Special Repair to bldg No HT 06 OTM Accn at Tirah line Mil Stn Dharamsala

Amount

Taking down chowkats with shutters (without taking off shutters from chowkat) exc 1.50 Sqm but not exc 4.00 Sqm each complete all as specified and directed.

Taking down chowkhats without taking down shutters n exc 1.5 sqm each complete all as specified and directed.

Taking down cement plaster on brick or stone wall including raking out joints hocking for key scrubbing down with water etc.

Dismantling boarding, any description, fixed in any position with nails as in purlins, complete all as directed.

Dismantling timber scantling 40 Sq Cm and over in section in any position unframed work

Dismantling plain or corrugated steel sheeting, any gauge, thickness, in roof covering.

Demolition of cement Concrete is ground floors and pavings n exc 15 cm thickness (below or above ground level) including old polymeric membrane all as specified.

Demolition of Brickwork or stone/ boulder masonry, including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles built in cement mortar

Dismantling wall and ceiling board or insulation boards/ slabs/ blankets, any thickness, including cover fillets.

M&L 2nd class hard wood as in plain fillets rectangular, exc.15sq.cm but n.exc 25sq.cm in section, wrought, fixed with nails complete all as specified and directed.

M&L 2nd class hard wood in scantling, clean sawn, timber fixed.

S & F Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed using Iind class hard wood.

S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, one face is covered with decorative face veneer with lipping/frame to match.

S & F 30 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats using second class hard wood

S&F 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in square in exc 0.5 sq.m in each pane complte all as specified.

S&F for Butt hinges 75 mm long, medium weight, cold rolled mild steel, and fixed complete all as specified.

S&F for Butt hinges 100 mm long, medium weight, cold rolled mild steel, and fixed complete all as specified.

S&F aluminium alloy, anodised, sliding door bolt 250 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed

S&F for Aluminium, anodised, barrel tower bolt of 200mm long bolts of extruded section

S&F for Aluminium, anodised, barrel tower of 125 mm long bolts of extruded section and fixed

S&F for Aluminium, handle cast type anodised,150mm long all as specified and directed.

S&F for Aluminium, handle cast type anodised,125mm long all as specified and directed.

Rendering 20 mm thick on stone masanary wall or concrete surface in CM 1:6, in two coat of 10 mm each finished even and smooth without using extra cement.

Rendering 15mm thick on stone masanary wall or concrete surface in CM 1:4, finished even and smooth without using extra cement .

M&L 40mm th PCC 1:2:4 type B-1 using 20mm graded aggregate as in sub base finished even and rough to receive the topping layer.

Machine cut pre polished Kota stone slab flooring 20 - 25 mm thick, with border of 150mm wide16mm thick white marble, over and incl 20mm th screed bed in CM 1:3 cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

Ditto as per item no 26 but as in skirting over and incl 15mm thick rendering in cm 1:4 fair and even incl and taking down cement plaster on brick or stone wall including raking out joints hocking for key scrubbing down with water etc.. Complete all as specified and as direced

M&L for walling of random rubble, brought up to course, well bonded, bedded and solidly hearted, built in cm 1:6

Ditto as per item no 28 but except stone.

M & L for two coats of synthetic enamel paint over and incl a coat of pink primer on new wooden surfaces over 10 cm in width or girth including preparation of new or previously untreated surfaces of wood.

M & L for one coats of synthetic enamel paint on old wooden surfaces over 10 cm in width or girth including preparation of surfaces of wood.

M&L for prepairing newly plastered surface and two coats of Oil bound distemper over and incl a coat of primer incl preparation of surface. Complete all as specified and as directed.

S&F 0.63mm thick galvanised,corrugated mild steel sheeting with two corrugation side lap, fixed with L-type or J- type or cranked hook bolts and washers, in roofs, walls etc.

S & F 0.63mm Plain, black, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with self tapping screws as specified

S & F Bands, straps, supports or stays for rainwater, ventilating pipes,including bolts, if required:hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains;hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee pieceinserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165

M & L for PCC 1:2:4 type b-1 , in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones,bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

S&F anodised aluminium snap grid frame work of 605x605mm size for false ceiling all as specified and directed.

S&F hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

M & L 6mm thick non asbestos fibre cement building board fixed/inserted to timber/GI/Aluminium frame work ceiling flat or sloping

M & L complete removal of existing treatment from wall surfaces and applying two coats of distemper oil emulssion, white or tinted including clearcolle on surfaces for prepatory to distempering, complete all as specified.

M & L applying one coat of cement based paint on old decorated or undecorated wall surface including preparation of surfaces by washing rubbing down and stoping of distempered and painted surfaces complete all as specified.

M&L for applying one coat of synthetic enamel paint on old decorated steel surfaces exc 10 cm width or girth including preparation of surfaces , complete all as specified and directed

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings, tube light fittings etc removing material to store for keeping in safe custody or for taking credit ( credit for above items should be made as per conditions separately ) and also making good disturbed surfaces of wall, floors etc all as specified and as directed by the Engineer-in-Charge.

Material and labour for point wiring with 1.5 Sqmm copper conductor (Multi-stranded) PVC insulated and unsheating FRLS electric cable 1100 volts cable and including PVC casing and caping of suitable size (as per conductor run) with all fittings/ accessories and including PVC insulated electric cable 1100 volts 1.5 Sqmm ( multi-stranded) copper conductor single core( Green colour) cable as continuous earth wire connected to common earth dolly including sunk sheet steel terminal box made out of 1.6 mm thick MS sheet covered with 3 mm thick plastic laminated sheet ( Make Hylum) concealed in wall or on surface as per site requIrement and making good disturbed surfaces of wall for one light point/bell point/fan point/exhaust fan point etc controlled by one, one way switch complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 44 above, but for one 3 pin socket outlet 5 Amp on same board complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 44 above, but for one 3 pin socket outlet 5 Amp on independent board complete all as specified and as directed by the Engineer-in-Charge.

All as per serial item No 44 here-in-before , but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor ( Multi-stranded) PVC insulated and unsheating electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common earth dolly complete all as specified and as directed by Engineer-in-Charge.

Material and labour for socket outlet 2 in 1, 3 pin, 5A flush type complete all as specified and directed.

Material and labour for socket outlet 2 in 1, 3 pin, 5 Amp and 15 Amp flush type complete.

Material and labour for Switch piano flush type single pole one way 15 Amp complete

Material and labour for Switch piano flush button 5 Amps complete

Material and labour for ceiling rose surface type, 65 mm x 50 mm two to three terminals / PVC / polycarbonate, isolated body fixed on PVC block complete all specified and as directed by the Engineer-in-Charge

Supply and fixing (in replacement) for sub main wiring single core PVC insulated and unsheathed cable two run 6 Sqmm multi -strand copper conductor drawing in PVC casing caping with 1 x 4.0 Sqmm earth wire as in earth and neutral complete all as specified and directed

Supply & fix in replacement of existing unserviceable Sheet metal enclosure with DB’s suitable for MCBs of triple pole and neutral 4 way, 415 volt, double door type with 200 amp rated bus bar double door type with one incoming and 04 outgoing Note: i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble. ii) The disturbed surface shall be match with existing shall be part of job.Make:Havells/Legend/ Hegger

Supply and fix in replacement of MCB TPN/FP 63 Amp all as specified and directed. Make: ABB/Siemens/Hegger/Havells

Supply & Fix in replacement of existing unsrviceable Sheet metal enclosure for DB’s suitable for MCBs of single pole and neutral 8 way (Double door) with 200 amp 240 Volts rated bus bar all as specified. Note: i) Connections of MCB's shall be done with appropriate size of brass/Copper thimble. ii) The disturbed surface shall be match with existing surface.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and neutral, current carrying capacity 32 AMP, in the MCB DB Complete with connection testing and commissioning.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning.

Supply and fixing LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete

Supply and fixing LED street light fitting 15 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. Make : Havells or equivalent.

Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6.3mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 Metres below normal ground level, connecting to the Galvanised iron earth lead wire 4mm dia, by means of bolts, nuts, check nuts and washers of galvanised iron and 4mm earth lead protected by provision of GI medium grade pipe 15mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and with 6mm dia MS bar handle made to shape, GI medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of 75x50x6mm phosphorous bronze with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 3 of SSR-2009 Part-I and connecting to earth test point including testing on completion all as specified and directed by the Engineer-in-charge.

Excavating in trenches , n. exc. 1.5 mtrs wide and n. exc. 1.5 mtrs in depth in hard/dense soil and n.exc 1.5 m in depth and getting out all as directed.

Returing , filling ,including spreading , levelling, watering and well ramming including moundas as in hard/ dense soil in layers not exc 25 cm all as per directed.

Removing excavated materiel n.exc. 50 Mtrs and depositing where directed at a level n. exc. 1.5 mtrs above the strarting point in soil all as per directed.

M & L for Sand cushioning to underground cables complete all as specified in clause 19.75 of SSR Part-I (2009) laid before and after laying of cable complete all as specified.

M&L for old size sub class 'B' bricks laid in trenches as cable covers complete

Supply & laying XLPE insulated heavy duty electric power cables with multistranded aluminium conductor,1100 volts grade of size 25 sqmm 3.5 core complete all as specified and directed by Engr-in-Charge

Supply & fixing/ laying of GI pipe of size 40mm dia light grade laid in trenches/walls including clamps,screws etc… complete all as specified and directed by Engr-in-Charge

M & L for cutting of existing road/ floor/ plinth/drain for taking out/laying of UG cable through GI pipe including necessary earth work excavation and making good to match with existing surface complete all as specified with PCC 1:3:6 type C1 by (using 20mm graded stone aggregate) complete all as specified.

Krithvik Electricals (BID ID -3117597)

M/S MADAN GOPAL and CO (BID ID -3124949)

Ms Sunil Kumar (BID ID -3127765)