Construction of Cultural Cum Community Hall (1000 Capacity) at Santrampur Ta. Santrampur Dist. Mahisagar

No. Figure Amount

1 Excavation for foundation upto 1.50 mt depth including sorting out and 2328.90 Cum 278.06

stacking of useful materials and disposing the excavated stuff within all lead

and lift for soft rock not requiring blasting.

2 Excavation for foundation from 1.50 mt to 3.00 mt. depth including sorting out 1553.10 Cum 651.26

and stacking of useful materials and disposing the excavated stuff within all

lead and lift for Hard rock.

3 Filling in foundation and plinth with sand in layers of 20 cm thickness 225.80 Cum 479.80

including watering, ramming and consolidating etc. complete.

thickness including watering, ramming and consolidation etc. complete.

5 Anti Termite System : P/L of Permanent piping technology Anti Termite 2254.60 Sq.m. 63.63

treatment before flooring work by installing LLDP (Low linear density

Polyethylene) tube of 8 mm O.D.& 6.4 mm I.D. with in Built Pressure

Compensation chip every 30 cm interval in the tube, having working pressure

of 2 kg/cm 2 and release rate of 1.9 ltr/Hour fixed by P-Clip and nails. The

LLDP pipe shall be installed at the entire periphery of the building and at

internal network of building depth of 20 to 200 mm under floor every 2 to

mtr. c/c distance (adjustable as per building layout) & ends of loop pass

through a PVC Elbow of minimum 32 mm ID at junction box of wall and floor

level, entering into a steel reinforced grooved flexible pipe mini. 22 mm LD

leading into junction box and during injecting chemicals for termite control

treatment.

The anti-termite chemical Lmidcloprid 30.5% SC mix as per IS 6313 (part-III)

shall be injected by the pressure pump diluted with water @ 10.5 ml/5ltr of

water at the rate of 2 kg/sq.cm. @ 5 ltr /Smt. the contractor shall submit

approved line plan for piping system and junction boxes dully approved by

Engineer-in-charge with bond of 5 years warranty. (II) Anti Termite chemical

injected area (Chemical injecting including labour cost)

6 Providing and laying controlled cement concrete M-150 and curing complete 167.30 Cum 4022.72

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Foundations and plinth for PCC.

7 Providing and laying controlled cement concrete M-250 and curing complete 662.30 Cum 4734.10

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Foundations, footings & mass concrete.

8 Providing and laying controlled cement concrete M-250 and curing complete 76.31 Cum 7732.37

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Columns upto plinth level.

9 Providing and laying cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 567.96 Cum 3092.22

machine cut stone aggregate 40 mm nominal size) and curing complete

including cost of form work in foundation and plinth.

10 Providing and laying controlled cement concrete M-200 and curing complete 153.92 Cum 7729.18

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Columns for Ground floor.

11 Providing and laying controlled cement concrete M-200 and curing complete 89.30 Cum 7770.72

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Columns for First floor.

12 Providing and laying controlled cement concrete M-250 and curing complete 236.29 Cum 6396.62

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Ground beam and plinth beam.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

13 Providing and laying controlled cement concrete M-20 and curing complete 339.20 Cum 4995.13

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Plinth Slab.

14 Providing and laying controlled cement concrete M-200 and curing complete 160.50 Cum 6364.82

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Beam for Ground floor.

15 Providing and laying controlled cement concrete M-200 and curing complete 292.70 Cum 6406.36

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Beam for First floor.

16 Providing and laying controlled cement concrete M-200 and curing complete 4.90 Cum 6934.10

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Chhajja for Ground floor.

17 Providing and laying controlled cement concrete M-200 and curing complete 3.70 Cum 7952.86

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Lintel for Ground floor.

18 Providing and laying controlled cement concrete M-200 and curing complete 756.30 Cum 6776.77

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Ground floor slab.

19 Providing and laying controlled cement concrete M-200 and curing complete 294.70 Cum 6818.31

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in First floor slab.

20 Providing and laying controlled cement concrete M-200 and curing complete 7.60 Cum 7942.27

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Staircases upto floor two level for Ground floor to

First floor.

21 Providing and laying controlled cement concrete M-200 for R.C.C. work and 23.88 Cum 835.84

curing complete including the cost of form work but excluding the cost of

reinforced concrete work in coping on Ground floor.

22 Providing and fixing 90 cm high Stainless steel railing made from anti 50.20 Rmt. 3719.83

corrosive 304 grade S.S. pipe of 50 mm dia. (16 gauge) as hand rail with S.S.

304 grade baluster of 38 mm dia. (16 gauge) as a vertical support fixed in

RCC slab at 1.2m c/c including three horizontal S.S. pipes of 25 mm dia. (16

gauge) at equal distance fixed by 18.75 mm dia (16 gauge) S.S. pipe with

baluster including accessories as per detailed drawing as directed etc.

23 Providing I.S.I. Mark T.M.T. bar Fe-500D reinforcement for R.C.C. work 255689.10 Kg. 77.29

including bending, binding and placing in position complete upto floor two

level for Ground floor.

24 Providing I.S.I. Mark T.M.T. bar Fe-500D reinforcement for R.C.C. work 96409.00 Kg. 78.34

including bending, binding and placing in position complete upto floor two

level for First floor level.

25 Providing and fixing eco-friendly light weight calcium silicate false ceiling tiles 1049.60 Sq.m. 1674.15

having Tegular edge & 15 mm Thick Densified edges on the Tile Periphery

for extra strength. The Light weight calcium silicate ceiling tiles shall have,

light reflection 85% non-combustible as per B.S. 476 part IV, 100% humidity

resistance and also having thermal conductivity 0.043° w/m KC.for the best

thermal Insulation. The Light weight calcium Silicate tile shall be of approved

texture Fine fissured/ Spintone/ Cosmos having NRC value of 0.5 & Globe

having NRC value of 0.75 NRC or equivalent of size 595 x 595 mm to be laid

on true horizontal level suspended inter locking metal grid of hot dipped

galvanized steel sections (galvanizing @120 grams per sqm including both

side) consisting of main ‘T’ runner suitably spaced at joints to get required

length and size of 24 x 38mm made from 0.30 mm thick (minimum) sheet,

1200mm centre to centre, and cross ‘T’ of size 24 x 28mm made out of

0.33mm (Minimum) sheet spaced 1200mm along spaced between main 'T' at

600mm centre to centre to form a grid of 1200 x 600mm and size 24 x 48mm made of

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

0.30mm thick (Minimum) sheet to be interlocked at middle of the 1200 x

600mm panel to form grid of size 600 x 600mm resting on periphery

walls/partitions on a perimeter wall angle pre-coated steel of size (24 x 24 x

3000mm made of 0.40mm thick (minimum) sheet with the help of rawl plugs

at 450mm centre to centre with 25mm long dry wall screws @ 230mm interval

and laying 15mm thick densified edges light weight calcium silicate ceiling

tiles of approved texture (Fine fissured / Cosmos / Spintone) in the grid

including cutting / making opening for services like diffusers, grills, light

fittings, fixtures, smoke detectors etc., whenever required, Main 'T' runners to

be suspended from ceiling using G.I. slotted cleats of size 25 x 35 x 1.6mm

fixed to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm G.I.

adjustable rods with galvanized steel level clips of size 85 x 30 x 0.8mm,

spaced at 1200mm center to centre long main 'T' bottom exposed with 24mm

of all T-sections and also provide additional frame work and

suspended G.I. support as required height shall be pre-painted with polyester

baked paint, for all heights, as per specifications, drawings and as directed by

engineer-in-charge. Note:- Only calcium silicate false ceiling area will be

measured from wall to wall. No deducation shall be made for exposed

frames/opening (cut outs) having area less than 0.30sqm. The calcium

silicate ceiling tiles shall fissured / Spintone / Cosmos and 0.75 NRC for

Globe, light reflection 85% non-combustible as per B.S. 476 part IV, 100%

humidity resistance and also having thermal conductivity. 0.043 w/m KC for

the best thermal Insulation.

26 Providing and laying brick work using common burnt clay building 163.10 Cum 4214.33

conventional type bricks having crushing strength not less than 35 Kg./Sq.cm.

in foundation and plinth in cement mortar 1:6 (1 cement : 6 fine sand)

including the cost of all materials and labour charges etc. complete.

27 Providing and laying brick work using common burnt clay building 919.56 Cum 4496.05

conventional type bricks having crushing strength not less than 35 Kg/sq.cm.

in super structure above plinth level upto floor two level in cement mortar 1:6

(1 cement : 6 fine sand) for Ground Floor including the cost of all materials

and labour charges etc. complete.

28 Providing and laying brick work using common burnt clay building 809.70 Cum 4538.16

conventional type bricks having crushing strength not less than 35 Kg/sq.cm.

in super structure above plinth level upto floor two level in cement mortar 1:6

(1 cement : 6 fine sand) for First Floor including the cost of all materials and

labour charges etc. complete.

29 Providing and laying brick work using common burnt clay building 32.20 Cum 4580.28

conventional type bricks having crushing strength not less than 35 Kg/sq.cm.

in super structure above plinth level upto floor two level in cement mortar 1:6

(1 cement : 6 fine sand) for Second Floor including the cost of all materials

and labour charges etc. complete.

30 Providing and laying half brick work using common burnt clay building 218.40 Sq.m. 680.52

conventional type bricks having crushing strength not less than 35 Kg/Sq.cm

in cement mortar 1:4 (1 cement : 4 coarse sand) in cement mortar in super

structure for Ground floor including the cost of all materials and labour

charges etc. complete.

31 Providing and fixing 150 mm wide, approved quality chicken wire mesh at 326.90 Sq.m. 295.12

junction of brick work and RCC work or two dissimilar surfaces, at all heights

fixed by nails, rowal plugs or tag by cement mortar 1:3 before applying the

plaster, including curing etc. complete

32 Providing 15mm thick cement plaster in single coat on rough (similar) side of 1425.80 Sq.m. 226.01

single or half brick walls / concrete wall for interior plastering and finished

even and smooth along with floating coat of neat cement slurry etc. complete

in Cement mortar 1:4 (1-cement : 4 sand) at Ground floor.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

33 Providing 15mm thick cement plaster in single coat on rough (similar) side of 578.50 Sq.m. 249.90

single or half brick walls / concrete wall for interior plastering and finished

even and smooth along with floating coat of neat cement slurry etc. complete

in Cement mortar 1:4 (1-cement : 4 sand) at First floor.

34 Providing 10 mm. thick smooth cement plaster in single coat for plastering on 1310.70 Sq.m. 208.97

ceiling and soffits of stairs and finished even and smooth along floating coat

of neat cement slurry in cement mortar 1:4 (1 cement : 4 sand) (1) Plaster at

Ground floor.

35 Providing 10 mm. thick smooth cement plaster in single coat for plastering on 1820.60 Sq.m. 230.86

ceiling and soffits of stairs and finished even and smooth along floating coat

of neat cement slurry in cement mortar 1:4 (1 cement : 4 sand) (1) Plaster at

First floor.

36 Providing 20mm thick double coat sand faced cement gutka plaster on walls 2162.90 Sq.m. 345.75

with 1 x 1 cm grooves consisting of 12 mm thick backing coat of C.M. 1:3 (1

cement : 3 sand) and 8 mm thick finishing coat of C.M. 1:1 (1 cement :

sand) including 1 cm x 1 cm grooves etc. complete as directed by Engineer-

in-charge.

37 Providing throating or plaster drip and moulding to R.C.C. Chhajja. 64.20 Rmt. 43.05

38 Applying two coats of acrylic lappy - putty & two coats of primer of approved 4924.60 Sq.m. 40.59

brand and manufacture on new wall surface to give an even shade including

thoroughly brushing the surface free from mortar dropping and other foreign

matter and sand papered smooth for all floors.

39 Wall painting (two coats) with plastic emulsion paint of approved brand and 1879.30 Sq.m. 82.85

manufacture on undecorated wall surfaces to give an even shade including

thoroughly brushing the surface free from mortar droppings and other foreign

matter and sand papered smooth for all floors.

40 Wall painting (two coats) with plastic emulsion paint of approved brand and 3045.30 Sq.m. 88.38

manufacture on undecorated ceiling surface to give an even shade including

thoroughly brushing the surface free from mortar droppings and other foreign

matter and sand papered smooth for all floors.

41 Finishing wall with weather proof exterior 100% acrylic emulsion paint with 3672.70 Sq.m. 120.26

one coat of primer on wall surface to give an required shape even shade after

thoroughly brushing the surface to remove all dirt, dust and remains of loose

powdered materials etc. complete for all floors.

42 Providing and filling with good quality sinder (steam coal) as directed by 42.50 Cum 572.06

engineer in charge in sunks in layers of 15 cm thick including watering,

placing, ramming well etc. as directed for all floors.

43 Providing and fixing Double Shutter Toughened Glass Door comprising 12 63.00 Sq.m. 3713.50

mm thick clear toughened glass shutters, complete with approved make

stainless steel patch fittings, pull handles, floor spring, top and bottom pivots,

locks, connectors, and all other necessary stainless steel fixtures and

accessories. The door shall be installed with silicon gaskets / sealant to

ensure airtight fixing and proper alignment. The work shall include all cutting,

drilling, edge polishing, hardware fixing, installation, testing, and

commissioning, complete in all respects as per approved drawings and site

requirements.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

44 Providing and fixing single shutter flush shutter comprising anodized / powder 35.70 Sq.m. 4693.82

coated extruded aluminum section frame, equivalent to Jindal Door Section

No. 19552, having minimum weight not less than 1.10 kg per running meter,

of size 38 mm x 63.5 mm, complete with wooden inserts for proper gripping

and durable fixing of door hinges, fixed in position complete. The door shutter

shall be 38 mm thick solid core flush door shutter, made with first class

hardwood, covered on both sides with approved plywood face panels,

finished with 1.00 mm thick decorative laminate on both faces, fixed with

necessary adhesive, screws and fittings, complete. The item shall further

include S.S. door handles (AISI 304 grade), S.S. aldrop, S.S. door stopper,

approved locking arrangement, S.S. hinges, and all other required hardware

and accessories, complete in all respects. Colour and shade of laminate and

aluminum frame shall be as approved by the Engineer-in-charge. The rate

includes cost of all materials, labour, fabrication, fixing, fittings, fasteners,

adhesives and finishing, complete as per drawings,

specifications and directions of the Engineer-in-charge.

45 Providing and fixing Four Track Sliding Aluminium Window comprising three 99.80 Sq.m. 2030.82

glazed sliding shutters and one sliding mosquito mesh shutter, fabricated

from colour anodized aluminium extruded sections equivalent to Jindal Series-

E (30 mm), using frame sections : bottom with gutter-21198 and top & side-

21204, shutter sections: top & bottom-20993, interlock-20550, and side

(handle)-20553. The glazed shutters shall be fitted with 5 mm thick

transparent tinted float glass, and the mosquito mesh shutter shall be

provided with approved quality mosquito net fixed in aluminium frame. The

work shall include rubber gaskets, air-lock strips, transparent silicone sealant

at joints, colour anodized aluminium fittings and fixtures, rollers, handles,

locks, and all necessary accessories for smooth and efficient operation. The

item shall be installed complete in all respects as per approved drawings,

specifications and site requirements.

46 Providing & fixing in position standard extruded approved colour anodized 11.60 Sq.m. 3866.85

Alluminum Ventilator with 5mm thick Bajari figure adjustable tinted louvers

glass fixed to alluminium strip blade including fixtures, fastening, labours and

equipments as per detailed drawing as directed. For Ventilators.

47 Providing and laying Machine cut, free edges, mirror polished Granite Slab 559.60 Sq.m. 2363.13

flooring over 18mm (Average) thick base of cement mortar 1:6 (1-cement : 6-

coarse sand) laid over and jointed with grey cement slurry mixed with pigment

to match the shade of slab including rubbing and polishing etc. complete. (A)

18mm thick. (Flooring Type : 01)

48 Providing and laying machine cut, free edges, mirror polished Granite Slab 22.60 Sq.m. 4112.46

18mm thick in risers of steps, skirting, dedo and pillars laid on 10mm thick

cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with gray cement

slurry mixed with pigment to match the shade of slab including rubbing and

polishing etc. complete. (Flooring Type : 01)

49 Providing and laying Double Charge Vitrified tiles of approved make and 1245.30 Sq.m. 1187.86

shade having a thickness of 8mm to 10mm and size 0.80m x 0.80m (32" x

32") in flooring treads of steps and landing laid on a bed of 12mm thick

cement mortar 1:3 (1 cement : 3 coarse sand) finishing with flush pointing in

white cement. (Flooring Type : 02)

50 Providing and laying readymade full body vitrified step tiles, 10 mm to 12 mm 25.30 Sq.m. 1262.50

thick of approved make and shade, consisting of 120 x 30 cm tiles for tread,

120 x 15 cm tiles in skirting risers of steps and dedo on 10mm thick cement

plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement slurry.

(Flooring Type : 02)

51 Providing and laying Ceramic tiles 60 cm x 60 cm and 6mm thick in flooring 118.70 Sq.m. 1037.98

treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1-

cement : 3-coarse sand) finishing with flush pointing in white cement.

(Flooring Type : 04)

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

52 Providing and laying printed coloured glazed tiles of the size 300 mm x 200 719.30 Sq.m. 1488.24

mm x 8 mm / 300 mm x 450 mm x 8 mm in skirting, risers of steps and dedo

on 10 mm. thick cement plaster 1:3 (1 cement : 3 coarse sand) & jointed with

white cement slurry. (Flooring Type: 04)

53 Providing Plinth Protection to building including excavation and laying cement 120.00 Sq.m. 1782.28

concrete 1:3:6 using stone aggregates of 40mm nominal size in foundation

layer 150 mm thick+ 125mm thick sand layer below precast rubber dye inter

locking concrete block 60mm thick with grade of concrete M-300 pneumatic

compressed by mechanically pressed and as per approved design including

75mm sand layer for levelling and filling the joint with sand in proper line and

level etc. complete including providing and fixing precast concrete kerb stone

of grey cement based concrete block 30cm length, 30cm height and 15cm

thick made of M-250 grade concrete as per approved design and including

excavation for fixing in proper line and level, filling the joint with C:M 1:3 (1

cement : 3 fine sand) etc. complete. (Flooring Type: 05)

54 Providing and laying broken china mosaic flooring for terrace using 12 mm to 1633.20 Sq.m. 779.70

20 mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to

plain or slope and to be tempered to bring mortar creme out upto surface

using white cement including rounding off junctions and extending them upto

15 cm along the wall, clearing with water and oxalic acid etc. as directed.

(Flooring Type: 06)

55 Providing and laying ready made full body vitrified step tiles, 10 mm to 12 mm 15.40 Sq.m. 1262.50

thick, of approved make and shade, consisting of 120 x 30 cm tiles for tread,

120 x 15 cm tiles for riser and 60 x 60 cm tiles for landing, with factory-made

half-round nosing and anti-skid flutes to tread portion, laid over 12 mm thick

cement mortar bed in proportion 1:3 (1 cement : 3 coarse sand), including

necessary cutting, leveling, curing, and finishing the joints with white cement

slurry, including 7.5 cm high skirting of same tiles, complete in all respects,

as approved by the Engineer in charge / this office. (Flooring Type: 07)

56 Providing and laying cement concrete flooring 1:2:4 (1 cement : 2 coarse 1656.00 Sq.m. 347.42

sand : 4 graded stone aggregate 20mm nominal size) laid in one layer and

finished with a floating coat of neat cement. (B) 50 mm thick.

57 Providing and fixing mirror polished 18mm thick Granite with full round edge 99.00 Sq.m. 2553.90

and polished of approved quality in cladding on sill and around the doors /

windows / ventilation with 20 mm thick cement plaster CM (1:4) and fixing

with cement slurry & adhesive including moulding of exposed edges as

directed by engineering in charge etc. complete.

58 Providing and fixing M.S. Grills of required pattern to frames of windows etc. 111.30 Sq.m. 3095.77

with M. S. flats at required spacings and frame alround having min. weight of

grill 25 kg/sq.m, square or round bars with round headed bolts and nuts or by

screws including priming coat of approved quality and two coats of enamel

paint, as directed by engineer in charge (A) Plain grill.

59 Providing, erecting and fixing double coated I.S.I. Mark P.V.C. water tank of 10000.00 Litre 3.95

required capacity each with all necessary fittings and connection etc.

complete on terrace as directed.

60 Providing, laying and jointing in true line and level I.S.I. mark 110mm dia. 388.00 Rmt. 876.90

U.P.V.C. pipe (Type B) confirming to IS 13592-1992 with one end plain and

other end socketed with rubbering & fitting conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall be jointed with each

other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of

the size 110 mm diameter x 149 mm length x 145 mm height at every

mm center to center or shall be concealed in walls as directed including

necessary fittings such as bends, shoes etc. including testing of pipes and

joints and jointed with adhesive solvent cement including cost of all materials.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

61 Providing, laying and jointing in true line and level I.S.I. mark 160mm dia. 216.00 Rmt. 834.38

U.P.V.C. pipe (Type B) confirming to IS 13592-1992 with one end plain and

other end socketed with rubbering & fitting conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall be jointed with each

other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of

the size 160 mm diameter x 210 mm length x 196 mm height at every

mm center to center or shall be concealed in walls as directed including

necessary fittings such as bends, shoes etc. including testing of pipes and

joints and jointed with adhesive solvent cement including cost of all materials.

62 Providing, laying and jointing in true line and level I.S.I. mark 50mm dia. 242.00 Rmt. 195.67

U.P.V.C (Sch-40) for cold water including fitting as approved by Engineer in

charge. Pipe shall be fixed on the wall with held of clamp at every two meter

c/c shall be concealed or open as directed including necessary fitting etc.

including testing of pipe and joints and fixing the same with adhesive solvent

including cost of all materials.

63 Providing, laying and jointing in true line and level I.S.I. mark 40mm dia. 192.00 Rmt. 148.12

U.P.V.C (Sch-40) for cold water including fitting as approved by Engineer in

charge. Pipe shall be fixed on the wall with held of clamp at every two meter

c/c shall be concealed or open as directed including necessary fitting etc.

including testing of pipe and joints and fixing the same with adhesive solvent

including cost of all materials.

64 Providing, laying and jointing in true line and level I.S.I. mark 25mm dia. 240.00 Rmt. 91.84

U.P.V.C (Sch-40) for cold water including fitting as approved by Engineer in

charge. Pipe shall be fixed on the wall with held of clamp at every two meter

c/c shall be concealed or open as directed including necessary fitting etc.

including testing of pipe and joints and fixing the same with adhesive solvent

including cost of all materials.

65 Providing, laying and jointing in true line and level I.S.I. mark 15mm dia. 240.00 Rmt. 72.65

U.P.V.C (Sch-40) for cold water including fitting as approved by Engineer in

charge. Pipe shall be fixed on the wall with held of clamp at every two meter

c/c shall be concealed or open as directed including necessary fitting etc.

including testing of pipe and joints and fixing the same with adhesive solvent

including cost of all materials.

66 Providing and fixing concealed center point to wall ceiling & floor I.S.I. mark 240.00 Rmt. 447.72

C.P.V.C. (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal

for potable water of following dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and floor etc. complete. (E) 40mm dia.

67 Providing and fixing concealed center point to wall ceiling & floor I.S.I. mark 240.00 Rmt. 253.82

C.P.V.C. (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal

for potable water of following dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and floor etc. complete. (C) 25mm dia.

68 Providing and fixing concealed center point to wall ceiling & floor I.S.I. mark 240.00 Rmt. 170.36

C.P.V.C. (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal

for potable water of following dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and floor etc. complete. (A) 15mm dia.

69 Providing and laying (to level or slopes) and jointing reinforced concrete light 400.00 Rmt. 678.02

duty non pressure pipes I.S. Class NP-2 of the following internal diameter

with collars and butt ends prepared for collar joints including testing of joints

complete. (D) 300mm dia.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

70 Providing, laying and jointing in true line and level I.S.I. mark 75mm dia. 240.00 Rmt. 756.22

U.P.V.C. SWR Type B pipe confirming to IS 13592-1992 with one end plain

and other end socketed with rubbering and fitting conforming to ISI 14735-

1999 of approved make for drainage system pipe line, pipe shall be jointed

with each other with rubber lubricant, pipe shall be fixed on wall using of PVC

clamp at every 2000 mm c/c or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc. including testing of

pipes and joints and jointed with adhesive solvent cement including cost of all

materials.

71 Providing and fixing cast iron spigot and socket soil, waste and ventilating 40.00 No. 741.01

pipes of the following nominal size. (B) 75mm dia.

72 Providing and fixing cast iron spigot and socket soil, waste and ventilating 40.00 No. 892.39

pipes of the following nominal size. (C) 100mm dia.

73 Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm 16.00 No. 586.27

diameter with jali of the following nominal diameter of self cleaning design

with C.I. screwed down or hinged grating including the cost of cutting and

making good the walls.

74 Providing and fixing wash down water closet (European type W.C. pan) with 10.00 No. 3631.34

integral P and trap including jointing the trap with soil pipe in cement mortar

1:1 (1 cement : 1 fine sand) including providing and fixing plastic seat cover

for wash down WC with CP brass hinges and rubber buffers back plastic seat

and including providing and fixing PVC flushing tank with a pair of C.I. or M.S.

bracket with complete fitting such as lead valve siphon 15 mm dia. brass ball

valve with polythene float C.P. brass handle unions and couplings for

connection with inlet out let and over flow pipes 40 mm dia. porcelain

enameled flush bend including cutting holes in walls and making good the

same connection the flush bend with cistern and closet vitreous china etc.

completed.

75 Provision, supplying and fixing white vitreous china W.C. squatting pan Orrisa 8.00 No. 1638.03

type 580 x 400 size with 100mm P or S trap, 25mm dia. C.P. Brass flush

valve and G.I. inlet connection etc. complete. (A) Vitreous china long pattern

white or color.

76 Providing and fixing brass screw down stop tap. (A) 15mm dia. as approved 36.00 Each 205.83

by Engineer in charge.

77 Providing and fixing ball cock of approved quality as directed. (A) Copper 4.00 Each 189.84

Metal (iv) 50mm dia.

78 Providing and fixing wash basin with single hole for pillar tap with C.I. or M.S. 18.00 Each 1451.48

brackets painted white including sutting holes and making good the same but

excluding fittings. (A) Vitreous China (ii) Flat Back washbasin 550 mm x

400mm size. (i) In white colour.

79 Providing and fixing C. P. brass waste for wash basin or sink. (A) 32mm dia. 18.00 Each 67.91

80 Providing and fixing M.I. fisher union for washbasin or sink. (A) 32mm dia. 18.00 Each 78.75

81 Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass 18.00 Each 859.41

mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden

plug with C.P. brass screws and washers.

82 Providing and fixing screw down bib taps of following size.(A) Brass screw 36.00 Each 214.81

down bib tap polished bright. (ii) 20mm dia. as approved by Engineer in

83 Providing and fixing pillar tap, capstan head, screw down high pressure with 18.00 Each 308.73

screws, shanks and back nuts. (i) 15mm dia. as approved by Engineer in

84 Providing and fixing in position 300 mm high, 300 mm wide English / Gujarati 40.00 Each 707.00

letters made from 1.0 mm thick stainless sheet as directed by Engineer-in-

charge with all necessary tools & plants etc. complete.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

85 Providing and fixing Urinal of approved quality including connection with trap 13.00 Each 1635.22

and with integral longitudinal flush pipe. (A) Squatting plate pattern white

earthenware 550mm x 300mm.

86 Providing and fixing Rubber plug for sink or wash basin. 31.00 Each 17.15

87 Providing and fixing chromium plated brass half turn flush cock of approved 10.00 Each 263.77

quality including fixing in pipe line etc. complete (ii) 25mm dia.

88 Providing and fixing S.W. Gully trap with C.I. grating brick masonry chamber 8.00 Each 1246.92

and water tight C.I. cover with frame of 300 x 300 mm size (inside) with

standard weight (i) square mouth traps (B) 150 mm x 100 mm size P or R

89 Constructing brick masonry chamber for underground C.I. Inspection 8.00 Each 2932.93

chamber and bends with bricks having crushing strength not less than

Kg/cm2 in C.M. 1:5 C.I. cover with frame (light duty) 455mm x 610mm internal

dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of

cover 23 Kg.) and Wt. of frame 15Kg.) (R.C.C. top slab with 1:2:4 mix (1-

cement : 2 coarse sand : 4 graded stone aggregate 20mm size) foundation

concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement on walls and bed concrete etc.

complete. (i) Inside dimensions 455mmx 610mm and 450mm deep for single

pipe line.

90 Constructing brick masonry chamber for underground C.I. Inspection 15.00 Each 3660.76

chamber and bends with bricks having crushing strength not less than

35Kg/Cm2 in C.M. 1:5 C.I. cover with frame (light duty) 455mm x 610mm

internal dimensions total weight of cover with frame to be not less than 38Kg.

(Wt. of cover 23 Kg.) and Wt. of frame 15Kg.) (R.C.C. top slab with 1:2:4 mix

(1-cement : 2 coarse sand : 4 graded stone aggregate 20mm size) foundation

concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement on walls and bed concrete etc.

complete. (ii) Inside dimensions 500mm x 700 mm and 450mm deep for pipe

line with one or two inlets.

91 Providing cement vata (10cm x 10cm size) quarter round in cement mortar 70.50 Rmt. 24.28

1:1 including neat cement finishing watering etc. complete.

92 Providing and fixing in position collapsible steel shutters with vertical 3.70 Qtl. 6076.50

channels 20 x 10 x 2 mm braced with flat iron diagonals 20 x 5 mm size with

top and bottom rails of T_rin 40x 40 x 6 mm with 38mm dia, steel pulleys

complete with bolts, nuts, locking arrangements, stoppers, handles including

applying a priming coat of red lead paint.

93 Providing and fixing in position 150 mm high, English letters made from 1.0 30.00 Each 404.00

mm thick stainless steel sheet as directed by Engineer in charge with all

necessary tools & plants etc. complete.

94 Providing and fixing polished 18 mm thick black granite with full round edge 4.50 Sq.m. 2719.93

and double side polished of approved quality in between urinal and fixing with

cement slurry & adhesive including moulding of both exposed edges as

directed by engineering in charge etc. complete.

95 Providing & fixing 114mm wide G.I. Sheets louvers having weight not less 45.90 Sq.m. 7824.47

than 490 Gm/m roll formed to create 84mm wide louver snap fixed on special

shaped GI channel. Fix louvers & channels shall finished with powder coating

of 55 micron (1) 0.55mm thick sheet etc. complete as per detail drawing as

96 Providing and fixing tiles roofing with manglore tiles of approved quality, color 1347.80 Sq.m. 93.56

and make, conforming to IS: 654, laid over a prepared RCC sloping slab or

Chhajja. The tiles shall be embedded firmly in a cement mortar bed of 1:4 (1

cement : 4 coarse sand) mix of minimum 20 mm thickness, including carefully

removing or leveling bottom lugs to fit flush on the slab, neat interlocking,

maintaining true grid alignment, filling joints tightly with matching colored

cement grout, providing wet curing for a minimum of 7 days, scaffolding,

lifting materials to all levels, cleaning the surface post installation and making

the roof completely watertight complete as directed by the Engineer-in-charge.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

97 Providing and fixing Cement Fiber Sheet with CNC cutting in standard 205.60 Sq.m. 4336.55

extruded of alluminium colour anodized section frame main outer pipe centre

to centre pipe 75cm of size 50 x 38.10 x 1.95 mm (of @ Wt 0.643 Kg/Rmt)

detail drawing and as directed by Engineer in charge.

98 Clearing and grubbing road land including uprooting rank vegetation grass 2.30 Hect. 28455.09

bushes, shrubs, sapling and trees girth up to 300 mm removal of stumps of

trees cut earlier and disposal of unserviceable materials (C) By mechanical

means in area of light jungle.

99 Earthwork in cutting including preparing the slope, camber and stacking or 46046.00 Cum 317.35

utilising the cutting stuff in bank as directed upto 200 meters from the end of

cutting with all lead and lift. (ii) Soft rock not requiring blasting.

100 Rolling and watering of earthwork in layers with power roller including filling in 9986.00 Cum 22.96

depressions which occur during the process as directed by Engineer

101 Box cutting the road surface to proper slop and camber for making a base of 1140.50 Cum 109.41

road work including removing the excavated stuff and depositing on the road

side slope as directed for all lead and lift.

102 Providing and laying compacted WBM of Grading-II MCBT metal of size 45 to 403.00 Cum 1851.33

63mm in required layers including using 13% stone screening, 13.2mm size

and 7% stone dust as filler including spreading, watering & consolidation by

vibratory roller etc. complete.

103 Providing and laying controlled cement concrete M-200 and curing complete 707.28 Cum 4204.41

including the cost of formwork and excluding reinforcement for reinforced

concrete work in (A) Foundations, footings and Mass concrete.

104 Compaction and finishing of cement concrete road by trimix process 2684.00 Sq.m. 65.65

providing extra labour charges for the trimix vacume dewatering service

process on cement concrete road surface by using vacuum dewatering pump

floater surface vibrator including making grooves and rough finish to surface

including leveling etc. complete.

105 Providing and laying homogeneous grey cement based concrete kerbing of 818.00 Rmt. 374.92

size 30 cm x 30 cm x 10 cm size as per detailed drawing having grade of

concrete M-25 grade, including necessary excavation, BBCC 1:5:10, 7.5 cm

as per detailed drawing fixing in line and level, filling joints in C.M. 1:3 with

smooth finished, white washing three coats etc. complete as directed by

Engineer in charge.

106 Supplying premoulded bituminous joint filler 12 mm thick. 50.00 Sq.m. 553.79

107 Providing, laying (to level or slopes) and jointing reinforced concrete light duty 60.00 Rmt. 659.99

non-pressure pipes I.S. class NP3 of the following internal diameter with

collars and butt ends prepared for collar joints including testing of joints

complete. (i) 300mm

108 Providing & laying Rain Water Junction Chamber of clear internal size 0.60 x 20.00 No. 7514.23

0.60 x 0.75m with excavation of size 1.36 x 1.36 m & 0.15m thick M-200 bed

concrete including brick masonary 0.23 thick wall in C.M. 1:6 of 0.75m height

with 15mm thick cement plaster inside & outside (1:4), 1.06 x 1.06 RCC M-

200 top slab of thickness 0.15m with TMT steel and 455mm x 610mm cast

iron manhole cover with frame weight not less than 35 kg as per directed by

Engineer-in-charge.

109 Providing & laying Filter chamber of brick work 0.23 thick in C:M 1:6 of clear 2.00 No. 25919.35

internal size 2.04 mx 1.20 m x 1.20m and excavation dimension of 2.80m x

1.96 x 1.35m including C.C. M-200 bed concrete of 0.15m thick and RCC M-

200 top slab of thickness 0.15m with TMT steel, including 15mm (1:4) thick

cement plaster inside & outside with cement slurry & top cover with frame of

minimum weight of 35 kg. including filling filter material of 200mm thick each

layer of 25-40mm, 10-20mm of B.T. metal and Sand as per directed by

Engineer-in-charge.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

110 Providing & laying Water harvesting pit of clear size 2.00 mt x 2.00mt x 4.00 1.00 No. 30055.01

mt. for water logging with excavation in any strata upto four meter depth, brick

work 0.23 thick in C:M 1:6 of clear internal Size 2.00 m x 2.00 m x 1.20m with

15mm thick C:M 1:4 plaster, filling the pit with B.T. Metal 40 mm in 0.60 mt.

depth with 25-40mm kapachi, 0.30 mt. depth and 2.0 mt. depth with coarse

sand in layers including making P.V.C. line for water inlet etc. as directed with

250mm dia bore 15 mt. depth and 150mm dia P.V.C. pipe of 10 Kg.f/Cm2

casing with gravel packing or as directed.

111 Excavation for foundation upto 1.5 mt. depth including sorting out and 898.16 Cum 256.12

stacking of useful materials and disposing off the excavated stuff upto

Meter lead.(C) Hard Murrum.

112 Excavation for foundation for depth from 1.5 mt. to 3.0 mt. including sorting 273.92 Cum 287.48

out and stacking of useful materials and disposing off the excavated stuff

upto 50 Meter lead. (D) Soft rock not requiring blasting

113 Filling available excavated earth (excluding rock) in trenches plinth side of 570.22 Cum 136.92

foundation etc. in layer not exceeding 20 cm in depth consolidation each

deposited layer by ramming and watering etc. complete.

114 Providing 15 mm. thick cement plaster in single coat on brick/concrete wall 1509.80 Sq.m. 226.01

for interior plastering upto floor two level finished even and smooth in (C.M.

1:3) finishing with a floating coat of neat cement slurry.

115 Providing and fixing 610mm dia. Barbed Razor Tape Concertina Coil made 535.00 Rmt. 258.58

from hot dip galvanized spring steel high tensile wire (UTS: 145-160Kg/Cm2,

Zncoating 250-300g/m2, Diameter- 2.59+/-0.05mm), with blade of galvanized

Iron of 0.50 mm thick and width 19mm, with coverage / openable length of

10mtr/coil, including providing and fixing with clips, wires, bolt set con M.S.

angle posts, with all materials, labour, tools, tackles, etc. as per direction of

Engineer In-charge, for work at all level.

116 Providing and laying cement concrete 1:4:8 (1- Cement : 4- coarse sand : 8 100.00 Cum 2766.67

hand broken stone aggregates 40 mm nominal size) and curing complete

excluding cost of formwork in (A) Foundation and Plinth

117 Steel work, welded in built up sections framed work including cutting, 19720.00 Kg. 91.08

hoisting, fixing in position and applying a priming coat of red lead paint & two

coat oil paint. (A) In beams and joists, channels angles Tees, flats, with

connecting plates or angle cleats as in main and cross beams. Hip and jack

rafters, purlins connected to common rafters and the like.

118 Providing corrugated double coated trafford sheet roofing fixed with 986.00 Sq.m. 1022.80

glavanished iron J or L hooks, bolts and nuts 8mm diameter with bitumen and

G.I. limpet washer or G.I. limpet washer filled with white lead complete

excluding the cost of purlins, rafters and trusses. (1) 0.80 mm thick sheet.

119 Providing and fixing precast Rubber Dye / steel dye inter locking concrete 936.00 Sq.m. 706.77

block 60mm thick with grade of concrete M-300 pneumatic compressed /

vibrated mechanically and as per approved design confirming to IS 15658 :

2006 including 35 mm sand layer for levelling and filling the joint with sand in

proper line and level as per guidlines of IRC : SP 63-2018 etc. complete.

120 Drilling of pilot bore hole of size 250 / 300 mm diameter at above site by mud 150.00 Mtr. 865.57

finish direct rotary rig etc. complete.

121 Reaming of 250 / 300 mm diameter pilot bore hole to size 450 mm diameter 150.00 Mtr. 398.95

including assembling, lowering housing, casing strainer pipes with gravel

packing and clay ball packing etc. complete.

122 Providing 600 CFM / 150 PSI capacity air compressor up to availability of 1.00 Job 22427.05

sand free discharge (Minimum 6.0 Hours)

123 Supply of reducer made from 6 mm thick plate (M.S.) for ERW pipe of size (ii) 1.00 No. 1884.27

200 mm dia. x 250 mm dia. x 600 mm length

124 Supply of 200 mm diameter V-wire screen pipe of slot size 1.0 mm nominal 12.00 Mtr. 1767.28

hole etc. complete

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

125 Supply of M.S. bore clamps with 3 holes on either side with nuts and bolts of 1.00 Pair 1643.99

standard make and suitable size (g) 750mm x 75 mm x 16 mm flat to 200 mm

dia. pipe.

126 Supply of Bore Plug having 100 mm height made from M.S. plate with 3 holes 1.00 No. 782.57

at equal distance on circumference for nut- bolts type, locking arrangement

with nut- bolts & lock nuts of standard make complete. (B) from 5 mm thick

M.S. plate (for top also) (ii) suitable for 200 mm dia. pipe.

127 Supply of M.S. Bail Plug having length of 0.45 mtr from medium class pipe as 1.00 No. 851.04

per I.S.S. suitable for (d) 200 mm diameter pipe etc. complete.

128 Supply of Steel Bent plates suitable to ERW pipe for (b) 200 mm diameter 4.00 No. 67.26

and 150 x 150 x 6 mm size etc. complete.

filling etc. complete.

130 Charges for uptron make Electrologger (with carting) of pilot bore hole etc. 1.00 Hour 12120.00

131 Charges for Geo Hydrological ground water investigation including water 1.00 Job 14428.86

sample chemical analysis etc. complete.

132 Supplying submersible pump set suitable for bore of 150 mm. dia. or more 1.00 Each 35590.38

having three phase motor capacity not more than 7.5 H.P. with following

capacity (a) (12 stage) 280 to 240 LPM discharge at 90 to 104 mtrs. head

respectively suitable for 50mm dia. delivery pipe

133 Providing and erecting PVC corrugated flexible conduit with required numbers 125.00 Mtr. 26.26

of coupling, PVC bushes, Check nuts etc. complete of following sizes. (3)

mm diameter.

134 Lowering of submersible motor pump set complete with required. Nos. and 1.00 Job 2568.43

size of casing pipes erected by means of proper chain pulley block & pipe

wrenches after checking of threads of each pipe with coupling to take the

load of the pump set and pipe assembly filled up with water. (b) Above 60 Mtr

and up to 120 Mtr

135 Supplying and erecting approved make motor control cubical panel (Direct - 1.00 Each 8710.24

on - line) made from 16 G. CRCA sheet duly epoxy powder painted inside

and outside with hinged doors and locking, arrangement consisting of

suitable size of ON-OFF isolator (AC - 3/23 duty) main fuses, single phasing

preventer, indicating lamps for R-Y-B phases, overload relay, automatic water

incoming, wires duly socket crimped, main contactor & overload relay, start -

stop push buttons, to be erected on angle iron frame grouted on wall as

directed. The isolator, overload relay & contactors will be of L & T, Siemens

or BCH make only. (a) DOL upto 7.50 H.P.

136 Supplying and erecting XLPE (IS: 7098) (I)-88 ISI unarmoured copper cable 140.00 Mtr. 130.29

1.1 KV grade to be erected as directed of following size. (E) 3 core

137 Providing and supplying ISI mark CI D/F Butterfly Valves as per IS:13095 1.00 No. 1868.50

(Latest Edition) of following class and diameter including all taxes, insurance,

transportation, freight charges, octroi, inspection charges, loading, unloading,

conveyance to departmental stores, stacking etc. complete. (B) Butterfly

valves IS 13095 with ISI mark PN 1.6 (1) 50mm

138 Supplying & erecting carbon dioxide (CO2) fire extinguisher user of following 40.00 Each 8671.86

capacity with necessary clamps made from 50 x 6 mm M.S. Flat with nut &

bolts grouted in wall complete. [B] For 5.5 / 6.5 Kg. capacity.

139 Supplying & erecting ABC powder type 'Ceasefire' type Fire extinguisher as 40.00 Each 848.40

per IS 13849 or 1 Kg capacity with necessary clamp for erection on wall.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

Electrical Items

140 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm 422.00 Pt. 582.77

(Green) both are of ISI marked 1.1 kV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length, in below type of pipe erected with 6A

Modular type switch / bell push & accessories and earth continuity of

following type, erected on PVC / Metallic / Wooden box, single mounting base

frame covered with textured / metallic / white front plate modules erected on /

in wall / ceiling as per pipe erected, with necessary Lamp holder / ceiling rose

/ H.D. Connector as directed. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall / ceiling complete Cat. III

141 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both 81.00 Pt. 809.01

are of ISI marked 1.1 kV Grade FRLS PVC insulated multi strand copper

wires up to 10 mtr length, in below type of pipe erected with 6A Modular type

switch and hum free EME step type electronic fan regulator mounted and

accessories with earth continuity of following type erected on PVC / Metallic /

Wooden box, single mounting base frame covered with textured / metallic /

white front plate modules erected on / in wall / ceiling as per pipe erected.

with necessary ceiling rose / H.D. Connector as directed. (f) with medium

class Rigid PVC pipe and accessories erected concealed in wall / ceiling

complete Cat. III

142 Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both 54.00 Pt. 612.06

are of ISI marked 1.1 kV grade FRLS PVC insulated multi strand copper

wires up to 10 mtr length, in below type of pipe erected complete with

Modular type switch & 5 pin Plug erected on PVC / Metallic / Wooden box

covered with appropriate front plate modules erected on / in wall / ceiling as

per pipe erected with following type of accessories. [I] For 6A Plug and 6 a

switch with 2-1.5 sq.mm Cu. Wire from nearby switch board / mcb db board

(f) with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete Cat. III

143 Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin 122.00 Pt. 309.06

socket erected on PVC / Metallic / Wooden box, single mounting base frame

covered with textured / metallic/white front plate modules erected on / in wall /

ceiling with following type accessories Cat. III

144 Providing following type of Modular Type Accessories mounted with PVC / 140.00 Ea. 25.25

metallic / Wooden box, single mounting base frame covered with textured /

metallic / white front plate, modules erected with necessary connections as

per site situation directed by Engineer In charge. (7) Blank Plate Single Cat. III

(9) 16 Amp. SP one way switch Cat. III 6.00 Ea. 180.79

(10) 6/16Amp. Universal socket Cat. III 12.00 Ea. 199.98

(14) 6A/ 10A/ 16A/ 20A/ 25A/ 32A Double Pole Modular MCB Switch Cat. III 6.00 Ea. 410.06

145 Providing and erecting Mains with 1.1 kV grade FRLS PVC insulated ISI 2688.00 Mtr. 78.78

marked stranded Copper conductor wire in following type of pipe to be

erected concealed in /flushed on wall / ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for earth

continuity of following size (A) With medium class Rigid PVC pipe and

accessories (a) 2 wire 1.5 sq. mm

(b) 2 wire 2.5 sq. mm 1996.00 Mtr. 104.03

146 Providing and erecting Mains with 1.1 kV grade FRLS PVC insulated ISI 200.00 Mtr. 140.39

marked stranded Copper conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth continuity of following size

(A) with medium class Rigid PVC pipe and accessories (a) 2 wire 4 sq.mm

(h) 4 wire 6 sq.mm 230.00 Mtr. 326.23

(i) 4 wire 10 sq.mm (use earth wire of 4 sq.mm) 80.00 Mtr. 532.27

147 Providing and erecting Mains with ISI marked, 1.5kV grade electrolyte multi 42.00 Mtr. 47.47

stranded, annealed copper conductor with heat resistant PVC insulated

conforms to IS 694, IEC - 227 erected in existing pipe of following size

(Specifically for control panel, relays, power switchgears, motor starters &

control wiring) with required size of copper lugs, nuts and bolts if required.(d)

One wire 4.00 sq.mm

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

(e) One wire 6.00 sq. mm 44.00 Mtr. 70.70

(f) One wire 10.00 sq. mm 10.00 Mtr. 115.14

(i) One wire 35.00 sq. mm 1.00 Mtr. 376.73

(j) One wire 50.00 sq. mm 3.00 Mtr. 588.83

(l) One wire 95.00 sq. mm 4.00 Mtr. 1149.38

(m) One wire 120.00 sq. mm 2.00 Mtr. 1473.59

(n) One wire 150.00 sq. mm 2.00 Mtr. 1827.09

148 Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kV 340.00 Mtr. 58.58

grade ISI marked copper wires of following size to be erected as directed. (e)

1.50 Sq.mm 3 core round PVC sheathed

149 Decorative call bell Ting-tong box type 250 volts complete erected 2.00 Ea. 71.71

150 Providing and erecting decorative wall bracket fittings complete with LED 38.00 Ea. 1712.96

lamp and rust free fittings components mounted in chrome finish housing with

holder, clear / opaque glass diffuser complete erected with lead wires with

minimum 15 wattage capacity as per instruction engineer incharge / architect

/ authority. Cat-III

151 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 11.00 Ea. 373.70

0.5 Watt assembled on single MCPCB, with housing used as a heat sink shall

be made of thick sheet Steel conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion resistance with diffuser with

company mark/name 160V to 270V, Power Factor more than 0.95, THD <

15%, CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt, LED

LED driver efficiency > 85% (fitting required LM-79 & LM-80 Certificates)

(NOTE: Below description have shown ranges of Wattage capacity of LED

ranges shown) (A) Tube Light with integral driver (iv) 22-24 Watts, Surge -

2kV, IP-20, conventional 4 feet Cat. III

152 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 32.00 Ea. 427.23

0.5 Watt assembled on single MCPCB, with housing used as a heat sink shall

be made of thick sheet Steel conforming to IS: 513/CRCA/aluminium

pressure die cast powder coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with company mark/name 160V to

270V, Power Factor more than 0.95, THD < 15%, CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt, LED driver efficiency > 85% (fitting

required LM-79 & LM-80 Certificates) (NOTE: Below description have shown

any wattage capacity between the ranges shown) (A) Square/ Circular

shaped Surface / Recessed Mount Downlight with provision for spring loaded

mounting clips complete. IP20 (ii) 11-15 watts, Surge-2 KV Cat. III

(iv) 22-24 watts, Surge-2 kV Cat. III 112.00 Ea. 758.51

(B) LED Panel Light with provision for Plane front frame with translucent 172.00 Ea. 1794.77

cover fixed to housing complete. IP20 (vi) 36 watts, 24" x 24", Surge- 2kV

(H) Mirror Light 9 Watts, wall mounted minimum 1 feet long 2.00 Ea. 312.09

153 Supplying and erecting LED street light / Flood light fittings with High power 66.00 Ea. 4248.06

White LEDs wattage of 3 Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics / lenses, with toughened

glass with company mark/name engraved or embossed 160 to 270 V, Power

Factor more than 0.95, THD < 10%, CCT 3000 K to 5700K, Uniformity ratio

>0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85%.

(fittings required LM-79 & LM-80 certificates) (NOTE: Below description have

shown ranges of Wattage capacity of LED fittings. The Engineer incharge

(IP-65), Surge protection -4KV integral and light must have 440VAC line

supply with over-voltage protection. (ii) 48 - 59 Watts Cat. III

(B) Flood Light (IP-65), Surge protection -4kV integral and ,Light must have 12.00 Ea. 8201.20

440 VAC line supply with over-voltage protection. (vi) 160 - 199 watts Cat. III

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

(C) Post Top Lantern LED fitting comprises of finish cast aluminum spigot 2.00 Ea. 4096.56

and spun aluminum canopy fixed with opal polycarbonate, pipe arrangement

for vertical mounting driver and accessories wired up to terminal block. IP

(ii) 32-40W Cat. III

154 Providing and erecting Approved make Four pole moulded case circuit 6.00 Ea. 8861.74

breaker having breaking capacity ICU of 35 KA. at 415 V. having normal

current rating 125A. with Fixed thermal & magnetic release suitable to work

on A.C.supply 50 Hz. with all internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S. housing.ICS=100% of ICU only Cat III

155 Providing and erecting Approved make Four pole moulded case circuit 6.00 Ea. 17843.67

breaker having breaking capacity ICU of 35 KA. at 415 V. having Normal

current rating 200A.with variable Thermal & magnetic release suitable to work

on A.C.supply 50 Hz. with all internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S. housing ICS=100% of ICU only Cat III

156 Providing and erecting Approved make Four pole moulded case circuit 2.00 Ea. 23041.13

breaker having breaking capacity ICU of 35 KA. and above at 415 V having

normal current rating 250A. with variable thermal & magnetic release suitable

to work on A.C. supply 50 Hz. with all internal connections, spreader tinned

copper & complete erected in existing 16 G.M.S. housing. ICS=100% of ICU

only Cat III

157 Providing and erecting Approved make Four pole moulded case circuit 1.00 Ea. 27751.77

breaker having breaking capacity ICU of 50 KA and above at 415 V having

Normal current rating 400A. with variable Thermal & magnetic release

suitable to work on A.C. supply 50 Hz. With all internal connections, spreader

tinned copper & complete erected in existing 16 G.M.S. housing. ICS=100%

of ICU only Cat III

158 Providing and erecting Approved make Earth fault Relay suitable to mount 1.00 Ea. 5482.28

with inter connection suitable to following size of moulded case circuit breaker

having CT ratio & MCCB rating as following along with shunt trip 220V AC.

with all internal connections & complete erected in existing M.S. housing. (2)

125 A -200 A, CT Ratio 1/200

(3) 250 A -400 A, CT Ratio 1/400 1.00 Ea. 5956.98

159 Providing and erecting following additional parts for panel mounting MCCBs 14.00 Ea. 961.52

(A) Extended operating rotary handle with pad lock with three position trip, off,

on suitable for 25A to 250 A panel mounting Cat-III

(B) Extended operating rotary handle with pad lock with three position trip, off, 1.00 Ea. 1442.28

on suitable for 400A to 630 A panel mounting Cat-III

160 Supplying & erecting approved make Four Pole 415V change over switch 1.00 Ea. 22255.35

interior for panel mounting with operating mechanism A.C.23 duty confirming

to IS for (F) 400A Cat-lll

161 Supplying and erecting triple pole & neutral 440V / 500V panel mounting 1.10 Rn. 1961.42

Copper Busbars with four equal Nos. of electrolyte bus having current density Mtr.

not more than 1.6 Amp. / sq.mm (Rated current / cross section area) duly

wrapped with colour insulating tape for phase sequence of following current

carrying capacity, erected with necessary bus bar supports /insulators, main

cable socket to each bar, erected in existing cubical panel with necessary

connections.(A) Suitable for 100 Amp. Capacity.

(B) Suitable for 200 Amp. capacity 1.80 Rn. 3202.71

(C) Suitable for 300 Amp. capacity 0.50 Rn. 4909.61

(D) Suitable for 400 Amp. capacity 0.50 Rn. 7319.47

162 Providing and erecting Miniature circuit breaker single pole 0.5A to 2A system 68.00 Ea. 297.95

and having breaking capacity 10 KA to be erected in existing box confirming

to IS 8828/1996 with ISI Mark Cat III

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

163 Providing and erecting Miniature circuit breaker single pole 6A to 25A suitable 120.00 Ea. 123.22

to operate on 240 V A.C. system and having breaking capacity 10 KA to be

erected in existing box confirming to IS 8828/1996 with ISI Mark Cat III

164 Providing & erecting 240 V MCB double pole switch for motor & inductive 20.00 Ea. 329.26

load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in

existing box having following capacity (A) 6 to 32 Amp.Cat III

165 Providing & erecting 240 V MCB double pole switch for lighting Load (B 26.00 Ea. 306.03

Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box

having following capacity (A) 6 to 32 Amp.Cat III

(B) 40 Amp. Cat III 6.00 Ea. 325.22

166 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C 36.00 Ea. 655.49

Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box

having following capacity (a) 6 to 32 Amp. Cat III

(b) 40 Amp. Cat III 5.00 Ea. 736.29

(c) 63 Amp. Cat III 9.00 Ea. 811.03

167 Providing and erecting Sheet Steel powder coated MCB distribution board - 10.00 Ea. 2339.16

flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail,

Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs. (The DBs should be used of same company of

MCB to be used) suitable for (B) three phase incoming and single phase

horizontal type outgoing per phase isolation type (PPI) (b) sheet steel double

door (i) 4 way

168 Providing and erecting Approved make RCCBs conforming to IS: 12640 and 24.00 Ea. 2166.45

having sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240 V, 50 Hz. having characteristic of

quick action & tripping with all advance feature & do not incorporate any

electronic component for following Max. rating erected as directed (i)

Amps. DP Cat III

(ii) 40 Amps. DP Cat III 6.00 Ea. 2458.34

169 Providing and erecting Annealed bare Copper wire 4.064mm to 1.626mm. 9.00 Kg. 794.87

170 Providing and erecting Pipe type earthing having 150 cms.long and 2.5 cms. 43.00 Ea. 368.65

dia. galvanised iron pipe with coupling and buch buried in specially prepared

earth pit complete with necessary 8 SWG earth wire.

171 For using salt and charcoal / coke as required for pipe type earthing. 43.00 Ea. 171.70

172 Supplying & erecting earth pit of minimum bore dia.150mm size approved 9.00 Ea. 4591.46

make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of

50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-

250 Micron galvanising, connection terminal dia of 12mm with constant ohmic

value surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications with chamber and heavy

duty cover. (A) (approved make OEM has to submit test certificate including

value of earth resistance of installation duly stamped and signed by agency

and officer Incharge has to ensure the value of earthing resistane mentioned

in test Certificate) & having back filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017,

Voltage drop :- < 1 volt at no load & dry form, Sulphar content:- <2% (C) Back

fill Compound :- Earthing compound should be capable to retain moisture for

long time Necessary test report must be submitted by Agency.

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

173 Providing & erecting weather proof, dust & vermin proof, floor mounted front 8.00 Sq. 16323.62

operated outdoor type double door cubical panel board necessary IP-54 and Mtr.

above protection as per approval from engineer incharge made from

SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC

M.S.sheet for internal partitions with necessary accesories, supporting

angles/ flats channel including cutting, bending, drilling, welding, riveting with

internal partitions & cable alley as per requirements & instruction of engineer-

in-charge with erection of supplied switch gears, BUSBARS, suitable size of

inter connecting PVC copper wire / copper-aluminium strips, rubber

grommets, rib, bakelite control fuses / MCB for measuring instruments, earth

bus & earth bolts, foundation flange - bolts-base Plates, sufficient nos. of

hinged doors, handles with locking arrangement and rubber gasket, heavy

duty end terminal connection, danger notice board, necessary ventilation,

earthing strip complete.

174 Supplying & erecting FRLS-XLPE(IS:7098)(I)-88 ISI unarmoured copper 684.00 Mtr. 164.63

cable 1.1 kV grade to be erected as directed of following size. (B) 2 core

175 Providing and erecting FRLS-XLPE(IS:7098)(I)-88 ISI armoured cable 41.00 Mtr. 341.38

multistrand Aluminium conductor for 1.1 kV. to be laid on wall with necessary

clamps or in existing trench / pipe of following size of cables (C) 3 1/2 core

Sq.mm (25 Sq.1/2 mm core)

(E) 3 1/2 core 95 Sq. mm (50 Sq. mm 1/2 core) 47.00 Mtr. 589.84

(F) 3 1/2 core 120 Sq. mm (70 Sq. mm 1/2 core) 170.00 Mtr. 648.42

(H) 3 1/2 core 185 Sq. mm (95 Sq. mm 1/2 core) 185.00 Mtr. 1085.75

(I) 3 1/2 core 240 Sq. mm (120 Sq. mm 1/2 core) 10.00 Mtr. 1401.88

176 Providing and erecting FRLS-XLPE (IS:7098)(I)-88 ISI armoured cable 941.00 Mtr. 151.50

multistrand / Solid Aluminium conductor for 1.1 kV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of cables (B)

core 6 Sq.mm

(C) 4 core 10 Sq. mm 1436.00 Mtr. 168.67

177 Providing and erecting FRLS-XLPE (IS:7098)(I)-88 ISI armoured cable 217.00 Mtr. 184.83

multistrand Aluminium conductor for 1.1 kV. to be laid on wall with necessary

clamps or in existing trench / pipe of following size of cables (A) 4 core 16 Sq.

178 Making trench in soft soil of suitable width of 90 cm deep for laying cable or 1025.00 Mtr. 55.55

locating the fault all over the run and back filling the same and making the

surface as normal ground.

179 Providing & laying approved make Double walled corrugated pipes (DWC) of 1143.00 Mtr. 62.62

polyethylene (conforming to IS 14930 II) with necessary connecting

accessories of same material at required depth in existing trench for laying of

cable below ground / road surface for enclosing cable (A) 50 mm outer dia.

(B) 63mm outer dia. 155.00 Mtr. 73.73

(D) 120 mm outer dia. 155.00 Mtr. 137.36

180 Providing and fixing heavy duty flange type brass cable gland with rubber ring 92.00 Ea. 38.38

for PVC insulated armoured cable complete with out going tails, insulating

tape etc for following size of cables.(B) 2 to 4 core 6 Sq. mm

(C) 2 to 4 core 10 Sq. mm 48.00 Ea. 38.38

(D) 2 to 4 core 16 Sq. mm 4.00 Ea. 47.47

181 Providing and fixing heavy duty flange type brass double compression type 4.00 Ea. 75.75

cable gland with rubber ring for PVC insulated armoured cable complete with

out going tails, insulating tape etc for following size of cables. (B) 3 & 1/2

core 35/50 Sq. mm

(D) 3 & 1/2 core 95 Sq. mm 4.00 Ea. 131.30

(E) 3 & 1/2 core 120 Sq. mm 2.00 Ea. 140.39

(G) 3 & 1/2 core 185 Sq. mm 2.00 Ea. 238.36

(H) 3 & 1/2 core 240 Sq. mm 2.00 Ea. 247.45

182 Solder less crimping type Aluminium lugs conforming to IS suitable for cable 368.00 Ea. 6.06

of following size evenly crimped with high pressure tool & connected to

switchgear terminals with brass / cadmium plated nut bolts in an approved

manner. (A) 1.5 / 2.5 / 4 / 6 Sq.mm

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

183 Providing and fixing approved make Perforated C type cable tray. Made from 1119.00 Rmt 360.57

sheet steel. The cable tray should be single or double bended as per required

and as per IS 2062/1079 and shall be coated with hot dip galvanizing as per

IS 2629/4759 with max 17.5% perforation with coupler plate / Fish plate and

GI hardware like nut - bolt and washers etc. erection with necessary support

(included) as per specification and as per instruction of engineer in charge.

(2) 100 x 50 x 1.6 mm thick.

184 Providing and fixing approved make '90° Elbow' for Perforated C type cable 214.00 Ea. 116.15

tray. Made from sheet steel. The Junction should be bended as per IS

2062/1079 and shall be coated with hot dip galvanizing as per IS 2629/4759

with coupler plate / Fish plate and GI hardware like nut - bolt and washers

etc. erected on existing support as per specification and as per instruction of

engineer in charge. (2) 100 x 50 x 1.6 mm thick.

185 Providing and erecting Approved make Ceiling fan with double ball bearing 25.00 Ea. 1596.81

ISI mark with condenser A.C. 230V.50 Hz.1200 mm. sweep complete,

canopy erected on existing hook or clamp with earthing. [Make shall be

approved by Engineer in charge]

186 Providing & erecting Approved make Ceiling Fan with double ball bearing ISI 56.00 Ea. 1738.21

mark with condenser A.C.230V 50 Hz. 1400 mm. sweep complete, canopy

erected on existing hook or clamp with earthing [Make shall be approved by

Engineer cin charge]

187 Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe 137.00 Mtr. 108.07

down rod erected duly painted for fan complete with proper insulation without

leakage and earthing.

188 Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the 127.00 Ea. 108.07

RCC bars up to 50mm length each side and pierced through a 16 Gauge

M.S. box / Heavy Duty PVC box complete erected concealed in Ceiling with

necessary finishing.

189 Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan 127.00 Ea. 18.18

190 Supplying & erecting approved make low noise decorative exhaust fan having 16.00 Ea. 1366.53

square frame ABS body with inbuilt lowers & square frame.200mm with

1350RPM Cat.II

191 Supplying and erecting approved make oscillating type bracket fan A.C. 37.00 Ea. 2534.09

230V. 50 Hz 400/450 mm sweep wall mounted with height adjustment and

rotary tilting device complete with guard, flexible Core plug top complete

erected with lead wires as directed. Cat.II

192 Supplying and erecting approved make Octagonal pole made from HR sheet 43.00 Ea. 7561.87

steel. The pole should be made as per IS and shall be coated with hot dip

galvanizing as per IS 2629/2633/4759, suitable suspend local wind speed

with integral Junction box consist of terminal plate of min 6mm Hylam sheet,

standard profile 35mm x 7.5mm Din-Rail for MCB Mounting, stud type

terminal and arrangement for cable termination to be erected with suitable

foundation (Included) as per details given by manufacturer considering site

requirement. (C) 5 Mtr. Long 70 mm top x 130 mm bottom dia, 3 mm

thickness with 200mm x 200mm x 12mm base plate, 4-M16 Bolts and 600mm

long with necessary G.I. J Bolts. Approx Pole weight 46 kg

193 Supplying & erecting approved make SMC press moulded composite FRP 2.00 Ea. 476.72

loop-in, loop-out approx. 2mm thick box complete with Bakelite connector

strip 5way (3P+N+E), DIN rail for mounting mob & hinged doors as per

requirement having locking arrangements with mounting clamp with nuts,

bolts & washers suitable for erection on pole with cable clamps & earth bolt of

following size of box. (C) 150mm x 125mm x 100mm [deep]

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

194 Supplying and erecting Street light pole bracket comprising main B Class GI 20.00 Ea. 491.87

pipe of 4.2 cm/require outside dia. complete with suitable B Class G.I. sleeve

tubing of approx. 45cms.length and suitable for 76.5mm / 80mm / require size

of pole top having nuts and bolts for fixing the brackets and having spread of

0.5 mtr. Length with 110 deg.with vertical plane and suitable welded stiffener

reducer and nipple with check nut complete painted with one coat of Red

oxide / PU base primer and two coats of Aluminium / PU paint. paint with

following nos of arms. [A] Single Arm bracket 0.5 Mtr

[B] Double Arm Bracket 0.5 Mtr 23.00 Ea. 622.16

195 Supplying & erecting IP 55 grade following size section pillar fabricated from 2.00 Ea. 3595.60

joint less M.S. Sheet with angle iron legs made from jointless M.S. Angle with

cable clamps to be buried in ground to have appropriate erection to work

uniform until erected with cement concrete foundation and 45 cm high bricks

work finishing with plaster etc. hinged double door internally supported on

both side, with internal and outside looking arrangement with lock and keys in

duplicate 35 x 35 x 5 mm M.S. Angle of Two Nos. one is welded and other

with nut and bolt for erecting Bakelite sheet. Painting the Section Pillar inside

and out side with three tank powder coated paint. section pillar roof should be

without joint with water leakage proof & tested as per IP 55 test & followed by

IS 2147 of 1962 (B) 75 x 60 x 45 cm section pillar fabricated from 16 Gauge

MS Sheet with angle iron legs 45 cm long made from 35 x 35 x 5 mm thick

196 Supplying and erecting HYLAM sheet on existing angle iron frame for 1.00 Sq. 1156.45

following thickness (C) 6mm Mtr.

197 Supplying & erecting approved make Digital time switch having lithium cell 6 2.00 Ea. 3168.37

years operative and operate battery backup 1 channel day clock with

memory programme, suitable to operate on 240V + 5%, 16A with, floating

contacts Minimum switching setup time 1 minimum & LCD display. Also

comprised permanent ON/OFF switching. Programming switches & housed in

fire proof thermoplastic enclosure & transparent cover erected as required

with necessary connection erected as directed.

198 Supplying & erecting power contactor ,AC3 duty for time switch complete 2.00 Ea. 2782.55

erected as per direction Cat III (D) 4 pole 440V 40 Amp.

199 Supplying, erecting, testing, commissioning approved make M.S. Polygonal 2.00 Ea. 162858.46

High Mast Pole having following general Specification.

(a) Polygonal Section fabricated from M.S. Plate confirms BSEN 10025 & Hot

deep galvanized minimum 65/86 micron (as per IS 2629 /1985) Lantern

carriage with ring and rubber lines for erection of luminaries of suitable site.

(b) Maximum telescopic section not more than four

(c) Double drum gear pipe motorized winch with 6mm dia S.S. Rod (For

mtr and above size)

(d) Approved make L.E.D. aviation light = 1 No. Lightening arrestor = 1 No.

with necessary wiring of 2.5 sq.mm 5 core ISI copper cable Unarmoured.

(e) Bottom most section suitable for mounting reversible motor and

switchgears having door not more than 1400mm x 300mm with waterproof

gasket & hinges & locking arrangement.

200 Providing and erecting Inverter based approved make split air-conditioning 2.00 Ea. 70142.48

unit consisting of condensing unit with variable speed fan motor, inverter type

hermetically sealed rotary compressor with accessories etc. duly connected

separately erected evaporating unit and blower motor with its accessories by

means of extra supplied proper insulated copper tubing,drain PVC pipes

suitable for (cost includes Eco Friendly green gas charging and 15A plug top

& Remote Control & MS Stand) with necessary core cutting. (2) For ISEER

Range (KWH/KWH) (4.0 to 4.49) (C) for 1.7 to 2 ton capacity

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

201 Providing and erecting Inverter based approved make Cassette type split air- 24.00 Ea. 177336.81

conditioning unit consisting of condensing unit with fan motor, hermetically

sealed scroll/rotary compressor with accessories etc. duly connected

separately erected evaporating unit and blower motor with its accessories by

Eco friendly Green gas charging & Internal copper wiring & Remote control (3

star and above of current year) with necessary core cutting. (D) for 4 ton

capacity- 1/3 Phase.

202 Supplying and erecting insulated pair of soft copper tubing open or concealed 694.00 Rmt. 1158.47

including power and control cable, necessary PVC drain pipes for Split /

Cassette AC machine up to 4 TR capacity

203 Providing & erecting water cooler having storage capacity 150 Ltr. & cooling 2.00 Ea. 61482.74

capacity 150 Ltr.per hour @ an ambient temp of 45˚ C. The outlet temp. of

the water should drop by 15˚C within a hour, The water cooler should be

comprising of hermetically sealed compressor, fan motor, condensing unit,

water tank surrounded by evaporating, coil, thermostats, relay etc.complete

with necessary inlet & outlet connection. The body of water cooler will be

made from Stainless Steel and ISI Certified.

204 Supplying & erecting 5 stage single reverse osmosis water purification 2.00 Ea. 29187.99

system with M.S. powder coated frame, prefilter housing with 'O' ring

presediment filter GAC filter, carbon filter suitable buster DC pump capacity

80 psi, mention with 40 psi inline type post carbon filter auto low & high

pressure switches with following size of storage tank & LPH capacity &

erected as directed [C] 50 Ltr / Hr with 150 psi 2 nos booster pump.

205 Supplying and erecting approved make panel mounting type Digital Voltmeter 7.00 Ea. 1275.63

having 3 digits LED display, 0 to 750 AC Volts range erected on existing

panel board with all connection, wiring etc. with manufacturers calibration

certificate.

206 Supplying and erecting approved make panel mounting type Digital Ammeter 7.00 Ea. 1558.43

having 3 digits LED display, external CT operated, calibrated for 0 to

Amps suitable to operate on 500 Volt AC, erected on existing panel board

with all connection, wiring etc. with manufacturers calibration certificate.

Supply 500 V on existing panel board with necessary connections.

208 Providing & erecting L.T. Current Transformer with bar primary 50/5 to 1000/5 21.00 Ea. 274.72

ratio 15 VA burden erected in existing CRCA box duly secured with insulating

materials connected to the meter

209 Supplying and erecting approved make suitable panel indicator LED type 21.00 Ea. 43.43

lamp, lens cover, complete erected with necessary connections.

210 Providing & erecting open well horizontal mono block pump set with cast iron 2.00 Ea. 17279.08

body, complete for three phase submersible motor having [C] For 3 HP

phase open well horizontal mono block pump set suitable for 85 LPM to

LPM @ 11 mtr to 33 mtr head suitable for 50/65 mm dia delivery pipe.

211 Supplying & erecting approved make motor control cubical panel (Direct - on 3.00 Ea. 7722.46

- line) made from 16 G. CRCA sheet duly epoxy powder painted inside and

outside with hinged doors and locking, arrangement consisting of suitable

size of ON- OFF isolator (AC - 3/23duty) main fuses, single phasing

preventer, indicating lamps for R- Y - B phases, overload relay, Automatic

incoming, wires duly socket crimped, main contactor & overload relay, start -

stop push buttons, to be erected on angle iron frame grouted on wall as

directed. The isolator, overload relay & contactors will be of L & T, Siemens

or BCH make only. (A) DOL up to 5.0 H.P.

212 S.I.T.C. submersible pump set suitable for bore of 100 mm. dia. or more 1.00 Ea. 22992.65

having three phase motor capacity not more than 3 H.P. of different range

with following capacity. Lifting and Lowering taken extra. (A) (20 stage) 170 to

185 LPM discharge at 57 to 48 mtrs. respectively head suitable for 50 mm

dia. delivery pipe Cat.III

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

213 Lowering of submersible motor pump set at the depth of following, complete 1.00 Per 1711.95

with required. Nos. and size of casing pipes erected by means of proper Job

chain pulley block & pipe wrenches after checking of threads of each pipe

with coupling to take the load of the pump set and pipe assembly filled up

with water (A) Up to 60 mtrs.

(D) For Open well Horizontal submersible pump set for sump well (i) 1 HP to 2.00 Per 856.48

214 Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible 20.00 Mtr. 104.03

Submersible copper cable approved make of following Size. (B) 3 Core x

(C) 3 Core x 4 Sq. mm 100.00 Mtr. 146.45

215 Supplying of following size of STANDARD UPVC column pipe with coupler 10.00 Mtr. 297.95

and wire lock [D] 50 mm dia

216 Supply of following size of TOP & BOTTOM accessories i.e. Adaptor set (CI) 1.00 Per 1489.75

long, pump guard set, starter pipe Rubber ring for submersible pump & UPVC Set

column pipe as directed by Engineer - in - charge with necessary plumbing as

desired.[D] 50 mm dia

217 Providing & laying approved make ISI marked HDPE 6Kg / cm2 (Class-3) as 60.00 Mtr. 163.62

per IS:4984:1995 PE-80 to be erected at road crossing on or floor as directed

for laying of cable. The pipes as following size of dia & weight per 6 mtr. (B)

50 mm inner dia.

Total Rs.

i.e. Rs. Eleven Crore Thirty Nine lacs Ninety Eight thousand Two hundred Nineteen and Seventy Eight paisa only.

I/We am/are willing to carry out the work @ ______________ % above/below percent (Should be written

in figures and words) of the estimated rate mentioned above. Amount of my /our tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

Net Rs. ___________________________ Total Rs. ________________________

In words ____________________ In words ____________________

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-

Charge for which no extra payment shall be made.

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills.

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C, Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is a

change as per actual mix design the cost of difference of cement consumption have been deducted from the rate of

original item at the rate of input rate mentioned in all the tender.

5. The Contractor will have to submit the all required mix design at his own cost before execution as directed

and to be approved from the Engineer in charge.

Above all items of "Schedule-B" with Item Description, Unit, Rate & Amount have verified by me and found order.

Deputy Executive Engineer Sr. Divisional Account Officer Executive Engineer

Lunawada (R & B) Sub Division, Mahisagar (R & B) Division, Mahisagar (R & B) Division,

Lunawada Lunawada Lunawada