Electrification and telecommunication works in new Safety dept building at FACT UC

Electrification and telecommunication works in new Safety dept. building at FACT UC

Supply, erection, termination and servicing of single/double door 8 way, Three phase , 415 Volts MCB TPN DB having the following specification: 1) 63A Three pole isolator - 1 No. 2) 63A Three pole RCCB with sensitivity of 30mA -1 No 3) 32A double pole C type MCB - 6 Nos 3) 16A single pole B type MCB-4 nos 4) 10A single pole B type MCB-8 nos DB has to be flush mounted on to the wall.

Supply, erection, termination and servicing of single/double door 8 way, Single phase , 230 Volts MCB emergency Lighting DB, having the following specifications: 1) 32A Double pole isolator - 1 No. 2) 32A double pole RCCB with sensitivity of 30mA -1 No 3) 10A single pole B type MCB- 4 nos DB has to be flush mounted on to the wall.

Supply, surface/conceiled fixing and servicing of 4 pole surface mounted manual changover switch with the specifications as follows: Rated operational current: 125 Amps Utilization category: AC-23A Rated operational voltage : 415V Operating Frequency: 50 Hz Enclosure type: SS Conformance to Standards: IS/IEC 60947-3, EN 60947-3 Standard Accessories: Terminal Shroud,Phase Barriers,Source Separator, Extended handle with shaft

Supply of 4CX25 sq.mm XLPE Aluminium armoured Cable

Laying and clamping of cable of size 4CX 25 sq.mm XLPE aluminium armoured Cable, from Load centre to manual change over switch. Scope of work includes : 1) Laying cable through MS cable trays/walls/trenches/GI pipes by properly clamping the cable at distance not exceedding 50 cm with aluminium clamps/ GI metal saddles. 2) Holes through walls should be made by the contractor if required. All the materials including clamps, fasteners etc. required for this work are under the scope of contractor.

Glanding and termination of armoured cables of size 4CX 25 to 4CX 35 sq.mm using single/double compression glands. All the materials including cable, glands of required sizes, lugs(bimetallic if required), fasteners etc. required for this work is under the scope of contractor.

Supply of 4Cx16 sq.mm XLPE Aluminium armoured Cable

Laying and clamping of cables of size 4CX 16 sq.mm PVC/XLPE Aluminium armoured Cable , from existing DB to emergency Lighting DB. Scope of work includes : 1) Laying cable through MS cable trays/walls/trenches/GI pipes by properly clamping the cables at distance not exceedding 50 cm with aluminium clamps/ GI metal saddles. 2) Holes through walls should be made by the contractor if required. All the materials including clamps, fasteners etc. required for this work are under the scope of contractor.

Glanding and termination of armoured cables of size 4Cx16 sq.mm using single/double compression glands. All the materials including cable, glands of required sizes, lugs, fasteners etc. required for this work is under the scope of contractor.

Supply of 25 A modular plug socket and 25A DP modular switch, same as item used in schedule no.13

Supply, installation and servicing of recess mount type 36W, 120 lumen/watt- 2ft x 2ft LED light with color temperature of cool white/day light. The installation of lighting fixtures shall be on the false ceiling, as per the drawings or as instructed by the engineer in charge. The scope shall include terminations of cables on lighting fixtures, fixing lamps and accessories. Supply of lamp including all required accessories such as frames for fixing lamp on to the false ceiling, suspension rod/chain, clamps, bolts, nuts, screws, washers, copper flexible cable,PVC box for fixing ceiling rose, PVC Junction boxes(2/3/4 way) etc. for properly fixing the light fitting on to the ceiling wherever required are under the scope of contractor. Preparation and fixing of concealed ceiling roses/junction boxes, drawing earth wires of 1.5 sq.mm flexible copper cable of green colour pvc for metal body earthing ,connecting, testing and commissioning are under contractor's scope.

Supply of recess mount type 36W, min 120 lumen/watt- 2ft x 2ft LED light, as spares for the work specified in Schedule No- 16

Supply, installation and servicing of surface mount type 36W, min 120 lumen/watt- 2ft x 2ft LED light with color temperature of cool white/day light and including surface mounting frame. The installation of lighting fixtures shall be on surface of ceiling,as per the drawings or as instructed by the engineer in charge. The scope shall include terminations of cables on lighting fixtures, fixing lamps and accessories. Supply of lamp including all required accessories such as frames for fixing lamp on to the surace of ceiling,clamps, mounting frame on to surface, bolts, nuts, screws, washers, copper flexible cable,PVC box for fixing ceiling rose, PVC Junction boxes(2/3/4 way) etc. for properly fixing the light fitting on to the ceiling wherever required are under the scope of contractor. Preparation and fixing of concealed ceiling roses/junction boxes, drawing earth wires of 1.5 sq.mm flexible copper cable of green colour pvc for metal body earthing , connecting, testing and commissioning are under contractor's scope.

Supply of surface mount type 36W, min 120 lumen/watt- 2ft x 2ft LED light as spares for the work specified in Schedule No- 18

Supply, fixing and servicing of surface mounting type square shaped LED downlighter of wattage 20W-25W ,>80 lm/w, cool white/day light colour with all the required accessories for fixing.

Supply, fixing and servicing of 20W LED batten type tube light fittings surface mounted with required clamps/ fasteners.

Supply of 5 nos spare LED drivers for LED light fittings mentioned in schedule 16 and 18

Supply, fixing and servicing of 1200 mm span BLDC remote controlled ceiling fans , 230V on to the ceiling. All the required fasteners/ acessories / fans are under the scope of contractor.The service value of wall fan shall be higher than 5.5 CMM/Watts.

Supply, installation and servicing of 400mm remote controlled BLDC wall fan with suitable clamps/fasteners. Supply of all materials required for the work shall be under the scope of the contractor. The service value of wall fan shall be higher Than 5.5 CMM/Watts.(Refer BEE Guide lines for service value and Star Ratings)

Supply of 400mm remote controlled BLDC wall fan as spares for the work specified in Schedule No- 24

Supply, Fixing and servicing of BLDC exhaust fan of sweep 200mm of non metallic body with louvre. All accessories and fasteners required for the completion of work are in the scope of contractor. Colour white/ivory

Supply of 200mm BLDC Exhaust fan as spares for the work specified in Schedule No- 26

Supply, Fixing and servicing of exhaust fan of sweep 225mm of metal body . All accessories and fasteners required for the completion of work are in the scope of contractor.

Supply, Fixing and servicing of Ex. Fan 300mm of metal body. All accessories and fasteners required for the completion of work are in the scope of contractor.

Supply of 100 mm. NB(GI-Class B) GI pipes

Excavation of existing / new cable trenches in ordinary soil for laying cables/GI pipes for routing cables, refilling the trench and consolidating. All the materials such as sand, brick etc. as required shall be brought by the contractor.

Supply, fixing and servicing of 50 pair Telephone distribution box suitable with KRONE type terminals. It should include 5 Piece of 10 Pair Krone Module and complete with terminal/tag blocks as required, cable glands /bushes of suitable sizes and all other required hardwares. The junction box shall be wall mounted / flush mounted as per requirement at site and with conduit entry for 1 No. 20 pairs incoming cable and min 6 outgoing cables. Body material: Powder Coated Sheet Steel with 1.37 mm thickness (minimum).The scope shall include supply and fixing of telephone distribution box with all the hardwares required for the same. All spare entries of the junction boxes shall be suitably blanked.

Supply and concealed fixing of 6 modular metallic box with frame and plate suitable for fixing modular type RJ11 telephone sockets.

Supply of RJ11 telephone socket with shutter.

Supply of dummy plates for modular box mentioned in schedule 33

Supply of 23 AWG Solid bare copper (4 pair) CAT 6 outdoor UTP cable for CCTV

Laying of 23 AWG Solid bare copper (4 pair) CAT 6 outdoor UTP cable for CCTV through 25mm dia PVC conduit. Fixing of conduit is under schedule 39.

Cutting into walls for executing concealed PVC conduit wiring and replastering after the work. All the tools & materials for this work shall be under the scope of the contractor

Concealed fixing of 25mm ISI marked PVC conduit through wall. The work include cutting through wall, fixing PVC conduit and replastering back to normal.All the items required for the works like 25mm PVC conduits, junction boxes(as per FACT requirement) clamps etc. are under the scope of contractor

Core cutting through wall of diameter 2.5 inch. The required machinery for core cutting shall be brought by the contractor.

Supply, erection, testing, commissioning and handing over of GI plate earth pit as per IS 3043. The scope shall include supply of GI earth plate of size 600x600x6 mm connected with GI pipe electrodes,GI strips, GI nuts, bolts and washers,cable lugs, funnel etc for earthing work. The plate shall be buried vertically in the ground at a depth not less than 3.0 meters from ground level to the top of the plate. The earth connection should be joined to the plate at not less than two separate points using GI strips of dimension 25mmx5mm or higher. The scope of work shall also includes excavation of earth pit, refilling with chemical earthing compound, applying anticorrosive paints, construction of inspection chamber with RCC cover slab (pre-fab inspection chamber is also acceptable), digging of trenches ,laying of earth cables , glanding and termination of cables etc. The earth pit electrode must be connected to DB using two runs of copper earth cable and properly terminated with lugs. The supply of earth cable, laying are mentioned as another scope of work in schedule 42 and 43. Materials required for the constructions of inspection chambers such as cement, M-sand ,brick etc and all other accessories required for the completion of work shall be supplied by the contractor. Installation, testing and commissioning are in the scope of contractor.

Supply of 10 sq.mm copper multistrand copper cable for earthing

Laying and termination of 10sq.mm multistrand copper cable for earthing. The scope of work include laying cable through pipes/wall by properly clamping.

V V ELECTRICALS (BID ID -3286490)

LAMOS TECHNOLOGY SOLUTIONS PVT LTD (BID ID -3286344)

PEEJESS ELECTRICALS (BID ID -3285297)