SPL REPAIR TO BLDG NO PB-41 CENTRAL MI ROOM AND PB-41A GARRAGE AT MIL STN KANCHRAPARA UNDER GE BARRACKPORE

M&L for Cleaning vertical and horizontal surfaces of unplastered masonry wall and concrete surfaces for loose materials/dust and applying two coats of epoxy resin component (Dr. Fixit DAMPGUARD or equivalent) solution/mix using nylon brush pouring Base part in appropriate container followed by the Hardner part and mix thoroughly to attain homogeneous smooth paste and dilute the mixed compound with water in ratio 1 part Base: 1 part Hardner: 1 part water by slow addition and mix thoroughly until a brushable consistency is obtained, first coat will be allowed to dry for 6 to 8 hrs before application of second/final coat) including curing treated surface for 24 hrs complete all as specified and as directed.

Dismantling of asbestos cement sheet (corrugated or semi corrugated etc) as in roof covering complete all as specified and as directed.

Dismantling of plain or corrugated steel sheeting, any gauge or any thickness as in roof covering, wall cladding etc., complete all as specified and as directed.

M&L Pre- painted hot dip aluminium Zinc alloy metalic coated trapezoidal profile steel sheet 0.50mm thick ( Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in roof covering/wall cladding, fixed with self tapping screws complete all as specified and as directed.

M&L Pre- painted hot dip aluminium Zinc alloy metalic coated plain steel sheet 0.50mm thick ( Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in roof covering/wall cladding, fixed with self tapping screws as specified complete all as specified and as directed. Note: To be executed for provision of ridges and hips.

M&L for powder coated anodised aluminium snap grid frame work for false ceiling, Size of grid 605 x 605mm using Main/Cross Bulbed tees - Tapered head (Web : 25mm Flange : 38mm) of weight not less than 0.249 kg/m and Equal angle of size 25mm of weight not less than 0.196 kg/m, including hangers 6 mm dia GI (n.exc 1200 mm in length apart) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia 40 mm long and fixed or laid 4mm thick non asbestos fibre cement building boards (E-board) with screws including dismantling of old ceiling board of any description complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and as directed.

M&L Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 410 -W (GdeE- 250) quality A complete all as specified and as directed.

M&L for rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1998 grade St.-240 complete all as specified and as directed.

S&F rolled mild steel plates (plain or chequered) square cut or notched (ordinary & counter sunk) forming holes, with riveted, bolted or welded attachment GDE Fe410-W (GdeE- 250) quality 'A' complete all as specified and as directed.

S&F for Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe 290, Gde-E-165 completed all as specified and directed.

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc similar work conforming to Fe-290 GdeE-165 complet all as specified and as directed.

S&F Steel rolling shutters, with ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete gear operated type with bevel gear box and crank handle including Safety lever locks mild steel with 4 levers for rolling shutters complet all as specified and as directed.

M&L for preparation of new steel surface over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide Zinc chrome primer complete all as specified and as directed.

M&L for complete removal of old painted steel surfaces by paint removers or burning off by blow lamps, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide Zinc chrome primer complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as directed.

M&L for hard core with broken stone or boulder of gauge not exc 63 mm, deposited , spread and levelled in layers n. exc 15 cm thick, watered and rammed to a true surfaces complete all as specified and as directed.

M&L for 100 mm thick PCC 1:5:10 type E-2 (using 40mm graded crushed stone aggregate) as in sub base complete all as specified and directed.

M&L for PCC 1:3:6 Type C-2 ( Using 40mm graded crushed stone aggregate) as in foundation , filling, and mass concrete complete all as specified and directed.

M&L for PCC 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) as in surface channel or drain including necessary form work and extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred /stopped ends etc. complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6, type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed.

M&L for 75 mm thick PCC 1:2:4 type B-2 (using 40mm graded crushed stone aggregate) as in sub base complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4, type B1 (using 20mm graded crushed stone aggregate) as in floor complete all as specified and as directed.

S&F 38mm Plastic dividing strips, 1.5mm thick and inserted in position to conform to design complete all as specified and as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L for RCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in Slabs supported on walls, beams, and column in floors, roof, landing, balconies, canopies, deck slab and in shelves and like etc. complete all as specified and as directed.

M&L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape as required including cranking, bending spirally for hooping for columns,hooking ends and binding with mild steel wire(annealed) not less than 0.9mm dia as in reinforcement bar complete all as specified and as directed.

M&L for mild steel TMT bars 8 mm dia cut to length, bent to shape as required including cranking, bending spirally for hooping for columns,hooking ends and binding with mild steel wire(annealed) not less than 0.9mm dia as in reinforcement bar complete all as specified and as directed.

Use and waste formwork to sides and soffits of floor or roof beams, beams haunchings, girders, bressumers, lintels over 1.5m clear span, cantilevers, shelves including supports overhangs etc also splays between floors and beams for flat Rough finished surfaces of concrete complete all as specified and as directed.

Demolition of brick or stone masonry work built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed.

M&L for brick work with sub class ‘B’ bricks (locally available best quality) straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work with subclass ‘B’ bricks, (locally available best quality) straight or curved on plan to any radius in half brick thick wall, built in cement mortar (1:4) complete all as specified and directed.

Taking down cement plaster on walls, chajja surfaces, etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for rendering 10 mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 15mm thick rendering in cement mortar (1:4), in two layers, under coat of 10 mm thick & top of 5 mm thick, to other than fair faces of brick or concrete wall surfaces, top layer 5 mm thick mixed with water proofing compound @ 200Ml per bag(50Kg) of cement or as per manufacture's instructions, finished even and smooth without using extra cement complete all as specified and as directed. Note : Water proofing compound will be measured and paid separately as "Supply only".

M&L for rendering 5 mm thick in cement mortar (1:3) as in ceiling surface finished even and smooth without using extra cement complete all as specified and as directed.

Supply only liquid water proofing compound complete all as specified and as directed.

Complete removal of existing treatment & levelling of wall/ceiling surface using MECHANICAL / ELECTRICAL OPERATED SANDING / SCRAPING MACHINE WITH INBUILT VACCUM SUCTION system to suck the existing treatment as retrieved by scrapping/sanding etc for obtaining smooth paintable surface complete all as specified and directed.

M&L for applying 3mm thick wall care putty on wall surfaces complete all as specifed and as directed.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces using Airless Paint Primer Sprayer using smart technique, on Old prepared surfaces /newly plastered surface of wall, cornices complete all as specified and as directed .

M&L for preparation of newly plastered surface of walls and applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed.

M&L for complete removal of existing treatment surfaces of wall and applying three coats of white wash complete all as specified and as directed.

M&L for complete removal of existing treatment surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing complete all as specified and directed.

M&L for coloured joint free non-skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, laid in floors etc. over and including 15 mm thick screed bed in cement motar 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles, complete all as specified and as directed.

M&L for coloured joint free non skid ceramic tiles 7 to 8mm thick (square / rectangular )area of each tiles exc 0.18 sqm but not exceeding 0.38 Sqm on vertical surfaces as skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match with coloured tiles over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

M&L for glazed light coloured/printed ceramic tiles 350x250x7mm/450x350x7mm thick in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry pointed in white or coloured cement to match colour of tiles, over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

Demolition of stone slab and tiles of any description or thickness in floor, apron etc laid, bedded and pointed in cement mortar complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 20 to 25 mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab laid over and including 15 mm thick screed in cement mortar (1:6) including rubbing and polishing complete all as specified and as directed.

M&L for Machine cut Kota stone slab 20-25 mm thick in verticle surface such as riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab over 10 mm thick rendering in CM (1:4) including rubbing and polishing complete all as specified and as directed.

M&L for 16-18mm thick Mirror polished, high gloss finish Granite ((absolute Jet/telephonic Black) work in steps, jambs & soffits of chowkhat (including necessary pasting), pillars, window-cills, basin platforms, urinal partitions and like overb 15 mm thick screed bed in cement mortar 1:4, pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including necessary cutting for sunk basin/sink, making holes for fixing hinges, door bolts etc complete all as specified and as directed.

Providing edge moulding to 16-20mm thick granite stone slab including machine polishing to edge to give high gloss finish etc. complete all as specified and as directed.

M&L for lacquer coated, polished chequered cement concrete tiles in floor, area exc 0.06 Sqm but not exc 0.11 Sqm, 30 mm thick with white cement and pigments of approved make jointed with cement slurry and pointed with white cement mixed with colour pigment to match with the tiles over and including screed bed of 15 mm thick cement mortar (1:6) complete all as specified and as directed.

S&F 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand including dismantling of old paver block complete all as specified and as directed.

Taking down chowkats or frame with shutters (without taking off shutters from frame) each not exceeding 1.50 Sqm complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutters from frame) complete all as specified and directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 100mm x 55mm size Mild steel black door frame, thickness 2.2mm, weight not less than 5.1 kg/m, made out of YST-210 grade complete all as specified and as directed.

S&F 35mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides completes including vision panels, square or rectangular, 02 glass sheets shall be fixed back to back with 20-25mm wooden bead separation including lipping complete all as specified and as directed. NOTE : Glass sheet shall be measured and paid separately

M&L for preparation of new wood or wood based surface of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paints over a coat of pink primer complete all as specified and as directed.

S&F 100 mm size stainless steel butt hinges heavy weight complete all as specified and as directed.

S&F 100 mm size aluminium alloy with galvanized mild steel hinge pin, anodised and fixed, type C-21 butt hinges, complete all as specified and as directed.

S&F 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 125mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150mm size aluminium handles, cast type, anodised complete all as specified and as directed.

S&F 100mm size aluminium handles, cast type, anodised complete all as specified and as directed.

S&F 250 mm long aluminum alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of steel, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy complete all as specified and as directed.

S&F floor door stopper of aluminium alloy body and tongue, overall length of cover plate 140 mm anodised with hard drawn steel spring, fixed in floors complete all as specified and as directed.

S&F in repairs, aluminium door closer (diecast) body hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and complete all as specified and as directed.

S&F in repairs 25mm dia heavy duty stainless steel curtain rod (SS-304), cut in required length and size to fit with opening incl fixing in bracket with necessary screws fitted on bracket and decorative nobs on sides with necessary arrangement complete all as specified and as directed.

S&F 125mm long curtain rod side brackets of stainless steel (SS 202), angular or cantilever type fixed to wall with 02 nos screws on each bracket and fitted screws for fixing curtain rod including stainless steel (SS 202) decorative design plain metal colour nobs (oval/sphere shape) with fixing arrangement complete all as approved and shown by Engr-in-charge.

S&F 18/19mm thick solid PVC composite sheet, prelaminated on front side and plain matching dark shade laminated background as in kitchen cabinet shutters, backing, sides, top/bottom, etc, fixed with SS flush screws, necessary cutting for required shape, rebate, hinges, hooks, etc., fixing with self closing hinges, wall hanging hooks, magnetic locks, handles, etc including dismantling of old decay boarding of any description complete all as specified and as directed. Note :- Necessary Hinges, hooks, handles and locks shall be measured and paid separately as supply only.

Supply only heavy duty Slim Nickel plated Stainless steel magnetic catch with strong magnet of size 11mm x 35mm x 4mm complete all as specified and as directed.

Supply only heavy duty stainless steel slip on hinges, self closing type with opening full overlay or 105°, suitable for 25mm thick shutter of maximum size 850mm x 550mm complete all as specified and as directed.

Supply only Ergonomically designed powder coated Aluminium anodised handle, suitable for 25mm thick shutter, size 10-15mm x 200mm complete all as specified and as directed.

S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frames for door, windows, ventilators, partitions etc. with one or more rebates including joining cleat for fixing etc complete all as specified and as directed.

S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium door shutters, aluminium section weighing not less than 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified and as directed.

S&F Power G Sliding roller for aluminium sliding doors complete all as specified and as directed.

S&F powder coated (Brown/ivory as directed) anodised aluminium alloy sections 3 tier track sliding windows Series B (Jindal aluminium window section catalogue) weight of section frame 1.248 kg/m and shutter section weight 0.547 kg/m duly fitted with neoprene beading, glazing clips, tinted glass panes 4.80/5.0 mm nominal thickness, aluminium expanded mosquito proof wire cloth 0.45 mm thick and average width of aperture 1.4 mm, aluminium alloy handles etc complete all as specified and as directed.

S&F powder coated (Brown/ivory as directed) anodised aluminium ventilator with fixed aluminium frame of size 65 x 40 x 1.98 mm thick or equivalent section fixed in vertical position with aluminium vertical members and half portion to be provided with 4 mm thick pinhead frosted glass and remaining portion to be louvered using 4 mm thick pinhead frosted glass and outer side louvered portion covered with aluminium expanded mosquito proof wire cloth 0.45 mm dia and average width of aperture 1.4 mm with necessary frame work, rubber gasket and aluminium beading complete all as specified and as directed. NOTE : Glass sheet shall be measured and paid separately as supply only.

Supply only 4mm thick Figured glass, pinhead type in squares n exc 0.5 sq. m each pane complete all as specified and as directed.

S&F 5.5mm thick frosted glass, ordinary quality and glazing with rubber beading in square exceeding 0.50sqm in each pane complete all as specified and as directed.

S&F 12mm thick Toughened glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes as required including dismantling of old aluminium door complete all as specified and as directed.

S&F Aluminium extruded BM (Black metal) finish outliner/perimeter edge profile, 12.5 x 14.8mm, fixed with double sided tape, suitable for 12mm toughened glass door complete all as specified and as directed. Note : Quoted rates shall be including cost of double sided tape and all other fixing accessories as required.

Supply and fix Aluminium extruded BM (Black metal) finish outliner hinged profile, 12.5 x 14.8mm, fixed with double sided tape, suitable for 12mm toughened glass door complete all as specified and as directed. Note : Quoted rates shall be including cost of double sided tape and all other fixing accessories as required

S&F EPDM gasket for outliner hinge profile, black, for minimize the gap between wall and glass door profile complete all as specified and as directed.

S&F Black metal finish Aluminium alloy Top patch with variable pivot point of 55/65mm including SS-304 cover secured with small 'L' key complete all as specified and as directed. (Make : Ozone OPF-2 STD BM or equivalent)

S&F Black metal finish Aluminium alloy Top pivot with 15mm dia wear resistant SS-304 pivot pin held in overhead structure complete all as specified and as directed. (Make : Ozone OFS-ACC-GDP STD BM or equivalent)

S&F Black metal finish Aluminium alloy Bottom patch with variable pivot point of 55/65mm including quick release cover secured with small 'L' key complete all as specified and as directed. (Make: Ozone OPF-3 STD BM or equivalent)

S&F Black metal finish Aluminium alloy corner patch lock with euro profile cylinder and strike plate, dead bolt projection of 15mm (single throw), three high security computer keys, 1.5mm SS-316 cover plate secured with small 'L' key and snap-fit mechanism complete. (Make: Ozone OPL-1 STD BM or equivalent)

S&F Aluminium extruded BM (Black metal) finish sleek glass door handles, 25mm dia, 450mm long, with gaskets, suitable for 12mm toughened glass door complete all as specified and as directed. (Make: OZONE OGH-11 25x450mm BM or equivalent)

M&L for Hydraulic operated Floor door spring, size 256 x 105 x 50mm with adjustable latching and closing speed, mechanical hold open 90 degrees, made out of high grade CI body housed in GI steel box with high corrosion resistant SS-304 cover plate, thermostable hydraulic fluid filled to ensure smooth operation in any climate, complete. (Make: Godrej or equivalent)

S&F 500 litres capacity rotational moulded polye-thylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I with and including 20mm bore dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed etc including dismantling of old tank of any description complete all as specified and as directed.

S&F in repairs, stop valves, 20mm dia, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.

M&L for Cutting chases, pinning in, making good to facing where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunsheds, shelves, lintel etc and cutting chases for concealed water tubing or concealed conduit wiring etc n. exc. 10 cm width or girth complete all as specified and as directed.

Supply & Laying CPVC pipes SDR 11 and plain CPVC SDR-11 fittings on walls/ceiling or laying in floors/concealed in wall of size 20 mm outer dia including taking up or down 15mm dia steel tubing complete all as specified and as directed.

Supply & Laying CPVC pipes SDR 11 and plain CPVC SDR-11 fittings on walls/ceiling or laying in floors/concealed in wall of size 25 mm outer dia including taking up or down 20mm dia steel tubing complete all as specified and as directed.

Supply & Laying CPVC pipes SDR 11 and plain CPVC SDR-11 fittings on walls/ceiling or laying in floors/Trenches of size 50 mm outer dia including taking up or down 50mm dia steel tubing complete all as specified and as directed. Note :- For Item No 98 & 100, the cost of Brass threaded / plain fittings such as Brass Elbow, Brass Tee, Union, Tank Adaptor, reducers & other accessories wherever required is deemed to be included in the unit rate.

S&F in repairs, bib taps 15mm dia cast copper alloy chromium plated, fancy type with crutch or butter fly handles with and wall Flange, screwed down for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs, stop valves/ angular stop valve, 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directe.

S&F in repairs, 2 way angle valve (concealed type), 15mm dia cast copper alloy chromium plated, fancy type with crutch or butterfly handles screwed down for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repairs, glossy finish chromium plated ABS body shower rose, 175-180mm dia including brass chromium plated 375mm long arm with flange, screwed down for iron pipe or for brass ferrule complete all as specified and directed. Make : Prayag Cat No. BS-78 or equivalent in Jaquar / ESSCO/Hindware

S&F in repair, tubular towel Rail of 20mm dia and 60cm in length, D shaped, with brass chromium plated brackets complete all as specified and as directed.

S&F in repairs, towel ring brass chromium plated complete all as specified and as directed. Make : Prayag, Cat No BA-41 or equivalent in Jaquar / Hindware/parryware

S&F in repairs, Brass Soap Dish fixing to walls with screws complete all as specified and ad directed. Make : Prayag, Cat No BA-45 or equivalent in Jaquar / Hindware/parryware

S&F in repairs, Glass shelf of size 500 mm x125 mm with chromium plated guard complete all as specified and as directed. Make : Prayag, Cat No BEA-45 or equivalent in Jaquar / ESSCO/Hindware/Parryware

S&F in repairs, 32mm bore Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed.

S&F in repairs, Health faucet (ABS Body) mild steel chromium plated suitable for 20mm outer dia CPVC pipe with 1.25m long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F 1.5mm thick glossy stainless steel laboratory sinks, overall size 585mm x 485mm bowl size 535mm x 432mm x 200mm including 40 mm waste coupling brass chromium plated suitable for Sink, with long screwed shanks and fly nuts and pipe, cast iron cantilever brackets and connecting union to pipe complete. Make : Nirali Glister sinks or equivalent in Blue star/Prayag

S&F in repairs, Brass CP Sink Mixer with movable neck, fixed to wall, for mixing hot & Cold water screwed down for iron pipe and fixed and joint with adhesive, Teflon tape, etc complete including taking down old CP Pillar tap complete all as specified and as directed. Make : Prayag, Cat No 7255 or equivalent in Jaquar / ESSCO/Hindware/Parryware

S&F in repairs, vitreous china wash hand basin, white flat back size 550 mm x 400 mm including brackets and Self-closing pillar tap, 15 mm bore chromium plated, cast copper alloy with capstan heads, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts and PVC waste pipe,15mm dia 600mm long PVC connection pipe complete all as specified and as directed.

S&F in repairs, Vitreous china urinal, half stall white (excluding flushing cistern) including urinal spreader, 450mm long PVC connection pipe , 32mm PVC waste pipe & 32mm waste coupling providing and fixing plugs, bedding urinal against wall in mortar 1:2, securing urinal to plug, with and including 60mm long screws, pointing around urinal back in cement, fixing flush pipe, grating and union for discharge pipe complete all as specified and as directed.

S&F in repairs, vitreous china wash down water closet (padestal pattern) including connection to drain (or outgoing pipe) and flushing pipe, anti syphonage pipe, trap set and including white or black seat cover for padestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws etc complete all as specified and as directed.

S&F in repairs, 10 Litres capacity PVC valveless syphonic action type, flushing cistern, low level, white or coloured, with inlet, ball valve, float and handle including brackets,PVC connection pipe 15mm dia, 600mm long etc complete all as specified and as directed.

M&L for Preparing of spalled RCC surfaces due to seepage (n-exc 50mm deep) by exposing fully corroded steel in the repair area and remove all scales and corrosion deposits mechanically or ideally by grit blasting, clean the surfaces and remove loose concrete, any dust, oil paint, grease etc and pre-wet the surface with water and allow to dry slightly, apply approved zinc primer over the cleaned re-bars & allow to dry before repair and the substrate should be primed by applying one neat/clear coat of approved Epoxy bonding agent, finally apply Polymer Mortar of approved Make prepared as per manufacturer instructions (laid in 10 to 15mm thickness with bonding agent accompanied after each 15mm layer) to the prepared substrate by hand when primer becomes tacky ensuring that the material reached evenly behind bars including curing the surfaces complete all as specified and as directed.

S&F in repairs, 110 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints and laid in trenches or in floor complete all as specified and as directed. Note : Excavtion & Earth work shall be deemed to be included in the quoted rate.

S&F in repair 110 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S&F in repairs, 75 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints and laid in trenches or in floor complete all as specified and as directed. Note : Excavtion & Earth work shall be deemed to be included in the quoted rate.

S&F 110 mm dia PVC (SWR) bends of any radius complete all as specified and as directed.

S&F 75 mm dia PVC (SWR) reducer complete all as specified and as directed.

S&F 110mm dia PVC (SWR) junction single, (single T) equal or unequal provided with access door complete all as specifiec and as directed.

S&F 180mm x 100mm size Salt-glazed stoneware gully traps, square or round mouthed, tvpe 'P' complete all as specifiec and as directed.

S&F 110mm bore PVC (SWR) vent cowl complete all as specified and as directed.

S&F in repairs, 100mm x 75mm PVC (SWR) multi floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

M&L for Cutting into existing manholes for connecting new drains of 150 mm internal dia of pipe, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required complete all as specified and as directed.

Excavation in trenches not exc 1.50 m wide and not exc 1.50 m deep for foundation, laying of pipe or for shafts, wells cesspits, man holes, pier holes, laying of cable etc not exc 10 Sqm on plan and n exc 1.5m in depth and getting out in soft / loose soil complete all as specified and as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc. 25 cm in soft / loose soil complete all as specified and as directed.

Removing excavated soil to distance not exc. 50 m and depositing where directed at a level not exc. 1.5 m above the starting point etc complete all as specified and as directed.

S&F GI tubing 25 mm bore, medium grade with all fittings and fixed complete laid in trenches/wall/floor including taking up or down old steel tubing complete all as specified and as directed. Note : Earth work shall be measured and paid separately under respective item.

S&F in repairs, 25mm bore gun metal globe or gate valve cast copper alloy, screwed down, high pressure with iron wheel head screwed both ends for iron pipe complete all as specified and as directed.

M&L for cutting existing steel tubing for alterations or additions (Each cut measured) in 40mm/50 mm bore pipe line complete all as specified and as directed.

Taking down carefully any type of point wiring (light, fan, bell, socket or power), complete excluding fittings but including switches, ceiling roses, pendants, regulators, sockets, etc. and making good disturbed surfaces of walls, ceiling, floors etc to match with existing surface complete all as specified and as directed.

M&L for concealed point wiring with PVC insulated unsheathed multistranded FRLSH copper conductor in and including PVC conduit with cable 1.5 Sqmm size 1100 volts grade conforming to IS:694 and terminate to flush box of required size suitable mounting modular switches and sockets including single core multi stranded FRLSH copper conductor 1.5 Sqmm PVC insulated cable as earth wire connected to earth and common earth dolly drawn in same concealed conduit for one light/fan/wall fan/exhaust fan/bell point controlled by one No, one way 5/6/10 Amp switch complete all as specified and as directed. Note: Cutting chases for concealed type point wiring including making good the same with plaster/putty and Modular boxes with cover plate is deemed to be included in quoted rate.

All as per item serial No 136 here-in-before but for One 3 pin 5/6/10 Amp switch socket outlet on independent board.

All as per item serial No 136 here-in-before but for One 3 pin 5/6/10 Amp switch socket outlet on same board with other switches.

All as per item serial No 136 here-in-before but with 2.5 Sqmm single core multistranded copper conductor cable and earth continuity wire with 2.5 Sqmm cable for 6 pin 15/20 Amp socket outlet on independent board.

S&F Modular switch 1 way 6A/10A, 1 module, single pole 240 volts complete all as specified and as directed.

S&F Modular switch 2 way 6A/10A, 1 module, single pole 240 volts complete all as specified and as directed.

S&F Modular switch 1 way 16A/20A, 1 module single pole 240 volts complete all as specified and as directed.

S&F Modular type socket shuttered type, 6A/10A, 2/3 Pin combined 2 module,240V,AC ISI Marked complete all as specified and as directed.

S&F Modular socket shuttered type, 6A/16A or 10/20Amp, 6 pin combined 2 module complete all as specified and as directed.

S&F Modular Bell push 6A/10A 240 volts, flush type complete all as specified and as directed.

S&F door bell, AC, 230 Volts, single pole complete all as specified and as directed.

S&F Modular stepped type electronic fan regulator, two module size, flush type complete all as specified and as directed.

S&F ceiling rose surface bakelite, 65x50mm three terminal complete all as specified and as directed.

S&F in repairs, intregral LED 4ft luminaire of CRCA / extruded aluminium housing and PC diffuser (Diffuser-Non yellowing type). The luminaire should have a 20 Watt LED with colour consistency SDCM< 5,CRI> 80 and colour temperature - 4000 to 6500K, Luminaire shall be designed to emit at least 2000 nominal lumens at a system efficacy of at-least 120 lumen/watt, power consumption should not be more than 18W (+5%). the life of fixture (including Driver): 50000 burning Hrs.@ L70B50 Lumen maintenance @ design ambient temp 50 deg C. The electronic driver used shall have a power factor >0.95 and THD < 10% suitable for an operating voltage range of 150-270V AC current Ripple<5% internal surge protection should be minimum 2.5KV, electrical insulation class should be Class I &driver should be of class B serviceability. The luminaire should be at least IP20 & IK02 rated. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have in house NABL accredited lab conduct LM79, type test as per IS10322 & "FAT" before dispatch as per IS 10322. The contractor must submit the NABL accreditation certificate for luminaire manufacturer along along with sample approval. The LED Luminaire & It's driver both should be BIS registered contractor shall submit the following reports before supply of material for approvals LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer type test certificate for luminaire as issued by NABL accredited lab, RoHS compliance issued by LED luminaire manufacturer, BIS certificate for LED Luminaire & Driver complete all as specified and as directed.

S&F in repairs, Integral / batten LED 2ft, 10 watt 220 V, luminaire made of CRCA/extruded aluminium housing and PC diffuser (Diffuser-Non yellowing type). The luminaire should have a LEDs with colour consistency SDCM ≤ 5, CRI ≥ 80 and CCT of 6500K. Luminaire shall be designed to emit at least minimum 2000 system lumens at a system efficacy of at-least 120 lumen/watt. Power consumption should not be more than 10W (± 5%). The Life of fixture (Including Driver):50000 burning Hrs. @ L70B50 Lumen maintenance @ design ambient temp 45 deg C. The electronic driver used shall have a power factor 0.95 and THD ≤10%, suitable for an operating voltage range of 140-270V AC, Current Ripple ≤ 5%, Internal surge protection should be minimum 4KV, electrical insulation class should be Class I & driver should be of Class B serviceability. The luminaire shall be IP20 & IK02 compliant.The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322 & "FAT" before dispatch as per IS 10322. The contractor must submit the NABL accreditation certificate for Luminaire manufacturer along with sample approval. The LED Luminaire & it's driver both should be BIS registered. Contractor shall submit the following reports before supply of sample approvals LM79 issued by NABL accrediated lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accrediate lab, RoHS compliance issued by LED luminaire manufacturer, BIS certificate for LED Luminaire & Driver complete all as specified and as directed.

S&F in repairs, LED luminaire 600 mm x 600 mm, 40 watt, 220 V/240V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.

S&F 1200mm sweep BEE 5 star rated, Ceiling fan with Brush Less Direct Current (BLDC) Motor, Class of insulation : B, power factor not less than 0.9, service value (CMM/W) minimum 6.85, Air delivery not less than 230 M³/Min, 350 RPM (tolerance as per IS:374-2019), THD less than 10%,including remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nuts bolts, washers, temperature rise =75 degree C (maximum), insulation resistance more than 2 mega Ohm, suitable for 230V, 50 Hz, single phase AC supply, writing MES No. with black synthetic enamel paint 2 cm high in letter complete with necessary connection up including provision of three core copper flexible cable with flexible wire cover of plastic white in colour and connection from ceiling rose to fan terminal etc complete all as specified and as directed.

S&F exhaust fans AC single phase 230/ 240 V of size 250 mm sweep with louver shutter with frame and necessary fixing accessories , writing MES No. with black synthetic enamel paint 2 cm high in letter complete with necessary connection up including provision of three core copper flexible cable with flexible wire cover of plastic white in colour and connection from ceiling rose to exhaust fan terminal etc complete all as specified and as directed.

M&L for Sub main wiring with 2 runs of 4 sqmm, single core, FRLSH PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 25mm dia non metallic PVC concealed conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 4 sqmm single core FRLSH PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old submain wiring and type of conduit complete all as specified and as directed. Note: (i) 2 run of 4 Sqmm cable and 1 run of 4 Sqmm cable along with conduit altogether shall be measured as one unit. (ii) Cutting chases for concealed submain wiring for the above point and making good in cement mortar is deemed included in quoted rate.

M&L for Sub main wiring with 2 runs of 6 sqmm, single core, FRLSH PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 25mm dia non metallic PVC concealed conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 6 sqmm single core FRLSH PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old submain wiring and type of conduit complete all as specified and as directed. Note: (i) 2 run of 6 Sqmm cable and 1 run of 6 Sqmm cable along with conduit altogether shall be measured as one unit. (ii) Cutting chases for concealed submain wiring for the above point and making good in cement mortar is deemed included in quoted rate.

S&F in repairs, VTPN DB 6 ways double door, fitted with 250 A copper busbar for each phase, having 2 neutral bar and 2 earth bar and cable ties for cable management, fully insulated busbar and shrouded neutral bars as per IEC 61439, suitable for flush mounting, having protection IP-43 and having provision of 1 No. FP MCCB upto 250 Amps as incomer and MCBs as outgoing complete all as specified and as directed. Note: (i) MCCB & MCBs shall be measured and paid separately under appropriate items of this Schedule. (ii) bimetallic thimble shall be used for connection of cable. Make:- L&K Cat No :DEVTH006DD, or Legrand Cat No : 5077 31 or equivalent model of make Siemens/Schnider/HagerABB/Havells

S&F in repairs, MCCB 3P, 100 Amps 415 V, 50Hz, Icu 36 KA, thermal magnetic complete all as specified and as directed. Make:- L&K Cat No :DZ1T0100DXD1A0000, or Legrand Cat No : 4200 85 or equivalent model of make Siemens/Schnider/HagerABB/Havells

S&F in repairs, Single pole & neutral DBs, 12 Ways, double door, protection class IP-43 suitable for mounting MCB, DBs conforming to IEC 61439-3, IS-13032, IS-8623, BS-5484 with min 100 Amp rating copper bus bar complete all as specified and as directed. Make:- L&K Cat No :DESPN012DDS, or Legrand Cat No :5076 12 or equivalent model of make Siemens/Schnider/HagerABB/Havells

S&F in repairs, single pole & neutral DBs 8 Ways, double door, protection class IP-43 suitable for mounting MCB, DBs conforming to IEC 61439-3, IS-13032, IS-8623, BS-5484 with min 100 Amp rating copper bus bar complete all as specified and as directed. Make :- Legrand Cat No 5076 11 or L&K Cat No DESPN008DDS or equivalent model in Siemens / Schneider/Havells.

S&F in repairs, single pole & neutral DBs 4 Ways, double door, protection class IP-43 suitable for mounting MCB, DBs conforming to IEC 61439-3, IS-13032, IS-8623, BS-5484 with min 100 Amp rating copper bus bar complete all as specified and as directed. Make:- L&K Cat No :DESPN004DDS, or Legrand Cat No :5076 10 or equivalent model of make Siemens/Schnider/HagerABB/Havells

S&F RCBO with earth leakage, over load and short circuit proptection, DP, 240 Volts, 40 to 63 Amps, 30 mA senstivity, 4 Module complete all as specified and directed.

S&F MCBs, SP 6 to 32 Amps, 10 KA, 'C' curve IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and as directed.

S&F in repairs, Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp 240V complete all as specified and as directed.

S&F security light bracket made out of GI pipe 32mm dia medium grade (bent to shape as directed ), 1 M long, fixed with MS flat iron clamps made out of 30 mm x 6 mm with nuts, bolts, washers and other connected items of required size, suitable for steel tubular poles/wall and painting with one coat of aluminium paint over a coat of red oxide zinc chrome primer including taking down old bracket complete all as specified and as directed.

S&F in repairs, Bldg security light fittings high-quality group control enabled integrated LED Building security Light with a minimum system lumen of 3000 lm and system wattage 35W with a nominal system efficacy of 120 lumen/watt. The LED used shall have CCT of 5700K, SDCM ≤ 5 and CRI≥70. The housing should be made of LM6/ADC12 Alloy, non-corrosive Single Piece pressure die-cast aluminum, to withstand extreme environments. The spigot shall be part of “Single Piece Pressure Die-cast housing” & shall not be bolted to the luminaire housing to ensure robust design. The name of the brand should be embossed/engraved & should not be mentioned using sticker/screen printing. It should have corrosion resistant powder coating to pass NSS of 500 Hrs. The luminaire LED shall have declared Lifetime of 75K hours@L70. The product should be designed for continuous operation (10-12 Hrs. per day). The Ingress protection should be minimum IP66 & impact resistance shall be IK10. Control gear compartments shall be Top maintainable without accessing/opening the optical compartment. The Luminaire should have a minimum 20 KV/10KA SPD duly bolted in the Luminaire. The SPD should be able to sustain a minimum 15 hits of 10KA rating i.e. Total of 45 hits across all the three modes as per IEEE 62.41.2. The luminaire should be of Class B Serviceability. The LED used in the luminaire shall be SMD type only. The Driver should be asphalt potted & should be a BIS approved driver. The driver shall have operating voltage of 120V to 270V, PF≥0.95 @ full load, THD≤10% @ full load. The driver should be capable of withstand voltage stress of 440V for 8 Hrs., should have an auto shutdown @ 325V(±15V) and have an auto recovery feature. The driver shall comply to IEC61547 & IEC 61000-3-2. The luminaire driver & it’s SPD shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322 & "FAT" before dispatch as per IS 10322. The contractor must submit the NABL accreditation certificate for Luminaire manufacturer along with sample approval. The LED Luminaire & it's driver both should be BIS registered. contractor shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test report for luminaire as issued by NABL accredited lab, RoHS compliance issued by LED luminaire manufacturer, BIS certificate for LED Luminaire & Driver and including making electrical connection using 1.5sqmm, 3 core multi-stranded copper conductor PVC insulated and over all PVC sheathed cable form light fitting complete all as specified and as directed.

Supply, laying and testing XLPE Insulated , PVC sheathed, armoured, heavy duty electric under ground cable, with stranded aluminium conductor, 1100 Volts grade of size 16 sqmm 2 core laid in trenches /floor or fixed on wall/pole in existing or new location including brass compression cable glands, terminal lugs etc,including dismantling of old cable of any description complete all as specified and as directed.

Supply, laying and testing XLPE Insulated , PVC sheathed, armoured, heavy duty electric under ground cable, with stranded aluminium conductor, 1100 Volts grade of size 50 sqmm 3.5 core laid in trenches /floor or fixed on wall/pole in existing or new location including brass compression cable glands, terminal lugs etc, including dismantling of old cable of any description complete all as specified and as directed.

Supply, laying and testing XLPE Insulated , PVC sheathed, armoured, heavy duty electric under ground cable, with stranded aluminium conductor, 1100 Volts grade of size 70 sqmm 3.5 core laid in trenches /floor or fixed on wall/pole in existing or new location including brass compression cable glands, terminal lugs etc, including dismantling of old cable of any description complete all as specified and as directed.

M&L for sand cushioning with dry river sand in trenches for cushioning of underground cable including spreading, leveling, punning down the thickness of sand upto 18cm and consolidated complete all as specified and as directed. Note: Punned thickness of sand cushioning will be measured and paid.

M&L for sub class ‘B’ old size well burnt brick laid flat in trenches with length of brick perpendicular to length of cable, over the cable for protection of LT cable complete all as specified and as directed.

M&L for boring of hole under roads (minimum 1m bellow the road surface) with mechanical arrangement upto 100 mm dia without disturbing the top surface of the road for passing the water pipes/UG cable across the road complete all as specified and as directed.

Supply and laying GI tubing 80mm bore light grade with fittings laid in trenches, on pole and road crossing for protection of LT underground cables complete all as specified and as directed.

Supply and laying GI tubing 50mm bore light grade with fittings laid in trenches, on pole and road crossing for protection of LT underground cables complete all as specified and as directed.

M&L for earthing in replacement complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm buried directly in ground vertically to a depth not less than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers, galvanised steel and protected by GI pipe 15 mm bore light grade & connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 30 cm X 30 cm X 5 cm with 10mm dia TMT bars 8 cm C/c both ways and one handle for lifting made out of 8 mm dia TMT bar, funnel, wire mesh, 20mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown in Electrical Plate No 3 of SSR part -I including dismantling of old earthing complete all as specified and as directed.