REPAIR OF INTAKE WELL TREATMENT PLANTS PUMP HOUSE ETC UNDER MASI PUMPING WATER SUPPLY

Amount

20 mm thick cemenrt plaster 1:4

Supply fixing of door, Window, Steel Ladder & Railling

Supply fixing of girder, chain pully for lifting of pumps from well

150 mm dia. Cast steel Reflux / Swing Check Valve, Class 150 (MR)

Supply & fixing of Nuts & Bolts to fix casing size of bolts 30mm dia & 30 cm long

Supply & fixing of 200 mm dia sluice valve

fixing of 200 mm dia mserw 4.0 mm thick sanction pipes & deliverypipes excluding of cost of pumps

P.C.C. 1:2:4 for installation of water pumps.

Snowcem painting two coat on in intake well & pump house (Inside and outside)

One coat white washing & two coat distemper in pump house

Supply of all materials & construct PCC drain along the appron including Supply of labour T&P etc. complete.

Supply & fixing of inlet, outlet,wash out and overflow 200 mm dia,4.8 mm thickness,MSERW pipe with complete arrangment

Supply & fixing of 150 mm dia sluice valve with complete arrangment

Supply of all material, construct sluice valve chamber of following sizes as per type design (1.2 M X1.2 MX1.0 M)

M.S. or Iron work in M.S.jal on top of settling tank to protect water from wild animals, debris.

Supply of all materials, labour. T&P etc. complete and Apply one coat of white washing & two coat of snocem as per instruction given by engineer in charge

GI pipe Railing (3 Rows of 20 mm dia. Pipe)

Supply and laying 10-20 mm coarse aggregate of filter media of required uniformity and coefficient.(NSI)

Fixing of outlet,inlet, washout, over flow, bye pass arrangement etc. complete, including cost of pipe supply and fiting of each bed. Approximate length of 150 mm dia of GI pipe

62mm thick C.C apron in 1:2:4 cement, sand and 10-20 mm gauge stone grit over 50 mm base in 1:4:8 cement, sand and 25-40 mm gauge stone ballast including supply of all material, labour T & P etc. required for proper completion of the work.

Supply of fixing of perforated pipes in filter media beds.

Rcc work 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size)

Brick work with F.P.S. bricks of class designation 7.5 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with F.P.S. bricks of class designation 7.5 in superstructure in Cement mortar 1:6 (1 cement : 6 coarse sand)

Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate) 40 mm thick finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.

P/F Flush door shutter with commercial ply vaneering on both faces. 35 mm thick

P/F MS Tee iron section for doors i/c cutting welding to required size,

15mm cement plaster in cement mortar 1: 4 ( 1 cement : 4 fine sand )

12mm thick cement plaster in cement mortar 1 : 6 ( 1 cement : 6 fine sand )

6 mm thick C.P. in C.M. 1:3 on ceiling

Applying oil bound distemper two or more coats

supply and fixing Truss work bottom cord,purlin,tie , compression member chord etc. complete

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.fixing with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with dash fastener or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.(MS works for door and windows etc. complete)

Providing and fixing factory made ISI marked steel glazed doors,windows and ventilators side /top /centre hung with beading and all members such as K11 B and K12 B etc.complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted with 15x3mm lugs, 10cm long, embedded in cement concrete blocks 15x10x10cm of 1:3:6 (1 cement:3 coarse sand:6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required

Fixing glass panes, with putty and nails wherever necessary 4 MM thick

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. (35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.)

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete (300mmx16mm)

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 125 mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete

250mmx10mm

150mmx10mm

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Twin rubber stopper

Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

White washing with lime to give an even shade: New work (three or more coats)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade (New work (two or more coats) over and including priming coat with cement primer)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ .90ltr/10 sqm)

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/ 10 sqm of approved brand or manufacture

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.T.M.T

Centring and shuttering including strutting,propping etc. and removal of form for

Columns, Pillars, Piers, Abutments, Posts and Struts.

Slab beams,& plinth beams

Suspended floors, roofs, landings, balconies and access platform.

Half brick masonry with F.P.S. bricks of class designation 75 in superstructure above plinth level in Cement mortar 1:4 (1 cement : 4 coarse sand)

Earth work in excavation by mechanical means (Hydraulic Excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete,including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.With cement mortar 1:4 (1 cement : 4 fine sand)

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete,including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-ChargeWith cement mortar 1:4 (1cement: 4 coarse sand)

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer -

Nominal concrete 1:3:6 or richer mix

Nominal concrete 1:4:8 or leaner mix

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge( In cement mortar)

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead

Of area 3 sq. metres and below

Of area beyond 3 sq. metres

Protection work

Excavation for foundation in Soil mixed with boulders

RR Stone Masonry 1:6 including supply of all materials, labour, T&P etc. complete

RR Dry including supply of all materials, labour, T&P etc. complete

PCC 1:2:4 including supply of all materials, labour, T&P etc. Complete

Provision of 1.5 m high Boundary Wall in brick masonry including supply of all materials, labour, T&P etc. complete at MPS and Top CWR campus.

Provision of Barbed Wire Fencing through angle iron posts around the water works site .at MPS and Top CWR campus.

Provision of Iron Gate with Pillars of sizes 3.6m wide complete.

Supply of all materials, labour, T & P etc. and dismatling & replacement of old waste water pipe line etc. complete

JAGAT SINGH