PROVN OF SEPARATE TOILET FOR WOMEN MP AT KRIPAN TCP, CATWALK TCP AND HAAT GATE, SPECIAL REPAIR OF BLDG NO OM-08 SINGLE OFFR ACCN OF 20 MTN DIV SIG REGT AND PROVN OF 35 SINK AND 35 UTENSILS RACK IN KITCHEN OF JCOS/ORS MD ACCN NO 4/J/11-126,127 AND 4/J

Amount

Schedule 'A'

Taking down cement plaster from brick walls including raking out joints, hacking for key, scrubbing down with water etc.

Dismantling floor hearth or wall tiling including cement mortar bedding, removing serviceable tile to store and rubbish off the premises.

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness. (Below or above ground level) as directed.

Taking down chowkats or frames n exc 1.5 Sqm each ( without taking off shutters from the frames).

Taking down chowkats or frames exc 1.5 Sqm but n. exc 4.00 Sqm each( without taking off shutters from the frames).

M&L Preparing newly plastered surfaces of walls and apply two or more coat of Anti fungal exterior acrylic based emulsion paintl of required shade : New work (Two or more coat applied @ 1.43 ltr/10 sqm over damp proof priming coat of exterior primer applied @ 2.20 kg/10 sqm) new surfaces.

M & L preparation old decorated surfaces of walls including complete removal of existing treatment and applying two coats of distemper oil-emulsion over a coat of wall putty complete as specified and directed.

M & L Preparing old decorated surfaces of ceilings and applying two coats of white wash.

M & L preparation old decorated surfaces of walls including complete removal of existing treatment and apply two or more coat of Anti fungal exterior acrylic based emulsion paintl of required shade : New work (Two or more coat applied @ 1.43 ltr/10 sqm over damp proof priming coat of exterior primer applied @ 2.20 kg/10 sqm) new surfaces.

M&L Glazed ceramic colour tiles in vertical surface 350x 250x 7 mm/ 200X300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match and including 10mm thick bedding layers in cement mortar 1:4 complete all as specified and directed.

M&L Vitrified Ceramic tiles 10 mm thick (square/ rectangular polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in cement to match white or coloured laid over and including 15mm thick screed bed in cement mortar 1:4 , complete all as specified and directed

M&L Vitrified Ceramic light shade tiles 10 mm thick (square/ rectangular polished, area of each tiles not exceeding 0.36 sqm, in wall etc. set and jointed in neat cement slurry and pointed in cement to match white or coloured and including 10mm thick bedding layers in cement mortar 1:4 complete all as specified and directed.

M & L Machine cut kota stone slab flooring18- 20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and including 15mm thick screed bed in cement mortar 1:4 and jointed with grey cement slurry @ 2 Kg per square

M & L Machine cut kota stone slab flooring 18- 20 mm thick in riser of steps, dado and pillar laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing and including 10mm thick bedding layers in cement mortar 1:4 complete all as specified and directed.

M & L 75 mm thick PCC 1:2:4 Type B-2 (using 40 mm graded aggregate ) for floor, footpath etc.

M&L for chequered cement concrete tiles 20cm X20cmX25mm thich set, joined and pointed in neat cement slurry in floors with grey cement and with grey cement and pigment and including 15mm thick screed bed in cement mortar 1:4 , complete all as specified and directed

S&F 30mm thick PVC cupboard shutter wood free consisting to frame made out of MS tube of 19 gauge thickness and size of 20mmx 20mm for stiles as well as top bottom and lock rail. The inside panel shall conist of 20mm thick multi chamber hollow PVC section of 1mm wall thickness bounded using solvent cement adhesive with 5mm (plus of Minus) thick one side prelam and other side plan colour pvc sheet of Desnity 600 kg/Cbm manufactured by an ISO- 9000 certified company on both side of the inside panel the edge of the panel to be sealed with lapping of 10mm thick & 20mm wide PVC sheet batten (made by sticking 2NOs rigid foam PVC sheets of 5mm plus or Minus) thickness PVC solvent cement adhesive 20mm thick (5mmx4 Nos). Thick PVC sheet to be given for lock provsion at lock height complete as per direction of Engineer-in-charge. manufacture's specification and drawing frame incl size of 60x50 mm, 150mm brass handle, 100mm hinges stainless steel (heavy) 150mm brass tower bolt and cupboard lock (godrej) or equilant and screw and wall plug

S&F in repair 18mm thick plain PVC Ply fixed with with screw/bounded with to PVC adhesive solvent to PVC ply works all as directed. (Make Rajashri or equivalent)

S & F aluminium(powder coated in approved colour) glazed/gauzed window shutters with frame , side hung type with sash bars, including necessary joining cleats for fixing etc, glazing clips, rubber packing, aluminium anodised snap beading, screws, aluminium (anodised) fittings such as peg stays 150mm long-1 No, hooks & eyes-1 set, hinge type B-21 100 mm long-1 No,suitable handle-1 No, locking device, tower bolts, 100mm long 2 Nos and glazing panels with 5.5mm thick coloured/tinted glass with rubber beading, glazing clips and gauzing in with stainless steel wire mesh 0.36mm nominal dia of wire with average 1.40mm width of aperture fixed with aluminium 'C' section, complete all as shown below (a) Frame section shall be of size 100 x 40 x 2.00 mm (Section No.14018) (b) Top & side Members of shutter Section shall be be of size 18.00 x 40.00 x 1.55 (Section No 20738) (c) Bottom Members of shutter Section shall be be of size 18.00 x 40.00 x 1.55 (Section No 20736) (d) Member for wire gauge shutter shall be 18.00 x 43.50 x 1.35 (Section No 20791). Note:- Section No given above are of make Jindal, Contractor may use similar section of other make mention in Appx B

S & F aluminium (anodised) grill, square, ractangular opening of size not less than 75 x 75mm and dia of section shall not be less than 6mm, fixed with channel of size 38 x 12 x 13mm complete all as specified and directed.

S&F powder coated aluminium ventilator shutters with frame (aluminium section weighing 0.55Kg/m), fixed with out sash bars, openable type (Top hung double shutter) and glazing complete with 5.5mm thick coloured/tinted sheet glass and Aluminium wire mesh with necessary clips, hinges, aluminium(anodised) peg stay 30 cm long-01 No. with aluminium (anodised) grill made out of 7mm wide flat, square, rectangular or similar section, fixed with channel of size 38mm x 12 mm x 13mm (Section 8778) complete all as per manufacturer's catalogue 7 specifications (Make: Grill No. 20 of 'DECO GRILL' or equivalent) complete all as shown on drg No. CEAA/64 all as specified and as directed (Make of aluminium section: Jindal/INDAL/ Hindalco)

S & F pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete of size 105 X 60 mm

S & F pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete of size 125 X 60 mm

S & F 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commericial type on both sides and one face is covered with decorative face veneer with lipping/frame to match.

S & F 35 mm thick, 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamferd or rounded, fitted with cut and mitred beads for securing glass etc size of member of shutter as specified in SSR Part-I Section 8 Clause 8.24(a), etc complete all as directed by Engineer-in-charge.

S&F, 250mm aluminium alloy, anodised sliding door bolt with hasp, staple (bolt tyoe) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed

S & F 140mm floor door stopper of aluminium alloy body and tounge, anodised, with hard drawn steel spring ,fixed in floor complete as all as specified and directed.

S & F M S 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete as all as specified and directed..

M&L preparation of new painted wooden surfaces of any description exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

M & L preparation of old painting steel surface with one coats of synthetic enamel paint prepared steel surface.

S&F in repair, 20mm dia aluminium anodised curtain rod complete all as specified and directed.

S&F in repair, brackets for 20mm dia curtain rod complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern ), white (excluding fixing bolts, flushing cistern and flush pipe), including connection to drain (or out going pipe) and to flushing pipe, antisyphonage pipe etc. complete fixed in repair

S&F in repairs, 10 litre capacity PVC valve less syphonic action type, flushing cistern, low level, white, with inlet, ball valve, flush pipe, float and handle including brackets complete as specified & directed. Make. Hindware, prayag.

S&F in repair CP body cleaner Health faucet with 1Mtr tube and hook (Baded tube) white/Ivory Cat No- 187 (make- Prayag)

S&F in repair CP Toilet paper holder Cat No- BA-88 (make- Prayag)

S&F in repairs Vitreous China wash basin, size 550 x 400mm, white, flat back, with waste, coupling, chain and plug and porcelean stopper & backets including cutting for and pinning in ends of brackets but excluding tap complete as specified and directed.

S&F in repairs 32mm brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed

S&F in repair brass CP mixer 15mm bore for mixing hot & cold water screwed down for iron pipe and fixed

S&F in repairs, 15mm bore, CP mixer tap connecting hose pipe 450mm long with nuts at both ends complete.

S&F in repairs, 15mm bore, PVC connecting pipe 450mm long with PTMT nuts at both ends complete.

Taking up or down 15mm dia steel tubing & connection including cleaning for refixing or removal to store Complete all as specified & directed.

Taking up or down 20mm dia steel tubing & connection including cleaning for refixing or removal to store Complete all as specified & directed.

S&F in repairs CP brass shower rose with swival joints complete fancy type for 15mm bore pipe, fixed as in repairs, complete all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60 cm long between flanges..

S&F in repair Corner glass shelf 300mm Cat No- BEA-44 (make- Prayag)

S&F in repair glass shelf 500x60mm (with ABS Brackets) Cat No- BEA-47 (make- Prayag)

S&F in repairs 15 mm bore, Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions as specified.

S&F in repairs, 15mm bore, bib taps, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete.

Taking down PVC pipes including all fittings like shoes, bends, swan necks etc of any dia all as specified and directed.

S&F PVC (SWR) bend any radius for 110 mm bore pipe incl jointing material complete all as specified and directed.

S&F PVC (SWR) junction single, (Single T) equal or unequal for 110mm dia bore as specified and directed.

S&F PVC (SWR) bend any radius for 75 mm bore pipe incl jointing material complete all as specified and directed.

S&F PVC (SWR) junction single, (Single T) equal or unequal for 75mm dia bore as specified and directed.

S&F in repair grating doom 100 mm dia with waste hole of PTMT.(Minimum weight 25 gms)

S&F in repairs, rotational moulded polythene water storage tanks, double layered (Cylindrical vertical with closed top) of capacity 500 lit, hoisted and fixed in position as in repair including taking down old tanks complete all as specified.

S&F in repair ball brass valve, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed to dia of pipe 20mm.

M & L 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection / hard standing etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete as specified and directed.

Surface excavation n.exc (not exceeding) 7.50 cm deep and averaging 15cm deep and getting out complete all as specified and as directed.

Excavation in trenches, n exc 1.5 mtr wide and n exc 1.5 mtr in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. n exc 10 Sqm on plan and n exc 1.5 mtr in depth and getting out in soft/loose soil complete all as specified and as directed by Engr-in-Charge.

M&L PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) for fdn/ mass concrete complete all as specified and as directed by Engr-in-Charge..

M&L for PCC for concrete bed to drain pipe , 150 mm bore pipe including packing and under hunching against the sides of pipe after they are laid and tested in PCC (1:3:6) type C-2 using 40 mm graded stone aggreagate complete all as specified and directed.

M&L for 150 mm bore grade 'A' SGSW drain pipe laidin trenches and jointed in cement ,mortar (1:1) complete all as specified.

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in flooring 25 mm thick surface finished even and rough to receive the top layer complete all as specified and directed..

M&L for RCC Type B-1, M-25 (20 mm graded aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified.

M&L RCC Type B1 M-25 (20 mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L RCC Type B1 M-25 (20 mm graded aggregate) in Columns, pillars, piers, posts and struts

M&L TMT bars 16mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Ditto as above but 6 to 8mm dia

M&F Formwork flat fair finished to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified.

M&L formwork flat fair finishes surfaces to sides and soffits of floor or roof beams, beam haunching, grders, bresssummers, linterls, centilivers, shelves incvluding support over hangs etc. also spays between floor and beams etc. complete all as specified and directed.

M&L Formwork square, rectangular or plougonal fair finished surfaces to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified.

M&L for Formwork to flat fair finished to soffits of suspended slabs such as roof slabs, floor slabs, landings , shelf and similar work; not exceeding 200mm thick (Horizontal or sloping)

M&L for Flyash Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortor 1:6 complete all as specified and as directed by Engr-in-Charge.

M& L for Fly ash Brickwork with sub-class `B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified and as directed by Engr-in-Charge.

M&L for rendering 15 mm thick on brick work or concrete surfaces in cement mortar (1:4) finished surfaces even and smooth complete all as specified and as directed.

M&L for rendering 15 mm thick on brick work or concrete surfaces in cement mortar (1:6), finished surfaces even and smooth complete all as specified and as directed.

Rendering 10mm thick with CM (1:3) on or concrete surfaces finished even and smooth as in ceiling complete all as specified and as directed by Engr-in-Charge.

M&L for preparing new plastered surfaces of wall with wall care putty and applying two coat of distemper oil emulsion over a coat of primer complete all as specified.

M&L for preparation new plaster surfaces of wall and applying two coats of cement base paint complete all as specified and as directed by Engr-in-Charge.

M&L preparation of new plaster surface of ceiling and applying three coats of white wash complete all as specified and as directed by Engr-in-Charge.

M&L preparation of old surface on wall and applying two coats of white wash matching of existing surface complete all as specified and as directed by Engr-in-Charge.

M&L Hardcore of gauge n exc. 63 mm, except material retreived from item 1 deposited, spread and levelled in layers n exc.15 cm thick, watered and rammed to a true surfac

M&L silver sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed by the Engr-in-Charge.

M & L Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade complete jointed with gray cement and pigments including side coping all as specified and as directed by Engr in Charge.

M&L for cement concrete type B-1 1:2:4 (20 mm graded stone aggregate) as in floor finished complete all as specified and as directed by Engr-in-Charge.

M&L for Damp proof course to horizontal or vertical surfaces in cement mortar 1:2:4 type B0 including necessary formwork

Ditto as in skirting

Supply & fix as for steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay complete with glazing bars, dovetailed or welded all as directed by the Engr-in-Charge.

All as per item No 90 here-in-before but without glazing bars.

M&L for Framed work such as grills, framed guard bars,for window by welding it to existing window frame and similar work con- forming to Fe.290.Gde-E-165

S&F Steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel, complete all as specifed.

M&L for PCC 1:3:6 type C-2 using 40 mm graded stone agg as in plinth protection complete all as specified and as directed.

S&F of 4 mm thick Sheet glass frosted , ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane

M&L for two coat of synthetic enamel paint over a coat of yellow primer including preparation on New steel surfaces of any description over 10 cm width or girth complete all as specified and as dircted.

S&F 15 mm dia medium grade galvanized steel tubing with all fittings fixed to walls, ceilings or laid under floors all as specified and directed.

M&L for 20mm GI tubing medium grade with all fitting laid in trenches / wall for bore of pipe complete all as specified and as directed :-

M&L for 25mm GI tubing medium grade with all fitting laid in trenches / wall for bore of pipe complete all as specified and as directed :-

S&F of 40mm bore waste coupling of PTMT (half or full threaded) minimum weight 60gms incl waste pipe complete all as specified and as directed.

S&F sinks with drainage board made of stainless steel 01mm thick kitchen or laboratory with drainage board with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including fixing of kitchen sinks to the wall making holes to the wall and necessart MS bracket complete all as specified and as directed by the Engineer in charge.

Supply and fix stainless steel kitchen plate rack of size 31"x31"x10" and 1 mm thick specified and directed by the Engr-in-Charge.

M/L for 20mm gun metal gate valve with iron wheel head screwed both side of following sizes completed all as specified and as directed.

M/L for 25mm gun metal gate valve with iron wheel head screwed both side of following sizes completed all as specified and as directed.

S & F vitreous china wash down water closet wall hang (Pedestal) including PVC seat cover closed pattern with flat bottem and cover and mild steel chromium plated hinge device,connection to drain or outgoing pipe and to flushing pipe, antisyphonage pipe joint to socket or stoper etc.

S/F of 10 litres cap PVC low level valve less symphonic action type flushing cistern white with inlet, ball valve, float and handle including brackets and flushing pipe, complete all as specified and as directed by Engr-in-Charge

S&F Vitreous China wash basin Pedestal pattern, white, flat back size 580x450 mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipeincluding brackets, complete all as specified and as directed by Engr-in-Charge.

S&F 15mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed by Engr-in-Charge.

S&F 15 mm dial PVC connection 450 mm long, complete all as specified and as directed by Engr-in-Charge.

S&F waste coupling of PTMT (half of full threaded) complete all as specified and as directed by Engr-in-Charge.

S&F 32 bore PTMT Wash hand basin waste pipe 90 cm long complete all as specified and as directed by Engr-in-Charge.

S&F Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified.

S&F 15mm bore Bib taps, cast copper alloy fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S&F 15 mm bore Stop valves, cast copper alloy, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F Towel Rail 450mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 170gms)

M&L for coloured Glazed ceramic tiles in vertical surface 600x600 x5 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in CM (1:3) complete all as specified.

M&L for coloured joint free non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tile including 15mm thick screed bed in cement mortor 1:6 complete all as specified

S&F CP toilet paper holder complete all as specified and directed.

M&L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement

M&L for 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

Ditto as above but in wall complete all as specified.

M&L for 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

M&L for 110 mm bore PVC (SWR) vent cowl

M&L PVC (SWR) bends with access door of 110mm bore any radius complete all as specified.

S&F 1000 ltr Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified.

Returning filling in including spreading levelling watering and well ramming in layers not exc 25 Cm complete all as specified and as directed.

Removing excavated material exc 1.5 km n.exc 5 KM and depositing where directed at a level n exc 1.5 mtr above the starting point complete all as specified and as directed by Engr-in-Charge.

Material & labour for PCC in 1:3:6 type C1 ( using 20 mm graded stone aggregate) as in surface channel including necessary formwork.

Extra for forming fair finished drain 30 cm inner girth

M& L for Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long

M&L for CP toilet paper holder of any description all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing.

S&F Stainless steel butt hinges medium weight 100mm long for PVC door.

S&F Aluminium anodized barrel tower bolts, extruded section 200mm long.

S&F Aluminium anodized handles, D type, 150mm long

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

M& L for fabrication and fixing of powder coated aluminium door shutter fixed with rubber gasket, stopper, cleats, handles etc complete for aluminium frame of size 101.6mm x 44.45mm x 2mm and section of bottom and top rail of section114mmx44.45mmx2mm thick and and lock rail shutter frame of 83mm x 44.45mm x 2 mm with and including panels of 5.5 mm thick plain/frosted float glass,and with anodised aluminium snap beading of size 18.2mmx16.66mm scred for fixing fully including double action door spring hydraulically regulated made up of 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and all necessary fittinngsand EPDM rubber packing each shutter shall be provided with two decorative type aluminium disc handle of 150 mm dia per shutter ,1 no heavy duty door shutter 1no 200mm long aluminium tower bolt per shutter including taking down old onecomplete all as specified and as directed by the Engr-in-Charge.

S&F powder coated aluminium Three track sliding window comprising of one fly proof shutter and two glazed shutters with window frames of size 92mm x 31.63mm x 1.50mm thick and shutter frames of size 40mm x 18mm x 1.55mm thick with necessary joining cleats, glazing clips, rubber gasket, anodised aluminium snap beading and connected locking arrangement and with aluminium Deco grill DG/01 7x4.5mm thick, fixed with channel of size 38mm x 12 mm x 13mm (Section 8778) complete. (Notes : (i) Glass filling in panels of windows and aluminium wire mesh/wire cloth shall be deemed to be included in the quoted rate for the item. (ii) Aluminium alloy wire cloth in panels of wire gauzed shutter shall be 0.45 mm nominal dia of wire and avg width of aperture 1.40 mm, fixed with aluminium wire staples shall be deemed to be included in the quoted rate for the item. (iii) Glass filling in panels of glazed shutter shall be 5 mm thick tinted sheet glass of approved make and shade/tint shall be deemed to be included in the quoted rate for the item (Make of powder coated aluminium section: Jindal/INDAL/ Hindalco)

Construction of new brick masonry valve pits of size 600x600x600mm Iinternal dimension) with brick work in cement mortar (1:4) 40mmx40mmx6mm ang;e iron frame, MS handle 300mm long bent to shape and riveted to MS sheet including excavation and earth work, concrete work 3.15mm thick MS sheet cover with locking arrangement hinges and handle rendring work, painting to all steel surface with two coat red oxide primer completed and all as directed.

Taking down tar felt with cement plaster from roof surfaces and lowering and removing the same to a distance exc. 50m and n. exc. 100m incl roughening of old concrete suirface of roof by wire brushing and cleaning the surface to remove all loose dust etc complete all as specified and as directed .

M & L screed bed or bedding layer 15 mm thick screed bed or bedding layer in CM (1:4) mixed with WPC as per manufacturer instruction for laying of APP membrane complete all as directed by the Engr-in-Charge.

Supply only intergral water proofing compound (WPC) of best quality

M& L for bituminous primer @ 0.50 KG/Sqm over the cement plaster incl preparation of surfaces as per manufacturers instruction complete all as specified and as directed by the Engr-in-Charge.

M & L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and as directed by Engr in Charge.

M & L for finishing the Bituminous surface with aluminium paint @0.15 Ltr/sqm as per manufactures specifications complete in all respects as directed by Engr-in-Charge

ELECTRICAL WORKS :- Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

M&L for Concealed type point wiring with 1.5 sqmm (nominal cress-sectional area) PVC insulated unsheathed single core multi stranded copper FRLSH cable working voltage 1100 volts grade conorming to IS-694 with stranded copper conductor including PVC conduit of adequate size having a wall thickness ont less than 1.5 sqmm with all accessories (including cutting chases & making good the disturbed surface to its original specifiecation) including 1.5 sqmm (nominal cross sectional area) PVC insulated unsheathed single core multistranded copper conductor FRLS cable as earth continuity conductor connected to main switches/DB's or common earth dolly complete all as specified and directed for the following:- Make of cable:- KEI/Havells India Ltd/Finolex/Nicco/HPL One light point controlled by one way switch 5/6 amps

One Exhaut fan point controlled by one way switch 5/6 amps.

One Socket out let 5/6 amps point on the independent board

One bell/buzzer point controlled by one bell push button

One light point controlled by two way switch 5/6 amps.

All as per item No 148 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified and directed.

M&L for point wiring complete for one socket outlet 15 Amps point on independent board with 4 Sqmm multistranded copper conductor single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less that 20mm dia and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 4 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) as earth continuity conductor connected to common earth dolly, fabricated sunken terminal box made out of GI sheet steel not less than 1.22 mm thick for boxes upto a size of 200 x 300mm and above this size not less than 1.63 mm thick duly painted with aluminum inside and anticorrosive paint outside, concealed in walls, with 3mm thick bakelite/plastic laminated sheet top cover fixed with cadmium plated iron screws for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCBs or bus bar shall be done through proper size copper/brass thimbles.

S&F switch piano flush type 5/6 amps single pole one way complete all as specified and directed. Make : Havells Reo

S&F socket 2 in 1, 5 Pin, 5/6 amps, white ivory finish flash type complete all as specified and directed. (Make : Havells Reo

S&F of socket outlet 2 in 1, 5 Pin, 5/15 amp, multipurpose 230 volt flash type complete all as specified and directed by Engr-in-Charge. Make : Havells Reo.

S&F switch piano flush type 15/16 amps single pole one way complete all as specified and directed. Make : Havells Reo.

S&F in repair bell/buzzer push 5/6 amps flush type white/ivory finish complete all as specified and directed.

S&F in repair switch piano type 2 way 5/6 Amp, 230 Volt, flush button single pole one way complete all as specified and directed by Engineer -in-Charge.

S & F in repair deluxe fan Electronic regulator AC 50 Hz, 100 watt, rotary step type, white/ivory finish complete all as specified and directed.

S&F ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified and directed Make : Havells Reo.

S & F lamp holder, insulated body, with back plate suitable for batten/angle fittings complete all as specified and directed Make : Havells Reo.

S & F Wall mounted LED Tube light fitting 20W, with extruded aluminium housing, with integrated LED driver complete all as specified and directed

M&L for bldg security lighat bracket made out of GI pipe light grade 25 mm dia 1.2 mtr length bent to shape and reduced to required size at top upto 1.2 mtr length by cutting, welding and well finishing including MS clamp of flat iron of size 25 x 5 mm suitable length 2 Nos complete with drilling hole, fixing with runts bolts and washers including painted with two coats aluminium paint over a coat of red oxide primer.

S & F LED security light fittings 45 watt in aluminium housing, Lens embedded PC cover having top with IP66 protection complete all as spedified and as directed.

S&F Sheet metal enclosure for 4 way Distribution Boards (DB’s), double door, single pole & neutral with 200 amps rated bus bar, IP-20 protection suitable for fixing MCB"S/lsolators complete all as specified and directed.

S&F MCB, Single pole & neutral 5 to 40 amps, 240 volts, ‘C’ curve, 10 KA all complete as specified and as directed .

S&F MCB, Single pole, 6 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete as specified and as directed .

S&F MCB Isolator Triple pole and neutral 40 amps, 415 V, 10kA all complete as specified and as directed.

S&F MCB Single pole, 5 to 40 amps, 240 volts, ‘C’ curve, 10 KA all complete as specified and as directed.

Material and labour for earthing complete with galvanised steel plate electrodes of size 600x600x6mm thick burried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised 25x4 mm dia earth lead by means of nuts bolts check nuts GI washers earth wire protected by galvanised iron pipe 32 mm bore (light grade) for building LT wall panel all as directed including concrete pit in PCC (1:3:6) type CI, precast RCC cover slab of size 30x30x10 cm with one handle for lifting made out of 8 mm diameter MS bar finnel wire mesh 20 mm bore galvanised iron pipe (medium grade) for watering charcoal or coke and salt in alternate layers necessary earth work in soft/loose soil complete all as shown in electrical plate No 5 of SSR Part I including testing on completion all as specified and directed.

Supply & fix exhaust fans metal body AC single phase 230/ 240 V of size 300 mm sweep with louver

M&L for making hole on existing wall for fixing Exhaust fan and making good to the disturbed surfaces complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation of poles/stays/cables etc and getting out in any type of soil.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers n.exc 25cm.

Removing excavated material n.exc 50m and depositing were directed at a level n.exc. 1.5m above the starting level.

M&L for sand cushioning in cable trenches over & under the cable, with river washed coarse sand, as per standard practice with proper compaction complete all as specified and directed by Engr-in-Charge. (Punned thickness 18 cm shall be considered for payment as per para 19.75 of SSR Part-I)

M&L for brick protection for protection of cable over sand cushioning cables inside the trench by using common brunt clay building bricks sub-class “B” laid dry and flat and width wise along the axis of the trench complete all as specified and directed by Engr-in-Charge

Supply and laying, jointing and testing in trenchs or passing through pipe cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, LT electric power cables (heavy duty) 1100 Volts grade with multistranded aluminium conductor of size 10 sq mm 2 core with all fixing and connecting accessories cable lugs, nut bolts,washer etc all as specified and directed.

S &F GI tubing light grade 40 mm dia for protection of cable passing through duct / road crossing / on pole / on wall tc including all fitting and fixing arng like clamps made out of 25mm X 3mm flat iron and nut bolts all specified and as directed

S & F Bulk head luminaire suitable for 10 Watt LED (or nearest next higher wattage) light IP66 grade, luminaire efficiency not less than 120 lumens/watts with and including 10 watt LED (or nearest next higher wattage) lamp and connecting up with and including PVC insulated 3 core of size 0.75 Sqmm copper conductor from ceiling rose to terminal block of light fitting including necessary taking down the old unserviceable fitting complete all as specified. Cat No :- HEXAFT10WLED857SSWYMBOPC, Make – Havells or equivalent make of Crompton/Bajaj

S&F, IP 20, class I, LED light 1X18 W (or nearest next higher wattage) (4feet), 5700K, wall/ surface mounted, integrated type with aluminium housing and decorative and caps with integrated high efficiency electronic driver and surge suppressor of 2KV or more, luminaire efficiency > 95 lumens/watt, power factor > 0.90, operating range - 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting up with and including necessary taking down the old unserviceable fitting complete all as specified. Cat No :- LUMILINEPLUSBS18WLED865SPCSS, Make – Havells or equivalent make of surya/Bajaj

S&F IP 20, Class I, LED Mirror light fitting 1 x 10 W, (or nearest next higher wattage) 5700 K, wall /Surface mounted with aluminium housing 2 feet long, integrated type, with high efficiency PMMA diffuser, integrated high efficiency electronic driver & surge suppressor of 2 KV or more, luminaire efficacy > 95 lumens/Watt, power factor >/ 0.90, operating range – 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/square blocks, screws etc complete including 01 No 10 W LED lamp with all accessories internally prewired and including connecting up with and including twin core twisted flexible copper conductor cable of suitable size including necessary taking down the old unserviceable fitting complete all as specified. LUMILINEPLUSBS10WLED865SPCSS, Make – Havells or equivalent make of surya/Bajaj/Havells

S & F Decorative wall light fixture made up of Polycarbonate suitable for 10 Watt (or nearest next higher wattage) LED light having B-22 base lamp holder with and including 10 watt LED lamp and connecting up with and including PVC insulated 3 core of size 0.75 Sqmm copper conductor from ceiling rose to terminal block of light fitting including necessary taking down the old unserviceable fitting complete all as specified

Material and labour for concealed sub-main wiring alongwith earth wire of size of 2 x 6.0 sq. mm + 1 x 6.0 sq. mm earth wire, ISI marked, FRLSH, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC rigid conduit (medium grade) of of size not less than 25 mm with all fittings and accessories ISI marked including cutting chases for conduits & making good to walls, floors etc complete, including taking down old unsv aluminium submain wiring all as specified and as directed. NOTE : Two runs of 6 sqmm conductor for main and one run of 6 sqmm conductor as earth wire with proper colour coding including one run run of PVC conduit shall be measured as one unit length. Connections of cables wit MCBs or bus bar shall be done through appropriate size brass/ copper thimbles

S&F Sheet metal enclosure for 4 way Distribution Boards (DB’s), IP-43 double door, Tripple pole & neutral with 200 amps rated bus bar, IP-20 protection, including four pole MCCB 63 Amps with blanking plates complete all as specified and directed.

S&F MCB distribution boards (DBs) with sheet metal enclosure, double door, IP 43 protection, 240 Volts, 8way, single pole and neutral, with 200 Amps rated copper bus bar (as per OEM), neutral link, ert5h link earthing studs, suitable for fixing MCBs, without MCBs fixed flush to wall/other surface complete all as specified and as directed

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers etc incl making connections with 3 core flexible multistranded copper conductor of size 0.75 Sqmm run through flexible pipe all as specified and as directed including cutting holes and making good the disturbed surfaces of walls in CM(1:4) and finishing the surface as per existing color scheme. Make : Usha or equivaleny in Havells / Orient

Takingout Ceiling Fan 1200 mm sweep from its position and Refixing ofter B/R plaster work complete all as specified and as directed.

Material and labour for earthing with GI earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground vertically to depth not less than 2.25m below the ground level with top edge of earth plate at a depth not less than 1.5m below the ground level connected to galvanized iron wire 4mm dia earth lead by means of bolts & nuts,check nuts & washers made of galvanised steel, earth strip protected by and including PCC (1:2:4) type B1 precast RCC cover slab (M-15) reinforced with 8mm dia TMT bars 100mm center to center bothways including one handle made of 10 mm dia round bar, including necessary excavation and earthwork in any type of soil, 20 mm dia medium grade galvanized steel tube for watering with one end fixed with cast iron funnel and wire mesh, 15 mm bore medium grade galvanized steel tubing for drawing earth lead GI strip protection & common salt, charcoal in alternate layers etc. complete all as shown in EP No 3 of SSR Part 1 2009 and testing on completion complete including dismantling the existing unserviceable earthing complete all as specified and as directed.

L. B. SHARMA

Biswanath Sharma