polycarbonate, isolated body complete all as specified and directed.

S&F lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F LED bulb 9 watt complete all as specified and directed.

S&F LED batten 20 watt, appx 4 feet long, environment friendly, including electric connection with using 2 core flexible copper conductor cable 23/0.00076 from ceiling rose to tube fitting, complete fitting with all accessories and specifications complete all as specified and directed.

S&F LED batten 20 watt, appx 4 feet long, environment friendly, including electric connection with using 2 core flexible copper conductor cable 23/0.00076 from ceiling rose to tube fitting, complete fitting with all accessories and specifications complete all as specified and directed.

S&F environmental friendly, ultra modern, energy saving, surface mounted, decorative bulk head fitting LED luminaire comprising of high brightness LEDs 10 watt, IP66 protection class complete all as specified and directed. Make Havells Cat Part No. RUGBYGENXFTS10WLED865SSYMBOPC/ Bajaj Cat Part No. BIBWP 10W LED WH/Philips Cat Part No. WT202WLED 10S

S&F surface mounting mirror light fitting 1 ft length, 10/12 watt LED light fitting complete all as specified and directed.

M&L sub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS-H, cable of 2 run 6 Sq mm for phase and neutral and one run of 6 Sq mm for earth wire unsheathed, multistranded, copper conductor FRLS-H, cable drawn through non metallic rigid PVC conduit not less than 20mm dia ISI marked including all conduit and fixing accessories complete. Two runs of cable for phase/neutral, one run of cable for earth and one run PVC conduit will be measured and paid as one unit length complete all as specified and directed. Note:- Wiring shall be done in proper colour coding.

S&F 200mm sweep exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230 V, 50 Hz, RPM 1200, copper winding, 5 star rated complete all as specified and directed. Make: Bajaj, Compton, Havells or equivalent make as approved by GE. Note: Old unsv exhaust fan to be deposited in MES Store yard.

Supplying, fixing, intallating and testing vertical type storage electric water heater (Geyser) of 50 Ltrs capacity, Tank made of ultra thick super cold rolled steel plates with high density PUF insulation, 2 KW, 230V, single phase, 50 Hz, AC, BEE 5 Star rated, suitable for a pressure rating of 0.8 MPa Bar with 7 years warranty on inner tank, 5 years on heating element & 2 years comprehensive warranty with & including connected accessories and 2 Nos anchor fasteners of size as per manufacturer's instructions grouting and fixing and making good the distrubed surface complete and connecting electrical and water supply connection using steel braided hose 2 Nos complete all as specified and as directed. Make of Geyser:- Havells, Model Monza DX, Cat Part No. GHWAMGTWH050/Bajaj Calenta 50 Ltr Note for make of Geyser:- Mentioned above is not available in market then equivalnet price and specification in Racold/CG or as approved by GE. Note: (i) Installed Geyser's warranty card should be submited to the Engineer-in-Charge. (ii) The cost of making good the disturbed surfaces and matching to the existing/orignial surface is deemed to be included in the unit quoted rates.

S&F PVC connection for hot water made of double layer nylon braided and fabric at a pressure of 6 Kg/Sqcm at both ends, 450mm long, heavy duty and with CP brass adopters, washers, suitable for 15mm bore pipe complete all as specified and directed. Make:- Prayag/Polytuff/Shakti

S&F factory made DB SPN 8 way double door with 200 Amps rated bus bar concealed in wall IP 42/43 protection,240V for fixing MCB & making good to disturbed surfaces as well as matching with existing whitewash colour/surface complete all as specified and directed. Note:- Distribution board and MCB's should be same make.

S&F MCB SP ‘B’ curve, 10KA, 240V, 6 to 32 amps, in the MCB DB including necessary connection complete all as specified and directed.

S&F MCB SPN ‘C’ curve, 10KA, 240V, 32 amps, in the MCB DB including necessary connection complete all as specified and directed.

M&L earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connecting to GI earth wire of size 4mm size by means of bolts, nuts, check nuts and protected by provision of GI medium grade pipe of 15mm bore including provision of 40mm tk cover of RCC (1:2:4) reinforced with XPM (wt no less than 4Kg/sqm) and frame of angle iron 40mmx40mmx6mm with 6mm dia MS bar handle made to shape, GI light grade 20mm dia pipe for watering of suitable length placed on tp edge of earth plate, common salt and charcoal filling, with fixing arrangement, funnel, wire mesh and excavation and earthwork in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50m complete all as per plate No. 3 of SSR 2009 Part-I and connecting to earth test point all as specified and directed by Engineer-in-Charge and including testing on completion.

Note:-(i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B1, 80mm thick reinforcement with 8mm TOR steel @ 100 c/c in lieu of CI cover and the rate includes in the unit rate of item. (ii) Earth electrode shall be protected upto test point using necessary arrangement with suitable size GI pipe up to 7.50m and the rate includes in the unit rate of item. (iii) Earth pit chamber and RCC cover shall be painted with red paint over a primer coat and the rate includese in the unit rate of item. (iv) The earth chamber shall be constructed 5m away from the edge of the bldg pit and the cost of the same is deemed to be included in the rate for this item.

Supply and laying or fixing or passing through pipe or laid in trenches, 1100 Volt grade heavy duty cable XLPE insulated, armoured electric cable with aluminium conductor ,cross-sectional area 16 sq.mm 4 core including taking out old unserviceable cable complete all as directed.

Sand cushioning to under ground cable with a layer of sand 8 cm before laying the cable and 15cm after laying the cable (10 cm punned thickness above the top of the upper most cable, total 18 cm), complete all as specified and directed.

M&L old size brick class "B" as in cable protection laid dry,flat,transversally along the length of cable on sand cushioning with width equal to length of the brick complete all as specified and as directed.

S&F 40mm bore galvanised iron, light grade (ISI marked) laid in trenches / fixed on wall / poles etc for protection of cable,,including taking out old tubing complete all as specified and as directed.

S&F steel water tubing, 25 mm bore, galvanised , "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

S&F 25mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for GI tubing complete all as specified and directed.

S&F 20mm size ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210gms), complete all as specified.

Supply & installation of 16M high mast shaft in two section suitbale for 55 m/sec wind speed along with head frame, luminiaries carriage suitable for 08 luminiaries in symmetrical arrangement and other accesories manufactured in factory with raising lowering system comprising double drum winch, 5mm diameter SS wire rope, trailing cable, connector, integral power tool motor, manual handle, junction box, lightining finial, (Wiring material from JB to individual luminiare & MCB in base compartment are not included and are a part of installation), with supply of foundation bolts manufactured from special steel along with nuts, washers, anchor plate and common template and outdoor stand mounted feeder pillar with 32A TPN MCB incomer, single dial time switch, 25A TP contactor for the automatic switching of luminiaries, power tool control with 2 No 9A contactors and raise lower push button, Incoming 35 sq. mm and out going 16 & 2.5sq. mm terminals. 16M High mast of make BAJAJ, Crompton, Philips, Havells or equivalent make as approved by GE.

HIGH MAST SYSTEM MAKE : Bajaj Electricals Ltd/, Crompton, Philips, Havells or equivalent make as approved by GE. Height of mast : 16 Meter No. of Section : Two Material Construction : S355 Grade as per BS-EN10 025 Base dia and top diameter (A/F) : Top : 150mm Botton : 460 mm Cross section of Mast : 20 side polygon Standard for Galvanisation : A per BS EN ISO 1461 Size of Opening and door at base : 1200 x 250 mm Diameter of base plate : 670 mm Thickness of base plate : 25 mm Lighting protection finial : GI single spike of length 1200mm Max. wind speed : 44m/s as per IS 875 (Part III) Number of foundation bolts : 12 Nos PCD of foundation bolts : 590 mm Type / diameter / length of foundation bolts : TS 600/30mm dia/ 850 mm long

FOUNDATION DETAILS 1. Excavation dimensions 2800 x 2800 x 1500mm size 2. Lean Concrete 100 mm thick ( 1: 4: 8) D2 (using 40mm graded Aggregate) 3. Matt bars 12mm dia TMT Bars @ 200C/C both ways in double layers 4. RCC (1: 1.5 : 3) 2600 X 2600 X300MM as in footing 5. RCC (1 : 1.5 : 3) 1000 X 1000 X 1400 MM (1100MM below GL and 300 mm above GL) 6. 8 Nos 16mm dia TMT Bars 4 at corners 4 at centres of pedastal col as main bar with 600mm long craking at bottom over matt bars 7. 16 Nos 12mm dia TMT main bars (4 Nos each at 4 side with 600mm long cranking at bottom over matt bars. 8. 10mm dia TMT bars @ 150mm C/C as Stirrups 9. 300mm dia 850mm long foundation bolts 08 Nos inserted in to 16 mm thick anchoring plate 590mm dia at bottom with pointed galvanised nut one each at bottom and top of plate. 10. Foundaiton bolt min clearance 150mm above pedestal col to rest high mast base plate 25mm thick over the bolts. Galvanished nuts 01 number at bottom of base plate 2 Nos at top of base plate. Note : The unit rate is inclusive of necessary formwork, RFR removal of surplus earth, external finishes and other unforeseen items all as directed by Engr - in- Charge

LUMINAIRES CARRIAGE Material of construction : 50 NB ERW Class B-M.S Pipe Diameter of carriage ring (mm) : 535 mm (ID) Construction : 06 Arm, Welded, 2 Sections Load carrying capacity : 08 Luminaire

TRAILING CABLE Conductor : Copper, 5 core, 2.5 Sqmm Insulation : EPR insulated PCP scheathed No.of circuits per mast : One

WINCH / POWDER TOOL Type /SWL of winch : Double drum, SWL 750 Kg - SGDD Method of Operation : Integral Motor Motor Capacity : 1.0 HP ( Including suitable starter) No of Speeds : 6 Pole, Single speed Torque Limitor ; With Mechanical Tripping Facility

STAINLESS STEEL WIRE ROPE Grade / construction : AISI 316, 7/19 Construction Number of Ropes : Two Continuous Diameter (mm) : 6 mm Breaking load Capacity : 2350 Kg x 2

S&F Bajaj amaze 200w LED flood light , Matt black polyester powder coated with secondary lens optics with LED make lumiled having luminaire efficacy of 130 lm/W. Total of 26,000 Lums +/- 10%. Provided with built in surge protection 5kv and external surge protection of 10kv, having Ingress protection Ip66. Model:- Bajaj amaze- BJFL 200w LED-112984/CG/Philips or equivalent make as approved by GE.

Supply, Installation, commissioning and testing of Aviation obstruction light BGAV302LED make: Bajaj or equivalent Cromptong Greaves / C&S / Insta Power red Painted housing, Red coloured Polycarbonate dome and accessories complete all as specified and directed by Engr in charge (01 Fitting required per high Mast)

Supply Install, commissioning and testing Feeder pillar panel, CPRI Approved, factory made, double door, cubical and pedestal type, compartmentalised design, back door fixed type, fabricated out of 3.15 mm thick CRCA steel sheet, weather/dust/vermin proof, IP 65 protection, suitable spaced totally enclosed in chamber, earthing arrangement, locking arrangement with two No lock with duplicate key duly painted with powder coated paint and providing the following items incl connection of all incoming and outgoing cables using suitable size lugs and glands, danger notice board, panel to be embedded in PCC block complete in all respect all as specified & directed including comprising of following items :-

(i) MCCB 63 A Micro processor relaese, 4 pole, 415 Volts, 25 KA breaking capacity - 01 Nos (ii) Power Contactor 3 pole, AC, 70 Amps, 50 Hz, ML type. (Make : L&T Cat Pat No SS90910 Model : ML-4) - 01 Nos (iii) Timer switch analog time switch type, Make : L&T or equivalent - 01 Nos (iv) Multifunction meter with display parameters for voltage, ampere, PF etc - 01 No (v) Indication lamp (R,Y,B), LED type, with toggle switches - 01 Set. Note :- (i) All type of spares such as glands, lugs, nuts, bolts etc, necessary excavation and earthwork, PCC work and making good disturbed surfaces shall deemed to be included in the quoted unit rate. (ii) Drawing of panel shall be approved by GE before fabrication.Make:- Indoasian/L&T/Schinder or equivalent make as approved by GE.

Supply and laying or fixing or passing through pipe or laid in trenches, 1100 Volt grade heavy duty cable XLPE insulated, armoured electric cable with aluminium conductor ,cross-sectional area 25 sq.mm 4 core including taking out old unserviceable cable complete all as directed.

Supply and laying or fixing or passing through pipe or laid in trenches, 1100 Volt grade heavy duty cable XLPE insulated, armoured electric cable with aluminium conductor ,cross-sectional area 95 sq.mm 3.5 core including taking out old unserviceable cable complete all as directed.

Supplying and laying factory made un-reinforced precast concrete cable cover ISI marked, class LV, type 2, flat, size 250mm x 150mm x 40mm complete all as specified and directed.

M&L cutting existing road n exc. 1.5m wide, depth not exc. 1.5m in soft/disintegrated soil, taking out excavated material including laying 80mm GI pipe light grade over 20cm sand filling, returning, filling in and making up the road surface as per existing finish complete all as specified and directed.

Supplying & laying GI tubing light grade 80mm dia for passing of cable/laid in trenches/fixed on pole/walls/laid under floors/roads including fitting complete all as specified and directed. Note:- Excavation, earthwork shall be measured and paid separately under respective item of schedule.

S&F FPF junction box of size 280mm x 170mm x 105mm internal dimensions with hinged cover and locking arrangement comprising of 2 Nos aluminium bus bar, procelain base grip, procelain fuse connector 4 way with earthing terminal and one MCB SP 10 amp, 10 KA and fixed with set of aluminium clamps of size 40 x 3mm, bolts, nuts and washers for loop in loop out connection complete all as specified and directed.

Material and labour for Earthing complete with galvanised iron earth plate electrode of size 600 x 600 x 6 mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including GI earthing strip 32x6mm by means of GI bolts/nuts/washers and protected by 40 mm bore GI light grade pipe upto test point or upto main switch board / electric equipment / pole / lightning arrestor / HT/LT equipments / GODO switch etc, fixing with 02 Nos nuts and bolts and protection pipe fixed with and including flat iron clamps, bolts, nuts and washers. Earth plate shall be surrounded by alternate packed layer 15 cm thick of charcoal or coke and common salt all around bottom and top. 20 mm bore GI medium grade pipe for watering and including funnel, wire mesh, PCC chamber pit made with PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) including necessary form work, excavation and earth work in any type of soil, returning filling and disposal of surplus soil to a distance not exceeding 50m, Pit cover 40mm thick made with RCC (1:2:4) type B1 (using 20 mm graded stone aggregate) including TMT reinforcement 8mm dia @ 75mm c/c both way, MS handle 12mm dia, cover rest on MS angle iron frame 40x40x6mm embeded in concrete duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified & shown in electrical plate No. 3 of SSR 2009 (Part-I) complete all as specified and as directed by Engineer-in-charge.

Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) Protection pipe and GI earthing strip upto electric equipment from top of earth plate shall be included in the unit rate of this item. (iii) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge.

M/S MALHI CONSTRUCTIONS

M/S THAKUR ENTERPRISES

M/S Bharmouri Construction