CA NO GE(N)AMB-06/2024-25 REPAIR TO JOINERY, PLUMBING, SANITARY, ROOF, PLASTERING AND OTHER CONNECTED BUILDING REPAIR WORKS IN MAINT OF AREA-VI AGE B/R-II UNDER GE (NORTH) AMBALA CANTT

Amount

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillar, etc. but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge.

Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including racking out joints, hacking for key scrubbing down with water, etc. complete all as specified and as directed by the Engineer-in-Charge

Material and labour for rendering 15 mm thick on brick work or concrete wall surfaces in cement mortar 1:4 including mixing water proofing compound @ 2% by weight of cement or as per manufacturer's instruction and finished fair and even without using extra cement complete all as specified and as directed by the Engineer-in-Charge. ( Note- The cost of providing WPC shall be included in quoted rate under this item )

Material and labour for rendering 10 mm thick on any faces of brick work or concrete wall surfaces in cement mortar 1:6 and finishing the surface even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rendering 05 mm thick on fair faces of brick work or concrete ceiling surfaces, chajjas, etc. in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rough cast plaster complete as specified in SSR Part-I, clause 14.22 shall consisting of following:- firstly apply under coat in cement mortar 1:4 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine stone aggregate of size between 6 to 12 mm as per the texture required mixed with coarse sand and cement in the ratio 1:1:1 shall be applied, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new plastered/unplastered surfaces of walls, chajjas, roof projection, etc. and applying two coats of cement base paint complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of newly plastered/ unplastered surfaces of walls and applying two coats of oil bound distemper with painting roller over and including 1 to 2 mm thick wall care putty white cement based in one or two coats to achieve smooth surfaces complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new plastered/unplastered surfaces and applying three coats of white lime wash on surfaces of walls, chajjas, roof projection complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair mild steel powder coated wooden finish curtain rod 25mm dia fixed with and including decorative brackets, two lotto for each rod length at both end, etc. fixed with stainless steel screws complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing PVC connections 15 mm size and 600 mm of length with PTMT nuts and PVC washers on both ends as in repair complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge

Material and labour for galvanised iron tubing 15mm bore, ISI marked, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

Material and labour galvanised iron tubing 20 mm bore, ISI marked, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair bib taps 15mm bore fancy type brass chromium plated with long body, ISI marked, wall flanges and capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair fancy type pillar tap of 15mm bore, cast copper alloy, with capstan heads, ISI marked, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 75mm bore PVC (SWR) multi-floor trap, plain with grating including jointing with solvent cement as in repair complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing as in repair 15mm bore, cast copper alloy, fancy type, chromium plated, ISI marked, stop valves screwed down, high pressure with capstan head, screwed both ends for iron pipe or for unions complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair brass chromium plated tubular towel rail, 20mm dia, 60cm long between flanges complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair 15mm bore cast copper alloy chromium plated angular stop valves, ISI marked, screwed down, high pressure with capstan head, screwed down both ends for iron pipe or for unions complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of vitreous china wash hand basin white with pedestal, ISI marked, flat back of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling chromium plated and 32 mm dia PVC waste pipe including fixing of waste fitting, etc as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair vitreous china squatting pan, Orissa pattern, 580 mm x 440 mm size, white colour with integral foot rest and PVC SWR 'P' or 'S' trap of pressure rating 6 Kg per square cm complete including provision of cement concrete bedding, connection to trap, outgoing flushing pipe, anti syphonage pipe, etc. complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in replacement 10 litre PVC valveless syphonic action type flushing cistern with inlet ball valve float, handle, etc. with and including brackets, flush pipe, etc. and connections of flush pipes to WC complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing for vitreous china wash down water closet pan (pedestal pattern), white (including fixing bolts but excluding flushing cistern and flush pipe) including plastic water closet seat white closed pattern with flat bottom cover and mild steel chromium plated or aluminium hinges device as in repair complete all as specified and as directed by the Engineer-in-Charge.

Taking down existing unserviceable urinal sensor and carrying out necessary repair including replacement of defective parts, make it functional and refixing in the same location complete all as specified and as directed by the Engineer-in-Charge NOTE :- The unit rate includes cost of new parts required for the functioning of Sensor .

Supply and fixing in repair, stainless steel sink without drainage board, 1.00mm thick, ISI marked for kitchen with plug, waste PVC pipe, washers including cantilever cast iron brackets connecting union waste pipe of size 495 mm x 420 mm with bowl size 410 mm x 330mm x 160 mm etc complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of plastic water closet seat cover , white closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminium hinging device as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of 32 mm dia PVC waste pipe for wash hand basin / Kitchen sink etc of standard length as in repair complete all as specified and as directed by the Engineer-in-Charge.

Dismantling water tanks of capacity exc. 250 litre and not exc. 500 litres and removing from site complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing water storage tank, 500 litre capacity, HDPE triple layer, white colour, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm bore high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore, complete all as specified and as directed by the Engineer-in-Charge.

Dismantling water tanks of capacity exc. 500 litre and not exc. 1000 litres and removing from site complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing water storage tank, 1000 litre capacity, HDPE triple layer, white colour, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm bore high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20 mm - 210 gms) as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of 15 mm bore Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe as in repair complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkats or frames with shutter area exceeding 1.50 Square meter and not exceeding 4.00 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkats or frames with shutter area not exceeding 1.50 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description area not exc 2 sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for factory made 2nd class hard wood 35 mm thick plain framed panelled shutter( two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both face . The size of rail and style as per IS:1003 (Part-1) kiln seasoned and chemically pressure treated complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for factory made 35 mm thick 2nd class hard wood glazed and skeleton shutters,open rebated and prepared to receive glass , gauze etc. (without sash bars) ,edges of framing plain chamfered or rounded , fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I, Section-8, clause 8.24 (a) (wood shall be kiln seasoned and chemically pressure treated) complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of solid PVC door frame of size 50mm x 47mm made out of 5mm pre-laminated PVC sheet on single side used instead of plain colour PVC sheet reinforced with MS square tube, edges will be painted to match with pre-laminated sheet and fixed in opening complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of factory made solid PVC moulded door shutters with particle board core 28 to 30 mm thick (styles) with 2, 4, or 6 raised panel design with 2 mm thick pre-laminated moulded PVC sheet on the front face and 2mm thick plain colour PVC sheet on back face fixing in frame at site as per specification and drawing complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rolled mild steel framed work as in chowkats of door or gates of angle or other section with gusset plates, rails braces etc. complete. drilled for fixing for steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and including either hooks and hinges and hanging ,door fitting (exclusive of steel sheeting or other covering, running rails and guides) also fastening and fixing conforming to Fe-290-W (Gde E-165) quality 'A' complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate as in holdfasts complete all as specified and as directed by the Engineer-in-Charge.

S&F double shutter steel window box type ERW hollow P section comprising of glazed/gauged skeleton shutter fabricated from following sections :- (a) ERW hollow P section frame of size 60 mm x25 mm made from 1.25 mm thick MS sheet (02 Nos i.e. 01 for glazed shutter and 01 for gauzed shutter ). Both P section shall be welded with flat iron 25x03 mm thick all around of frame on both inner and outer faces . (b) Style and rails of window shutters shall be fabricated with ERW hollow P section of size 50 mm x25 mm made from 1.00 mm thick MS sheet and comprising of 02 Nos sash bars for glazed window leaf of T – section 20 x 03 mm thick and one No sash bar of 20 mm x 3 mm thick section for gauzed winodw leaf . (c) Vertical mullion shall be ERW hollow T -section of size 60 x 25 mm made from 1.25 mm thick MS sheet (d) The above steel window shall be deemed to include the following accessories/ fittings : i) Hold fast 150mm long mild steel flat iron 12x3 mm thick made to shape- 04 Nos per window ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. iii) MS tower bolt stove enamelled 150mm long- 2 Nos per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 No per leaf. (v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 No per leaf

item No. 47 (contd....) vi) Pintal hinges 12 x 75 mm - 2 Nos each leaf vii) 10mm square Guard bar @ 10 cm c/c welded to frame . (viii) Two coat of Synthetic enamel paint over one coat of red oxide primer. (ix) 0.36mm nominal dia of stainless steel wire mesh and average width of aperture of 1.40mm fixed in gauzed skelton shutter of window with flat iron 15 x 03 mm with steel screws . (x) 3mm thick sheet glass, ordinary quality and with oil putty in square n. exc 0.5 sqm in each pane fixed in glass shutter of window. (xi) Fabrication and fixing arrangements as per specification including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed. Notes : (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery, grill and other accessories as mentioned above. (iii) The window upto 1.00 metre width shall consists of two leaves both for gauzed shutter and glazed shutter and all the shutters are openable. The window more than 1.00 metre width shall have two openable leaves on both outer side for gauzed shutter and glazed shutter and middle leaf/shutter shall be fixed type.

Supply and fixing of 150 mm long aluminium handle cast type anodised complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of 200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of 250mm long aluminium alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloys to door shutter complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of butt hinges 100mm long of stainless steel, medium weight, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of mild steel helical door spring 150 mm long fixed with screws to wooden chowkats or welding to steel chowkats, complete all as specified and directed by the Engineer-in-Charge.

Resecuring or easing & adjusting shutters of any description exceeding 1.00 sqm and not exceeding 2.00 Sqm each, without taking down shutters complete all as specified and as directed by the Engineer-in-Charge

Taking down carefully steel door shutter exceeding area 1.00 sqm but not exceeding 2.00 Sqm including cutting, welding and adjusting as per opening and refiixng the same at same location complete all as specified and as directed by the Engineer-in-Charge (new angle iron etc shall be measured and paid for separately)

Material and labour for running welding in repairs, thickness of metal to be welded not exceeding 6mm complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by the Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds and steel window frame glazed with putty or fixed with beads complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for sheet glass 3.0mm thick ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified by the Engineer-in-Charge.

Supply and fixing 4mm thick glass ground or obscured or frosted on one side, in square not exceeding 0.5 Square metre each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified by the Engineer-in-Charge.

Supply and fixing of stainless steel wire cloths 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair stainless steel wire cloths 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Non Skid coloured ceramic tiles joint free premium/1st quality 7 to 8 mm thick, (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Non Skid coloured ceramic tiles joint free premium/1st quality of same description as of floor tiles in serial item No. 65 above but 100mm to 200mm height as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for glazed ceramic coloured tiles joint free premium/1st quality in vertical surfaces/skirtings/dados of size 300x450 x7mm or 300x 600x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick/concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for vitrified ceramic double charged light shade tiles, 1st quality, (square/rectangular), 10mm thick, area of each tile exceeding 0.36 sqm and not exc 1.00 sqm as in floor, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for vitrified ceramic double charged light shade tiles, 1st quality, (square/rectangular), 10mm thick, of same description as of floor tiles in serial item No. 82 above but 100mm to 200mm height as in skirting, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including rendering 10 mm thick in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 25 mm thick PCC 1:2:4, type B0 as in sub base of floor (using 12.50mm graded crushed stone aggregate), finished even & fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge. Note- This item shall not be executed in the location, where dismantling of tiles work have been done.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified & directed by the Engineer-in-Charge.

Supply and fixing 110mm dia UPVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall, complete all as specified and directed by the Engineer-in-Charge..(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing of 110 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of 75mm dia UPVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall, complete all as specified and directed.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing of 75 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified. (Note- UPVC bends shall be confirm to BS 4515 DIN 19531 and DIN 19534)

Material and labour for cleaning and removing all scale and dirt etc from PVC/RCC tanks and mouths of circulating pipe of capacity 250 litre and upto and including 1000 litre & writing on the tank with synthetic enamel paint not less than 70mm long and 2mm wide of words in shape like cleaned on : 15.06.2018 complete all as specified and as directed by the Engineer-in-Charge. NOTE :- The unit rate shall be included cost of small fittings such as elbow, socket, reducer, tee, union, etc.

Supply and fixing of chromium plated Brass wash hand basin mixer for mixing hot and cold water screwed down for 15mm dia pipe including waste popup with 450mm long braided hoses and all connecting fittings as in repair complete fixed all as complete all as specified and as directed by the Engineer-in-Charge. Make :Jaquar Cat Part No QQP-7167BPM / Cera Cat Part No.F2007461 / Hindware Cat Part No.F 480011

Supply and fixing in repair brass chromium plated concealed stop cock with long shank with fitting sleeve, operating lever and adjustable wall flange screwed down,high pressure with crutch handle, screwed down both ends for iron pipe or for unions 15mm bore of make:- Jaquar cat part No.CON-083FTK or Hindware cat part No. F280027 complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing brass chromium plated wall mixture 3-in-1 system with provision for both hand shower and overhead shower complete with 115 mm long bend pipe , connecting legs & wall flange without hand & overhead shower as in repair complete all as specified and as directed by the Engineer-in-Charge. Make :Jaquar Cat Part No QQT-7309 /Hindware Cat Part No.F 120019

Supply and fixing in repair brass chromium plated soap dispenser with glass bottle complete all as specified and directed by Engineer-in-Charge. Make- Jaquar/Hindware/CERA

Supply and fixing brass chromium plated Towel ring round between flanges including fixing with brass screws complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : ACN-1121BN/Cera Cat Part No.F5007105 / Hindware Cat Part No.F 880007

Supply and fixing brass chromium plated SOAP DISH HOLDER including fixing with brass screws to wall complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : ACN-1131N/Cera Cat Part No.F500716 / Hindware Cat Part No.F 840006

Supply and fixing in repair overhead shower 200mmx200mm square shape single flow ABS body chrome plated with grey face plate with Rubit clean system complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair corner glass shelf (with bracket) including fixing with brass screws to wall complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : ACN-1173/Cera Cat Part No.F5005101 / Hindware Cat Part No.F 890009

Supply and fixing in repair brass chromium plated hand shower ( health faucet) with 8 mm dia 1.2 mtr long flexible tube and wall hook with NRV ( back flow preventer ) complete fixed to wall complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : ALD577/Cera Cat Part No. F8030101

Supply and fixing in replacement counter top vitreous china wash hand basin white of size 515mmx365mmx120mm, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of waste fitting etc as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No FLS -WHT-5931 /CERA Cat part No.S2020108 /Hindware Cat Part No.91041

Supply and fixing of single piece water closet wtih PP soft close seat cover, hinges, fixing accessories and accessories set, cistern fittings, S or P Trap complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No SLS -WHT-6855S /CERA Cat part No.S10131095 /Hindware Cat Part No.92099 (S-30)

Supply and fixing of brass CP toilet paper holder including fixing with brass screws to wall complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : AKP-35753PS/Cera Cat Part No.F5007109 / Hindware Cat Part No.F 840009

Supply and fixing of aluminium (Die-cast) body hydraulically door closer regulated, designation No.3, universal type, suitable for door shutters of 851 mm to 1000 mm in width and weight between 61 to 80 Kg as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty as in repair complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for repairing of all type aluminium window/door shutter with frame and refixing it after resecuring its frame work by means of tightening with new screw ,cleats, rubber gasket and refixing in the same opening complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of powder coated aluminium section (minimum thickness of powder coating 50 micron) for chowkats, doors shutter comprising of the following section including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/panelling, C.P. brass/ stainless steel screws complete all as specified and as directed by the Engineer-in-Charge:- (a) Door frame single groove 101.6mm x 44.45mm x 2.50mm thick (b) shutter top 47.62mm x 44.45mm x 1.95mm thick (c) shutter bottom 114.30mm x 44.45mm x 2.15mm thick (d) shutter vertical 85mm x 44.45mm x 1.80mm thick (e) shutter middle 83.5mm x 44.45mm x 2.40mm (f) Gauging clip weighing not less than 0.097Kg/matre Note : (a). Glazing/wire mesh shall be measured and paid separately; (b). The rates quoted shall be inclusive of neoprene beading, glazing clips, jointing clips, screws, etc as required. (c). The rates shall be inclusive of locking arrangement with mortice lock of brass, vertical type,100mm size, 4 lever, ISI marked with duplicate keys and handle including complete packing with silicon gel all round contacting surface of aluminium framework and including matching the existing surface area complete all as specified and directed.

Supply and fixing of powder coated aluminium section (minimum thickness of powder coating 50 micron) for doors,windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/panelling, C.P. brass/ stainless steel screws complete all as specified and as directed by the Engineer-in-Charge. Note : (a). Glazing shall be measured and paid separately; (b). Weight of aluminium sections shall be as per IS or actual weight which ever less shall be measured. (c). The rates quoted shall be inclusive of neoprene beading, glazing clips, jointing clips, screws, etc as required and the same shall not be measured for arriving the weight; (d). The rates shall be inclusive of locking arrangement including complete packing with silicon gel all around contacting surface of aluminium framework and including matching the existing surface area complete all as specified and directed.

Supply and fixing for aluminium alloy anodized (powder-coated) window frame with double shutters open able type, with aluminium sections as per of “Jindal” section numbers for casement windows with double shutters including aluminium alloy anodized snap type beads, handles, aluminium anodized barrel tower bolts and glazing clip, joint cleats, rubber gaskets etc., complete all as specified for series-B “ Jindal” section numbers for casement (a)Frame of section 101.6mmx44.45mmx2.10mm thick and section for shutter 47.62x44.45x1.95 mm thick (b) Mullion 53mmx52mmx 2mm thick not less than 1.065 kg/mtr. (c) Glazing clip weighing 0.259kg/mtr. (d) Windows shall be provided with 02 Nos. of tower bolt for single leaf and 03 Nos. of tower bolts for double leaf. Tower bolts shall be aluminium alloy anodized weighing 0.302kg/mtr. Handles shall be aluminium anodized ‘D’ type handle of size 98mm and thickness 2.37mm weighing 0.875kg/mtr and one no per each open able leaf shall be provided. (Note : 1. The rates shall be inclusive of provision of and fixing of rubber packing/gasket. Glass pane and wire gauge shall be measured and paid for separately.

Material and labour for 12 mm thick pre-laminated particle board interior grade pre-laminated both side with decorative choice lamination fixed with screw to timber frame work/aluminium frame work complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 4mm thick glass ground or obscured or frosted on one side, in square not exceeding 0.5 Square metre each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified by the Engineer-in-Charge.

Supply and fixing aluminium anodized grill (anodized transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/ pattern, 5.5mm thick, weight not less than 2.5kg per square (in the shape of expanded metal aluminium xpm jalli) opening size length of expansion (60mm) and width expansion 45mm fixed in aluminium anodized window with ‘F’ channel of handle section with screw, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of EPDM rubber/ neoprene gasket in glass pane from existing aluminium windows/ventilators/doors including taking down old/defective neoprene gasket complete all as specified and as directed by the Engineer-in-Charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) or insulation boards/slabs/blankets, any thickness including cover fillets and false ceiling frame work of any size/ description complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of boarding of any description and in any position of any size complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 18/19mm thick block boards,for cup board shutters , grade 2 quality, interior grade, commercial type fixed with screws to timber frame work complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 6mm thick (3 ply) plywood, grade BWR, type BB, fixed with screws to timber frame work complete all as specified and as directed by the Engineer-in-Charge

Material and labour for 4mm thick (3 ply) veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber frame work complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing of GI Metal Suspended ceiling of approved materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm centre to centre and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm centre to centre along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, and as directed by Engineer-in-charge. GI Metal Ceiling laying perforated Tengular edge global white colour tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fibre acoustical fleece. Note- Ceiling tiles and ceiling grid shall be of the same make.

Supply and fixing of 5mm PVC hollow sheet (the thickness of inner wall 0.7 to 1.00mm) wall panelling inclusive of solvent cement and fixing at site with U clip or PVC frame as per specifications and drawing complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of old decorated brick/concrete, plastered / unplastered surfaces of ceiling by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white lime wash on prepared surfaces of ceiling etc. complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of old decorated brick/concrete, plastered / unplastered surfaces of ceiling by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil bound distemper with painting roller over prepared surfaces of ceiling etc. complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of old decorated brick/concrete, plastered / unplastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil bound distemper with painting roller over prepared surfaces of walls pillars, cornices etc. complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for complete removal of existing treatment on wall by scrappers or any other means and washing , rubbing down and stopping complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 1-2mm thick wall care putty white cement based in two or more coats to achieve smooth surface over prepared surface complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of putty surfaces and applying two coats of oil bound distemper with painting roller over prepared surfaces of walls, pillars, cornices etc. complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of plastic emulsion paint with painting roller complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of old decorated brick/concrete, plastered / un--plastered surfaces of walls and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of old decorated brick/concrete, plastered / unplastered surfaces of walls, pillars cornices etc by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots, filling all holes and cracks with white cement based wall care putty and applying one coat of cement base paint on the walls, pillars, cornices etc. complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of old decorated brick/concrete, plastered / unplastered surfaces of walls, pillars cornices etc by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots, filling all holes and cracks with white cement based wall care putty and applying two coat of cement base paint on the walls, pillars, cornices etc. complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of old wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed by the Engineer-in-Charge.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings including ridges complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick, having Zinc coating 150 gm per sqm (Az-150) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, having Zinc coating 150 gm per sqm (Az-150) as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of timber scantlings 40 sq cm and over in section, in any position, unframed work complete all as specified and directed by the Engineer-in-Charge.

Supply and Fixing mild steel work as in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St-240 complete all as specified and as directed.

Note:- Amount of credit of Rs. 89,010.00 for retrieved materials is mentioned in Schedule of Credit Page No. 140 (R) & 141 (R) of tender documents in pdf form which will be deducted offline while acceptance of tender.

Jai Bala Ji

peeyush construction and engineering co

bhagwandasswazirchand

Durga Enterprises

Swami Enterprises

SMT Construction

VIJ ENGINEERS