C/o Academiic Block, 25 bedded (Bunk Bed) Hostel, 01 type-II teacher qtrs, Kitchen cum dinning hall at Govt. IV School, Pilling Maling

SH: Academic block.

Excavation in decomposed or soft rock with or without blasting including disposal of the same lead upto 50 m and lift upto 1.50 m.

Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil and rock), lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m.

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) excluding the cost of centring and shuttering in :

b) Walls including attached buttresses, pilasters and their caps and bases and string courses etc.up to floor two level.

Centring and shuttering including strutting proping etc. and removal of form work for:

a) Foundation and plinth

b) Walls including attached buttresses, pilasters and their caps and bases and string courses etc.up to floor two level.

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in :

a) 1 : 1.50 : 3 (1 cement : 1.50coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.

a) 1 : 1.50 : 3 (1 cement : 1.50coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting proping etc. and removal of form work for:

Foundation Footings, Column, pillar and piers

plinth beams, beams, suspended floors, buttresses, pilasters and their caps and bases and string courses etc.up to floor two level.

Reinforcement of RCC work including bending, binding and placing in position complete.

a) Cold twisted bars.

Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand).

Extra for brick work with best available local bricks in superstructure above plinth level up to floor two level.

Half brick masonry (with best available local bricks) in cement mortar 1:3 (1 cement : 3 coarse sand) in foundation and plinth.

Extra for half brick masonry in superstructure above plinth level and up to floor two level.

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position.

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including aluminium butt hinges with necessary screws.

38mm thick best available local wood class - B I

Providing and fixing 38 mm thick wire gauge shutters using galvanized mild steel wire gauge of IS gauge designation 140G with wire of dia 0.56 mm for doors, windows and clerestory windows including anodized aluminum butt hinges with necessary screws.

a) Best available local wood class B-I

Providing and fixing, fly proof galvanized MS wire gauge of IS gauge designation 85 g with wire of dia 0.56 mm to windows and clerestory windows including 62 x 19 mm beading of best available local wood.

Providing and fixing 2.50 cm thick approved local wood eaves boards 23 cm wide with necessary mouldings etc.

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.

a) Ornamental grill.

Providing and fixing aluminum sliding door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete.

Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete.

Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete.

Providing and fixing MS Hooks and Eyes. A) 250 mm

Providing and fixing 40 x 3 mm flat iron hold fasts 40 cm long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm in 1 : 3 : 6 (1 cement : 3 sand : 6 hard stone chips 40 mm nominal size).

Providing and fixing MS fan clamp type I of 16 mm dia MS bar bent to shape with hooked ends in RCC slabs during lying including painting the exposed portion of loop all as per standard design complete.

Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement.

40 mm thick

Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses.

a) 0.63 mm thick GI sheet

Providing ridges or hips 60 cm overall in plain G.I. sheet fixed with galvanised iron J or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete.

a) 0.63 mm thick GI sheet

Providing and fixing 3 mm thick hard board sheet ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately).

Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling.

a) Best local approved quality wood.

Extra for making chamfered edges of beading.

15 mm cement plaster 1 : 4 (1 cement : 4 fine sand) on the rough side of single or half brick wall.

12 mm cement plaster 1 : 4 (1 cement : 4 fine sand).

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Applying priming coat with ready mixed primer of approved brand and manufacture on steel work.

White washing with whiting on new work (three or more coats) to give even shade.

Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats) to give an even shade.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade.

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar1 : 3 (1 cement : 3 fine sand) including shuttering complete.

Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work).

c) 25 mm nominal bore

Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work).

a) 15 mm nominal bore

Providing and fixing brass bib cock of approved quality.

a)15 mm nominal bore

Providing and fixing brass stop cock of approved quality.

a) 15 mm nominal bore

Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required.

b) Flat back wash basin size 550x400 mm with single 15 mm CP brass pillar taps of heavy quality.

Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.

b) Orissa type WC pan

Providing laying and jointing glazed stone ware pipe grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.

a) 100 mm dia SW pipes

Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design.

a) Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg).

Construction of soak pit 1.2 x 1.1 x 1.2 m filled with brick bats including SW drain pipe 100 mm dia and 1.20 m long complete as per standard design.

Add electrification 12.50%

Sh: 25 bedded (Bunk bed)

Earth work in excavation in foundation trenches not exceeding 1.50 m width or 10 Sq.m. on plan or drains not exceeding 1.50 m in width or 10 Sq.m. on plan including dressing of sides and ramming of bottoms, lift upto 1.50 m including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 coarse sand : 10 graded stone aggregate 20 mm nominal size) excluding the cost of centring an shuttering in:

a) Foundations and plinth

Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) excluding the cost of centring an shuttering in:

a) Foundations and plinth

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in :

a) 1 :1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.

a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.

a)1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in stair cases (excluding landing) except spiral cases including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface, preparing of the top surface and finishing, nosing upto floor two level but excluding the cost of centring, shuttering and reinforcement with 1 : 1.5 : 3 (1 cement :1.5 coarse sand :3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in chajjas exceeding 15mm in thickness upto floor two level including centring and shuttering complete but excluding the cost of reinforcement with 1 : 1.5 : 3( 1 cement: 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in shelves up to floor two level excluding cost of centering and shuttering and reinforcement with 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for :

a) Foundation, footings, bases of columns etc. and mass concrete.

c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

d) Lintels, beams, girders, bressumers and cantilevers etc.

f) Stairs (excluding landings) except spiral stair cases.

Reinforcement of RCC work including bending, binding and placing in position complete.

b) Tar/TMT steel

Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth.

Extra for half brick masonry in superstructure above plinth level and up to floor two level.

Random rubble masonry with hard stone in foundations and plinth in cement mortar 1 : 6 (1 cement : 6 fine sand) including levelling up with cement concrete 1 : 6 : 12 (1 cement : 6 coarse sand : 12 stone shingle 20 mm nominal size) at plinth level.

Masonry with pre-cast cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) blocks in cement mortar 1 : 4 (1 cement : 4 fine sand) in foundations and plinth.

Extra for pre-cast cement concrete block masonry in superstructure above plinth level up to floor two level.

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Providing and fixing 2.50 cm thick approved local wood eaves boards 23 cm wide with necessary mouldings etc.

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws. b) Ornamental Grill

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other section of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing /panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately) :

1.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868,Minimum anodic coating of grade SC 15)

Cement concrete flooring 1:2:4(1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement.

(a). 40 mm thick

40 mm thick red oxide flooring, under layer of 30 mm thick cement concrete 1 : 2 : 4 ( 1 cement : 2 coarse sand : 4 stone aggregate 12.5 mm nominal size ) & top layer of 10 mm thick plaster of cement red oxide mix ( using 3.5 kg of red oxide of iron per 50 kg of cement) 1 :3( 1 cement red oxide mix : 3 coarse sand ) finished with a floating coat of neat cement red oxide mix of same proportion.

Add per 1 kg for using more or less than 3.5 kg of red oxide of iron per 50 kg of cement in 40 mm thick red oxide flooring.

Red oxide plaster skirting (upto 30 cm height) with top layer of 6 mm thick plaster of cement red oxide mix ( using 3.5 kgs of red oxide of iron per 50 kg of cement ) in mortar 1 : 3 ( 1 cement : 3 coarse sand) finished with floating coat of cement red oxide mix of same proportion.

(a). 18 mm thick

Chequered terrazzo tiles 22 mm thick with marble chips of sizes upto 6mm in floors on 25 mm thick bed mortar 1 : 3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete:

a) Light shades using white cement

Providing and fixing on wall face C.I. rain water pipe including filling the joints with spun yarn soaked in neat cement slurry and cement mortar 1 : 2 ( 1 cement : 2 fine sand).

b) 100 mm diameter pipe

Providing and fixing M.S. Holder bat clamps of approved design of C.I. or S.C.I. pipes embedded in and including cement concrete block 10 cm x 10 cm x 10 cm of 1 : 2 : 4 mix (1 cement : 2 coarse sand: 4 stone aggregate 20mm nominal size) including cost of cutting holes and making good the wall etc.

b) 100 mm diameter

12 mm cement plaster 1 : 4 (1 cement : 3 fine sand).

15 mm cement plaster 1 : 6(1 cement : 6fine sand) on the rough side of single or half brick wall.

20 mm cement plaster 1 : 4 (1 cement : 4 fine sand).

Distempering (two or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade.

Painting two coats with oil type wood preservative of approved brand and manufacture on new work.

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade

Applying priming coat with ready mixed genuine red lead paint of approved brand and manufacture on steel work.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade

Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats) to give an even shade.

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

Providing and fixing 40 mm dia GI Pipe outlet in cement mortar 1 : 3 (1 cement : 3 fine sand) including cutting and making good the wall.

Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar1 : 3 (1 cement : 3 fine sand) including shuttering complete.

Providing laying and jointing glazed stone ware pipe grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.a) 100 mm dia SW pipes

Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design.

a) 100 mm dia SW pipes

Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work).

a) 15 mm nominal bore

Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work).

c) 25 mm nominal bore

Providing and fixing brass bib cock of approved quality.

a)15 mm nominal bore

Providing and fixing brass stop cock of approved quality.

a) 15 mm nominal bore

Providing and fixing PVC connection pipe with brass union.

1) 45 cm length

a) 15 mm nominal bore

Providing and fixing Sintex water tank.

Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.

b) Orissa Pattern WC Pan

Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required.

a) Flat back wash basin size 550x400 mm with single 15 mm CP brass pillar taps of heavy quality.

Providing and fixing kitchen sink including making all connection excluding cost of fittings. a) White glazed fire clay sink size 600x450x150 mm

Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.

Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality). a) 750 x 20 mm size

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.

a) 100 mm dia

Providing and fixing sand cast iron single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

a) 100 x 100 x 100 mm

Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design.

a) Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg).

Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honeycomb shaft and SW drain pipe 100 mmdia 1.80 m long complete as per standard design.

Add 12.50% Electrification

SH : SEPTIC TANK

Earth work in excavation in foundation trenches not exceeding 1.50 m width or 10 Sq.m. on plan or drains not exceeding 1.50 m in width or 10 Sq.m. on plan including dressing of sides and ramming of bottoms, lift upto 1.50 m including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

a) Ordinary Soil

Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Providing and laying cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) excluding the cost of centring and shuttering in :

a) Foundations and plinth

b) Walls including attached buttresses, pilasters and their caps and bases and string courses etc. up to floor two level.

Reinforced cement concrete in walls (any thickness) including attached pillasters, buttresses, plinth and string course, fillets etc from top of foundation up to floor two level including finishing and plastering the exposed surfaces with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface excluding cost of centring, shuttering and reinforcement in :

a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement of RCC work including bending, binding and placing in position complete.

b) Tar/TMT steel

Centring and shuttering including strutting proping etc. and removal of form work for:

b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

Providing laying and jointing glazed stone ware pipe grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.

a) 100 mm dia SW pipes

Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design.

a) 100 mm dia SW pipes

( Sh:- Type-II)

Excavation in decomposed or soft rock with or without blasting including disposal of the same lead upto 50 m and lift upto 1.50 m.

Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil and rock), lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m.

Providing and laying in foundations and plinth cement concrete 1 : 5 : 10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Centring and shuttering including strutting, propping etc and removal of form work for :-

a)Column, pillars, posts and struts etc.

b)Walls (any thickness) including attached pilasters,buttresses, plinth and string courses etc.

c)Lintels, beams, girders, bressumers and cantilevers etc.

d)Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

Reinforcement of RCC work including bending, binding and placing in position complete. :-

a)Cold twisted bars.

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. :-

a)1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.

a)1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size).

Reinforced cement concrete in chajjas exceeding 15mm in thickness upto floor two level including centring and shuttering complete but excluding the cost of reinforcement with 1 : 2 : 4( 1 cement: 2 coarse sand : 4 stone aggregate 20 mm nominal size).

Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in:

a)Walls including attached buttresses, pilasters and their caps and bases and string courses etc. up to floor two level.

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Masonry with pre-cast cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) blocks in cement mortar 1 : 3 (1 cement : 3 fine sand) in foundations and plinth.

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position.

Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses.

a)0.63 mm thick GI sheet

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including necessary iron butt hinges with necessary screws.

a)38 mm thick best available local wood, class - B - I

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement.

a)40 mm thick

Providing and fixing 4.0 mm thick asbestors plain sheet ceiling of approved quality with necessary nails etc.complete (frame work for base to be paid separately).

Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling.

a)Best local approved quality wood.

Extra for making chamfered edges of beading.

12 mm cement plaster 1 : 5 (1 cement : 5 fine sand).

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.

a)Ornamental grill.

Painting two coats with oil type wood preservative of approved brand and manufacture on new work.

White washing with whiting on new work (three or more coats) to give even shade.

Providing and fixing 2.50 cm thick approved local wood eaves boards 23 cm wide with necessary mouldings etc.

Applying priming coat consisting of a mixture of red lead, white lead and double boiled linseed oil in the ratio of 0.7 Kg : 0.7 Kg : 1 Litre on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete.

Providing and laying damp proof course 50 mm thick with cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size).

Providing and fixing local wooden railing 0.75 m high with 7.5 x 5 cm top and bottom rails 7.5 x 5 cm sides and 5 cm x 5 cm intermediate vertical bars placed at 22.5 cm centre to centre including painting two or more coats as directed.

Providing and fixing 38 mm thick ( Class - B I ) approved local wood shelves 38 cm wide complete with wooden brackets not more than 1.52 m.

Chequered terrazzo tiles 22 mm thick with marble chips of sizes upto 6mm in floors on 25 mm thick bed mortar 1 : 3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete:

a)Light shades using white cement

Marble chips skirting (up to 30 cm height) rubbed and polished to granolithic finish top layer 6 mm thick with white, black or white and black marble chips of sized from smallest to 4 mm nominal size laid in cement marble powder mix 3 : 1 (3 cement : 1 marble powder) by weight in proportion of 4 : 7 (4 cement marble powder mix : 7 marble chips) by volume.

a)Medium shade pigment with approximately 50% white cement and 50% ordinary cement.

Construction of 2nd class brick masonry chullah 0.75 x 0.45 x 0.25 m with two holes in cement mortar 1 : 6 (1 cement : 6 coarse sand) includng fixing iron gratings 150 mm dia and finishing with mud and gobri plaster complete.

Providing and fixing 40 x 3 mm flat iron hold fasts 40 cm long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm in 1 : 3 : 6 (1 cement : 3 sand : 6 hard stone shingle 40 mm nominal size).

Providing and fixing 12 mm thick and 150 mm wide pelmet of flat pressed 3 layer particle board (medium density) with 25 mm dia second class teak wood curtain rod and brackets including fixing with 25 x 3 mm MS flat 10 cm long and plugs etc complete.

Providing and fixing 25 mm dia first class Indian teak wood curtain rods with brackets plugs etc wherever required.

Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design.

a)Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg).

Construction of soak pit 1.2 x 1.1 x 1.2 m filled with brick bats including SW drain pipe 100 mm dia and 1.20 m long complete as per standard design.

Providing and fixing white vitreous china type water closet pedestal (European type WC pan) with seat and lid CP brass hinges and rubber buffers, 12.5 Litres high level CI flushing cistern with fittings RS or CI brackets, galvanized steel telescopic flush pipe with fittings and clamps, 20 GI overflow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting making good the walls and floors where required.

a)WC pan with white plastic seat and lid.

Providing and fixing a pair of white vitreous china foot rest of standard pattern for squatting pan WC.

a)250 x 125 x 25 mm

Providing and fixing 12.5 litres high level CI flushing cistern of approved make with integral fittings such as ball valve, bell, lever, GI chain and pull complete.

Add electrification 12.50%

Add Furniture

Almirah

Study Table

Dining Table

Dining chair

(Sh: Kitchen cum dinning hall)

Earth work in excavation in foundation trenches not exceeding 1.50 m width of 10 Sqm. On plan or drains not exceeding 1.50 m. in width or 10 Sqm. On plan i/c dressing of sides and ramming of bottoms, lift upto 1.50 M. i/c getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

a) Ordinary Soil

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Providing and laying in foundations and plinth cement concrete 1:4:8 (1 Cement: 4 coarse sand: 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Providing and laying cement concrete 1:3:6 (1 Cement: 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering in :

b) Walls i/c attached buttresses, pilasters and their caps and bases and string course etc. up to floor two level.

Centring and shuttering including strutting proping etc. and removal of form work for :

a) Foundation and plinth

c) Walls including attached buttresses, pilasters etc.

d) Lintels, beams, girders, bressumers and cantilevers etc.

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in :

a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size)

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc. up to floor two level i/c finishing and plastering the exposed surface with cement mortor 1:3 (1 Cement: 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but sxcluding cost of centring, shuttering and reinforcement.

a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). Cum

Reinforcement cement concrete work lintels, beam and bresumers upto floor two level i/c finishing and plastering the exposed surface with cement mortor 1:3 (1 Cement: 3 fine sand) of thickness not exceeding 6mm to give a smooth and even surface but exceeding cost of centring, shuttering and reinforcement.

a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size)

Reinforcement cement concrete in chajjas exceeding 15mm in thickness upto floor two level i/c centring and shuttering complete but excluding the cost of reinforcement with 1:2:4 (1 Cement: 2 coarse sand : 4 stone aggregate 20 mm nominal size)

Reinforcement of RCC work including bending, binding and placing in position complete

a) Cold twisted bars.

Brick work with best available bricks in foundation and plinth in cement mortor 1:6 ( 1 cement 6 fine sand)

Extra for brick work with best available local bricks in superstructure above plinth level up to floor two level.

Half brick masonry (with best available local bricks) in cement mortor 1:4 (1 cement : 4 coarse sand) in foundation and plinth

Extra for half brick masonry in superstructure above plinth level and upto floor level

Brick work with best available bricks 75 mmm thick in cement mortor 1:3 (1 Cement : 3 course sand)

Providing approved best available local wood (Class-BII) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Providing approved best available local wood (Class-BII) work in frames of false ceiling, partition and trusses etc sawn and put up in position.

Providing and fixing panelled glazed or panelled and glazed shutters for doors, windows and clerestory windows i/c aluminium butt hings with necessary screws.

a) 38mm thick best available local wood Class - BI

Providing and fixing 38mm thick wire gauge shutters using glavanized mild steel wire gauge of IS gauge designation 140G with wire of dia 0.56 mm for doors, windows and clerestory windows including anodized aluminum butt hinges with necessary screws.

a) Best available local wood Class B-I

Providing and fixing MS grills of required pattern in wooden frames of windows etc. with MS flat, square or round bars with round headed bolts and nuts or by screws.

a) Ornamental Grill.

Providing and fixing 2.50 cm thick approved local wood eaves boards 23 cm wide with necessary mouldings etc.

Providing and fixing Alu sliding door bolts, bright finished or and black enamelled with nuts and screws etc. complete

Providing and fixing MS Tower bolts(Barrel type) with necessary screws etc. complete.

Providing and fixing MS Handle with necessary screws etc. complete

Providing and fixing 40 x 3 mm flat iron hold fasts 40 cm long i/c fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm in 1:3:6 (1 Cement : 3 sand : 6 hard stone shingle 40 mm nominal size)

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel welded and bolted including special shaped washers etc. complete (welding to be paid separately)

Providing corrugated G.I. sheet roofing fixed with galvanised iron J or L hooks, bolts and nuts 8mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses.

a) 0.63 mm thick G.I. sheet.

Providing ridges or hips 60 cm overall in plain G.I. sheet fixed galvanised iron J or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete.

a) 0.63 mm thick G.I. Sheet.

Providing and fixing 4.00 mm thick ply wood ceiling of app. Quality with necessary nails complete.

Providing and fixing plain square edge wooden beading 38x12 mm section with screws of app. Quality for ceiling.

a) Best local approved quality wood.

Extra for making edges of beading.

Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement.

a) 75 mm thick

12 mm cement plaster 1 : 3 (1 cement : 3 fine sand).

12 mm cement plaster 1 : 5 (1 cement : 5 fine sand).

Painting two or more coats with oil (type wood preservation of app. Brand and manufacuture on new work.

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Distempering (two more coats) with oil bound washable disptemper of approved brand and manufacture of and of required shade on new work over and including a priming coat with distemper primer of approved brand and munufacture to give an even shade.

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 Cement: 3 coarse sand: 6 stone aggregate using 20mm nominal siize) over 75 mm bed of stone ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishi

Construction of cement concrete drain 30cm wide and 23 cm deep in cement concrete 1:3:6 (1 Cement: 3 sand: 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surface with 12 mm thick ce

SH : SANITARY WORKS

Providing and fixing white viterous china wash basin with RS or CI brackets painted white 15mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32mm dia CP brass trap and MI union complete, incliding cutting

a) Flat back wash basin size 550 x 400 mm with a pair of 15mm CP brass pillar taps of heavy quality

Providing and fixing white vetreous china water closet squating pan (Indian type WC pan) size 580 mm with 10 mm and sand cast iron P or S trap, 12.5 litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvani

a) Long pan pattern WC Pan.

Providing laying and jointing glazed stone ware pipe grade 'A' with stiff mixture of cement mortar in the proportion of 1:1( 1 cement: 1 fine sand) including testing of joints etc complete.

a) 100 mm dia SW pipes

Providingand and laying and jointing cement concrete 1:5:10( 1 cement: 5 lime sand: 10 graded stone Agg. 40 mm nominal size) all around SW pipe including bed concrete 15 mm thick as per standred design

a) 100 mm dia SW pipes

Making soak pit 2.50 m dia 3 m deep with 45 X 45 cm dry brick honeycomp shaft and SW drain pipe 100 mm dia 1.80 m long complete as per standard design.

Constructing brick masonry manhole with 2nd class bricks in cement mortor 1:5 (1 cement 5 fine sand) RCC top slab with 1:2:4 mix ( 1 cement 2 coarse sand: 4 stone single 20 mm nominal size) foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 ston

a) inside size 90x80 cm and 45 cm deep including CI over with frame ( light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover and frame to be not less than 38 kg (wieght of cover 23 kg and wi

Add 12.50% Electrification

Please Enable Macros to View BoQ information