Construction of 6 Nos. Type-II Residential Quarters for Staff of Fire Brigade at Kangra

Amount

Excavation in foundation, trenches etcetra in earth work in all kind of classification of soil such as pick work, jumper work, pick jumper work, blasting work, soft and hard blasting and doing work in saturated soil, including chiselling or wedging out rocks where blasting work is prohibited or any other mixed variety of soil includinjg shoring, strutting, de-watering and pumping or bailing out water (surface and sub soil water) upto any depths or any quantum of water including slush which may arise during de-watering or removal of slush, lift upto any height stacking the excavated soil clear from the edge of excavation and then returning the stacked soil in 15cm (Fifteen centimetre) layers, when required into plinths, sides of foundation etcetra consolidating each deposited layer by ramming, watering and then disposing of all surplus excavated earth as per specification, approved drawings, design as per the entire satisfactions and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Filling in Plinth with sand under floors including watering ramming consolidating and dressing complete, as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Boulder filling under floors including watering ramming consolidating and dressing complete, as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm. (Three decimal one five milimetre) thick welded with angle iron frame of 30x30x5mm (Thirty milimetre into thirty milimetre into five milimetre ) so as to give a fair finish including centering, shuttering, strutting and propping etcetra with wooden battens and ballies for all heights/depths of propping and centering below supporting floor to ceiling for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in Foundation, footings bases of columns etc. for mass concrete, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm. (Three decimal one five milimetre) thick welded with angle iron frame of 30x30x5mm (Thirty milimetre into thirty milimetre into five milimetre ) so as to give a fair finish including centering, shuttering, strutting and propping etcetra with wooden battens and ballies for all heights/depths of propping and centering below supporting floor to ceiling for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in Columns, Pillars, Piers, Abutments, Posts and struts, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm.(Three decimal one five milimetre) thick welded with angle iron frame of 30x30x5mm.,(Thirty into thirty into five milimetre)so as to give a fair finish including centring,shuttering, strutting and propping etcetra with wooden battens and ballies complete upto all heights/ depth of propping and centering below supporting floor to ceiling for all height and removal of the same for insitu- reinforced concrete and plain concrete work in Flat surfaces such as soffits of suspended floors, roofs, landings and the like, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron frame of 30x30x5mm(Thirty into Thirty into Five millimeters),so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies for heights of propping and centring below supporting floor to ceiling for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers, girders lintels, sides, and soffits of beams, beam, hunchings, cantilevers, bressumers and lintels upto all depths, as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm. (Three decimal one five milimetre) thick welded with angle iron frame of 30x30x5mm (Thirty milimetre into thirty milimetre into five milimetre ) so as to give a fair finish including centering, shuttering, strutting and propping etcetra with wooden battens and ballies for all heights/depths of propping and centering below supporting floor to ceiling for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in Edges of slab and breaks in floors and walls under any thickness, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm. (Three decimal one five milimetre) thick welded with angle iron frame of 30x30x5mm (Thirty milimetre into thirty milimetre into five milimetre) so as to give a fair finish including centering, shuttering, strutting and propping etcetra with wooden battens and ballies for all heights/depths of propping and centering below supporting floor to ceiling for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in vertical surfaces such as walls any thickness partition and the like including attached pilasters, buttresses, plinth string courses and the like, as per specifications, approved drawing, design, as per entire satisfactions and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm. (Three decimal one five milimetre) thick welded with angle iron frame of 30x30x5mm (Thirty milimetre into thirty milimetre into five milimetre) so as to give a fair finish including centering, shuttering, strutting and propping etcetra with wooden battens and ballies for all heights/depths of propping and centering below supporting floor to ceiling for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in stair cases with slopping or stepped soffits excluding landing, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete 1:4:8 ( One Cement isto four Sand isto eight graded crushed stone aggregate 40 mm (forty milimetre) nominal size mechanically mixed and curing complete excluding the cost of form work. in foundation and plinth, as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying reinforced cement concrete work of grade M-20 (M- Twenty) design mix to obtain the minimum compressive strength of 20N/mm2 (Twenty newton per square millimetre) with cement contents not less than 330 Kgs/m3 (three hundred thirty kilogrammes per Cubicmetre) mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced concrete work in foundation footings, bases of columns and the like and mass concrete in all depths/thickness above plinth to all floor levels, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying reinforced cement concrete work of grade M-20 (M- Twenty) design mix to obtain the minimum compressive strength of 20N/mm2 ( Twenty newton per square millimetre) with cement contents not less than 320 Kgs/m3 (three hundred twenty kilograms per Cubicmetre) mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced concrete work in suspended floor roofs, landing and shelves and their support balconies, lintel beams, girders, breassumers and cantilever for all depth/thickness plinth to all floor levels, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying reinforced cement concrete grade M-20 (M-Twenty) design mix to obtain the minimum compressive strength of 20 N/mm² (twenty newton per square milimetre) with cement contents not less than 320 kgs/cum (Three hundred twenty Kilograms per Cubic metre) mechanically mixed and vibrated including curing complete excluding cost of form work and reinforcement for reinforced concrete work in columns, pillars, posts and struts in all depth/ thickness above plinth level to all floor level, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying reinforced cement concrete work of grade M-20 (M- Twenty) design mix to obtain the minimum compressive strength of 20N/mm2 ( Twenty newton per square milimetre) with cement contents not less than 320 Kgs/m3 (three hundred twenty kilogrammes per Cubicmetre mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced concrete work in stair cases (except spiral stair cases) excluding landing but including preparing of top surface and finishing of nosing upto floor all levels, as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying reinforced cement concrete grade M-20 (M-Twenty) design mix to obtain the minimum compressive strength of 20 N/mm² (twenty newton per square milimetre) with cement contents not less than 320 kgs/cum (Three hundred twenty Kilograms per Cubic metre) mechanically mixed and vibrated including curing complete in reinforcement work for reinforced concrete work in chajjas any thickness above plinth level to all floor level including finishing the exposed surfae with cement mortar 1:3 (One cement isto Three Sand) to give a smooth and even surface including centring/ form work and curing complete but excluding the cost of reinforcement, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax,GST or any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the minimum compressive strength of 20N/mm² (twenty newton per square milimetre) with cement contents not less then 320 kg (Three hundred twenty kilogram) per cubic metre, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in walls any thickness including attached buttresses, pilasters and their caps bases and string courses etcetra as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, GST or any other taxes imposed by the Government.

Providing and laying Tor steel of TATA/ SAIL/TISCO reinforcement for Reinforced cement concrete work including cutting, straighting, bending, binding and placing in position, including cost of binding wire complete for all floor level, as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Second class brick masonry in common burnt clay building bricks in super structure above plinth level to floor any level in cement mortar 1:6 (One Cement is to Six Sand), as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Second class brick masonry in common burnt clay building bricks in foundtion and plinth in cement mortar 1:4 (One Cement is to Four Sand), as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Second class half brick masonry using common burnt clay building bricks in super-structure above plinth level to floor all level in cement mortar 1:4 (One cement isto four sand) and curing complete, .as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing M.S. Channels in doors and windows frames manufactured from M.S. Channels section 75x40x4mm (Seventy five into Forty into Four milimetres) and M.S. Flat 75x40mm (Seventy five into Forty milimetres) combination as per design drawing including hinges jambs, beeds if required thrashold of M.S. angles 50x25mm (Fifty into Twenty five milimetre) welded or rigidly fixed by mechanical means lugs, with split ends tails to each jambs including steel butt hinges 2.5mm (Two decimal Fiv e milimetres) thick with a provision of locking arrangements shock observers and specified and applying a cost of approved steel primer after pretreatment of surfaces within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate includes, royality charges, octroi, GST, malkana and all other taxes as imposed by the Government.

Providing and fixing factory made double steel shutter windows side hung (one glazed and other wire gauged) including frame of channels ISLC-75x40mm (Seventy five into forty milimetre) flapped with mild steel flat 75mm (Seventy five millimetres) and 50x40mm (Fifty into fortyr millimetres) in the opening side of channels to make multi frame and shutter of rolling steel Z-section and T-section and T-hinges, Handles with closing device and making provision of fixing of window (where required) with 16x3.15mm (Sixteen into three point one five millimetres) lugs 10cm (Ten centimetres) long embedded in cement concrete block 15cmx10cmx10cm (fifteen centimeters into ten centimeters into ten centimeters) size of 1:3:6 (One cement isto three sand isto six graded crushed stone aggregate 20mm (Twenty millimetres) nominal size) or with wooden/steel plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required and iron fittings including providing and fixing 4mm (four millimetres) thick glass panes with glazing clips and special metal sesh putty of approved make for glazed shutter and metal beading with screws etcetera and including fixing of wire gauge shutter using galvanised M.S. wire gauge of IS gauge designation 85-G (Eighty five-G) with wire of 0.56mm (Zero point five six millimetres) and for fixing wire mesh with M.S. flats 20mmx3mm (Twenty millimetres into three millimetres) for beading and screws and applying a priming coat of approved steel primer after pretreatment of the surfaces as directed by Engineer-in-Charge, including carriage of materials within all leads and lifts and other incidentals. The rate includes, royality charges, octroi, GST, malkana and all other taxes as imposed by the Government.

Providing and fixing steel glazed doors, windows and ventilators of various type categorized below, of standard rolled steel sections joints mitred and welded with 16x3.15mm (Sixteen into three decimal one five millimeters) lugs 10cm (Ten centimeters) long embedded in cement concrete block 15x10x10cm (Fifteen into ten into ten centimeters) size of 1:3:6 (One cement is to three sand is to six graded stone aggregate 20mm (Twenty millimetres) nominal size) or with wooden/steel plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required and iron fitting such as handles, tower bolts etc. including providing and fixing of glass panes 4mm (Four millimetres) thick with glazing clips and special metal sash putty of approved make complete including applying priming coat of red lead paints and carriage of materials within all leads, lifts of materials and other incidental Charges. The rate includes, royality charges, octroi, GST, malkana and all other taxes as imposed by the Government. (a) Fixed steel window.

Providing and fixing angle iron doors, windows clerestory windows frame (single rebate) manufactured from M.S. angle iron section of 40x40x6mm (Forty into forty into six millimetres) thickness and M.S. flat 50x5 (fifty into five millimetres) as per design and drawing including hinges, jambs lock, jambs beeds and if required angles thrashold of M.S. angle 50x25mm (Fifty into twenty five millimetres) welded or rigidly fixed by mechanically means lugs with split ends tails to each jambs including steel butt hinges 2.5mm (two point five millimeters) thick with a provision for locking arrangements and shock observer as specified and applying coat of approved steel primer after pre-treatment of the surfaces complete, including carriage of materials within all leads, lifts and other incidental Charges. The rate includes, royality charges, octroi, GST, malkana and all other taxes as imposed by the Government.

Complete box of Cup board shall be made of 25mm (Twenty five milimetre) thick water proof termit resistance commercial board of Uni ply/ Green ply/ Cooture ply/ Kit ply/ Dura ply/ Marine Back side of cup board shall have 6/8mm (Six oblique Eight milimetre) thick water proof ply and shelves of cup board should have 19mm (Nineteen milimetre) thick water proof commercial board of Uni oply/ Green ply/ Centry ply/ Kit ply/ Dura ply and shutter with hard wood edging to be finishing with 1mm (One milimetre) thick limination of Century/ Greenlam/ Action Lesa/ Merinolam of approve shade. All the cut portion of the board shall have 6mm (Six milimetre) hard wood edging/ lipping including necessafry handle, knobs, hinges and menetic catcher and filling complete in all respect, as per specification, approved drawing, design. The rate includes, royality charges, octroi, GST, malkana and all other taxes as imposed by the Government.

Providing and fixing plain M.S. (Mild steel) Grills of required pattern in structural steel frames of windows etcetera with Mild Steel flats square or round bars with headed bolts and nuts or screws including welding with frames complete in all respect, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 12mm (Twelve milimetre) prelaminated board both side bwp phenol bonded exterior/interior grade panelled shutters with frame of first class deodar wood for doors including bright finished /black enamelled iron butt hinges with necessary screws 40mm (Forty milimetre) thick frame, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, GST or any other taxes imposed by the Government.

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of IS gauge designation 85-G with a wire of dia 0.56(Zero decimal Fifty six milimetres) for doors and windows and clerestory windows including bright finished black enameled iron hinges with necessary screws 40mm (Forty milimetres) 2nd class deodar wood, within all leads and lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 18mm (Eighteen milimetre) thick 150mm (One hundred fifty milimetre) wide deodar wood pelmet with 25 mm (Twenty five milimetre) diameter wooden curtain rods and brackets including fixing 25x3mm (Twenty five into Three milimetre) M.S. flat at 10 cm (Ten centimetre) long and plugs etc. complete in first class deodar wood. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals. The rate including octroi, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing and fixing 300x16mm(Three hundred into Sixteen milimetres) size anodized aluminum sliding door bolts make of PILOT/ SHEEL anodized transparent or dyed to required colour and shade with bolts and nuts necessary screws etcetra complete, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 200x10mm (Two hundred into Ten milimetre) oxidized M.S. Tower bolts (Barrel type) with necessary screws etc. Complete, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 100x10mm (One hundred into Ten milimetre) oxidized M.S. Tower bolts (Barrel type) with necessary screws etc. Complete, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 125mm (One hundred twenty five milimetres) size aluminium anodized make of PILOT/ Sheel handles anodized transparent or dyed to required colour and shade with necessary screws etcetra complete, as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred milimetres) size aluminium anodized make of PILOT/ Sheel handles anodized transparent or dyed to required colour and shade with necessary screws etcetra complete, as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred millimetres) bright finished brass floor door stopper with rubber cushion and necessary screws etcetera to suit shutter thickness complete, including carriage of material within all leads, lifts and other incidentals. The rate includes, royality charges, octroi, GST, malkana and all other taxes as imposed by the Government.

Providing and fixing oxidized M.S. Hooks and eyes 150mm (One hundred fifty milimetre), as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying 60mm (Sixty milimetre) thick heavy duty precast cement concrete inter locking paver block of NTC PVC/Fibre mould vibro compacted upto M-50 (M-Fifty) grade including border or kurb block grey or coloured of approved design and design laid over sub base of concrete with 25mm (Twenty five milimetre) thick average thickness of cement mortar 1:4 (One cement isto Four Sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks including curing, rubbing and polishing complete (Sub base concrete floor to be paid for separately), as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, GST or any other taxes imposed by the Government.

Providing and laying polished Baroda Green marble slab on work top of all counters over 20mm (Twenty milimetre) thick base in cement mortar 1:3 (One cement isto Three sand) including jointing with cement mortar 1:2 (One white cement isto Two marble dust) with an admixture of pigment to match the shade of the marble with round nosing rubbing and polsihing complete upto all floor levels, as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 600x600x10mm (Six hundred into six hundred into Ten milimetre) full body Matt finish double charge/ Ultra charge vitrified tiles Kajeria/Elermity/ Nitco/Jonson/Simpolo/ Restile or its equivalent in flooring, on a bed of 12mm (Twelve milimetre) thick cement mortar 1:3 (One cement isto Three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete upto all floor level, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying Duro stone vetrified tiles make of Kajaria, NITCO, Somany orient, RAK, Johanson & Johanson {(300x300mmx8mm) (Three hundred into Three hundred into Eight milimetre) in grey/coloured of required shade in skirting risers of steps and dados on 12mm thick cement mortar 1:3 (One cement isto Three Sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete any floor level/ height as per the direction by the Engineer in charge as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 18 mm (Eighteen milimetre) thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (One cement isto Four coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour and shade Area of slab upto 0.50 sqm and as per the direction of the Engineer-in-Charge and carriage of material within all leads, lifts and other incidental . The rate including octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing and fixing 85 cm high rail having baluster of 19mm x 19 mm (Nineteen milimetre into Nineteen milimetre) size and 12mm x 12 mm (Twelve milimetre into Twelve milimetre) MS solid square bars in combination with with M.S. flat of 40 mm x 5 mm (Forty milimetre into Five milimetre) size with PVC hand rail baluster dully welded/jointing with electric gas welding with top M.S. Flat and as per the direction of the Engineer-in-Charge and carriage of material within all leads, lifts and other incidental . The rate including octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing and fixing on wall face 110mm (One hundred ten milimetres) diameter P.V.C. polyvinyl chloride D-plast or equivalent rain water pipes of working pressure not less than 4.50 kg (Four point five zero kilogrammes) per Square Metre including filling the joints with approved adhesive including carriage of materials within all leads, lifts and other incidental Charges. The rate includes, royality charges, octroi, GST, malkana and all other taxes as imposed by the Government.

Providing and fixing on wall face 150mm (One hundred fifty milimetres) diameter P.V.C. polyvinyl chloride D-plast or equivalent rain water pipes of working pressure not less than 4.50 kg (Four point five zero kilogrammes) per Square Metre including filling the joints with approved adhesive including carriage of materials within all leads, lifts and other incidental Charges. The rate includes, royality charges, octroi, GST, malkana and all other taxes as imposed by the Government.

Providing and fixing Plain bend 110mm (One hundred ten milimetre) diametre on wall face C.I. accessories for rain water pipes including filling the joints with spun yarn soaked in neat cement slurry and cement mortar 1:2 (One cement isto Two Sand), as per the direction of Engineer-in-Charge, including carriage of materials within all leads, lifts of materials and other incidentals. The rate includes, royality charges, octroi, GST, malkana and all other taxes as imposed by the Government.

Providing and fixing Mild Steel holder bat clamps of approved design to P.V.C. (Poly Venyl Chloride) rain water pipe 110mm (One hundred ten milimetre) size embedded including cement concrete blocks 10x10x20cm (Ten into Ten into Twenty centimetre) of 1:2:4 (One Cement isto Two Sand isto Four graded crushed stone aggregate 20mm (Twenty milimetre) nominal size and cost of cutting holes and making good the walls etcetra, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

6mm (Six millimetres) thick cement plaster to ceiling with cement mortar 1:4 (One cement isto Four Sand) upto all floors level complete, as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, GST or any other taxes imposed by the Government.

15 mm (Fifteen milimetre) thick cement plaster in single coat on rough side of brick/concrete/stone walls for interior plastering up to all floor level including arises, internal angles, chamfers and rounded angles any girth and finished even and smooth with cement mortar 1:6 (One cement isto Six sand) as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

15 mm (Fifteen milimetre) thick cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering up to all floor level including arises, internal angles, chamfers and rounded angles any girth and finished even and smooth with cement mortar 1:6 (One cement isto Six sand), as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

15 mm (Fifteen milimetre) thick cement plaster in single coat on rough side of brick/concretes/ stone walls for interior plastering up to all floor level including arises, internal angles, chamfers and /or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth with cement mortar 1:3 (One cement isto Three sand), as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, GST or any other taxes imposed by the Government.

Applying Birla J.k. white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dirt, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete upto all floor level, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, GST or any other taxes imposed by the Government.

Applying one coat of Acrylic primer (spectrum or equivalent of superior quality) on new concrete/ masonry/ plasterede surfaces after and including preparing the surface by thoroughly bruhsing the surface free from mortar dropping and other foreign matters sand papering the surface smooth complete, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, GST or any other taxes imposed by the Government.

Finishing wall with weather proof exterior grade emulsion of Dune finish of NCL Altack/ Spectrum Texture wall finish natural Grit of heritage approved design/shade on undecorated wall surfaces (two coats) to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt dust and other foreign matter etcetra including sand paper, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Wall painting (two coats) with acrylic premium emulsion paint of Asian/Nerolac and manufacture of approved shade for interior grade on undecorated concrete/ stone/ plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty as required for making the surface complete, including carriage of materials within all leads, lifts and other incidental Charges. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing Plinth protection 50mm(Fifty milimetre) thick with cement concrete 1:3:6 (One cement isto Three sand isto Six graded stone aggregate 20mm (Twenty milimetre)nominal size including finishing the top surface of concrete smooth within all leads and lifts of material and other incidentals as per the direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing under layer for Plinth protection of 75 mm (Seventy five milimetre) thick unconsolidated) bed of dry brick stone broken aggregate 40mm (Forty Milimetre) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground within all leads, lifts of material and other incidentals as per the direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying coat of approved steel primer using structural steel etc. as required in grating, frames, guard bar, ladder, railing, brackets, gates and similar works and as per the direction of Engineer-in-Charge including carriage of material within all leads and lifts and other incidental. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing and fixing 0.60mm (Zero decimal six zero milimetre) thick prepainted steel sheet of TATA/Sail/Reliance/Jindal in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (Twenty) microns over 5(Five) microns primer coating to back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted J or L hooks, bolts and nuts of size 6mm dia (Six milimetre diameter) with prepainted limpet and rubber washers complete with all accessories as required, as per the direction of Engineer-in-Charge, as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing ridges or hips 60cm (Sixty centimetres) overall width and 0.45mm (Zero decimal forty five milimetre) thick prepainted steel sheet ISI marked ridges (factory made) of TATA/SAIL/Reliance /Jindal steel shall be having proper Gola/shape of steel sheet with hot dipped metalic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (twenty) microns over 5 (five) microns primer coating of back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted J or L hooks, bolts and nuts 6mm (Six milimetre) dia with prepainted G.I. limpet and bitumen washer complete with all accessories as required, as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing valley 90cm (Ninety centimetre) overall width and 0.60mm (Zero decimal six zero milimetres) thick prepainted steel sheet hot dipped metallic zinc coated sheet ISI marked of TATA/ SAIL/Reliance/Jindal steel with top coat of regular modified polyester (RMP) organic coated of 20 (twenty) microns over 5 (Five) micron primer coating to back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six milimetre) with prepaintred limpet and bitumen washers complete with all accessories as required, as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 15cm (Fifteen centimetre) wide and 45cm (Forty five centimetre) deep 0.80mm (Zero point eight zero milimetre) thick Plain Galvanised Iron sheet gutter TATA/ SHAKTI with iron brackets 40x3mm (Forty into Three milimetre) size bolts, nuts and washers etc. including making necessary connections with rain water pipe complete, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 6mm (Six milimetre) thick plain asbestos cement sheet ceiling of approved quality with butt jointing and wood screws (frame work and cover fillets to be measured and paid for separately), as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providng and Fixing Mild Steel Black Plain Sheet 2mm (Two milimetre) thick in eaves board/ facia/soffits/ceiling including cuttng, fixing and welding to steel roof members and applying a coat of red lead primer complete (base members of steel work shall be measured & paid separately), as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Painting steel work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture and as per the direction of Engineer-in-Charge including carriage of material within all leads and lifts and other incidental. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing and laying cement concrete flooring 1;2:4 (One Cement isto Two sand: isto Four graded sone aggregate 20mm (Twenty milimetre) in nominal size) laid in one layer finished with a floating coat of neat cement 40mm (Forty milimetre) thick and as per the direction of Engineer-in-Charge including carriage of material within all leads and lifts and other incidental. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing and laying cement concrete 1:2:4 (one cement isto two sand isto four graded stone aggregate 20mm (Twenty milimetre) nominal size. Laid in one layer finished with a floating coat of neat cement 40mm (Forty milimetre) thick flooring including carriage of material within all leads and lifts and other incidentials. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing and filling brick bats in soakpit and as per the direction of Engineer-in-Charge including carriage of material within all leads and lifts and other incidental. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing and fixng Vitreous china wash down water closet European type W.C. Pan seat No.20087 (Twenty thousand eighty seven) of Hindware/Cera/Jaquar of Star shite/Snow white shade and its equivalent with integral P or S trap including joisting the trap with soil pipe in cement mortar 1:1 (One Cement isto One Sand) (Earth work, bed concrete, foot rest and trap measured and paid for separately) Indian Universal closet, as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing flat back 550x400mm (Five hundred fifty into Four hundred milimetre) vitreous china wash basin with single hole for pillar trap of Garnat No.10010 with under counter of Cera/Jaquar or Star/Snow white Hindware with C.I. or M.S. bracketsw painted white including cutting hloles and making good the same but excluding fittings, as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two milimetre) dia PVC waste pipe of Hindware/Cera/ Jaquar, as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing G.I. inlet connection for flush with WC pan , as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 600x20mm Stainnless steel Towel rail of Continental series of Jaquar/ Classic series of Hindware/Floral series of Cera I.S. marked complee with C.P. brass brackets fixed in wooden plugs with chromium plated brass screws, as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing flat back 600x450mm (Six hundred into four hundred fifty milimetre) beveled edge mirror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. brass screwsw and washers, as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing C.P. brass full way valve with wheel of continental series of Jaquar/ Classic series of Hindware/ Floral series of Cera 25mm (Twenty five milimetre) nominal bore, as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing C.P. brass full way valve with wheel of continental series of Jaquar/ Classic series of Hindware/ Floral series of Cera 32mm (Thirty two milimetre) nominal bore, as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 15mm dia (Fifteen milimetre) diametre C.P. Brass angle valve for basin mixer and geyser points of approved quality confirming to IS:8931 of continental series of Jaquar/ Classic series of Hindware/ Floral series of Cera, as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 15mm dia (Fifteen milimetre) diametre C.P. Brass Bib cock of continental series of Jaquar/ Classic series of Hindware/ Floral series of Cera, as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen milimetre) dia C.P. brass stop cock, as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen milimetre) nominal bore P.V.C. connection pipe with brass union 45cm length complete, as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing chorimum plated brass soap dish with C.P. brass brackets of continental series of Jaquar/ Classic series of Hindware/ Floral series of Cera fixed to wooden cleats with C.P. brass screws, including carriage of materials within all leads, lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing bath shower of continental series of Jaquar/ Classic series of Hindware/ Floral series of Cera, as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing drainage board or continental series of Jaquar/ Classic series of Hindware/ Floral series of Cera with C.I. Brackets inclding painting of brackets, cutting and making good the walls wherever required white glazed fire clay draining board of sizevitreopus china 600x450x25mm (Six hundred into Four hundred fifty into Twenty five milimetre) size, as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is inclusive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen milimetre) nominal outer dia pipes Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is inclusive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 20mm Twenty milimetre) nominal outer dia pipes Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is inclusive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 25mm Twenty five milimetre) nominal outer dia pipes Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is inclusive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing water tank make P.V.C. (Poly Venyl Chloride) SINTEX with tripple layer having capacity of 1000 litres (One thousand) litres each tank ISI 12701 (Twelve thousand seven hundred one) G.I. (Galvanised Iron) necessary fittings including over flow pipe scour pipe etectera for inlet and outlet and inside connection 15mm (Fifteen milimetre) nominal bore ball valve and P.V.C. (Poly Venyl Chloride) cover with locking arrangements including placing with all height above ground level complete in all respect as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is inclusive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and Dora size 470x420mm (Four hundred seventy into Four hundred twenty milimetre) with bowl depth 178mm (One hundred seventy eight milimetre) of Cera or its equivalent stainless steel Kitchen sink with drain boarfd and C.I. or M.S. bracket painted white including cutting holes in walls and making good the same but excluding the cost of fitting, as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred milimetre) diametre Type-B conforming to BIS-13592-92 in trenches P.V.C. Supreme or equivalent pipe soil, waste and ventilating pipes fixing with adhesive mixture complete 8/4.6mm (Eight/Four point six milimetre) thick of supreme or its equivalent including entire carriage of material within all leads, lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five milimetre) diametre Type-B conforming to BIS-13592-92 in trenches P.V.C. Supreme or equivalent pipe soil, waste and ventilating pipes fixing with adhesive mixture complete 8/4.6mm (Eight/Four point six milimetre) thick of supreme or its equivalent including entire carriage of material within all leads, lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred milimetre) (Confirming to ISI No.14735-99 PVC Supreme/ Kishan/ Astral or equivalent plain bend including filling the joints with approved adhesive complete, as per specification, approved drawing, design as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate inclusive of octroi, royality, malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five milimetre) (Confirming to ISI No.14735-99 PVC Supreme/ Kishan/ Astral or equivalent plain bend including filling the joints with approved adhesive complete, as per specification, approved drawing, design as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate inclusive of octroi, royality, malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing single equal branch of required P.V.C. Supreme/ Kishan/ Astral or equivalent plain bend 100mm (One hundred milimetre) nominal size, as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any othr taxes imposed by the Government.

Providing and fixing single equal branch of required P.V.C.Supreme/ Kishan/ Astral or equivalent plain bend 75mm (Seventy five milimetre) nominal size, as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any othr taxes imposed by the Government.

Providing and fixing 100mm (One hundred milimetre) diametres PVC Supreme/Kishan/ Astral or equivalent Collar complete as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any othr taxes imposed by the Government..

Providing and fixing 75mm (Seventy five milimetre) diametres PVC Supreme/Kishan/ Astral or equivalent Collar complete as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any othr taxes imposed by the Government..

Providing and fixing 100mm (One hundred milimetre) nominal size/diameter PVC clamps for PVC pipe, as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Constructing manhole with RCC (reinforced cementconcrete) top slab in 1:2:4 mix in (One Cement: Two Sand: Four graded crushed stone aggregate 20mm (Twenty milimetre) nominal size), foundation concrete 1:4:8 (One Cement: Four Sand: eight graded crushed stone aggregate 40mm (Forty milimetre) nominal size, inside plastering 15mm (Fifteen milimetre) thick with cement mortar 1:3 (One Cement: Three Sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix ((One Cement: Two Sand: Four graded crushed stone aggregate 20mm (Twenty milimetre) nominal size) finished smooth complete including curing and testing Inside size 800mmx800mm (Eight hundred milimetre into Eight hundred milimetre) and 500mm (Five hundred milimetre) deep including C.I. (Cast Iron) cover with frame, (Light duty single seal pattern –I) 455mmx610mm (Four hundred fifty five into Six hundred ten milimetre) internal dimensions total weight of cover and frame to be not less than 38 kg (Thirty eight kilogram) (weight of cover 23kg (Twenty three kilogram) and weight of frame 15kg (Ffteen kilogram) with 300mm (Three hundrede milimetre) thick walls of squared rubble masonry coursed with hard stones of approved quality in cement mortar 1:3 (One Cement: Three Sand), as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Constructing manhole with RCC (reinforced cement concrete) top slab in 1:2:4 mix (One Cement: Two Sand: Four graded crushed stone aggregate 20mm (Twenty milimetre) nominal size), foundation concrete 1:4:8 (One Cement: Four Sand: eight graded crushed stone aggregate 40mm (Forty milimetre) nominal size), inside plastering 15mm (Fifteen milimetre) thick with cement mortar 1:3 (One Cement: Three Sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix ((One Cement: Two Sand: Four graded crushed stone aggregate 20mm (Twenty milimetre) nominal size) finished smooth complete including curing and testing Inside size 800mmx800mm (Eight hundred milimetre into Eight hundred milimetre) and 1000mm (One thousand milimetre) deep including C.I. (Cast Iron) cover with frame, (Light duty single seal pattern –I) 455mmx610mm (Four hundred fifty five milimetre into Six hundred ten milimetre) internal dimensions total weight of cover and frame to be not less than 38 kg (Thirty eight kilogram) (weight of cover 23kg (Twenty three kilogram) and weight of frame 15kg (Ffteen kilogram) with 300mm (Three hundrede milimetre) thick walls of squared rubble masonry coursed with hard stones of approved quality in cement mortar 1:3 (One Cement: Three Sand), as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm dia (One hundred milimetre) diametres C.P. (Chromium Plated) Grating of Paryag/ Hindware/ Cera for gully floor or Nahni trap as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred milimetre) dia on wall face PVC (D-Plast) rain water pipe finolex/ Rel pipe (Reliance/Vectus or its equivalent of working pressure not less than 4.50 kg/per sqm including filling the joints with approved adhesive complete, as per specification, approved drawing, design as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leasds, lifts and other incidentals. The rate inclusive of octroi, royality, malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 20mm (Twenty milimetre) dia Peet valve without nut and pipe, as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 15 cm(Fifteen centimetre) wide, 45 cm (Forty five centimetre) overall semi- circular plain G.S. sheet gutter with iron brackets 40x3mm (Forty into Three milimetre) size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete 0.80 mm Zero point Eight Zero milimetre) thick with zinc coating not less than 275 gm/m² as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Supplying and fixing C.I. cover without frame for manholes 560 mm (Five hundred sixty milimetre) diameter C.I. cover (heavy duty) the weight of the cover to be not less than 108 kg. (One hundred eight kilogram) as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred milimetre) dia PVC cowl as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Supplying C.I cover light duty rectangular 455x610 mm (Four hundred fifty five into Six hundred ten milimetre) with frame weight 38 kg (single seat) as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Providing and fixjng I (One ) H.P. Induction motor including feet valve complete as per specification, approved drawing design as per entire satisfaction and direction of the Engineer-in-Charge within all leads and lifts and other incidentals. The rate is incluisive of octroi, royality, malkana toll tax, GST or any other taxes imposed by the Government.

Ashok Soni