8452/E8 REPAIR AND MAINT OF SWIMMING POOL INSTALLATION, REPLACEMENT OF PARTS AND ALLIED WKS AND REPAIR AND MAINT OF MES INSTALLATION AT BAREILLY STN UNDER GE (EAST) BAREILLY

Amount

Taking down cement plaster including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons Laid, bedded and pointed in any mortar etc. complete all as specified and directed.

Demolition cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

Demolition concrete of any description and in any position not otherwise specifically provided cement concrete complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down shutter of any description exc. 1 sqm but n.exc 2 sqm each and removing from site complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in floors, surfaces finished fair and even complete all as specified and directed.

M&L 100 mm thick PCC 1:4:8, type D-2 (using 40mm graded stone aggregate) as in sub base floor / pavings complete all as specified and directed.

M&L for PCC Type B1 (1:2:4) for copings on brick wall surfaces/ interlocking paths /cherequred tiles including weathering, slightly rounded or chamferred angles and throating , as directed.

M&L 18 mm thick granite of black colour (table rubbed and polished) as in windows cill, in steps, jambs, pillars, cooking platforms and like in cement mortar (1:4) including form work, pointing in white cment (1:2) using marble dust with admixture of pigment to match with shade of granite with full round bull nosing edging complete all as specified as directed.

M&L for 75mm thick PCC 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed.

M&L in repairs for machine pressesd coloured glazed chequered cement concrete tiles 25cm thick Glossy finish with mixture of grey and white cement in equal proportions and no pigment set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over and including screed bed or bedding layer of mortar 20 mm thick, in cement mortar (1:6), complete all as specified and directed.

M&L in repairs for machine pressed pre-cast concrete interlocking coloured paver block, Glossy finish and shape and size conforming to IS-15658-2006 of 80 mm thickness M-40 grade with grey cement and pigment laid dry over and including 50 mm thick stone dust or sand base and compacted using vibrator complete all as specified and directed.

M&L in repairs for machine pressed pre-cast concrete interlocking coloured paver block, Glossy finish and shape and size conforming to IS-15658-2006 of 60 mm thickness M-40 grade with grey cement and pigment laid dry over and including 50 mm thick stone dust or sand base and compacted using vibrator complete all as specified and directed.

M&L in repairs for Machine pressesd pre-cast cement concrete 1:2:4, type B1 (using 20mm graded crushed stone aggregate) kerb stone 300 x 150 x 450mm including weathering, slightly rounded or chemferred angles and throating including excavation for kerb stone complete all as specified and as directed.

S&F Aluminium Composite (ALCO) panel exc 3 mm thick,jointed with screws ,cutting,edging,and grooves finished using epoxy silicon composite resin compound of any colour ,fixed on flat or curved surface incl aluminium strip 24 mm x38 mm complete all as spd and directed .

M&L for brick work with fly ash bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as spd as directed.

M&L rendering 15 mm thick in CM 1:6 on brick masonary wall surfaces or on other than fair faces of brick masonry finished without using extra cement complete all as specified and directed.

M& L for rendering 15mm thick in cement mortar (1:4),finished even and smooth using extra cement to on brick masonary wall surfaces or on other than fair faces of brick masonary finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 5 mm thick in CM 1:3 as on concerete surface on ceilings finished even and smooth without using extra cement complete all as specified and directed.

M & L for applying cement slurry over existing roof surface @ 3 Kg/Sqm inculding mix with water proofing liquid @ 0.15 ltr per 50 kg cement bags as per manufactures instructions complete all as specified and directed.

M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:4, over RCC roof slabs for laying water proofing treatment including mixed with using water proofing liquid @ 150 ml per bag of cement complete all as specified and directed. (Note for item No. 33 & 34: The Cost of Water proofing liquid shall be deemed to be included in this item)

supply Integral water proofing Liquid of Dr fixit/sika/Fosroc

S&F in repair 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specifed as directed

S&F for 35 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 35mm thick factory made glazed and skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain cham-fered or rounded, mitred and rebated sash bars, any numbers The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed by Engineer-in-Charge. (Note :- S & F wire mess shall be measured and paid for separately)

S&F 150 mm long floor door stopper of brass body and tongue with hard drawn steel spring complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing complete all as directed.

S&F 30 mm thick factory made both side Prelam PVC sheet used instead of Plain colour PVC sheet. Stile and rails feathered at edges consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F mild steel window grills box type framed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding complete FE-290 grade E-165 all as specified and directed.

S&F for steel windows / ventilators conforming to IS-1038 with side hung shutters including box type hinges with 2 Nos MS 100mm size tower bolt over MS flat iron for each openable leaf & Z section handle and steel peg stay complete without glazing bars, dovetailed or welded including one shop coat of Red Oxide Zinc chromate primer complete all as specified and directed by Engineer-in-Charge. (Note :- Wire cloth shall be measured and paid for separately).

S&F for steel windows conforming to IS-1038 with side hung shutters including box type hinges with 2 Nos, MS 100mm size tower bolt over MS flat iron for each openable leaf & Z section handle and steel peg stay complete with glazing bars, dovetailed or welded including one shop coat of Red Oxide Zinc chromate primer complete all as specified and directed. (Note :- Glass shall be measured and paid for separately).

S&F for steel ventilators fixed type, with glazing bars complete welded including one shop coat of Red Oxide Zinc chromate primer complete all as specified and directed. (Note :- Glass shall be measured and paid for separately).

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc. 0.5 Sqm in each pane complete all specified and as directed.

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc. 0.5 Sqm in each pane including Hacking out old, broken glass (any thickness,) size quality or description) from metal frames including punching or drilling out old glazing pins/spring clips complete all specified and as directed.

S&F stainless steel wire cloth, 0.56 mm nominal dia of wire and average with of aperture 1.18 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repair stainless steel wire cloth, 0.56 mm nominal dia of wire and average with of aperture 1.18 mm and fixed with stainless steel wire staples in m s window / wooden shutter complete all as specified and directed

S&F aluminium alloy powder coated aluminium door frame fixed with side hung shutters and glazing fixed with and including 5.50mm thick tinted glass fixed with rubber gasket with aluminium heading, clips frame made with aluminium box sec as appended below complete all as specified and directed (a) Frame 100x44x1.20mm thick with rawl plug (b) Middle/style rail : 85x44x1.20mm thick (c) Bottom/top rail : 114x44x1.20mm thick (d) Aluminium beading : 0.7mm thick (e) Aluminium handle D type 150mm long, aluminium tower bolt 9.9mm dia shoot 200mm long brass mortise lock 100mm 4 leaver aluminium stopper, cleat double action floor spring hydraulically regulated made of n.less than 1.25mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other part of steel heavy duty ( Make Sandhu marked or its equivalent approved make) (f) Making good of wall surface to match with existing surface complete.

M&L for repairing to existing aluminium doors of any size by straightening of frame / shutter, replacing the detoriated member with new, replacing the broken / non funcional hinges with new, replacing decayed rubber gasket with new, replacing the broken glass pane of any size with new 5.00mm thick tinted/ ordinary glass, replacing unserviceable handle, tower bolt, lock, floor spring, foundation box with governing pivot, top pivot, peg stay etc with new and including taking down and at same place after making the door / window smooth functional complete all as specified and directed.

S&F in repair PVC hollow interlocking wall paneling of 5mm thick prelam PVC sheet. The panel & strips shall be of 600 kg / cum density manufactured by an ISO-9000 certified company. The strips should two PVC strips. The PVC strip shall be fixed to the wall using 65mm long M.S screws through the groove in the strip by using PVC fasteners. The distance between two screws shall not be more than 200mm. The exact size of the panel and correspondingly of the grid may vary depending on the size of the wall. Optionally a strips of 5mm thick PVC sheet of width 75mm feathered at the edges shall be stuck at the places where two panels are joined, using solvent cement.

S&F 200 mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed completed all as specified and directed.

S&F 150 mm thick Aluminium, anodised, barrel tower bolts of extruded section and fixed completed all as specified and directed.

S&F 150mm size aluminium handles, cast type anodised completed all as specified and directed.

S&F 100 mm size butt hinges medium weight stailess steel colled rolled complete all as specified and directed.

S&F in repair 300mm, ordinary rat tail rod patttern springs includding roller and roller platewith fixed to wooden/pressed steel frame chowkats with flat iron 40x3mm size 75 cm long with necessary bolts, etc. complete all as specified and directed.

S&F 300 mm long mild steel sliding door bolts plate type stone enamelled black with bright bolt not less than 16 mm dia with and including a minimum of 6 bolts and nuts, 04 Nos on bolt plate and 02 Nos on staple plate and fix complete all as specified and directed

S&F in repair 300 mm long brass sliding door bolts without locking arrangement with screws in internal shutter of bldgs complete all as spd as directed

S&F rotational moulded polethylene water tank of 1000 ltrs capacity, ISI Marked (cylindrical vertical with closed top with suitable size of M S Tasla with suitable locking system) hoisted and fixed in position all as pacific SSR Part- I including dismantling of existing water tanks capacity n exc 1000 ltr complete all as specified and directed.

S&F rotational moulded polethylene water tank of 500 ltrs capacity, ISI Marked (cylindrical vertical with closed top with suitable size of M S Tasla with suitable locking system) hoisted and fixed in position all as pacific SSR Part- I including dismantling of existing water tanks capacity n exc 500 ltr complete all as specified and directed.

S&F 20mm bore ball brass valve high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed

S&F GI tube 15 mm dia medium grade with all fittings and fixed to wall, ceiling or laid in floors including taking down existing GI tubing 15 mm dia & connections complete all as specified and directed.

S&F GI tube 20 mm dia medium grade with all fittings and fixed to wall, ceiling or laid in floors including taking down existing GI tubing 20 mm dia & connections complete all as specified and directed.

S&F in repair 20 mm dia stainless steel 1.0 mm thick fancy type droppery rod with decorative design matching brackets as approved and knobs (lattu) or end bracket as required incl fitting with 80 mm long SS screw with 75 mm long wooden gitty of appropriate c/s in each end & intermediate support complete all as specified and as directed

S&F in repairs, vitreous China wash hand basin, white, flat back size 550 x 400mm including 15mm dia pillar tap , 450 mm long HDPE PVC connection, 750 mm long 32mm bore HDPE waste down pipe including Stainless steel brackets all as directed.

S&F in repairs 15 mm dia bib tap fancy type chromium plated with flange quarter turn complete all as specified as directed. Model : FUS 29037 Fusion of Jaquar, Parryware model No G2304A1, Cera model No F101151

S&F in repairs 15mm bore PVC connections, with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repairs of 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as spd as directed

S&F in repair fancy type chromium plated brass angle valve type suitable for 15mm bore pipe complete all as specified. Model : ARI -39053 of Jaquar,Hindware Model No F320006, Parryware Model No G4907A1

S&F in repair vitreous china squatting pan of orrissa pattern long pan size 580 x 440 mm white with "P"or "S" trap size 100 mm dia front or back inlet and integral foot rest any pattern (excluding flushing cistern and flush pipe) including provn of lime concrete bedding complete all as specified. Make Hindware / parryware or equivalent as approved by GE

S&F in repairs, PVC low level cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed. Model: Sleek fresh dual flush of Hindware Model No Pastel size 47.6x15.5x32 , Parryware Cat No 8177*, Cera Cat No B1810110 snow white"

S&F in repairs, vitreous China bowl urinal flat back size 430x370x340 with grating and union for discharge pipe excluding flushing cistern flush pipe and waste pipe complete all as specified and directed.

S&F in repair PVC (SWR) multifloor trap with grating including jointing with solvent cement floor trap 75 mm dia outlet plain with grating including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as specified and directed.

S&F in repair PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fitting complete all as specified and directed.

S&F in repair PVC (SWR) 110mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fittingcomplete all as specified and directed.

S&F PVC (SWR) 110mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75mm bore bends any radius complete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1979 complete all as specified and directed

S&F Pre-coated galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified.

S&F 0.50 mm plain galvanised Mild steel sheeting in ridge, hips, valley gutter,drip and straight flashing class 8 with zink coating @ 120 gms/sqm fixed with L- type or J- type or cranked hooks bolts complete all as specified and directed.

M&L for cutting chases of hanging chajjas, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of sunshades, shelves, lintels, Chajja (up to IInd floor) etc making good, cutting out exc 10cm and not exc 40cm girth in RCC chajjas in brick walls complete all as specified and as directed.

S&F for 0.71mm thick Aluminium plain sheeting Alloy 31000 H4, STUCCO Embossed finish with fixed with coach screw and Aluminium washer in roof and wall etc. with end laps stitched with 25x6mm G.I. bolts at 20cm apart incl dismantled also complete all as specified and as directed.

S&F Framed work as in doors, gates & Stairs of angle or other section with gusset plates, rails, braces, etc., complete,drilled for fixing of steel sheeting or other covering to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and fastening and fixing FE 290 Gde E-165 complete all as specified and as directed.

M&L repair of existing iron gates/ rolling shutters i.e. welding of any size , fixing/refixing of hold fast ,repair/replacement of iron sheet of any size/thickness or any repairable damages including painting , fixing the same in existing position complete all as spd and directed .

M&L for 10mm thick rendering in cement mortar 1:3 on fair faces of concrete surfaces with water proofing compound 3% wt of cement of RCC overhead reservoir (Max height 24 mtr) in any position and finish the surface even and smooth without using extra cement complete all as specified and directed.

M&L for pressure washing and cleaning thoroughly the bottom floor and inside walls of swimming pool after draining out of water including cleaning of joints of tiles of the pool by suitable mechanical means using mild hydrochloric acid for fungus /algee free surfaces including removing all dirt and foreign matters if any from the pool to a distance not exceeding 50m complete to the satisfication of the Engineer-in charge all as spd and directed . Note:-(a) Size of the swimming pool is 50m lengthx21m width and depth varrying from 1.2m to 3m(Approx).(b) Draining of water from the swimming pool shall be made by the department.

M&L for pressure washing and cleaning thoroughly the bottom floor and inside walls of swimming pool after draining out of water including cleaning of joints of tiles of the pool by suitable mechanical means using mild hydrochloric acid for fungus /algee free surfaces including removing all dirt and foreign matters if any from the pool to a distance not exceeding 50m complete to the satisfication of the Engineer-in charge all as spd and directed . Note:-(a) Size of the swimming pool is 16m lengthx16m width and depth 5m (Approx).(b) Draining of water from the swimming pool shall be made by the department.

M&L for preparation of old plastered or un plastered surface of concrete , walls, of RCC Over Head Reservoir (Max height 24 mtr) capacity 100000 Glns) cornices etc by brooming down or steel wire brushing scrapping down smoke soot , moulds moss and efflorescent salts and trading oil and greasy spots including all necessary scaffolding and applying two coat of two coats of Dust Resistant and Anti Algal weather proof exterior emulsion paints over a coat of primer . complete all as specified and directed.

M&L for preparation of old plastered or un plastered surface of concrete , walls, of RCC Over Head Reservoir (Max height 24 mtr) capacity 50000.00 Glns) cornices etc by brooming down or steel wire brushing scrapping down smoke soot , moulds moss and efflorescent salts and trading oil and greasy spots including all necessary scaffolding and applying two coat oftwo coats of Dust Resistant and Anti Algal weather proof exterior emulsion paints over a coat of primer . complete all as specified and directed.

M&L for preparation of old plastered or un plastered surface of concrete , walls, of RCC Over Head Reservoir (Max height 24 mtr) capacity 35000.00 Glns) cornices etc by brooming down or steel wire brushing scrapping down smoke soot , moulds moss and efflorescent salts and trading oil and greasy spots including all necessary scaffolding and applying two coat of two coats of Dust Resistant and Anti Algal weather proof exterior emulsion paints over a coat of primer . complete all as specified and directed.

M&L for preparation of old plastered or un plastered surface of concrete , walls, of RCC Over Head Reservoir (Max height 24 mtr) capacity 25000.00 Glns) cornices etc by brooming down or steel wire brushing scrapping down smoke soot , moulds moss and efflorescent salts and trading oil and greasy spots including all necessary scaffolding and applying two coat of two coats of Dust Resistant and Anti Algal weather proof exterior emulsion paints over a coat of primer . complete all as specified and directed.

Removal of complete beehive of RCC Over Head Reservoir (Max height 24 mtr) including all necessary scaffolding complete all as specified and directed.

Removal of vegitation growth trees (any dia) complete with complete roots including application anti grroth chemical from RCC roof slab rain/ sewage water pipe complete including of brick / concrete masonry if required , scaffolding at any height and making good with and including materials as demolished , including matching with existing surface complete all as specified and directed.

M&L preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed.

M&L for complete removal of existing treatment on walls etc including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and applying two coats of oil bound distemper over 1mm thick cement based in double layer wall care putty complete all as specified and directed.

M&L for preparing newly plastered walls surfaces and applying two coats of oil bound distemper over 1mm thick (JK/Birla) wall care putty complete all as specified and directed.

M&L for preparing old plastered walls surfaces and applying one coat of oil bound distemper complete all as specified and directed.

M&L for preparing old plastered surfaces and applying two coats of white wash on ceiling complete all as specified and directed.

M&L for preparing newly plastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed.

M&L for preparing newly plastered walls surfaces and applying two coats of cement base paint over one coat primer complete all as specified and directed.

M&L for preparing old plastered surfaces on walls etc including cleaning of any mortar drops, fungus efflorescent salts etc and applying one coats of cement based paint complete all as specified and directed.

M&L for preparing old plastered surfaces on walls etc including cleaning of any mortar drops, fungus efflorescent salts etc and applying one coats of white wash complete all as specified and directed.

M&L applying two coats of Apex paint over a coat of primer on old decorated or undecorated Roof/Wall surfaces/jaffery including preparation by brooming down or steel wire brushing, scrapping down, brushing, washing rubbing down and stoping of distempered and painted surfaces, complete all as specified and directed.

M&L Machine cut kota stone flooring , tread/riser 16-18 mm thick over 20 mm thick screed bed laid in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing and treating the surface complete complete all as specified and directed by Engr-in-charge

Dismantling of old fencing any type of mesh and size completed all as specified and directed.

Dismantling of posts or struts(wood steel or RCC) any section including taking out embedded portion and making good disturbed natural ground completed all as specified and directed.

M &L PCC (1 :3:6) type B1 using 40mm agg as in post holes in CM 1:6

S&F Angle iron fencing post and struts including cutting tops to shape as directed drilling holes, notching for wire etc, flat iron fillets (for securing wire mess etc) including all necessary drilling, bolting or riveting etc and similar work conforming to Fe 410-0 or Fe 310-0 including round bars etc complete all as spd & directed.

Fixing only chain link fencing including line wire any mesh size and type of standards raills, starining bolts ewtc including provisioning of binding wire complete all as spd & directed .

Supply only chain link MS galvanised fencing any size or type complete all as spd & directed .

Mild steel screw bots (machine made ) with hexagonal or square heads at one end and screwed the other each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 10 cm but not exc 15 cm and 15mm dia complete all as spd & directed..

Lifting/taking out defective submersible pump of any capacity alongwith column pipe of any size and submersible cable, dismantling the pump from motor, setting aside for repair /servicing / overhauling including lowering the pump set into borewell replacement of packing and nut bolts (if required) and testing after the completion of repair works in the presence of JE/ Engr in charge .

Disconnections of electric connection of the starter of 3/5/12.5/15/25 HP Pumping set for repairs installed at LT Panel in the pump house, carefully checking the parts throughly & replacement of unseviceable parts such as electronic Motor Protection relay with inbuilt earth fault protection, Over load protection relay ranging 16 -100Amp, MNX-16-100 contractor, NO-NC for starter, (Front add on auxilary contact block) and electronic timers multi time setting type, 240/415 Volt, 50 Hz of range, complete all as specified & directed. Make- L &T / Havells/Minilec. Note :- Spare parts to be measured and paid seperately in respective items.

Dismantling the submersible pump assembly capacity 12.5/15 HP completely, checking and segregating serviceable / unserviceable parts, cleaning serviceable parts thoroughly by approved method, replacement of wron out parts, stage casing, pump shaft, impeller, key, bearings , bowl bush NRV, nut, bolts and other minor parts etc including necessary lath / machinery work including all new parts as reqd, re-assembling the pump completely lowering the pump alongwith all accessories to the existing location, overhauling, commissioning, testing and connecting up complete including painting all as specified and directed.

Dismantling, cutting and removing the burnt windings from the submersible motor of capacity 12.5/15 HP, rewinding with suitable size / gauge of super enameled / copper conductor and other approved insulating materials, heating, drying and replacement of existing size of submersible cable including varnishing, overhauling, reassembling the motor, installing, commissioning, testing and connecting up complete all as specified and directed.

Supply only of following parts suitable for ser item No 115.00 for Submersible motor :-

(a) Oil Seal Set

(b) `O` ring set

(c) Motor bearing Bush set

(d) Complete Pad set (Bearing assembly)

(e) Rotor sleeve set

(f) Thrust plate with ferredo lining

(g) Upper/Lower bearing house

(h) Balancing ring

Dismantling the submersible pump assembly capacity 3.0/5.0 HP completely, checking and segregating serviceable / unserviceable parts, cleaning serviceable parts thoroughly by approved method, replacement of wron out parts stage casing, pump shaft, impeller, key, bearings , bowl bush NRV, nut, bolts and other minor parts including necessary lath / machinery work including all new parts as reqd, re-assembling the pump completely lowering the pump alongwith all accessories to the existing location, overhauling, commissioning, testing and connecting up complete including painting all as specified and directed.

Dismantling, cutting and removing the burnt windings from the submersible motor of capacity 3/5.0 HP, rewinding with suitable size / gauge of super enameled / copper conductor and other approved insulating materials, heating, drying and replacement of Seal, O ring, bearing, bush thrust plate, etc existing size of submersible cable including varnishing, overhauling, reassembling the motor, installing, commissioning, testing and connecting up complete all as specified and directed.

Disconnections of electric connection of centrifugal pump and motor capacity of 25/20 HP, lifting and removing motor form its existing foundation to the location (in side/outside of building) where directed by the Engr-in-charge. Dismantling the pump and motor of capacity 25/20 HP, carefully checking, segregating serviceable and unserviceable parts, cleaning the serviceable parts thoroughly by approved method (Pats like stator, rotor, terminal box, bearings shaft, key etc) heating, drying & varnishing including replacement of burnt winding for 25/20 HP motor with super enameled copper wire of existing gauge and good quality of insulating materials including replacement of unserviceable parts as required including necessary lath / machining work. Reassembling the pump and motor including painting with two coats of synthetic enamel paint after necessary surface preparation, marking of number (SM, MES or srl No) installing to its existing foundation, commissioning, connecting up and testing complete as directed. Note:- Spares shall be measurded and paid separately under respective items.

Disconnections of electric connection of centrifugal pump and motor capacity of 12.5 HP, lifting and removing motor form its existing foundation to the location (in side/outside of building) where directed by the Engr-in-charge. Dismantling the pump and motor of capacity 12.5 HP, carefully checking, segregating serviceable and unserviceable parts, cleaning the serviceable parts thoroughly by approved method (Pats like stator, rotor, terminal box, bearings shaft, key etc) heating, drying & varnishing including replacement of burnt winding for 12.5 HP motor with super enameled copper wire of existing gauge and good quality of insulating materials including replacement of unserviceable parts as required including necessary lath / machining work. Reassembling the pump and motor including painting with two coats of synthetic enamel paint after necessary surface preparation, marking of number (SM, MES or srl No) installing to its existing foundation, commissioning, connecting up and testing complete as directed. Note:- Spares shall be measurded and paid separately under respective items.

Supply only of following parts suitable for ser item No 120.00 for centrifugal pump and motor completed all as specified and directed.

(a) 25/20/12.5 HP Pump Bearing No 6310 or suitable size

(b) Pump bearing seat suitable for 3 ph 25/20/12.5 HP motor

(c) Motor side cover suitable for 3 ph 25/20/12.5 HP motor

(d) Motor connected plate six hole suitable for 3 ph 25/20/12.5 HP motor

(e) 25/20/12.5HP Motor Bearing No 6308 or suitable size

(f) 25/20/12.5 HP Motor Bearing No 6309 or suitable size

M&L for Dismantling the Sewage pump set up to 5 HP, carefully checking, segregating serviceable and unserviceable parts, cleaning the serviceable parts thoroughly & including replacement of unserviceable parts as required (Block piston, Nozzle, head block, cupling engine parts & Impaller, gland packing, Pump shaft, pump seal Pump parts) including necessary lath / machining work. Reassembling the pump and engine parts including painting with two coats of synthetic enamel paint after necessary surface preparation, marking of number (SM, MES or srl No) & replacement of unserviceable suction & Delivery PVC pipe, flange, clamps, foot valve etc and testing complete as directed.

Supply and fixing DI fittings for Flanged pipe, DI Bends, connecting pieces, bell mouth pieces, tapers, tee pieces of one end flanged and other end spigot or socket upto 150 mm bore complete all as specified and directed.

M & L for construction of brick masonry valve pit of size 90x90x90cm (internal dimension) one brick thick wall built in CM (1:4) on 100mm thick PCC (1:4:8) type D2 (using 40mm graded crushed stone aggregate) as in foundation, and 15mm thick rendering in cement mortar (1:4) both externally and internally, external plaster shall be up to 15cm below GL, providing valve pit cover made of 3.15mm thick MS sheet/plate, including provision of hinges, handle and locking arrangement including 40 X 40 X 5mm angle iron frame fixed on top of valve pit by means of MS hold fast 40x5mm and 150mm long, embedded in PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) including two coats of anti-corrosive paint over a coat of red oxide zinc Chrome primer and necessary earth work in soft/loose soil including demolition of old unserviceable existing valve pit & pit cover complete all as specified & directed.

S&F CI Non Return Sluice Valve flanged ends of class 1.6 PN, size 150mm bore including taking down old existing unserviceable Non Return Valve complete all as specified and directed.

S&F CI Non Return Sluice Valve flanged ends of class 1.6 PN, size 100mm bore including taking down old existing unserviceable Non Return Valve complete all as specified and directed.

M&L for repairs to leaking joints for CI/DI pipe, spigot and socket pipes and fittings, of following sizes of bore in water mains, by burning out old lead joints in position including provision of run lead and including necessary excavation and earht work complete all as specified and directed.

(a) Bore of pipe 150 mm

(b) Bore of pipe 100 mm

(c) Bore of pipe 80 mm

Supply and fix Green & Red button operated push type, Star Delta Starter Oil mersed with Single Phase Preventer, Type designation BSA, Operatig current 18Amp, coil voltage 380 _+15% , 3 phase 415V 50 Hz suibtable for 5.0/7.5 HP Submersible Pump and Motor complete with Over load tripping circuit (Max relay (14-20 Amp), Reverse phasing , unbalancing, Low voltage , high voltage upto motor terminal and starting time delay and should be housed in Dust proof, Moisture proof and powder coated sheet metal fabricated box with locking arrengement with extra long life contact with arrengement including taking down of existing starter complete all as specified and directed . Make- Kapil SKN or equivalent

Supply and fix Green & Red button operated push type, Fully automatic Star Delta Starter with Single Phase Preventer, Type designation BSA, Operatig current 18-25Amp, voltage 380 _+15% , 3 phase 415V 50 Hz suibtable for 12.5/15 HP Submersible Pump and Motor complete with Over load tripping circuit (Max relay (14-20 Amp), Reverse phasing , unbalancing, Low voltage , high voltage upto motor terminal and starting time delay and should be housed in Dust proof, Moisture proof and powder coated sheet metal fabricated box with locking arrengement with extra long life contact with arrengement including taking down of existing starter complete all as specified and directed . Make- Kapil SKN or equivalent

Supply and fix Green & Red button operated push type, Fully automatic Star Delta Starter with Single Phase Preventer, Type designation BSA, Operatig current 18-25Amp, voltage 380 _+15% , 3 phase 415V 50 Hz suibtable for 12.5/15 HP Submersible Pump and Motor complete with Over load tripping circuit (Max relay (14-20 Amp), Reverse phasing , unbalancing, Low voltage , high voltage upto motor terminal and starting time delay and should be housed in Dust proof, Moisture proof and powder coated sheet metal fabricated box with locking arrengement with extra long life contact with arrengement including taking down of existing starter complete all as specified and directed . Make- Kapil SKN or equivalent

Supply and fix DOL starter three phase 415 volt 50 Hz push button type suitable for 05/7.5 HP centrifugal pump set with arrangement and making the necessary connection in panel and pump set including taking down of existing starter complete all as specified and directed. Make- L&T or equivelent as approved by GE

M&L for Painting to pipe of Swimming pool plant /pump house rising mains, header, valves, pipe, fittings, NRV, discharge head etc after cleaning, scrapping and making the surfaces free from rust of main externally and painting with two coats synthetic enamelled paint in black / blue / red including marking / writing on pipe etc complete as specified and directed

Supply , install, testing and commissioning robotic 6th sense swimming pool cleaner suitable for cleaning pool floor, walls upto 2100 Sqft in 2 Hrs,, filter 18000 Ltr per hr smart Z programming, suitable for any pool shape, surface and type can climb upto 6 Ft, saves 93% energy and 30% pool chemical, remote control for specific cleaning, 4 strong scrubbing wheel, 2 powerful motors, 100 Ft long cable with 360 degree swivel with 2 year comprehensive warranty complete all as specified Make : Milagrow or equivalent approved by Engr-in-charge/GE

M&L for providing technician for attending any breakdown of swimming pool equipment and machinery as per requirement and directed by Engr-in-charge for fixing the issue on site and making the plant functional including repair and replacement of minor parts of starter, motor, plant etc

M&L for trimming vegetation or small inequalities clearing all grass vegetation, saplings, shrubs, brushwood, roots, and tree of surroundings area up to 500 sq mtr including cleaning and removing rubbish upto a distance of 50 mtr outside the periphery of the area under clearance of water supply installations complete all as specified and as directed.

M&L for providing and lowering, connecting submersible pump set 5 to 15 HP during the unserviceability of existing pump set including connecting pipe cable etc as per site requirement

Supply & fix in repair 1100 volts grade heavy duty cable PVC insulated aluminum conductor screened served with inner sheathing of PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 meter apart including 4mm GI suspension wire, one twin core cables flat or circular of size 10 Sqmm etc complete all as specified and directed.

S&F in repair Off load change over switch 200 Amp, 4 pole, 415 Volts, 50 Hz, complete all as specified and directed

M&L for Earthing complete with using GI earth plate electrode 600x600x6.0 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 mtr below normal ground level and earth plate surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness off 15 cm all around the plate with using GI Strip 25 x 4mm as earth lead moulded and retreived to earth plate at one end and connected to main switch / control board at another end with and including 15 mm dia GI light grade from upper end of earth plate upto external face of the wall of the building including 20 mm dia bore GI pipe light grade as water pipe from chamber to upper edge of the plate GI funnel with wire mess fixed on water pipe and provison of PCC 1:2:4 type B-1 (Using 20 mm Dia graded stone aggregate) duly reinforced with mild steel round bar 6 mm dia @ 150 mm c/c both ways with 10 mm dia mild steel bars as in lifting handle with and including necessarry excavation and earth work including laying the pipe concealed in floor / wall allas per plate NO-3 of SSR Part-I complete all as specified and directed and testing on completiopn (Note:- If the desired resistance is not found earthing shall be done by the contractor at no extra cost to Govt).

M & L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 25 x 4mm galvanised iron strip, complete all as specified and as directed.

Supply and Fixing of suction strainer for 25HP pump set of size 200mm all as specified and directed.

S & F in repairs of MCB TPN DB 4 Way, (4+12) suitable for flush mounting and surface mounting, conforming to IP 43 - IK 09 with acrylic door with 100 Amp copper bus bar for each phase, complete with din rail, Neutral and Earthing bar after taking out the old unserviceable DBs, connection complete and making good the disturbed surfaces complete all as specified and as directed.

S & F in repairs of DX3 AC MCB SP, 240 Volt, 6 to 32 Amp, 10 KA, ISI Marked, "C" Curve, IP 20 Protected terminals, Complete all as specified and as directed.

S & F in repairs of DX3 AC MCB TPN, 415 Volt, upto 63 Amp, 10 KA, ISI Marked, "C" Curve, IP 20 Protected terminals, Complete all as specified and as directed.

Supply only Calcium based granularhypo chlorite 65% to 70% disinfectant for water treatment, Packing in 45 Kg, plastic drums complete all as specified and directed.

M&L MCCB 4 pole, 415 Volt, fixed type 125 to 160 amp with breaking capacity 25 Ka complete all as specified and directed.

M&L MCCB 4 pole, 415 Volt, fixed type 160 to 200 amp with breaking capacity 25 kA complete all as specified and directed.

M&L MCCB 3 pole, 415 Volt, fixed type 63 to 100 amp with breaking capacity 16 Ka complete all as specified and directed.

Supply and fixing in repairs PVC pressure hose pipe upto 10 to 20Kg/cm2 as per existing size, complete all as specified and directed.

S&F in repairs Digital multi programmable electronic timer capacity for 24 hrs clock, 3 phase, 415 volts, 50 Hz, complete all as specified and as directed.

S&F in repairs electronic Single phase preventer operation on 415 volts 50 Hz all as specified and as directed.

M & L for Grass and weeds killer chemical 5 Ltrs capacity of make Roundup, complete all as specified and directed.

S&F LT rubber mat of size 1.0mx2.0mx12 mm at water supply installations, complete as specified and directed.

S&F pressure gauge of dial 0 to 14Kg/cm2, suitable for fixing at MS pipe 100/150/200 dia header with all fiting and fixtures etc, complete as specified and directed.

S&F over load protection relay suitable for 5HP to 25HP monoblock/centrifugal /submersible motors of make L&T all as specified and directed.

Supply and fix in repair MNX contactor 16Amps to 40Amps, 3 Pole with No and NC complete all as specified and directed. Make : L & T.

Supply and fix in repair MNX contactor 63Amps to 100 Amps, 3 Pole with No and NC, complete all as specified and directed. Make : L & T.

Supply and fix in repair spare kit for MNX contactor 16Amps to 100 Amps, 3 Pole, complete all as specified and directed. Make : L & T.

S&F in replacement of PVC bib tap 15 mm.bore, complete all as specified and directed

S&F in replacement MS ERW column pipe screwed 100 mm nominal bore having wall thickness not less than 7.11 mm electric resistance welded with MS flanged 16 mm thick heavy duty confirming to IS 6392 incl 2 mm thick rubber sheet and steel nuts and bolts 10 mm long with washer etc, complete as specified and directed.

(a) 150 mm nominal bore.

(b) 200 mm nominal bore.

(c) 300 mm nominal bore.

Take the water sample from the bore well at PH No.38 (Stn swimming pool) & JRC Swimming pool and send it for physical / Chemical / Bateriological test from any recognised govt agency and provide its report to Engr in charge.

S& F in replacement submersible pump/motor 15HP, Electric driven, 415 Volts, TP suitable for bore well, Output dia- 80 mm, Head 60 Mtr, 1400 LPM, Vertical type, complete all as specified and directed. Make:-CRI / KSB / KIRLOSKAR

S& F in replacement submersible pump/motor 3 HP, Electric driven, 415 Volts, TP suitable for Well/ Semi UG Sump, Head 70-90Mtr, 2250 LPM, Horizontal type, complete all as specified and directed. Make:-CRI / KSB / KIRLOSKAR

S& F in replacement Monoblock self priming HI-Flow pump/motor 01/02 HP, Electric driven, 230 Volts , SP suitable for 25/20mm dia output, Head 70-90 Mtr, 120-150 LPM, complete fitting/fixtures with starter panel, complete all as specified and directed. Make:- CRI, KSB and KIRLOSKAR.

Supply fixing testing and commissioning submersible cable flat 10.0 sqmm x 3 core PVC insulated and PVC sheathed with multi stranded copper conductor 1100 volts grade fixed to submersible motor column pipe using suitable size of clamps made out of stainless steel flat of size 20x2 mm with steel nuts bolts & washer foe every column pipe of 3 mtr lenght all as specified and directed.

(a) 6.0 sqmm x 3 core..

(b) 4.0 sqmm x 3 core..

(c) 2.5 sqmm x 3 core..

Supply, install, testing and commissioning of Mild steel chlorine gas cylinder suitable for 100Kg capacity with filling lequid chlorine gas, industrial type as manufacturer recommended pressure for usage of drinking water treatment for improving taste, safety and odour of drinking water, highly reactive, reliable, optimum quality to kill Bacterial organisms at public properties, complete all as specified and as directed.

Supply, install, testing and commissioning of Remote wall/floor panel mounted Vacuum Chlorinator (regulator) for reduces the gas from a varying supply pressure 10kg- 75kg capacity with safety kit complete set suitable for disinfection of water through gravity feed, Vaccum feed or motor feed chlorination by main water supply/swimming pools/sewage water treatment etc, complete all as specified and directed.

S&F in repair of teflon pipe 6mm internal dia. and 10mm outer dia complete all as specified and as directed.

Supply, installation, Commisioning and testing for Chemical dosing system metering type, capacity to deliver 14- 27 LPH max & adjustable from 10% to 100% through Knob and suitable to inject against 5-10Kg/cm2 pressure duly operated by 240V, Single phase power supply, Chemical Solution preparation tank of 200 Ltrs capacity made out of FRP (made with Bisphenol resins) having port hole on lid for pouring chemical, water inlet connection, overflow and drain with valve, outlet connection with PP ball valve for transferring solution to chemical dosing tank of 100 Ltrs capacity made out of FRP (made with Bisphenol resins) having port hole on lid, inlet connection and tank lid duly mounted with agitator made of Stainless Steel -316 operated with single phase FHP electric motor for dissolution of chemical, dising pump shall be complete with inlet /outlet check valves, strainer cum foot valve and tubing for suction/delivery injection line including fittings etc, complete all as specified and as directed Make : Declibac Modle :-96 NGQ51, Item NR:- DPP9651 or Equivalent in poter & Watt Crop/Briozing Unlimited.

Supplying, installing, commissioning & testing of cast iron body butterfly valves of size 200 mm capacity 10 Bar and PN.1.0 rating and per BIS 13095:1991 with fresh rubber gaskets , bolts and nuts Butterfly vlaves all as specified and directed.

Supplying, installing, commissioning & testing of cast iron body butterfly valves of size 100 mm capacity 10 Bar and PN 1.0 rating and per BIS 13095:1991 with fresh rubber gaskets, bolts and nuts Butterfly vlaves all as specified and directed.

Repair/Maintenance of Swimming Pool and other allied works M&L for complete overhauling and repairing of pressure filter capacity 2500 Cu M/hr including removal of chocked media from filter and depositing same with 30 m from plant room, scraping and cleaning of filter inside surfaces and re-painting with 3 black bituminous pant, cleaning of lateral pipes and recharging each filter with fresh filter media as follow :- i. Natural graded gravel of size 25mm - 20 mm : 150 mm layer: 68 Cu Ft ii. Natural graded gravel of size 15mm - 10 mm : 100 mm layer: 45 Cu Ft iii. Natural graded gravel of size 10 mm - 6 mm : 100 mm layer: 45 Cu Ft iv. White graded coarse quartz sand 8 + 14 mesh : 100 mm layer: 45 Cu Ft v. White graded coarse quartz sand 16 + 30 mesh: 600 mm layer: 22 Cu Ft vi. Cleaning and repairing of under wash system including renewal of broken/defective unserviceable strainer/nozles. vii. Replacement of man holes & hand holes gaskets, painting exterior surface with synthetic enamel of approved shades viii. Scraping cleaning / making internal and external shell of filteration plant neat and tidy and painting internal surfaces with two coats of anti corrosive black bituminous lead free paint over a coat of primer and externally with two coats of synthetic enamel paint over one coat of primer with sprayers and wiritng description of filteration plant complete all as specified and directed.

M&L for soda ash as directed by Engr in Charge

M&L for Bleaching powder as directed by Engr in Charge

M&L for copper sulphate as directed by Engr in Charge

M&L for Alum Crystal as directed by Engr in Charge

M&L for dismantling of non clog type centrifugal pumping set of capacity 5/7.5 HP either fixed on floor or on trolley mounted and taking out unserviceable spares and performing following operation to complete the task :-(a) rewinding of motor centrifugal pumping set with insulated copper winding wire including sleeves as per original company and replacement of worn out parts, including grinding & polishing of rotor sleeves and refixing, testing & transport charges complete all as specified & directed. (b) replacement of motor bearing with lock nut -02 Nos. (c) replacement of fan motor-01 No. (d) replacement of star couling set with rubber -01 each. (f) replacement of impellor with key -01 No (g) replacement of gland coupling -01 No

De watering of well up to 26' feet deep and up to 8 mtr dia by portable pumping set and taking out manually waste material like sludge,mud,soil,sanitory material and other dirts etc from inner sump and outer housing sump by using labour/equipment and depositing the same waste material at low lying area by digging pits all as, Cleaning and washing the surface area of sump well with wire brush and removing the algae growth including removal of grass/tree roots inside sump and above surrounding area etc all as specified and directed .

S&F in repair sluice valve class PN-1.6 heavy duty flanged ends drilled ISI marked confirming to IS: 14846 suitable for 150 mm bore pipe, wheel operated (Handle) with high tensile stainless steel spindle, including nuts, bolts and jointing with jointing materials etc. complete including taking out old existing unservicable sluice valve including making arrangement for safe working all as specified and directed. Make: BIR, KIRLOSKAR, Kartar

S&F in repair sluice valve class PN-1.6 heavy duty flanged ends drilled ISI marked confirming to IS: 14846 suitable for 100 mm bore pipe, wheel operated (Handle) with high tensile stainless steel spindle, including nuts, bolts and jointing with jointing materials etc. complete including taking out old existing unservicable sluice valve including making arrangement for safe working all as specified and directed. Make: BIR, KIRLOSKAR, Kartar

Supply & Replacement suction sweeper , head 24 to 36mtr long with trolly mounted type including suitable pump, suction/delivery hose of suitable size , Brush and connected items complete all as specified and as directed & after dismantling the unserviceable one.

S&F foot valve of size 100 mm bore complete all as specified & directed.

S&F foot valve of size 80 mmbore complete all as specified & directed.

S& F Chlorine test kit of standard size for to check daily Chlorine as directed.

Supply only O-Tolodine regent solution in 500 ml bottle as per Sample approved complete all as specified and directed.

Taking down the chlorine plant of make as per existing plant from chlorine cylinder, opening it to detecting fault and repiar / replacement of unserviceable parts, overhauling and refixing the same after completion of job including testing complete all as specified and as directed. Note :- Repair/Replacement of unserviceable parts will be measured and paid under relevent items

S&F in repair of following parts of Chlorine Plant complete all as specified and as directed.

(a) Vaccum regulator and measuring glass with 'O' ring set.

(b) Inlet valve

(c) 'O' ring set for measuring glass

(d) Clamping ring

(e) Valve body

(f) Wate pressure gauge round type 75mm dia. Suitable for 6 to 10 kg/cm2 pressure

(g) Valve cap

(h) Ball guide

(j) Spring support

(k) Filter

(l) Presssure spring

(m) Valve seat

(n) Set screw

(o) Adjust screw upto 200 gms /hr glass

(p) Diaphragm disc

(q) Ring diaphragm

(r) Main chlorinator diaphragm

(s) Yoke clamp assembly for chloronome plant

(t) Main diaphram with plate assembly

S&F in repair of nylon braided PVC pipe 25mm bore heavy duty complete all as specified and as directed.

S&F in repair of following parts of ejector assembly of Chlorine Plant complete all as specified and as directed.

(a) Ejector nozzle pressure feed

(b) Ejector diaphragm assembly

(c) Ejector spring assembly

(d) Ejector diaphram nut

M&L for cleaning the swimming pool by draining out the water and removing the debris and cleaning the wall and surface of swimming pool by scrapping using tile cleaning brush, pool safe chemical to remove stains from from wall and floor or hight pressure washer to scrub the wall and floor and draining out the water using suction sweper or vaccum cleaner heavy duty , and finally rinsing the surface with clean water using pressure washer and draining out the water and debris all as directed by Engr-in-charge

S&F swimming pool skimmer net , heavy duty swimming pool leaf rake with deep fine nylon mesh net bag with stainless steel bristles hogard telescopic pole extendable upto 20 Feet

Supply only chlorine Gas safety mask ideal for protection against chlorine gas

Supply and fixing in replacement of PVC suction currugated hose pipe with flanged ends of green colour of bearing capacity 2500 Pa, temperature range 0deg-100deg and velocity 30-40 m/s of foloowing size all as specified and directed by Engr-in-Charge.

(a) 25 mm bore

(b) 50 mm bore

(c) 80 mm bore

URBANS CONSTRUCTIONS (BID ID -3461685)

Vishal Traders (BID ID -3461748)