Supply, Installation, Testing and Commissioning of Furniture and Internal Fit-outs works at JNV West Tripura (Tripura)

Bill of Quantities

Name of the Item Items Sample Image Quantity Unit (including 18% Amount

(A) SCHOOL BUILDING

Supply & installation Big Desk (for two persons)-The overall dimensions of desk will be 1066mm * 930mm *

Height 760mm, complete as per Specifications enclosed and direction of Engineer-in- charge having the Table

top shall be made up of 18.0 mm thick plywood IS 303 of MR Grade OSL (one side shall be laminated, and other

side shall have balancer finish). Table top dimensions shall be W 850 mm x D 380 mm. Edge towards bench

shall be post formed with round edge. The remaining three edges must be sealed with 2mmthick PVC edge

banding tape. Edge band must be trimmed on edges and corners. The desk shall be Greenguard certified for

low chemical emission of VOCs (Voltage Organic Compounds) and carcinogens, contributing to a healthier room

environment. Valid certificate to be submitted along with the bid. Make of Plywood : Merino / Greenply / Century /

Kitply. Make of Laminate & balancer : Marino / Greenlam / ASIS / Century following specifications. Seat and back

rest shall be made of 18mm thick plywood of MR Grade OSL (one side shall be laminated, and other side shall

have balancer finish) except back rest. Back rest shall be have both sides colour lamination.Technical details of

seat and back rest are mentioned below:Seating bench dimensions shall L 900 mm x W 300 mm. Front side

shall be rounded with post forming. Remaining three edges shall sealed with 2mm thick PVC edge banding tape.

Back rest dimensions shall L 900 x H 200 mm Upper side shall be rounded with post forming Remaining three

edges shall be sealed with 2mm thick PVC edge banding tape. Desk Shelve shall be made of prime quality

0.8mm thick CRCA sheet of H150mmxD300mm and side stiffeners of MS CRCA tube size

19mmx19mmx1mmthick. One vertical support (partition) of square tube size 25mm square x1.2mm thick must

be provided at centre of tray . Upper moedsty made of prime quality 0.8mm thick CRCA Sheet Powder Coated Classroom

1 should be embossed with dimples in round shape, height will be 150mm, there should be Perforated lower Desk Big 120 Each 8910.00 1069200.00

modesty Made of prime quality 0.8 mm thick CRCA sheet of size H150mmXD21mm with square perforation,

CRCAT ube of size 19x19x1mm thick to be inserted for full length at bottom of Jali . Bag hook should be provide

on both side of piller made of minimum 4mm dia rod Side frame structure:- Made of prime quality CRCA pressed

form section 165mmx25mmx1mm thick welded to 25mmx50mmx1.2mm thick CRCA tube , Seat and back side

frame structure made of prime quality CRCA pressed form section 165mmx25mmx1mm thick welded to 25.4mm

diameter x 1.6mm thick ERW-1pipe , there will be 8no. horizontal supports are 25mmx25mmx1.2mm thick CRCA

pipes. . Bottom Rectangular tube 50x25x 1.2mm thick should be closed with PPCP cap bothside sand pipe dia.

25.4x1.6mm thick should be closed with metal (Backside) and other side (Undertheseat) PPCP cap, complete as

per engineer incharge Desk should be in semi knock down form with the help 16 connecting pipes ; 8 pipes on

each side : connecting pipe size will be 20x20x1.2mm .All Metal Pieces Shall Be Welded Properly Strongly and

conformity with regulations with CO2 Welding Shall Be Used , CRCA Metal Shall Be Coated After Being Treated

With At Least Three Stages And Cleaned From Oil , Grease , Dust And Other Dirt Using Special Thermal Control

Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² ,

Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With

Suitable Temperature And Time For The Process , Metal Pipe & 7 tank treatment with minimum 45-50 micron

powder coating .

Digitally signed by DAIPAYAN

Name of the Item Items Sample Image Quantity Unit (including 18% Amount

Supply & installation Medium Desk (for two persons)-The overall dimensions of desk will be 900mm W± 5 X

890mm D± 5 X 688/420mm H± 5 , complete as per Specifications enclosed and direction of Engineer-in- charge

having the Table top shall be made up of 18.0 mm thick plywood IS 303 of MR Grade OSL (one side shall be

laminated, and other side shall have balancer finish). Table top dimensions shall be W 850 mm x D 380 mm.

Edge towards bench shall be post formed with round edge. The remaining three edges must be sealed with

2mmthick PVC edge banding tape. Edge band must be trimmed on edges and corners. The desk shall be

Greenguard certified for low chemical emission of VOCs (Voltage Organic Compounds) and carcinogens,

contributing to a healthier room environment. Valid certificate to be submitted along with the bid. Make of

Plywood : Merino / Greenply / Century / Kitply. Make of Laminate & balancer : Marino / Greenlam / ASIS /

Century following specifications. Seat and back rest shall be made of 18mm thick plywood of MR Grade OSL

(one side shall be laminated, and other side shall have balancer finish) except back rest. Back rest shall be have

both sides colour lamination.Technical details of seat and back rest are mentioned below:Seating bench

dimensions shall L 900 mm x W 300 mm. Front side shall be rounded with post forming. Remaining three edges

2 shall sealed with 2mm thick PVC edge banding tape. Back rest dimensions shall L 900 x H 200 mm Upper side

shall be rounded with post forming Remaining three edges shall be sealed with 2mm thick PVC edge banding

tape. Desk Shelve shall be made of prime quality 0.8mm thick CRCA sheet of H150mmxD300mm and side

stiffeners of MS CRCA tube size 19mmx19mmx1mmthick. One vertical support (partition) of square tube size Classroom

25mm square x1.2mm thick must be provided at centre of tray . Upper moedsty made of prime quality 0.8mm Desk

thick CRCA Sheet Powder Coated should be embossed with dimples in round shape, height will be 150mm, 120 Each 8750.00 1050000.00

there should be Perforated lower modesty Made of prime quality 0.8 mm thick CRCA sheet of size Size

H150mmXD21mm with square perforation, CRCAT ube of size 19x19x1mm thick to be inserted for full length at

bottom of Jali . Bag hook should be provide on both side of piller made of minimum 4mm dia rod Side frame

structure:- Made of prime quality CRCA pressed form section 165mmx25mmx1mm thick welded to

25mmx50mmx1.2mm thick CRCA tube , Seat and back side frame structure made of prime quality CRCA

pressed form section 165mmx25mmx1mm thick welded to 25.4mm diameter x 1.6mm thick ERW-1pipe , there

will be 8no. horizontal supports are 25mmx25mmx1.2mm thick CRCA pipes. . Bottom Rectangular tube 50x25x

1.2mm thick should be closed with PPCP cap bothside sand pipe dia. 25.4x1.6mm thick should be closed with

metal (Backside) and other side (Undertheseat) PPCP cap, complete as per engineer incharge Desk should be

in semi knock down form with the help 16 connecting pipes ; 8 pipes on each side : connecting pipe size will be

20x20x1.2mm .All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations with CO2

Welding Shall Be Used , CRCA Metal Shall Be Coated After Being Treated With At Least Three Stages And

Cleaned From Oil , Grease , Dust And Other Dirt Using Special Thermal Control Coating For Metal Furniture To

Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² , Automatic Spray Coating Shall Be

Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For

The Process , Metal Pipe & 7 tank treatment with minimum 45-50 micron powder coating .

(iii)TEACHER TABLE :Supplying and installation of knock down type Office Table made of Pre-laminated MDF

board with decorative lamination on one side and balancing lamination on other side top of size 1200 X 600 X

750 mm. Worktop shall be rounded in all four corners and should have an overhung of 50mm alongwith one

drawer unit made of 0.5mm thick CRCA Steel sheet. The table top shall be supported over legs consists of 4

Powdered coated MS legs with connected beams with pipe size 25x25x1.2 mm thick. Teacher

Digitally signed by DAIPAYAN

Name of the Item Items Sample Image Quantity Unit (including 18% Amount

(v) TEACHER BOARD [Excluding cost of Interactive Flat-Panel Display (IFPD)]

Technical Specification for Smart Board with Double-Track Sliding System for Green and White Boards

fitted in an Anodised Aluminium Frame with concealed cable management and provision for mounting of

Digital Screen:

Supply, installation, testing, commissioning (SITC) of an integrated digital teaching–learning solution comprising:

(a) Anodised Aluminium Frame, double track sliding system for white & green board and provision for mounting

of digital screen with concealed cable management,

(b) Vitrified magnetic ceramic-steel Green Board and White Board panels.

•Dimensions and Configuration: Total Width of the Setup is ~12 feet and height ~4.0 feet from the board surface

(excluding the width of aluminium frame).

• Material: Providing and fixing anodised aluminium (alloy 6063-T6) framed sliding system for smart board

with minimum 2.0 mm thick extruded sections, anodised to AA1 grade as per IS 1868, mounted on a heavy-

duty top-hung aluminium track (min. 2.5 mm thick) with sealed ball-bearing nylon/PU rollers (load capacity not

less than 120 kg per panel), concealed bottom guide, EPDM gaskets, SS-304 fasteners, pelmet/valance cover,

and soft end-stops/soft-close mechanism, including all brackets, fixings, alignment, cable provisions,

commissioning, and making good complete as per drawings and Engineer-in-Charge. taecher

•Design: One slot to fix IFPD, other slot for Green & White boards sliding on double track system with Locking board

facility on sliding frame to keep the IFPD display safe.

•Top & Bottom Rails: Tracks shall be aligned and reinforced to ensure boards move easily and without wobble.

• Back Side: The backside of the smart board, to concealed the wall surface, provided & fixed with 18 mm thick

HDHMR board laminated (white coloured matte finish) with 0. mm, edges sealed with 1 mm PVC edge banding,

fixed to the anodised aluminium frame with concealed screws/rivets, with ventilation slots as required, and shall

be moisture, termite and borer resistant.

•Load Capacity: Safe to hold IFPD + white & Green boards with ≥1.5× safety factor.

•Cable Management: Built-in channels for power, LAN, HDMI, USB.

•Safety: Rounded edges, tamper-resistant covers, concealed fixing.

•Finish: Durable, corrosion-resistant coating suitable for indoor use.

•Additional Requirements: (a) All boards and the structure must be securely fixed to the wall with appropriate

(b) Provision for cable management must be included for the IFPD (i.e., concealed conduit/path for power and

c) The unit must be free from sharp edges, splinters, or any protruding parts that could cause injury.

(d) Installation height should ensure comfortable writing access for average adult and student height (typically

bottom edge ~2.5 to 3 feet from the floor).

(b) Vitrified magnetic ceramic-steel Green Board and White Board panels:

•Function: Boards shall slide horizontally on a top and bottom aluminium/steel channel track to fully cover or

reveal the IFP as needed.

4 •Material: Vitrified ceramic-steel, magnetic, double-coated. 18 Each 62100.00 1117800.00

•Sliding Boards: Quantity: 1 no. Green board & 1 no. White board.

•Green Board Surface: Matte, chalk-friendly, stain/scratch resistant.

•White Board Surface: Glossy surface, Dry-erase marker friendly, ghost-free, easy clean.

•Size: ~6 feet (W) × 4 feet (H) (Each Board) with thickness 8mm.

•Frame: Anodised aluminium, rounded edges, concealed fasteners.Note - Dimensions mentioned are indicative.

Actual may vary as per site requirements

(B) PRINCIPAL AND VICE-PRINCIPAL ROOM

Digitally signed by DAIPAYAN

Name of the Item Items Sample Image Quantity Unit (including 18% Amount

TABLE: Supplying and installation of site knock down type Office Table as per approved design and directrion of

Engineer-in-charge. Work Top - Work top shall be made 25mm thick Pre-laminated MDF board with

decorative lamination on one side and balancing lamination on other side confirming to IS 12406:2003 with

post forming on front, back and machine pressed PVC egde banding 2mm thick glued with industrial adhesive

and diffused with board monolithically on other two sides. Table top shall have 75mm overhung on front and

25mm overhung on sides. Understructure- C-type leg shall be made of tubular section of 50mm x 50mm x

1.6mm (wall thickness) thick vertical member and 40mm x40mm x1.6mm (wall thickness) Horizontal M.S.

pipe confirming IS-Grade 4932 shall be finished with epoxy polyster powder coated DFT 50-60 Micron. The

legs shall be fitted to the ground with M8 screw leveler with the height adjustment up to 15mm. The

cross members shall be mounted by end brackets made of 3mm thick CRCA steel sheet confirming IS

513: 2008 and finished with epoxy polyster powder coated DFT 50-60 Micron confirming IS 13871:1993.

Wire management - Electrical wires shall be carried from horizintal/ vertical duct made of 0.7mm CRCA

steel sheet confirming to IS 513:2008. The switch plate or grommet depending upon requirement shall also be

provided for electrical/LAN connection on table top. Modesty Panel -Modesty Panel of height 450mm shall be

made of 1.5mm thick CRCA sheet sheet confirming to IS 513: 2008 and shall be finised with epoxy polyster

powder coated DFT 50-60micron. Storage body- Storage top shall also be made of 25mm thick Pre-lam MDF

board confirming to IS 12406:2003 with post forming on two sides and machine pressed PVC egde banding 2

mm thick glued with industrial adhesive and diffused with board monolithically on other two sides. The body of

storage units shall be made of 0.8mm thick CRCA steel Sheet and skirting shall be of 1.2mm thick CRCA steel

sheet confirming to IS 513: 2008 finished with epoxy powder coated of DFT 50-60 Micron confirming IS

13871:1993. Internal Shelves shall be also made up of 0.8mm CRCA steel sheet confirming to IS 513: 2008 and

shall be mounted with the Metal shelf support pin made of 2mm thick CRCA Steel sheet with Nickel or Chrome

plating. M10 screw leveler is given with height adjustment up to 12mm to 15mm.

Digitally signed by DAIPAYAN

Name of the Item Items Sample Image Quantity Unit (including 18% Amount

(i) PRINCIPAL ROOM TABLE

5 Table of Size 1800mm (W) x 900mm (D) x 750mm (H) with Side Storage of Size 900mm (W) x 450mm (W) X 1 EACH 63000.00 63000.00

750mm (H) and Back Storage 1800mm (W) x 450mm (D) x 750mm (H) as per specifications above

(ii) VICE-PRINCIPAL ROOM TABLE VICE

6 Table of Size 1650mm (W) x 900mm (D) x 750mm (H) with Side Storage of Size 900mm (W) x 450mm (W) X PRINCIPA 1 each 58000.00 58000.00

750mm (H) and Back Storage 1650 mm (W) x 450mm (D) x 750mm (H) as per specifications above. L

(iii) PRINCIPAL ROOM CHAIR

High Back Revolving Chair, Overall Dimension:- 700W ±10 x 700D ±10 x 1210H ±10 mm,Seat of Medium back

chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on

Seat,Used PU Moulded foam on Seat of D-45 kg/m3 , Back of chair is made of Injection moulded PP material

structure upholstered with Mesh fabric , Adjustable Lumber support upholstered with fabric , Adjustable

Headrest on back Upholstered with Mesh Fabric ,Seat Size:- 470W ±10 x 460D ±10 x 70Thick. ±5 mm ,

Back Size: 500W ±10 x 780H ±10,Mechanism:- The Synchro tilt Mechanism ,Used gaslift of 90 mm size PRINCIPA 1 each 5000.00 5000.00

of Class-IV grade,Armrest:- PU padded adjustable armrest fixed with Seat ,Chair Base & Wheels: SS 202 L CHAIR

Polished finish Plated base consists of 5 prongs with 640±5 mm pitch circle diameter, 50mm Dia. Black

Nylon - Twin Wheel Pin castor .

Visitor Chair for Principal, Overall Dimension:- W600±10 x 600D ±10 x 890H ±10 mm,Seat of Medium back

Visitor chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric

upholstery on Seat , Used PU Moulded foam on Seat of D-45 kg/m3, Back of Medium back chair is

made of Injection moulded PP material structure with Mesh fabric, Seat Size:- 460W ±10 x 470D

±10 x 60Thick. ±5 mm , Back Size:- 440W ±10 x 470H ±10,Armrest:- Fixed PP armrest ,Understructure:-

Cantilever frame made SS Polished Finish round pipe with Plastic bushes . Frame Material -SS 202 Polished

Digitally signed by DAIPAYAN

Name of the Item Items Sample Image Quantity Unit (including 18% Amount

(v) VICE-PRINCIPAL ROOM CHAIR

High Back Revolving Chair, Overall Dimension:- 700W ±10 x 700D ±10 x 1210H ±10 mm,Seat of Medium back

chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on

Seat,Used PU Moulded foam on Seat of D-45 kg/m3 , Back of chair is made of Injection moulded PP material

structure upholstered with Mesh fabric , Adjustable Lumber support upholstered with fabric , Adjustable

Headrest on back Upholstered with Mesh Fabric ,Seat Size:- 470W ±10 x 460D ±10 x 70Thick. ±5 mm ,

Back Size: 500W ±10 x 780H ±10,Mechanism:- The Synchro tilt Mechanism ,Used gaslift of 90 mm size

of Class-IV grade, Armrest:- PU padded adjustable armrest fixed with Seat ,Chair Base & Wheels: SS 202

Polished Finish base consists of 5 prongs with 640±5 mm pitch circle diameter, 50mm Dia. Black Nylon - Twin

9 PRINCIPA 1 each 5000.00 5000.00

Wheel Pin castor .

Visitor Chair for vice principal, Overall Dimension:- W600±10 x 600D ±10 x 890H ±10 mm,Seat of Medium back

Visitor chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric

upholstery on Seat , Used PU Moulded foam on Seat of D-45 kg/m3, Back of Medium back chair is

made of Injection moulded PP material structure with Mesh fabric, Seat Size:- 460W ±10 x 470D

±10 x 60Thick. ±5 mm , Back Size:- 440W ±10 x 470H ±10,Armrest:- Fixed PP armrest ,Understructure:-

Cantilever frame made SS Polished Finish round pipe with Plastic bushes . Frame Material -SS 202 Polished

Digitally signed by DAIPAYAN

Name of the Item Items Sample Image Quantity Unit (including 18% Amount

(i) TABLE (SEATING CAPACITY AS PER ACTUAL REQUIREMENT)

Supplying and installation of a modular, knock-down center island table sized approximately 3600 mm in length

(adjustable to actual requirements) by 1350 mm in width and 750 mm in height, constructed from high-quality 25

mm thick commercial grade plywood or BWR (Boiling Water Resistant) grade plywood with decorative

lamination on visible faces and balanced lamination beneath for enhanced strength and moisture resistance. All

edges are sealed with 2 mm thick machine-pressed PVC edge banding bonded with industrial adhesive to

ensure a seamless, monolithic appearance. The gable ends are fabricated of the same 25 mm thick commercial

grade plywood with decorative lamination on both sides and matching edge banding for consistent aesthetics

and superior durability. Modesty 18mm matching laminate. The table shall have an underbody vertical support

panel running continuously along its length to enhance stability and strength. The understructure uses precision-

cut, laminated plywood panels assembled with knock-down fittings for ease of installation and future

reconfiguration, ensuring superior load-bearing capacity and long-term durability. A concealed wire management

system beneath the worktop integrates pre- laminated plywood cable trays or high-quality plastic trays fixed STAFFRO

11 with durable brackets, complete with provisions for switch plates and grommets to facilitate safe, OM 8.00 Rmt 10000.00 80000.00

organized routing of electrical and data cables. All surfaces are finished for scratch and stain resistance with anti- TABLE

fungal and moisture-resistant properties, and installation will follow best woodworking practices, with final

dimensions and seating capacity determined by the actual site layout.

(ii) WORK SPACE WITH IN-BUILT LOCKABLE OVERHEAD STORAGE SPACE FOR STAFFROOM (AS PER

ACTUAL REQUIREMENT)

Supplying and installation of site knock-down type modular wall-mounted workspace unit of approximate

size 900W x 600D x 750H mm (for one staff), including working counter and lockable overhead storage

cabinet of 900W x 450D x 650H mm. The structure shall be made of 18 mm thick BWP grade plywood with

decorative laminate on external surfaces and balancing laminate on inner faces conforming to IS:303/IS:12406.

All exposed edges shall be sealed with 2 mm PVC edge banding. The worktop shall be 25 mm thick Laminated

Plywood board with post-formed front edge and machine-pressed PVC edge banding, securely fixed to the

wall using concealed MS cleats and brackets. The overhead cabinet shall be fitted with soft-close

concealed hinges, SS handles, and magnetic catchers of approved make, with one adjustable shelf and

modular connectors for alignment and expansion to adjoining units.

Each workspace shall include provision for electrical connectivity with 6A/16A modular sockets (as per

requirement) positioned at approximately 450 mm above finished floor level for easy access. The worktop shall

12 have a circular cable hole (50–60 mm diameter) with grommet for laptop and equipment wiring. All wiring, 20.00 Rmt 18000.00 360000.00

sockets, and conduits shall be concealed neatly within the table body, routed through internal PVC raceways to

maintain a clean, clutter-free appearance. Junction boxes and ducts shall be integrated to provide safe,

organized cable management without visible wiring.

The entire unit shall be wall-mounted using heavy-duty MS brackets or suitable fasteners based on wall type,

finished neatly with matching silicone sealant at all joints. All fittings and hardware, including soft-close hinges

and handles, shall be of reputed make. The unit shall be termite-resistant, moisture-resistant, easy to maintain,

and made from ISI-marked prime quality boards. The overall layout and detailing shall match the approved

reference image, with actual dimensions finalized as per site requirements and direction of the Engineer-in-

Digitally signed by DAIPAYAN

Name of the Item Items Sample Image Quantity Unit (including 18% Amount

Chair for staffroom, Overall Dimension:- W600±10 x 600D ±10 x 890H ±10 mm,Seat of Medium back Visitor

chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery

on Seat , Used PU Moulded foam on Seat of D-45 kg/m3, Back of Medium back chair is made of

Injection moulded PP material structure with Mesh fabric, Seat Size:- 460W ±10 x 470D

±10 x 60Thick. ±5 mm , Back Size:- 440W ±10 x 470H ±10,Armrest:- Fixed PP armrest ,Understructure:-

Cantilever frame made SS Polished Finish round pipe with Plastic bushes . Frame Material -SS 202 Polished

(iv) PERSONAL LOCKER UNIT FOR STAFFROOM AND ONE EACH FOR PRINCIPAL AND VICE PRINCIPAL

Supplying and installation of Metal Lockers with Cam Lock one unit consiting of 380mm (W) x 450mm (D) x 1800

mm (H) with 4 Lockers.

Body-LH and RH Side and back panel is made up of 0.8mm thick CRCA steel sheet confirming to IS 513:2008.

Shelf hanging bracket is welded on both the side panel by spot welding. Shelf hanging bracket is made up of

0.8mm thick CRCA steel sheet confirming to IS 513:2008. front frame, top and bottom part made up 0.8mm thick

CRCA steel sheet confirming to IS 513:2008 and horizontal part is made up 0.8 mm thick CRCA Steel

sheet confirming to IS 513:2008. On a front frame horizontally provision is given at a common distance to PERSON

14 hold shutter bracket. Locker’s top is made up of 0.8mm thick CRCA Steel sheet confirming IS 513:2008 which is AL 2 each 8000.00 16000.00

having standard dimension 375 x378mm. Shelf is also made up of 0.8 mm CRCA Steel sheet confirming to IS LOCKER

Shutter- Is made up on 0.8mm thick CRCA Steel sheet confirming to IS 513:2008. All the shutter are hung on

shutter pin and shutter bracket, louvers are given in shutter for air flow. PVC flush handle and name plate is

used for handling and for name plate tagging. Standard locking arrangment is used for locking each shutter.

The bodies including shelves are given anti-rust surface treatment & are powder coated with epoxy polyester

powder coating of DFT 50- 60 Micron confirimg to IS 13871:1993.

(i) Supply and installation of Glass-door Storage of Size 915 mm (W) x 482mm (D) x 1980mm (H). It should

have shelf thickness of 0.8mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) with

clear glass of > 4.0 mm thick and all other components shall have a thickness of 0.8mm. These components

shall be made of CRCA steel sheet ‘D’ grade high yield strength as per IS 513:2008 The glass door storwel shall

have a SS handle and a Two-way locking mechanism with shooting bolt. It should have a height-wise adjustable LIBRARY

15 shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 BOOKSH 2 Per Unit 10000.00 20000.00

Screw type Leveller with Hex plastic base.All metal components would be epoxy polyster powder coated DFT 50- ELF

60 Micron confirimg to IS 13871:1993.

Wall mounted built in open book shelf - Overall Size 900WX300DX2100Hmm,Top made up of 18mm thick

Postlam plywood with PVC edge banding ,Side panel made up of 18mm thick Postlam plywood with PVC edge

bending , Skirting made up of 18mm thick Postlam plywood with PVC edge bending ,back panel made up of

18mm thick Postlam plywood , One number of drawer as per ref.image ,shelf made up of 18mm thick Postlam

plywood with PVC edge bending, all Wooden Panels Fix Joints With Minifix Dowels & other Fitting Equipment , One Side

All Wooden Panels Prime Quality Board With ISI Marked. Complete structure design should be as per reference book

Digitally signed by DAIPAYAN

Name of the Item Items Sample Image Quantity Unit (including 18% Amount

(i) TABLE (SEATING CAPACITY AS PER ACTUAL REQUIREMENT)

Supplying and installation of a modular, knock-down center island table sized approximately 3600 mm in length

(adjustable to actual requirements) by 1350 mm in width and 750 mm in height, constructed from high-quality 25

mm thick commercial grade plywood or BWR (Boiling Water Resistant) grade plywood with decorative

lamination on visible faces and balanced lamination beneath for enhanced strength and moisture resistance. All

edges are sealed with 2 mm thick machine-pressed PVC edge banding bonded with industrial adhesive to

ensure a seamless, monolithic appearance. The gable ends are fabricated of the same 25 mm thick commercial

grade plywood with decorative lamination on both sides and matching edge banding for consistent aesthetics

and superior durability. Modesty 18mm matching laminate. The table shall have an underbody vertical support

panel running continuously along its length to enhance stability and strength. The understructure uses precision-

cut, laminated plywood panels assembled with knock-down fittings for ease of installation and future

reconfiguration, ensuring superior load-bearing capacity and long-term durability. A concealed wire management

system beneath the worktop integrates pre- laminated plywood cable trays or high-quality plastic trays fixed

with durable brackets, complete with provisions for switch plates and grommets to facilitate safe,

organized routing of electrical and data cables. All surfaces are finished for scratch and stain resistance with anti-

fungal and moisture-resistant properties, and installation will follow best woodworking practices, with final

dimensions and seating capacity determined by the actual site layout.

(i) COMPUTER WORK STATION

Supplying and installation of knock down type Dual Computer Work Station of unit Size 1500mm (L) x 600m (W)

x 750mm (H) for two students

Work Top- Work top shall be made 25mm thick Laminated Plywood with decorative lamination on one side and

balancing lamination on other side confirming to IS 12823: 1990 with 2mm thick Machine pressed PVC

edge banding glued with industrial adhesive and monolithically diffused with board on all sides. COMPUT

18 Understructure supporting frame consist of laminated Plywood Gable ends of 18mm 30 rmt 8500.00 255000.00

Wire management-The Vertical /Electrical duct & Horizontal Cable tray ( wire carriers) are made of

CRCA steel sheet & fixed to the understructure below worktop with specially designed brackets. Provision

for fixing Switch plates are privided in the cable tray for easy access through wire mangaer or PVC grommet.

(ii) COMPUTER CHAIR FOR STUDENT

Medium Back Revolving Chair, Overall Dimension:- 700W ±10 x 700D ±10 x 1010H ±10 mm,Seat of Medium

back chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery

on Seat ,Used PU Moulded foam on Seat of D-45 kg/m3 , Back of chair is made of Injection moulded PP

material structure combination of upholstered with Mesh fabric , Seat and back connected through metal COMPUT

powder coated plate having Adjustable Lumber support upholstered with fabric , Seat Size:- 490W ±10 x 450D ER CHAIR

±10 x 70Thick. ±5 mm , Back Size: 525W ±10 x640H ±10,Mechanism:- The Synchro tilt Mechanism ,Using gaslift

of 90 mm size of Class 3 grade,Armrest: PU Padded Adjustable armrest,Chair Base & Wheels: Revolving

Pedestal SS 202 Polsihed Finish base consists of 5 prongs with 640±5 mm pitch circle diameter, 50mm Dia.

Black Nylon - Twin Wheel Pin castor .

i) Supply and installation of Glass-door Storage of Size 915 mm (W) x 482mm (D) x 1980mm (H). It should have

shelf thickness of 0.8mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) with clear

glass of > 4.0 mm thick and all other components shall have a thickness of 0.8mm. These components shall be

made of CRCA steel sheet ‘D’ grade high yield strength as per IS 513:2008 The glass door storwel shall have a LAB

SS handle and a Two-way locking mechanism with shooting bolt. It should have a height-wise adjustable shelf ALMIRAH

mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10

Screw type Leveller with Hex plastic base.All metal components would be epoxy polyster powder coated DFT 50-

60 Micron confirimg to IS 13871:1993.

(i) PHYSICS LAB

Digitally signed by DAIPAYAN

Name of the Item Items Sample Image Quantity Unit (including 18% Amount

Supply and installation of Lab Stool Seat Revolving Stool with Backrest Overall Dimension: 410W ±10 x 410D

±10 x 820H ±10 mm,Seat of chair is made of 12mm thick hot pressed Plywood pasted with High Density

PU foam & Leatherette upholstery, Back is made of 12mm thick hot pressed Plywood pasted with PU

foam D -40 kg/m3

, H-20 Seat and back fixed through metal powder coated Spine covered with plastic cover, Seat Size:

400W ±10 x 400D ±10 x 75Thick. ±5 mm, Back Size: 450W ±10 x 240H ±10 x 50Thick. ±5mm, Ground to seat

height-440-560mm, Mechanism:- Machanism Design With Features Of Revolving At 360 Degree. Machanism LAB

Provided Upright Position Locking, Seating Height Can Be Adjusted With a Pneumatic Gas Lift,Gaslift: Lift - STOOL

Used gaslift of 90 mm size of Class- IV grade with plastic bellow cover,

Chair Base & Wheels: Chair Base Made of polished finished SS 202 grade stainless steel, base consists of

polished finished SS 202 grade stainless steel 5 prongs with 560±5 mm pitch circle diameter, Polished finished

SS 202 grade stainless steel circular foot rest as per ref. image, 50mm Dia. Black Nylon - Twin Wheel Pin

KITCHEN & DINING

Dining Table: SS Dinning Table consists of Dinning Top is made up of 1 mm thickness Stainless steel sheet of

SS 304 Grade with overall dimension of 1800(L) X 700(D) X 750(H). The table top is reinforced with a 18 mm ply

Board on Stainless steel frame of square section 40mmx40mmx1.6mm. Dinning top of stainless steel sheet

shall be extended to the sides and a depth upto 40 mm under the table top in all directions including edge

rounding, grinding and finishing etc. all complete. The Table top shall finish in such a manner to avoid any sharp

edges. The table will be supported by four hollow legs made from SS 304 grade stainless steel. The hollow legs

shall be of square type of size 50mmx50mmx1.6mm. These legs shall be securely welded or mechanically DINING

22 fastened to the underside of the tabletop frame. For additional structural stability, stainless steel cross supports TABLE 80 Each 20000.00 1600000.00

shall be provided between the legs as shown in figure with 40mmx40mmx1.6mm SS square section. The

table shall include rubber shoes at the bottom of each leg to prevent floor damage and ensure stability. The

design shall prioritize user safety with no sharp corners or edges. The table must be structurally sound and

capable of supporting a uniformly distributed load of at least 250 kg. All materials used must conform to relevant

IS standards, and the finished product should be free from burrs, dents, or deformities

Dining Bench: The Bench shall be of size 1800 mm in length, 300 mm in depth, and 450 mm in height,

suitable for use in residential schools. The bench top shall be made of 18 mm thick plywood + Laminated ,

finished with a 0.8 mm thick decorative laminate on the top surface, and a balancing laminate backing on the

underside to ensure dimensional stability. All exposed edges shall be sealed with PVC edge banding or machine-

finished to prevent splinters and enhance durability. The plywood shall be scratch-resistant, water-resistant, and

easy to clean, with a light woodgrain or equivalent finish as approved. The supporting frame shall be fabricated

23 frame of square section 40mmx40mmx1.6mm MS Pipe in Powder Coated. These legs shall be securely BENCH 160 Each 5000.00 800000.00

welded or mechanically fastened to the underside of the benchtop frame. The bench shall include rubber shoes

at the bottom of each leg to prevent floor damage and ensure stability. The design shall prioritize user safety with

no sharp corners or edges. The bench must be structurally sound and capable of supporting a uniformly

distributed load of at least 250 kg. All materials used must conform to relevant IS standards, and the finished

product should be free from burrs, dents, or deformities

Digitally signed by DAIPAYAN