Construction of New I.T.I.(Industrial Training Institute) Building at Dindoli Dist. Surat

Construction of New I.T.I.(Industrial Training Institute) Building at Dindoli Dist. Surat

BILL OF QUANTITIES

Percentage Rate Tender

Item Description of Item Quantity Unit Rate In Amount

1 Excavation for foundation upto 1.5 m depth 2695.00 Cumt 123.13

including sorting out and stacking of useful

materials and disposing off the excavated stuff

upto 50 Meter lead.(A) Loose or soft soil

2 Excavation for foundation for depth from 1.5 m 1274.00 Cumt 170.50

to 3.0 m including sorting out and stacking of

useful materials and disposing off the

excavated stuff upto 50 Meter lead.(B)

Dense or Hard soil

3 Excavation for foundation from depth 3.00 m to 386.00 Cumt 184.77

5.00 m including sorting out and stacking of the

useful materials and disposing off the excavated

stuff up to all lead. (A) Dense or Hard soil

4 Filling in foundation and plinth with sand in 642.00 Cumt 481.80

layers of 20 cm. Thickness including watering

ramming and consolidating etc. comp.

5 Filling available excavated Earth (Excluding 2063.00 Cumt 136.92

Rock) in trench plinth side of foundation . in layer

not excluding 20 cm in depth consolidation each

deposited layer by ramming and watering etc.

6 Filling foundation and plinth with murrum or 1407.90 Cumt 301.78

selected soil in layer of 20 cm in thickness

including ramming watering and consolidating

Item Description of Item Quantity Unit Rate In Amount

7 Anti Termite System 1864.00 Sqmt 134.33

P/L of Permenent piping technology Anti Termite

treatment before flooring work by installing

LLDP (Low linear density Polyethylene) tube of

mm O.D.& 6.4 mm I.D.With in Built Pressure

Compenstaion chif every 30 cm interval in the

tube, having working pressure of 2 kg/cm 2 and

realese rate of 1.9 ltr/Hour fixed by P-Clip and

nails . The LLDP pipe shall be installed at the

entire periphery of the building and at internal

network of building depth of 20 to 200 mm

under floor every 2 to 3 mtr.c/c distance

(adjustble as per building layout ) & Ends of loop

pass through a PVC Elbow of minmum 32 mm ID

at junction box of wall and floor level, entring

into a steel reinforcmed grooved flexible pipe

mini.22 mm LD leading into junction box and

during injecting chemicls for termite control

tretment. The anti-termite chemical Lmidcloprid

30.5% SC Mix as per IS 6313(part-III) shall be

injected by the pressure pump diluted with water

@ 10.5 ml/5ltr of water at the rate of

kg/sq,cm.@ 5 ltr /Smt .the contractor shall

submit approved line plan for piping system and

junction boxes dully approved By Engineer -in-

charge with bond of 5 Years warnty .

8 Providing and laying controlled cement concrete 250.00 Cumt 3958.25

M.150 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work in (A) Foundations and

9 Providing and laying controlled cement concrete 847.00 Cumt 4678.32

M.250 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work in (A) Foundations,

footings, and Mass concrete. footing

10 Providing and laying controlled cement concrete 111.00 Cumt 7912.34

M-250 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

(d) columns Up to Plinth level.

11 Providing and laying cement concrete 1:3:6 (1- 134.00 Cumt 3095.25

Cement : 3- coarse sand : 6- machine cut stone

aggregates 40 mm nominal size) and curing

complete excluding cost of formwork in (A)

Foundation and Plinth

Item Description of Item Quantity Unit Rate In Amount

12 Providing and laying controlled cement concrete 204.10 Cumt 7884.06

M-200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Columns, pillars posts and struts G.FLOOR &

13 Providing and laying controlled cement concrete 26.00 Cumt 7925.47

M-200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Columns, pillars posts and struts S.FLOOR

14 Providing and laying controlled cement concrete 352.00 Cumt 6445.82

M-250 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Ground & Plinth BEAMS

15 Providing and laying controlled cement concrete 311.00 Cumt 5657.01

M.200 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work in (C) Plinth Slabs

16 Providing and laying controlled cement concrete 555.00 Cumt 6307.45

M.200 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work in (C) Ground floor

Beams, & First floor Beams,

17 Providing and laying controlled cement concrete 4.00 Cumt 6348.86

M.200 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work in (C) S floor Beams,

18 Providing and laying controlled cement concrete 41.50 Cumt 6930.62

M-200 and curing etc. complete including the

cost of form work and reinforcement for

reinforced concrete work in (c) Chhajja for

Ground floor &Chhajja for First floor

19 Providing and laying controlled cement concrete 1.00 Cumt 6972.03

M-200 and curing etc. complete including the

cost of form work and reinforcement for

reinforced concrete work in (c) Chhajja for

20 Providing and laying controlled cement concrete 24.00 Cumt 6978.09

M-200 and curing etc. complete including the

cost of form work and reinforcement for

reinforced concrete work in (c) Lintal for Ground

floor & Lintal for First floor

21 Providing and laying controlled cement concrete 1.00 Cumt 7019.50

M-200 and curing etc. complete including the

cost of form work and reinforcement for

reinforced concrete work in (c) Lintal for Second

Item Description of Item Quantity Unit Rate In Amount

22 Providing and laying controlled cement concrete 528.00 Cumt 6732.66

M.200 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work in (C) Ground floor

Slab & First floor Slab

23 Providing and laying controlled cement concrete 7.00 Cumt 6774.07

M.200 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work in Second Floor slab

24 Providing and laying controlled cement concrete 15.00 Cumt 7263.92

M-200 and curing etc. complete including the

cost of form work and excluding the cost of

reinforcement etc. complete in (E) Stair case for

Ground Floor to first floor to Second Floor

25 Providing and laying controlled cement concrete 4.00 Cumt 10530.26

M-200 and curing etc. complete including the

cost of form work and excluding the cost of

reinforcement etc. complete in RCC Vertical and

horizontal wall for S.floor

26 Providing and laying 8" thick Ironite flooring in 1057.00 Sqmt 1432.18

C:C (M-200) laid in 1st layer of 188 mm thick &

2nd layer of Ironite material 2 kg/m² of 12mm

thick mixing with ratio of 1:4 with dry cement

finished with 3 phase Trimax floater disc incl.

material, labour and as per following method

incl. expansion joint at 30 mt. c/c as per

instruction Method of Ironite mixing : Mix well

Ironite & cement in dry condition & take one part

by volume of the above mixed material and two

volume of grit 6mm to 2mm size & mix well in

dry condition the grit should be of hard stone

clean & without dust. Add water 80 liter to

liter (Ration 0.4 to 0.45) water should be clean

portable & non Acidic. Method of before laying :

Surface of the graynplythic layer must be rough

and without water on the surface. At the time of

laying : Initial setting i.e. if ceases the thumb

impression control of quantity of water take care

to see the Ironite is mixed properly and evenly in

the mix. After laying : See that it is properly

leveled after formal setting of flooring keep the

are of the flooring under water for 8 to 10 days

before use and necessary instruction by

Architect. Machine mixed and floater Dish

finished Ironite (200 mm. thick concrete mixture

machine and vibrator is compulsory)

Item Description of Item Quantity Unit Rate In Amount

27 Providing and fixing 90 cm high Stainless steel 60.00 Rmt 3603.68

railing made from anticorrocive 304 grade S S

pipe of 50 mm dia (16Gauge) as hand rail with S

S 304 grade Baluster of 38 mm dia (16Gauge) as

a vertical support fixed in RCC slab at 1.2m c/c

including three horizontal S S pipes of 25 mm

dia (16Gauge) at eqal distance fixed by 18.75 mm

dia (16Gauge) S S pipe with baluster including

accessories as per detailed drawing as directed

28 Providing IS Mark TMT FE 550D bar 388744.00 Kg 95.04

reinforcement for RCC work including bending &

placing in position complete up to All floor Level

29 Providing and fixing eco-friendly light weight 1204.00 Sqmt 1674.15

calcium silicate false ceiling tiles having Tegular

edge & 15 mm Thick Densified edges on the Tile

Periphery for Extra Strength The Light weight

calcium silicate ceiling tiles shall have, light

reflection 85% non-combustible as per B.S.

part IV, 100% humidity resistance and also

having thermal conductivity0.043° w/m KC.for

the best thermal Insulation. The Light weight

calcium Silicate tile shall be of approved texture

Fine fissured/ Spintone/ Cosmos having NRC

value of 0.5 & Globe having NRC value of

NRC or equivalent of size 595 X 595 mm to be

laid on true horizontal level suspended inter

locking metal grid of hot dipped galvanized steel

sections (galvanizing @120 grams per sqm

including both side) consisting of main ‘T’ runner

suitably spaced at joints to get required length

and size of 24 X 38mm made from 0.30 mm thick

(minimum) sheet, 1200mm centre to centre, and

cross ‘T’ of size 24 X 28mm made out of 0.33mm

(Minimum) sheet spaced 1200mm along spaced

between main 'T' at 600mm centre to centre to

form agrid of 1200x600mm and size 24x48mm

made of 0.30mm thick (Minimum) sheet to be

interlocked at middle of the 1200x600mm panel

to form grid of size 600x600mm resting on

periphery walls/partitions on a perimeter wall

angle pre-coated steel of size (24x24x3000mm

30 Brick work using common burnt clay building 333.00 Cumt 4214.33

bricks having crushing strength not less than

kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:5. (1- Cement : 5 -fine sand)(B)

Conventional below plinth

31 Brick work using common burnt clay building 938.00 Cumt 4487.43

bricks having crushing strength not less than

kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:5. (1- Cement : 5 -fine sand)(B)

Conventional {Ground FLoor} and {First FLoor}

Item Description of Item Quantity Unit Rate In Amount

32 Brick work using common burnt clay building 93.00 Cumt 4545.47

bricks having crushing strength not less than

kg./Sq.Cm. in super structure in Cement Mortar

1:5. (1- Cement : 5 -fine sand)(B) Conventional

33 Half brick masonry in common brunt clay 1503.00 Sqmt 685.83

building bricks having crushing strength not less

than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1-

Cement : 4 -coarse sand ) in foundation and

plinth (B) Conventional in super structure. for

ground floor. and First froor

34 Providing, fabricating, and fixing Glass 222.00 Sqmt 5488.34

Reinforced Concrete (GRC) jali of approved

design and pattern, factory-cast using M25 grade

cement concrete with alkali-resistant (AR) glass

fibre (minimum 5% by weight of cement), fine

aggregates, polymer additives, and admixtures.

The jali shall be of minimum 30 mm thickness or

as specified, with smooth moulded finish, free

from defects or deformities. The jali shall be fixed

in position using stainless steel (SS)

brackets/clamps or mechanical anchors, with

non-shrink grout or polymer-modified

cementitious adhesive as per manufacturer’s

specification. The rate includes design approval,

moulding, de-moulding, curing, transportation,

handling, scaffolding, installation, joint filling,

cleaning, and finishing, complete in all respects

as per drawings and direction of Engineer-in-

35 Providing and fixing 75x25 M.S. Box grill with Rat 219.00 Sqmt 1793.76

Mesh for all ventilator including necessary nails

or fixing material etc. complete.

36 Providing 15mm thick cement plaster in Double 11450.00 Sqmt 207.35

coat on Rough (Similar) side of single or half

birck walls / concrete wall for interior plastering

and finished even in C M 1:4 (1 cement : 4 coarse

sand) including Mala troweled finish etc. comp.

For Ground floor and first floor

37 Providing 15mm thick cement plaster in Double 509.00 Sqmt 231.92

coat on Rough (Similar) side of single or half

birck walls / concrete wall for interior plastering

and finished even in C M 1:4 (1 cement : 4 coarse

sand) including Mala troweled finish etc. comp.

For Second floor

38 Providing 10 mm. Thick cement plaster in Double 3718.00 Sqmt 190.11

coat for plastering on ceiling and soffits of stairs

and finished even and smooth in : (I) Cement

mortar 1:4 (1 cement : 4 sand) including Mala

troveled finish etc. complete.Ground Floor And

Item Description of Item Quantity Unit Rate In Amount

39 Providing 10 mm. Thick cement plaster in Double 155.00 Sqmt 214.68

coat for plastering on ceiling and soffits of stairs

and finished even and smooth in : (I) Cement

mortar 1:4 (1 cement : 4 sand) including Mala

troveled finish etc. complete. Second Floor

40 20 mm Thick sand faced Double coat Gutka 6575.00 Sqmt 347.42

plaster on walls with 1x1cm grooves consisting

of 12 mm Thick backing coat of c.m. 1:3 (1

cement : 3 sand) and 8 mm Thick finishing coat

of c.m. 1:1 (1 cement : 1 sand) etc. complete. For

all height and as per pattern sample aprroved by

the architect or directed engineer in-charge

41 Providing throating or plaster drip and moulding 606.00 Rmt 43.74

to R.C.C. Chhajja.

42 Applying two coats of Birla or Asian acrylic lapy 15341.00 Sqmt 40.59

(putty) & two coats of primer of approved brand

and manufacture on new wall surface to give an

even shade including thoroughly brushing the

surface free from mortar dropping and other

foreign matter and sand papered smooth.

43 Wall painting (two coats) with plastic emulsion 11377.00 Sqmt 83.36

paint of approved brand and manufacture on

undecorated wall surface to give an even shade

including throughly brushing the surface free

from mortar droppings and other foreign matter

and sand papered smooth.

44 Wall painting (two coats) with plastic emulsion 3964.00 Sqmt 89.04

paint of approved brand and manufacture on

undecorated ceiling surface to give an even shade

including throughly brushing the surface free

from mortar droppings and other foreign matter

and sand papered smooth.

45 Wall Painting (Two coats) with weather proof 6586.00 Sqmt 120.26

100 % acraylic emulsion (Apex or equivalent

type) paint of approved brand and manufacture

and of required shade on exterior wall surface to

give an even shade over and including primery

coat with Alkaly resistance primer of approved

brand after thoroughly brushing surface to

remove all dust and remains of loose powdered

material etc. copm. for all height

46 Providing And filling with good quality 89.00 Cumt 509.04

cinder(steam coal) as directed by engineer in

charge in sunks in layers of 15 cm thick,including

watering,placing ,ramming well etc as directed,

Item Description of Item Quantity Unit Rate In Amount

47 Providing and laying controlled cement concrete 49.05 Cumt 6483.19

M-200 for RCC work and curing complete

including the cost of form work but excluding the

cost of reinforced concrete work in coping on

Ground Floor and first Floor

48 Providing and laying controlled cement concrete 10.00 Cumt 6524.60

M-200 for RCC work and curing complete

including the cost of form work but excluding the

cost of reinforced concrete work in coping on

49 Providing and fixing a three-track sliding window 293.00 Sqmt 4421.88

made of standard extruded color-anodized

aluminum sections, equivalent to Series C (20

mm), with section numbers: shutter top -

shutter bottom - 20529, shutter interlock -

20531, shutter side (handle) - 20544, frame

bottom with gutter - 21651, and frame top & side

- 21650. The window shall be fitted with 5mm

thick transparent tinted float glass in each

shutter, secured with rubber gaskets, air lock

strips, and finished with silicone sealant for

airtight installation. The window will include

standard extruded color-anodized aluminum-

coated fittings as per design, ensuring durability

and smooth operation. The scope includes all

materials, labor, and necessary hardware for

complete installation as per the directions of the

Engineer-in-Charge

50 Providing and fixing two track Sliding window 30.00 Sqmt 5204.83

having standard extruded colour anodized

aluminum section equivalent to jindal series C

(30 mm) section numbers are : shutter top/side

21675 , bottom- 20772, shutter inter lock -

20550, frame-bottom with gutter- 20878, frame

top & side – 20877 with 5 mm thick transparent

tinted float glass in shutter as well as fix glass top

of window & Providing and fixing Nylon

Mosquito net with stitching on wall as per

window size, with rubber gasket, air lock strip

and finishing joints with silicon sealant, with

standard extruded colour anodized aluminum

coated fittings as per details etc complete.

51 Providing & Fixing in position standard extruded 19.00 Sqmt 2955.97

approved colour anodised Aluminum Ventilator

with outer frame 63.50 x 38.10 x 1.95 mm (of

Jindal Section No.4605,@ Wt 1.094 kg/Rmt )

with 3mm thick Bajari figure adgesteble tinted

louvers glass fixed to alluminium strip blade

including fixtures, fastenning, labours and

equipments as per detailed drawing as directed.

For Ventilators

Item Description of Item Quantity Unit Rate In Amount

52 Providing and fixing M.S. Collapsible steel 394.00 KG 111.10

shutters with vertical channels 20 x 10 x 2 mm

braced with flat iron diagonals 20 x 5 mm size

with top and bottom rails of T_rin 40x 40 x 6 mm

with 38mm dia, steel pulleys complete with bolts,

nuts, locking arrangements, stoppers handles

including applying a priming coat of red lead

paint with Fixed Ventilation, 3mm glass design of

which is to be approved by the architect or

directed by engineer in charge.

53 Providing and fixing 35 mm thick Double flush 44.00 Sqmt 4262.20

door shutter, solid core with Anodized

Aluminium section (jindal door section no 19552-

weight not less than 1.1 kg/mt ) frame size

63.5mm x 38mm inserted Non teak wood frame

inside the aluminium section for durable grip of

hinges & Double shutter with required

teakwood batten having 1mm thick lamination

on both side, Durable Grip shall be providing

with both side 15cm long stainless steel handle

and necessary Locking system of Godrej, ,S.S.

fixtures & fastenings etc. directed by engineer in

54 Providing and fixing 35 mm thick single flush 65.00 Sqmt 4016.77

door shutter, solid core with Anodized

Aluminium section (jindal door section no 19552-

weight not less than 1.1 kg/mt ) frame size

63.5mm x 38mm inserted Non teak wood frame

inside the aluminium section for durable grip of

hinges & single shutter with required teakwood

batten having 1mm thick lamination on both side,

Durable Grip shall be providing with both side

15cm long stainless steel handle and necessary

Locking system of Godrej, S.S. fixtures &

fastenings etc. directed by engineer in charge.

55 Providing and fixing FRP frame size 100 x 50 mm 54.00 Sqmt 2362.39

and 35 mm thick FRP depress panel single or

Double shutter having extra reinforcement on

sides & edges in Gel coat finish.The core of the

both shutter & frame is to be filed up with

injected fire retradat grade polyurethene foam

done in situ along with embeded wooden pieces

for stiffening & also taking hinges & fintures.The

whole FRP frame & single or double shutter is to

be waterproof, weatherproof ,termite proof &

resistance to mild acid/alkali.Rates are to be

inclusive of S.S hinges with necessary screws &

alluminum fixtures & fastenings & fartener

sleeve.Colour and Shade approved by Engineer-

Item Description of Item Quantity Unit Rate In Amount

56 Providing and fixing rolling shutters of approved 133.00 Sqmt 3554.40

make made of 80 mm wide M.S. laths inter-

locked together through their entire length and

jointed together at the ends by end locks

mounted on specially designed pipe shaft with

bracket plates, guide channels and arragements

for inside and outside locking with push-pull

operation including the cost of hood cover and

spring etc. complete.(A) Shutters having width

57 P & L 41x57 cm Machine polished Machine cut 658.00 Sqmt 1110.75

Blue Kota Stone slab flooring over 20 mm

(average)thick base of cement mortar 1:6 (1-

cement 6-coarse sand) or L.M 1:1.5 (1 Lime putty

: 1.5 coarse sand laid over and jointed with grey

cement slurry mixed with pigment to match the

shade of slab including rubbing and polishing

etc.complete (A) 30mm thick

58 P & L 41x57 cm Machine polished Blue Kota 35.00 Sqmt 1130.79

Stone slab 30 mm thick in riser of steps,skirting

dedo and pillars laid on 10 mm thick cement

mortar 1:3 (1-cement 3-coarse sand) and jointed

with grey cement slurry mixed with pigment to

match the shade of slab including rubbing and

polishing etc.complete (30 mm thick)

59 P & L 60x60 cm' GVT vitrified with 10 mm thick 798.00 Sqmt 1671.55

tile flooring over 20 mm (average)base of cement

mortar 1:6 (1cement : 6 coarse sand) on new

surface or fixing on existing flooring by adhesive

materials including dismentalig of existing

flooring and jointed with colour cement slurry

including groving of perifery of tiles with

required diammention & finished with flush

pointing and cleaning the surface etc. complete

60 Providing & Laying 60x60 cm Polished vitrified 711.00 Sqmt 1708.92

8 mm thick tile (soluble salt) flooring over

mm (average) base of cement mortar 1:6 (

cement: 6 coarse sand) on new surface or fixing

on existing flooring by adhesive material

including dismentaling of existing flooring and

jointed with color cement slurry including finised

with flush pointing & cleaning the surface etc.

complete shade approved by directed engineer in-

Item Description of Item Quantity Unit Rate In Amount

61 P & L 60x60 cm GVT charged vitrified 10 mm 107.00 Sqmt 1581.66

thick tile in risers of steps,skirting Dedo and

pillars laid on 10mm thick cement mortar 1:3 (1-

Cement : 3 coarse sand) and jointed with colour

cement slury mixed with pigment to match the

shade including groving of perifery of tiles with

required diamention & finished with flush

pointing and cleaning the surfaceetc. complete

62 P & L antiskid ceramic tiles 30 x 30 cm size 6 419.50 Sqmt 960.42

mm thick in flooring treads of steps and landing

laid on a bed of 12 mm thick cement mortar

1:3(1-cement:3-coarse sand)finishing with flush

pointing in white cement

63 P & L glazed tiles tiles size 30 x 60 cm 6 mm 373.00 Sqmt 1513.28

thick in skirting risers of steps and dedo on

mm thick cement plaster 1:3 (1-cement:3coarse

sand) and jointed with colour cement slurry

64 Providing and laying machine-cut, free-edge, 69.00 Sqmt 3448.14

machine-polished granite stone (18 mm thick)

for finished treads and risers, including 1 cm

projected nosing with rounded moulding in

treads, laid over 12 mm average thick cement

mortar 1:6 (1 cement : 6 coarse sand) for treads

and 10 mm average thick cement mortar 1:3 (1

cement : 3 coarse sand) for risers; jointed with

grey or coloured cement slurry, including

rubbing, polishing, and making three grooves of

size 3 mm × 3 mm along the length of each tread,

complete in all respects.

65 Providing and fixing pre-cast Rubber Dye / steel 1246.00 Sqmt 706.92

Dye inter locking concrete block 60mm thick

with grade of concrete M300 pnumatic

compressed / vibrated mechanically and as per

approved design Confirming to IS 15658 :

including 35 mm Sand layer for levelling and

filling the joint with sand in proper line and level

as per guidlines of IRC : SP 63-2018 etc.

66 Providing and laying water proofing treatment 1865.00 Sqmt 779.70

with broken chine mosaic flooring for terrace

using 12 mm to 20 mm broken pieces of glazed

tiles to be laid over cement mortar 1:3 to plain or

slope and to be tempered to bring mortar creme

out upto surface using white cement including

rounding off junctions and extending them upto

15 cm along the wall, clearing with water and

oxalic acid etc. as directed.

67 Providing and laying cement concrete flooring 1865.00 Sqmt 374.14

1:2:4 (1-cement : 2-coarse sand : 4-graded stone

aggregate 20mm nominal size) laid in one layer

and finished with a floating coat of neat cement.

(B) 50mm thick.

Item Description of Item Quantity Unit Rate In Amount

68 Providing Plinth Protection to Building including 400.00 Sqmt 1452.58

excavation in ordinary soil and laying cement

concrete 1:3:6 using stone aggregates of 40mm

nominal size in foundation layer 100 mm thick

below pre-cast Rubber Dye inter locking concrete

block 60mm thick with grade of concrete M200

pneumatic compressed by mechanically pressed

and as per approved design including 75mm

Sand layer for levelling and filling the joint with

sand in proper line and level etc. complete,

Including Providing and fixing pre-cast concrete

kerb stone of grey cement based concrete block

30cm length, 30cm height and 15cm thick of

M250 grade concrete as per approved design and

including excavation for fixing in proper line and

level, filling the joint with C:M 1:3 (1cement:3

fine sand) etc. complete.

69 Providing and fixing mirror polished 18 mm 456.00 Sqmt 2563.38

thick Green Marble stone with full round edge

and polished of approved quality in clading on

sill and around the doors/ windows/ ventilation

with 12 mm thick cement mortor CM (1:3) and

fixing with cement slurry & adhesive including

moulding of exposed edges as directed by

engineering in charge etc. complete.

70 Providinfg and fixing Safty grills of required 13472.00 Kg 112.82

pattern for windows/ Door using necessary M.S

angle/ M.S pipe, M.S flats and other structural

steel at required spacing including cutting,

welding and fabriction etc. including one coat of

primer of approved quality and two coats of oil

painting as per detail drawing etc complete.

71 Providing erecting and fixing double coated 15000.00 ltr 3.95

Syntex PVC. (ISI) water tank of required capacity

each with all necessary fittings and connection

etc. complete on terrace.

72 Providing laying and jointing in true line and 110.00 Rmt 195.67

level 50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold

water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as

approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every

two metre C/C or shall be concelled as directed

including necessary fittings etc. including testing

of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

Item Description of Item Quantity Unit Rate In Amount

73 Providing laying and jointing in true line and 120.00 Rmt 148.12

level 40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold

water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as

approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every

two metre C/C or shall be concelled as directed

including necessary fittings etc. including testing

of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

74 Providing laying and jointing in true line and 200.00 Rmt 91.84

level 25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold

water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as

approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every

two metre C/C or shall be concelled as directed

including necessary fittings etc. including testing

of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

75 Providing laying and jointing in true line and 140.00 Rmt 72.65

level 15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold

water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as

approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every

two metre C/C or shall be concelled as directed

including necessary fittings etc. including testing

of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

76 Providing, laying and jointing in true line and 180.00 Rmt 834.38

level 160 diametre U.P.V.C (Type B) conforming

to IS 13592-1992 with one end plain and other

end socketed with rubber ring, & fittings

conforming to ISI 14735-1999 of approved make

for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant,

pipe shall be fixed on wall using of PVC clamp of

the size 160 mm diametre x 210 mm length x

196 mm heigh at every 2000 mm center to center

or shall be concealed in walls as directed

including necessary fittings such as bends, shoes

etc. including testing of pipes and joints and

jointed with adhesive solvent cement including

cost of all materials.

Item Description of Item Quantity Unit Rate In Amount

77 Providing laying (to level or slopes) and jointing 506.00 Rmt 678.02

reinforced concrete Light duty non-pressure

pipes I.S. class NP2 of the following internal

diameter with collars and butt ends prepared for

collar joints including testing of joints

78 Providing, laying and jointing in true line and 442.00 Rmt 878.57

level 110 diametre U.P.V.C (Type B) conforming

to IS 13592-1992 with one end plain and other

end socketed with rubber ring, & fittings

conforming to ISI 14735-1999 of approved make

for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant,

pipe shall be fixed on wall using of PVC clamp of

the size 110 mm diametre x 149 mm length x

145 mm heigh at every 2000 mm center to center

or shall be concealed in walls as directed

including necessary fittings such as bends, shoes

etc. including testing of pipes and joints and

jointed with adhesive solvent cement including

cost of all materials.

79 Providing, laying and jointing in true line and 90.00 Rmt 292.90

level 75 mm dia. UPVC SWRType B pipe

conforming to IS 13592-1992 with one end plain

and other end socketed with rubbering and

fitting conforming to ISI 14735-1999 of

approved make for drainage system pipe line,

pipe shall be jointed with each other with rubber

lubricant, pipe shall be fixed on wall using of PVC

clamp at every 2000 mm c/c or shall be conceled

in walss as directed including necessary fittings

such as bends, shoes etc. including testing of

pipes and joints and jointed with adhesive

solvent cement including cost of all materials.

80 Providing and fixing in PVC SWR cowel went 6.00 No 15.66

75mm dia to pipes.(B) 75mm dia.

81 Providing and fixing in PVC SWR cowel went 14.00 No 28.79

110mm dia to pipes.(B) 110mm dia.

82 Providing and fixing PVC SWR Nahni trap IS 34.00 No 599.64

14735 for drain - 100 mm diameter with jali of

the following nominal diameter of self cleansing

design with C.I scread down or hinged grating

including the cost of cutting and making good the

Item Description of Item Quantity Unit Rate In Amount

83 Providing and fixing wash down water closet 18.00 No 3003.74

(European type W C pan) with integral P and S

trap including jointing the trap with soil pipe in

cement mortar 1:1 (1 cement five sand) including

providing and fixing plastic seat cover for wash

down WC with CP brass hinges and rubber

buffers back plastic seat and including providing

and fixing PVC flushing tank with a pair of C I or

MS bracket with complete fitting such as lead

valve siphon 15 mm dia brass ball valve with

polythene float CP brass handle unions and

couplings for connection with inlet out let and

over flow pipes 40 mm dia porcelain enameled

flush bend including cutting holes in walls and

making good the same connection the flush bend

with cistern and closet vitreous china.

{Hindustan, Cera, Parryware or equivalent }

84 Providing and fixing stainless steel grab 22 cm x 8.00 No 1492.78

60 cm for handicapped toilet

85 Providing and fixing brass screw down stop 15.00 No 205.83

tap.(A) 15mm dia.

86 Providing and fixing ball cock of approved. 4.00 No 189.84

quality as directed.(A) Copper Metal (ii) 50mm

87 Providing and fixing washbasin with single hole 14.00 No 1697.13

for pillar tap with C.I. or M.S. brackets painted

white including Rubber plug, sutting holes and

making good the same but excluding fittings and

also including rate of C.P. brass waste for

washbasin or sink (A) 32mm dia. and M.I. fisher

union for washbasin or sink. (A) 32mm dia.; (A)

Vitreous China:(ii) Flat Back washbasin 550 mm

x v 400mm size. (i) In white colour.

88 Providing and fixing 600mm x 450mm bevelled 14.00 No 859.41

edge mirrror of superior glass mounted on 6mm

thick A.C. sheet or plywood sheet and fixing to

wooden pluge with C.P. brass screws and

89 Providing and fixing C.P. brass towel rail comlete 12.00 No 616.42

with C.P. brass brackets fixed to wooden plugs

with C.P. brass scews (B) 600mm x 20mm size.

90 Providing and fixing screw down bib taps of 35.00 No 214.81

following size.(A) Brass screw down bib tap

polished bright. (i) 20mm dia.

91 Providing and fixing pillar tap, capstan head, 14.00 No 308.73

screw down high pressure with screws, shanks

and back nuts. (i) 15mm dia.

92 Providing and fixing in position 300 mm high, 60.00 No 308.73

150 mm wide English letters made from 1.0 mm

thick stainless steel sheet as directed by Engineer

in charge with all necessary tools & plants etc.

Item Description of Item Quantity Unit Rate In Amount

93 Providing and fixing Urinal of approved quality 6.00 No 1640.22

including connection with trap and with integral

longitudinal flush pipe.(A) Squating plate pattern

white earthenware 550mm x 300mm.

94 Providing and fixing chromium plated brass half 30.00 No 263.77

trun flush cock of approved quality including

fixing in pipe line etc. complete (ii) 25mm dia.

95 Providing and fixing S.W. gully trap with C.I. 12.00 No 1246.92

grating brick masonry chamber and water tight

C.I. cover with frame of 300mm x 300mm size

(inside) with standard weight (i) Square mouth

traps (B) 150mm x 100mm size P or R type

96 Constructing brick masonry chamber for 20.00 No 2288.66

underground C.I. Inspection chamber and bends

with briocks having croshing strength not less

than 35Kg. Cm2 in C.M. 1:5 precast RCC cover

455mm x 610mm intenal dimensions with frame

(R.C.C. top slabe with 1:2:4 mix (1-cement :2-

coarse sand :4-graded stone aggregate 20mm

size) foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement on

walls and bed concrete etc. complete (i) Inside

dimensions 455mmx 610mm and 450mm deep

for single pipe line.

97 Constructing brick masonry chamber for 20.00 No 2495.71

underground C.I. Inspection C.I. Inspection

chamber and bends with briocks having croshing

strength not less than 35Kg. Cm2 in C.M. 1:5

precast RCC cover 500mmx 700mm intenal

dimensions with frame (R.C.C. top slabe with

1:2:4 mix (1-cement :2- coarse sand :4-graded

stone aggregate 20mm size) foundation concrete

1:5:10 inside plaster 15mm thick with cement

mortar 1:3 finished smooth with a floating coat of

neat cement on walls and bed concrete etc.

complete (i) Inside dimensions 500mmx 700mm

and 450mm deep for single pipe line.

98 Extra over items for every additional depth of 10.00 No 242.39

0.1M. of part thereof beyond 450mm depth for

Brick masonry chamber.(i) for 455mm x 610mm

99 Extra over items for every additional depth of 10.00 Each 264.86

0.1M. of part thereof beyond 450mm depth for

Brick masonry chamber.(i) for 500mm x 700mm

100 Providing cement vata (10cm x 10cm size) 312.00 Rmt 24.28

quarter round in cement mortar 1:1 including

neat cement finishing watering etc. Complete

Item Description of Item Quantity Unit Rate In Amount

101 Providing and fixing MS Ladder of required 300.00 Kg 119.18

pattern with MS flats(30x3mm) or round or

square bars (12mm) at required spacing & with

round headed bolts and nuts or screws or

welding including primer coat of approved

quality and two coats of oil paintas as directed

by engineer in charge

102 Providing and fixing in position 150 mm high, 50.00 No 404.00

English letters made from 1.0 mm thick stainless

steel sheet as directed by Engineer in charge with

all necessary tools & plants etc. complete.

103 Providing and fixing polished 18 mm thick black 9.00 Sqmt 4107.67

granite with full round edge and double side

polished of approved quality in between urinal

and fixing with cement slurry & adhesive

including moulding of both exposed edges as

directed by engineering in charge etc. complete.

104 Constructing kitchen Platform of 18 mm thick 8.00 Sqmt 4192.51

Polished Black Granite at top and 25 mm thick

Kota stone slab one side polished at bottom with

cementing Materials / adhsives including

makeing necessary grooves in walls with

Vertical sandwich two Kotastone 25 mm support

every 60 cm centre to centre or as required

including all labour material of approved quality

incl. full moulded round front edge granite strip

of one side polished and jointed with grey

cement slurry including rubbing and polishing

etc. complete for all floors

105 Providing and fixing 25 mm thick polished kota 12.00 Sqmt 725.18

stone Shalve with full round edge and double

side polished of any required and fixing with

cement slurry & adhesive including both

exposed edges cut and Smooth Finished as

directed by engineering in charge etc. complete.

106 Providing & fixing in position glass partition 42.00 Sqmt 2739.12

with standard extruded colored anodized

aluminum frame size 63mm x 38mm x 2mm

thick make vertical and horizontal grid distance

as shown in drawing with 12mm thick toughen

glass directed with glass film, fixed with

transparent silicon rubber gasket in panel with

glazing clips 19 mm x 17.3mmx1.2mm in size

including fixtures and fastening with required all

labour and equipment and including rebar up to

slab level in half partition and as per detailed

drawing as directed with all lead and lift.

Item Description of Item Quantity Unit Rate In Amount

107 Providing and fixing Kitchen sink with C.I. or M.S. 2.00 No 3640.04

brackets, painted white including cutting holes in

walls and making good the same but excluding

fittings. (C) Vitreous China Sink.(i) 600mm x

450mm x 150mm size

108 Providing and fixing kitchen platform trolley 8.00 Sqmt 8049.70

having three drawers of SS (IS 304) of required

size like thali, katleri, perforated, partition,

cupsosar type in kitchen platform having drawer

front side and backside by using 19mm thick all

proof plywood of ISI quality all side laminated

etc. as directed. The size of SS (IS 304) basket of

size 4" to 18" for thali, dish, katleri, perforated,

partition, cupsosar type as directed including

necessary S.S. fittings, handles, nobs, telescopic

channels, etc. as directed

109 Providing and fixing 0.75 meter wide sand which 7.00 Sqmt 7291.19

type counter platform including supplying and

fixing granite stone of Z black or equivalant

quality 18 mm thick mirror polished on top and

side posiition and vertical strip at front with

cement slurry & adhesive including moulding of

both exposed edges over 25 mm thick kotah

stone platform fixing in top and sides and

itermediates supports fixing with cement mortar

and adhesive and finishing all material and

labour and assessories and 3 no flat back wash

with necessary fitting complete etc.

110 Providing and applying black japan treatment of 362.00 Sqmt 77.82

approved make and quality in two coats with

uniform finish and complete coverage, over

prepared surface free from dust, grease, or loose

particles. Surface shall be cleaned thoroughly

before application. The treatment shall be

applied with brushes only as per manufacturer's

specifications and allowed to dry between coats.

111 Providing & Fixing 114mm wide G.I. Sheets 372.00 Sqmt 4548.03

having weight not less than 490 Gm/m roll

formed to create 84mm wide louver snap fixed

on special shaped GI channel. Fix louvers &

channels shall finished with powder coating of

micron (1) 0.55mm thick sheet.etc. complet as

per detail drawing as directed.

112 Providing and laying and fixing 50 mm thick 83.00 Sqmt 1491.03

expansion joint by hydro cell semi rigid UV

resistance with high performance laminated

closed cell polythene foam joint filler in sheet

foam as directed, etc. complete.

Item Description of Item Quantity Unit Rate In Amount

113 Applying and providing Expansion joint sealing 57.50 Sqmt 4772.00

System on 100 mm vide joint including cleaning

of exansion joint by mechanical means provision

of adhesive and flexible membrane with required

bond length as per menufracturer specification

and 4mm thick alluminium strip covering with

one side sloted and bolted with suitable system,

inclusive of all manpower, machinery and

material as per specification and as directed.

114 Providing and filling the expansion joint by 57.50 Sqmt 515.39

Thioflex 600 polymer or equivalent confirm to BS

4254-1983 as per required shade and

manufactured specifi-cation by making groove of

50 mm x 12.5 mm lather by cutting or by

repairing groove and removing mortar drop or

any other foreign materials including applying

primer and filling required size (oversize of joint

PU foam etc. complete.

115 Providing and Fixing a set of wall mounted 38 2.00 NO 2671.45

mm dia U shaped horizontal stainless steel

collapsible grab bar , 38mm vertical stainless

steel fixed grab rail of grade SS 304 from round

pipe supported and 75 mm dia 8 mm thick SS

304 base flange on wall including anchor

fasteners, nuts, accessories as per detailed

drawing etc. complete as directed by Architect or

Engineer in charge.

116 Providing and fixing coloured self adhesive PU- 16.50 Sqmt 4586.41

Tactile tile, ground surface indicators of

Polyurethane) of size 300mm x 300mm for

guiding/warning to the visually visitors in the

centre/side of the pedestrian/approach pathway

as per specification and guidelines complete in all

respect to the entire satisfaction of in charge.

117 P& F BRAILE INDICATOR OF SIZE 170 MM X 25.00 Rmt 820.12

35MM FOR HANDRAILS OF THE APPROVED

DESIGN AND MAKE HAVE BRAILE DOTS RAISED

0.5 MM ABOVE BASE PLATE TO BE INSTALLED

AT SPECIFIC LOCATIONS AS PER DIRECTION OF

ENGINEER IN CHARGE

118 Providing and fixing of conspectus tape 50mm 6.00 Rmt 1247.35

width on of treads in staircase including cutting

pasting etc. As per harmonised guidelines

complete in all respect to the entire satisfaction

of engineer in charge.

Item Description of Item Quantity Unit Rate In Amount

119 Providing and Fixing 15 mm thick 300 mm x 300 30.00 Sqmt 1205.94

mm Tactile Warning Tiles (Attention Tiles i.e.

Tactile Warning Surface Indicator {TWSI}) of

Johnsan Endura Tac Button Yellow Plus or

equvqlent make in flooring laid on 20 mm thick

cement mortar 1:6 (1 cement : 6 coarse sand) on

new surface and jointed with cement slurry

including finished with flush pointing & cleaning

the surface for all floors as per detailed drawing

etc. complete as directed by Architect or

Engineer in charge. Thse tiles shall be Anti Skid,

Chemical Resistant, Fade Proof, Frost - Heat &

Weather Proof, High Flexural Strength, Highly

Durable, Stain Resistance . All Tactile Warning

Tiles meet the specific size and dimension

standards as required by ISO/FDIS

120 Providing and fixing 25 cm Wide & 3mm thick 46.00 Sqmt 1054.34

exterior composite panel on existing expansion

joint horizontally & vertically with all material,

hardware, acessories & fittings etc completed.

121 Extra for additional height of propping and 1663.00 Sqmt 407.75

centering where the height of propping and

centering exceeds 4 .O M between supporting

floor to ceiling including temporary brick or

stone pillars for supporting as required. (i)Height

more than 4.0 M.and upto 5.0 M.

122 Providing and laying cement concrete 1:2:4 (1- 339.00 Cumt 3741.68

Cement : 2- Coarse sand : 4- graded stone

aggregates 20 mm nominal size) and curing

complete excluding cost of formwork in (A)

Foundation and Plinth

123 Providing and laying controlled cement concrete 40.00 Cumt 10594.90

M-250 and curing etc. complete including the

cost of form work and excluding the cost of

reinforcement etc. complete in RCC Vertical and

horizontal wall for up to GL

124 Providing and fixing C.I. Manhole cover 0.60 M. x 2.00 Nos 958.17

0.45M. size having weight not less than 35Kg.

125 Providing & erecting open well horizontal mono 2.00 Nos 25856.00

block pump set with cast iron body, complete for

three phase submersible motor having

[H]For 3 H.P,3 phase open well horizontal mono

block pump set suitable for 1400 LPM to

LPM @ 33 to 42 MTR head suitable for 65/80

mm dia delivery pipe

Item Description of Item Quantity Unit Rate In Amount

126 Drilling of min. 250 mm dia. bore hole in all 100.00 Rmt 1138.27

strata including dualover burden strata by

combination DR/DTH rig including lowering

mm dia MS ERW pipes in bore hole and testing

etc.all work as per directed engineer incharge.

127 Manufacture, supply and delivery of cage 100.00 Rmt 1252.40

typeTrapezoidal shape ( ' V ') wire wound low

carbon, Galvanized screen pipe and Stainless

Steel Screen pipes, confirming IS: 8110 For (B)

200mm dia 1) 1.00mm Slot size

128 Bore plug having 100 mm height made from M.S. 1.00 No 1105.95

plate with 3 holes at equal distance on

circumference for nut-bolts type, locking

arrangement with nuts-bolts & lock nuts of std.

Make complete. For 250mm dia

129 Providing PVC insulated flat submersible cable as 120.00 Rmt 170.43

per detailed technical specifications of R/C of

GWSSB conforming to IS 694, IEC 60227 /

130 Suppling and installing 3 Phase Borewell 15.00 1.00 No 28879.94

HP Submersible Pump Sets Electric motor driven

conforming to I.S. 8034 and motor conforms to IS-

9283 working at 3 phase 400/440 volt 50 C/S

A.C. supply & 2900 R.P.M. cat

131 Providing and fixing check or non return pully 1.00 No 1111.00

wheel valve of 50 mm diameter.

132 Providing and fixing to wall,ceiliing and floor 90.00 Rmt 90.90

HDPE Pipes tubes ( Medium grade ) of the 50mm

nominal bore, tube, fittings and clamps included

making good the wall, ceilling and floor (F)

133 Providing and fixing to wall ceiling and floor 10.0 60.00 Rmt 339.05

Kg. F/Cm2 working pressure poluthene pipes of

the following outside Dia. Low densidy, complete

with special falnge compression type fittings,

wall clipsetc. including making good the wall

ceiling and floor.(G)110 mm

134 Providing and fixing to wall ceiling and floor 10.0 90.00 Rmt 696.90

Kg. F/Cm2 working pressure poluthene pipes of

the following outside Dia. Low densidy, complete

with special falnge compression type fittings,

wall clipsetc. including making good the wall

ceiling and floor.(G)160 mm

Item Description of Item Quantity Unit Rate In Amount

135 Providing junction for rain water juncton 6.00 Nos. 9262.71

chamber of size 0.60x0.60x0.75m with

excavation of size 1.96x1.96 m & 0.15m thick

c.c.1:2:4 bed concrete including brick masonary

wall in CM 1:6 of 0.75m height & 0.23m thick

with 15mm thick cement plaster inside & outside

& 1.06x1.06 RCC (1:2:4) slab of thickness 0.15m

with CRS steel and 0.60mx0.45m cast iron

manhole cover with frame weight not less than

35 kg as per directed by Engineer-in-charge

136 Providing Filter chamber of Brick work in C:M 6.00 Nos. 15601.47

1:6 of size 2.06mx1.20m x1.20m & excavation

dimension of 2.66mx 1.81x1.35m including C.C

1:2:4 bed concrete of 0.15m thick including brick

work in c.m 1:6 for 23cm thick wall including

15mm thick cement plaster inside & outside with

cement slurry & 10cm thick RCC 1:2:4 top cover

with frame of minimum weight of 35 kg & filling

filter material kapchi in layers (25-40mm & 10-

20mm) & BT metal 40mm & sand as per directed

by Engineer-in-charge.

137 Providing Recharging pit of size 2.0m Dia.& 2.0m 2.00 Nos. 8344.62

depth of water logging with excavation filling the

pit with gravel & sand in layers including making

300mm dia bore depth of 4.5mt & above

concrete with kapchi in layers (25-40mm & 10-

20mm) & BT metal 40mm & filling brick as

directed by Engineer-in-charge.

138 Constructing brick masonry chamber for 6.00 No. 7180.44

underground C.I. Inspection chamber and bends

with briocks having croshing strength not less

than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame

(Light duty) 455mm x 610mm intenal

dimensions, total weight of cover with frame to

be not less than 38Kg. (Wt. of cover 23 Kg.) and

Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4

mix (1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete

1:5:10 inside plaster 15mm thick with cement

mortar 1:3 finished smooth with a floating coat of

neat cement on walls and bed concrete etc.

complete.(iii) Inside dimensions 600mm x

mm and 450mm deep for pipe lines with three

or more inlets.

Item Description of Item Quantity Unit Rate In Amount

139 Providing and laying (two level or slopes) and 40.00 Rmt. 517.91

jointing with stiff mixture of Cement Mortar in

proportion 1:1, Salt glazed stone ware pipes of

pipes 150mm laying lime concrete 1:2:4 (1-Lime

putty :2-Fine samd : 4-Graded brick aggregates

40mm nominal size) bedding for stoneware

pipes of following internal diameters with

necessary formwork and curing complete.

140 Construction of granular sub-base 150 mm thick 261.10 Cum 1150.39

by providing coarse graded machine crushed B.T.

material satisfying MOST specification of grading

I (B.T. stone aggregate 53 mm to 26.5 mm 35 %,

26.5 to 4.75 mm - 45 % and 2.36 mm below -

% )including spreading in uniform layer with

motor grader on prepared surface, mixing by mix

in place method with rotavator at OMC and

compacting with vibratory roller to achieve the

desired density etc. complete.

141 Steel work, welded in built up sections framed 6638.00 kg 91.08

work including cutting, hoisting, fixing in position

and applying a priming coat of read lead paint &

two coat oil paint. (A)In beams and joists,

channels angles Tees, flats, with connecting

plates or angle cleats as in main and cross beams.

Hip and jack rafters, purlins conneted to common

rafters and the like..

142 Providing and fixing of Ridge flashing for roof 266.00 Sqmt 867.39

panel shall be made out of 0.5 mm thick pre

coated GI sheet . The Precoated sheet shall be of

minimum 240 mpa steel grade confirming to IS

14246:1995 and shall have zinc coating of

minimum 120 gsm as per IS:277:1992 , 5-7

microns epoxy primer on both side of the sheet

and polyester top coat 15-18 micron. The PPGI

Sheet shall have plastic protective guard film of

minimum 25 microns to avoid scratches during

transportation. The ridge shall be fixed to the

steel members by pop rivet or self drilling/self

stitching fastners @ maximum 450 mm c/c along

length of capping/flashing etc complete .

143 Providing and fixing pre-cast concrete kerb stone 594.00 Rmt 374.92

of gray cement based concrete block 30cm

ength,30cm height and 15cm thick of M250

grade concret as per approved design and

including excavation for fixing in proper line and

level,filling the joint with C:M 1:3 (1cement:3fine

sand) etc complete.

144 Box cutting the road surface to proper slope and 912.00 Cum. 109.41

camber for making a base for road work

including removing the excavated stuff and

depositing on the road side slope as directed

upto 50Mt.lead.

Item Description of Item Quantity Unit Rate In Amount

145 Providing and laying wet mix macadam base 208.00 Cum. 1306.94

course 250 mm thick in two layers using machine

crushed B.T. chips as per required gradation

mixing with required optimum quantity of water,

conveying the mix to site of work, spreading in to

grade and camber with mechanical paver and

consolidation each layer with vibratory roller

including cost of material labour plant and

equipment etc. complete.

146 Compaction and finishing of cement concrete 1383.00 Sqm 63.63

road by trimix process providing extra Labour

charges for the trimix vacume dewatering service

process on cement concrete road sutface by

using vacuum dewatering pump floater surface

vibrator including making groves and rough

finish to surface including leveling etc complete.

147 Providing and laying controlled cement concrete 272.60 Cumt 6095.35

M-250 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

148 Providing and filter media 600mm thick as 174.00 Sqmt 1311.18

directed at the back of Protection Wall as per

detailed specification.

149 Constructing providing and fabricating cattle 9.00 Sqmt 5168.17

guard using channel section frame of size ISMC

series 100 mm x 50 mm (Weight 9.20 kg/Rmt)

and ISMC section 100 mm x 75mm (weight

kg/Rmt) intermediate support for welding

G.I.pipe at 12 Cm C/C of size 50 mm in a frame

made of Channel section size 100 mm x 50 mm

all round including fixing the unit on prepared

chamber of masonary wall using MS hold fast

embeded in masonary wall top as directed by

Engineer in charge and as per drawing and

necessary required arrangement etc complete.

150 Providing and fixing decorative entrance gate 750.00 Kg 171.70

made out of cast iron and various mild steel

tabular section combination , the Ornamental

entrance gate should be fixed at compound wall

including pattern and die making , cutting

welding , grinding, fabrication , fixing in position

at compound wall with necessary pedestal,

bearing block and other locking arrangement.

The entrance gate should be painted with two

coats of priming coat of paint, and two coat of oil

paint etc complete. As per detail design and

instruction of architect.

Item Description of Item Quantity Unit Rate In Amount

151 Providing and fixing concertina coil fencing with 290.00 Rmt 834.26

punched tape concertina coil 600 mm dia 10 mt

openable length having 50 no rounds per 6 mt

length, upto 3mt height of wall with existing

angle iron (50mm x50mm x5mm )requird

shaped As per Directed Engeenier in charge.

placed 2.4mt or 3.00mt apart and with

horizontal R.B.T. reinforced barbed wire(3 mm)

stud tied with G.I. staples and G.I. clips to retain

horizontal, including necessary bolts or

G.I.barbed wire tied to angle iron, all complete as

per direction of Engineer-in-charge, with

reinforced barbed tape (R.B.T.)/Spring core (2.5

mm thick) and weight 43.478 gm/meter at

compound wall for ESR M4/ intakewell.

152 Earthwork for embankment including breaking 9308.97 Cum 169.28

clods, dressing with all lead and lift (excluding

watering and consolidation)(E) From Borrow

area within 3.0 Km. lead

153 Rolling of Earth work in layers with power roller 9308.97 Cum 23.12

and watering including filling in depressions

which occure during the process.

154 Supplying of well rotted FYM manure with all 28.00 Cum. 454.50

lead and Lift including spreading mixing dressing

and rolling with hand roller etc. complete.

155 Scarifying the surface of Soil including spreading 1092.00 Sqm 42.42

of DAP fertilizer mixing with Soil properly

levelling gand dressing of the plot

156 Supplying and planting Dibbing semi carpet lawn 1092.00 Sqm 106.05

at distance of abour 15 cm x 15 cm after proper

anti termite teratment amd rolling the seme by

hand roller amd wetering etc complete.

157 Bowing and developing flowering plants grown 50.00 No. 45.45

in nusery having approximate height 4 to 5 ft or

Height ad per Landscaps Plan with natural

growith of soil packed in polithyline bag or

Earthern pot. Including organic & chemical

fertilizer Pesticides, fungicides, hormones &

maintaining the plants up to three months as

deserted. Bottol palm.

158 Bowing and developing flowering plants grown 30.00 No. 60.60

in nusery having approximate height 4 to 5 ft or

Height ad per Landscaps Plan with natural

growith and nature colour planted in alump of

soil packed in polithyline bag or Earthern pot.

Including organic & chemical fertilizer pesticides,

fungicides hormones & maintaining the plants uo

to three months as deserted Trinagle Plan.

Item Description of Item Quantity Unit Rate In Amount

159 Bowing and developing flowering plants grown 30.00 No. 75.75

in nusery having approximate height 4 to 5 ft or

Height ad per Landscaps Plan with natural

growith and nature colour planted in alump of

soil packed in polithyline bag or Earthern pot.

Including organic & chemical fertilizer pesticides,

fungicides hormones & maintaining the plants uo

to three months as Jasud

160 Bowing and developing flowering plants grown 30.00 No. 106.05

in nusery having approximate height 4 to 5 ft or

Height ad per Landscaps Plan with natural

growith and nature colour planted in alump of

soil packed in polithyline bag or Earthern pot.

Including organic & chemical fertilizer pesticides,

fungicides hormones & maintaining the plants uo

to three months as Croton

161 Bowing and developing flowering plants grown 25.00 No. 25.25

in nusery having approximate height 4 to 5 ft or

Height ad per Landscaps Plan with natural

growith and nature colour planted in alump of

soil packed in polithyline bag or Earthern pot.

Including organic & chemical fertilizer pesticides,

fungicides hormones & maintaining the plants uo

to three months as deserted green mahindi

162 Bowing and developing flowering plants grown 25.00 No. 20.20

in nusery having approximate height 4 to 5 ft or

Height ad per Landscaps Plan with natural

growith and nature colour planted in alump of

soil packed in polithyline bag or Earthern pot.

Including organic & chemical fertilizer pesticides,

fungicides hormones & maintaining the plants uo

to three months as deserted New block ficus.

163 Labour charges for planting various plantsafter 190.00 No. 55.55

proper anti termite treatment in pits including

placing property and filling the pit with requred

prepared mix soil and wetering and dispporting

164 Maintance of the garder for 60 days after 1.00 Job. 50500.00

Complition of 3 month stipulated period is

completed for plantation o lawn and plants

including applying second round of proper

antitermite tretment.

165 Providnig and fixing to wall ceiling and floor 80 100.00 Rmt 447.72

Schedule Syntex / Astra (CPCV) or equivalent of

the following nominal bore tube fittings and

clamps the wall ceiling and floor (C) 40 mm

166 Providing and fixing consealed to wall, ceiling 140.00 Rmt 208.80

and floor 80 Schedule Syntex / Astral (CPVC) or

equivalent brand of the following nominal bore

tube fittings and clamps including Making goods

the wall ceilling and floor (A) 20 mm

Item Description of Item Quantity Unit Rate In Amount

167 Providing and fixing brass screw doen stop cock 2.00 Rmt 555.50

(A) 15 mm. Dia.

168 Rubber Hose pope 15 mm dia of approved brand 100.00 Rmt 60.60

169 Providnig and fixing G I Nipple as directed. 2.00 No. 50.50

170 Supply. installation, testing & commissioning of 1.00 No 325000.00

ISI approved Horizontal Split-Case type electrical

motor driven main fire pump set having

m3/hr. @ 70 m head. Kirloskar make, Horizontal

end suction, back pullout, top discharge

centrifugal pump with gland packed, with all

standard accessories base frame, coupling &

coupling guard and foundation bolts.The pump

unit shall be a horizontal direct mounted motor.

Motor speed shall be 3000 rpm. Unit shall

comprise the following minimum requirements:

a) Pump, b) Electric motor IE 2 type, c)

Foundation bolts, d) Air release valve, e) Mating

flanges with gasket and fasteners, f) Discharge

gauges, etc. complete in all respect. Model DB

80/26. R Motor 40H.P. / 2900 rpm. with labour,

171 Supply. installation, testing & commissioning of 1.00 No 525000.00

ISI approved Horizontal Split-case type diesel

engine driven stand-by fire pump set having

m3/hr. @ 70 m head. The pump unit shall be a

horizontallly mounted, coupled with diesel

engine. Unit shall comprise the following

minimum requirements:

a) Pump, b) Diesel Engine, c) Coupling, d) Air

release valve, i) Mating flanges with gasket and

fasteners, k) Discharge gauges, etc. complete in

Pump shall be coupled with suitable diesel

engine with heat exchanger cooled/water cooled

(radiator type) complete with base frame, anti-

vibration rubber pad, coupling with coupling

guard and foundation bolts, etc. engine shall have

have a speed of 1800-2000 rpm. Engine shall be

complete with flywheel, spider coupling, air

cleaners, corrosion resistor, oil sump with lube at

pump, governor, fuel filter, starting motor,

battery charging alternator & instrument panel

suitable for 24 volt DC including starting

switches, lead acid batteries of 24V & 180 amp-

harrating with termination, diesel engine

controller with supply cable from main panel to

DEC, suitable capacity of diesel oil tank (including

first fill) with all accessories, lube oil temperature

gauge, lube oil pressure, level gauge & high water

temperature, flexible exhaust connection &

Item Description of Item Quantity Unit Rate In Amount

172 Supply. installation, testing & commissioning of 1.00 No 94660.00

ISI approved Vertical In-line type electrical motor

driven jockey pump set having 10.8 m3/hr. @

70m head. The pump unit shall be a vertically

direct mounted motor. Unit shall comprise the

following minimum requirements:

a) Pump, b) Electric motor IE2, c) Foundation

bolts, d) Mating flanges with gasket and

fasteners, e) Discharge gauges, etc. complete in

all respect, with labour, with GST.

173 Suppy, Installing, Testing and Commissioning of 2.00 No 13936.00

Normax make C.I. Heavy duty foot valve with

flangs, Nut bolts, Gaskets etc. with necessary

complete accessories. 150 mm

174 Suppy, Installing, Testing and Commissioning of 1.00 No 4500.00

Normax make C.I. Heavy duty foot valve with

flangs, Nut bolts, Gaskets etc. with necessary

complete accessories. 80 mm

175 Supply, installation, testing & commissioning of 1.00 No 235000.00

common control panel suitable for for main

electrical motor driven fire pump (1no.), Auto

start of diesel engine driven standby fire pump, &

jockey electrical motor (1 no.) Auto start of Main

and jockey pump, fire red powder coated Motor

Control Center with Aluminium busbar and

weather proof enclosure (IP 54) motor control

center (MCC). MCC enclosure shall be facbricated

from CRCA sheet, door & partition shall be

SWG complete with incomer, Star Delta/DOL

starter bus bar, protective fuses, indicating lamps

with interlock facility with bottom/top entry

with foot mounting (on channel frame) type

complete with all accessories.(all componenets of

L&T & Schneider/siemens make). With

battery charger tricle/booster arrangement for

diesel battery charging.

FRLS Power & control cable for main electric

pump including earthing from motor control

centre (MCC panel) to pump & all instruments

(pressure switchs) with all complete. Power

cabling & control cabling including earthing from

MCC panel to all pumps & all instruments

(pressure switches) inside pump house.

176 Providing and erecting XLPE (IS:7098)(I)88 ISI 50.00 No 336.00

marked armoured cable multistrand Aluminium

conductor for 1.1 KV to be laid with necessary

clamps or in existing cable trench / trays from

Fire panel to the motors.

Item Description of Item Quantity Unit Rate In Amount

177 Supply, installation, testing & commissioning of 1.00 No 55000.00

Priming tank,HDPE type, min. 1000 litres,

necessary piping for priming the pumps of

mm size, butterfly valves for isolation, NRV

mm to prevent back flow, Water Filling piping

min. 50 mm size, to priming tank ,with all

178 Supply, installation, testing & commissioning of 1.00 Set 70000.00

Manifold( surge vessel,)for fire hydrant system,

min. 300 mm diameter, made from M.S plate,

hydro tested to 15 kg./cm2. with ball valves,

header with couplings for fitting pressure

switches, pressure gauges etc.with necessary

isolation valves with all complete.

179 Supply, installation, testing & commissioning of 1.00 Job 20000.00

instrumentation for automatic operation of all

pump sets including 3 nos. pressure switches and

4 nos. 150 mm dia. dial Burdon Type Glycerine

Filled pressure gauges with SS syphon & isolation

ball valve arrangements with necessary isolation

valves with all complete.

180 Supply, fabrication & erection of aboveground 30.00 Mtr 3258.00

G.I. ERW piping, conforming to IS:1239, part-I,

Heavy C class up to 150 mm dia. and IS:3589, for

size 200 mm dia. & above, thickness. G.I. pipe

fitting's as per IS: 1239, part-II, Heavy C class for

size 150 mm dia. & below & IS: 3589, min.

mm, for size 200 mm dia. above, flanges, nuts

bolts & washers, 3 mm thick gasket, pipe

Hydrostatic testing for 2 hour's at 150% of the

system pressure, hook-up etc.

Painting for piping, fittings & structural pipe

support, shall be two coat of zinc primer and two

coats of fire red conf. to IS: 5, Shade

Complete with all accessories as per approved

drawings, specicification and direction of the

Engineer-in-Charge, with all complete. 200 mm

Item Description of Item Quantity Unit Rate In Amount

181 Supply, fabrication & erection of aboveground 30.00 Mtr 2431.00

G.I. ERW piping, conforming to IS:1239, part-I,

Heavy C class up to 150 mm dia. and IS:3589, for

size 200 mm dia. & above, thickness. G.I. pipe

fitting's as per IS: 1239, part-II, Heavy C class for

size 150 mm dia. & below & IS: 3589, min.

mm, for size 200 mm dia. above, flanges, nuts

bolts & washers, 3 mm thick gasket, pipe

Hydrostatic testing for 2 hour's at 150% of the

system pressure, hook-up etc.

Painting for piping, fittings & structural pipe

support, shall be two coat of zinc primer and two

coats of fire red conf. to IS: 5, Shade

Complete with all accessories as per approved

drawings, specicification and direction of the

Engineer-in-Charge, with all complete 150 mm

182 Supply, fabrication & erection of aboveground 45.00 Mtr 1567.00

G.I. ERW piping, conforming to IS:1239, part-I,

Heavy C class up to 150 mm dia. and IS:3589, for

size 200 mm dia. & above, thickness. G.I. pipe

fitting's as per IS: 1239, part-II, Heavy C class for

size 150 mm dia. & below & IS: 3589, min.

mm, for size 200 mm dia. above, flanges, nuts

bolts & washers, 3 mm thick gasket, pipe

Hydrostatic testing for 2 hour's at 150% of the

system pressure, hook-up etc.

Painting for piping, fittings & structural pipe

support, shall be two coat of zinc primer and two

coats of fire red conf. to IS: 5, Shade

Complete with all accessories as per approved

drawings, specicification and direction of the

Engineer-in-Charge, with all complete 100 mm

183 Supply, fabrication & erection of aboveground 50.00 Mtr 1131.00

G.I. ERW piping, conforming to IS:1239, part-I,

Heavy C class up to 150 mm dia. and IS:3589, for

size 200 mm dia. & above, thickness. G.I. pipe

fitting's as per IS: 1239, part-II, Heavy C class for

size 150 mm dia. & below & IS: 3589, min.

mm, for size 200 mm dia. above, flanges, nuts

bolts & washers, 3 mm thick gasket, pipe

Hydrostatic testing for 2 hour's at 150% of the

system pressure, hook-up etc.

Painting for piping, fittings & structural pipe

support, shall be two coat of zinc primer and two

coats of fire red conf. to IS: 5, Shade

Complete with all accessories as per approved

drawings, specicification and direction of the

Engineer-in-Charge, with all complete 80 mm

Item Description of Item Quantity Unit Rate In Amount

184 Supply, fabrication & erection of aboveground 25.00 Mtr 575.00

G.I. ERW piping, conforming to IS:1239, part-I,

Heavy C class up to 150 mm dia. and IS:3589, for

size 200 mm dia. & above, thickness. G.I. pipe

fitting's as per IS: 1239, part-II, Heavy C class for

size 150 mm dia. & below & IS: 3589, min.

mm, for size 200 mm dia. above, flanges, nuts

bolts & washers, 3 mm thick gasket, pipe

Hydrostatic testing for 2 hour's at 150% of the

system pressure, hook-up etc.

Painting for piping, fittings & structural pipe

support, shall be two coat of zinc primer and two

coats of fire red conf. to IS: 5, Shade

Complete with all accessories as per approved

drawings, specicification and direction of the

Engineer-in-Charge, with all complete 50 mm

185 Supply, fabrication & erection of aboveground 100.00 Mtr 365.00

G.I. ERW piping, conforming to IS:1239, part-I,

Heavy C class up to 150 mm dia. and IS:3589, for

size 200 mm dia. & above, thickness. G.I. pipe

fitting's as per IS: 1239, part-II, Heavy C class for

size 150 mm dia. & below & IS: 3589, min.

mm, for size 200 mm dia. above, flanges, nuts

bolts & washers, 3 mm thick gasket, pipe

Hydrostatic testing for 2 hour's at 150% of the

system pressure, hook-up etc.

Painting for piping, fittings & structural pipe

support, shall be two coat of zinc primer and two

coats of fire red conf. to IS: 5, Shade

Complete with all accessories as per approved

drawings, specicification and direction of the

Engineer-in-Charge, with all complete 25 mm

Item Description of Item Quantity Unit Rate In Amount

186 Supply, installtion, testing & commissioing of 20.00 Mtr 3065.00

Underground GI (ERW) piping conforming to

IS:1239, part-I, Medium class ('B' class) up to

mm dia. and IS:3589 heavy class ('C' class), for

200 mm dia. & above, min. 6.35mm thickness

including Medium class fittings, anti-corrosive

tape of size 150 mm wide x 4 mm thick,

wrapping & coating with 13KV holiday testing .

Rates shall include sand bedding of 75mm dia all

around, backfilling of the excavated including

installation of heavy pipe fitting's, flanges, etc.

10 % of all the welded joints shall be done

radiographically tested and 50% of the joints

radiographed shall be the "Field Joints".

Hydrostatic testing for 2 hours at 150% of the

system pressure, hook-up etc., complete with all

accessories as per approved drawings,

specicification and direction of the Engineer-in-

Charge, with all complete. (Road Crossing)

187 Supply, installtion, testing & commissioing of 10.00 Mtr 1995.00

Underground GI (ERW) piping conforming to

IS:1239, part-I, Medium class ('B' class) up to

mm dia. and IS:3589 heavy class ('C' class), for

200 mm dia. & above, min. 6.35mm thickness

including Medium class fittings, anti-corrosive

tape of size 150 mm wide x 4 mm thick,

wrapping & coating with 13KV holiday testing .

Rates shall include sand bedding of 75mm dia all

around, backfilling of the excavated including

installation of heavy pipe fitting's, flanges, etc.

10 % of all the welded joints shall be done

radiographically tested and 50% of the joints

radiographed shall be the "Field Joints".

Hydrostatic testing for 2 hours at 150% of the

system pressure, hook-up etc., complete with all

accessories as per approved drawings,

specicification and direction of the Engineer-in-

Charge, with all complete. (Road Crossing)

188 Supply, installation, testing & commissioning of 2.00 No 18750.00

Cast iron body double flanged gate valve conf. to

IS: 14846, PN-1.6 with mating flanges, drilling as

per IS/ANSI 150# with mating flanges,

galvanized nut, bolts & washers, gasket 3 mm

thick, etc., with all complete. 150 mm dia.

Item Description of Item Quantity Unit Rate In Amount

189 Supply, installation, testing & commissioning of 2.00 No 10750.00

Cast iron body double flanged gate valve conf. to

IS: 14846, PN-1.6 with mating flanges, drilling as

per IS/ANSI 150# with mating flanges,

galvanized nut, bolts & washers, gasket 3 mm

thick, etc., with all complete. 100 mm dia.

190 Supply, installation, testing & commissioning of 1.00 No 7000.00

Cast iron body double flanged gate valve conf. to

IS: 14846, PN-1.6 with mating flanges, drilling as

per IS/ANSI 150# with mating flanges,

galvanized nut, bolts & washers, gasket 3 mm

thick, etc., with all complete. 50 mm dia.

191 Supply, Installation, Testing & Commissioning of 2.00 No 6750.00

Cast iron body Butterfly valve according to IS:

13095, PN-1.6, ISI mark, below Lever operated

and above 150 mm dia. Gear operated complete

with mating flanges /ANSI class # 150 with bolts

& nuts washers, rubber gaskets 3 mm thick, etc.,

with all complete. 150 mm dia.

192 Supply, Installation, Testing & Commissioning of 2.00 No 5500.00

Cast iron body Butterfly valve according to IS:

13095, PN-1.6, ISI mark, below Lever operated

and above 150 mm dia. Gear operated complete

with mating flanges /ANSI class # 150 with bolts

& nuts washers, rubber gaskets 3 mm thick, etc.,

with all complete. 100 mm dia.

193 Supply, Installation, Testing & Commissioning of 1.00 No 4550.00

Cast iron body Butterfly valve according to IS:

13095, PN-1.6, ISI mark, below Lever operated

and above 150 mm dia. Gear operated complete

with mating flanges /ANSI class # 150 with bolts

& nuts washers, rubber gaskets 3 mm thick, etc.,

with all complete. 50 mm dia.

194 Supply, installation, testing & commissioning of 2.00 No 5517.00

Cast iron body NRV conf. to IS: 5312, PN-1.6, Dual

Plate type with S.S flap, IS mark, complete with

mating Flanges/IS/ ANSI class # 150 with bolts &

nuts, washers, gaskets 3 mm thick, etc., with all

complete. 150 mm dia.

195 Supply, installation, testing & commissioning of 2.00 No 3700.00

Cast iron body NRV conf. to IS: 5312, PN-1.6, Dual

Plate type with S.S flap, IS mark, complete with

mating Flanges/IS/ ANSI class # 150 with bolts &

nuts, washers, gaskets 3 mm thick, etc., with all

complete. 100 mm dia.

Item Description of Item Quantity Unit Rate In Amount

196 Supply, installation, testing & commissioning of 1.00 No 2500.00

Cast iron body NRV conf. to IS: 5312, PN-1.6, Dual

Plate type with S.S flap, IS mark, complete with

mating Flanges/IS/ ANSI class # 150 with bolts &

nuts, washers, gaskets 3 mm thick, etc., with all

complete. 50 mm dia.

197 Supply, installation, testing & commissioning of 1.00 No 8000.00

Four way fire brigade Inlet connection with

mm dia. stainless steel (SS304) instantaneous

male inlets with built in non return valve in each

inlet with 150 mm dia. header pipe, suitable

rubber cap and GI chain including nuts, bolts,

washers, gasket 3 mm thick, etc. with all

complete.As per IS 903. ISI mark.

198 Supply, installation, testing & commissioning of 12.00 No 4345.00

Oblique pattern type stainless steel (SS 304)

single headed External Fire Hydrant Valve , ISI,

with 63 mm dia. female instantaneous outlet

conf. to IS: 5290, type - A, including mating

flanges, galvanised nuts, galvanised bolts/studs,

washers & gaskets 3 mm thick with all complete.

199 Supply, installation, testing & commissioning of 12.00 No 1409.00

63 mm dia., ISI , stainless steel (SS 304) Universal

Branch Pipe conf. to IS:

200 Supply & installation, testing & commissioing of 12.00 No 4759.00

Fire Fighting Hose - conf. to IS : 636, type - A, ISI,

The fire hose shall be 15 m long with 63 mm dia.

stainless steel (SS 304) couplings conf. to IS:

at both the ends for connection with the hydrant

valve and the branch pipe.

201 Supply, installation, testing & commissioning of 12.00 No 2809.00

fabricated from 3 mm CRC sheet, hose boxe of

size-750 mm x 600 mm x 250 mm - painted with

Fire Redas per IS: 5, shade no. 536 color from

outside & white enamel from inside , front 3 mm

thick transparent glass with key, handle and

brass hinges - to accommodate 2 nos. of 15 mtr

long hose and 1 no. universal branch pipe,

including supporting arrangement with civil

202 Supply, Installation, testing & commissioing of 12.00 No 5809.00

Swinging type mild steel hose reel drum with

mm dia. x 30 mtr. rubber hose as per IS:

The mounting stand shall be of mild steel and the

hose shall be fitted with a SS shut-off nozzle & SS

ball valve of 25 mm dia. including supporting

arrangement with all complete.

203 Supply & Installation, Testing & Commissioing of 4.00 No 1100.00

25 mm dia gun metal Air Release valve with

mm dia. stainless steel ball valve.

Item Description of Item Quantity Unit Rate In Amount

204 Supply, Installation, Testing & Commissioning of 1.00 No 27500.00

Fixed Stand Post Type Water Monitor as per IS:

8442 , monitor having 100 mm inlet connection

with flow of 1750 lpm with all complete and

mm dia. gate valve, IS: 13095, PN-1.6, with

mating flanges drilling as per IS: 6392/IS:

1538/B 16.5/ASA 150#, galvanised nuts,

bolts/studs & washers, neoprene rubber gasket

3mm thick., etc. with all complete.

205 Provide complete demonstration of whole fire 1.00 Job 85000.00

system for three years and obtaining fire NOC

from SMC/ Nagar palika for three years as per

Govt. rules & Regulations. Fees for SMC/ Nagar

palika for Fire NOC will be paid by department

and other services included in this items except

Annual maintenance contract.

206 Design , Supply and installation of Safety signage 10.00 Sq.m 4842.00

made of Zinc Sulphilde based glow in dark , Rigid

sheet with High Luminous property enclosed in a

transperent weather proof UV stabilized plastic

pasted on 3 mm thick clear acrylic sheet such as

EXITS, EMERGENCY EXIT, DO NOT USE LIFT

DURING FIRE, FLOOR MARKINGS, FIRE LIFT,

STAIRCASE EXIT, FIRE ALARM CALL POINT, FIRE

HOSE REEL, FIRE HYDRANT POINT etc.

207 Supply, installation, testing & commissioning of 2.00 No 35000.00

Basket Type Strainer complete with mating

Flanges/IS/ ANSI class # 150 with bolts & nuts,

washers, gaskets 3 mm thick, etc., with all

complete. 150 mm dia.

208 Supply, installation, testing & commissioning of 1.00 No 13475.00

Basket Type Strainer complete with mating

Flanges/IS/ ANSI class # 150 with bolts & nuts,

washers, gaskets 3 mm thick, etc., with all

complete. 80 mm dia.

209 Supply, Installtion, Testing & Commissioing of 30.00 No 600.00

Standard Response Sprinkler, Pendent Brass

Sprinkler, Quartzoid Bulb type with crome finish,

nickel crome platde, K factor K-80, Temp.- 680C,

1/2" end connection including resessed

escutcheon. (UL Listed).

210 Supplying of 25 mm dia UL Listed SS braided 30.00 No 750.00

Sprinkler Flexible Hose of having 15mm end

connection outlet with supporting arrangement

from false ceiling frame and having max. test

pressure of 60 bar and max. working pressure of

12 bar at 149 deg.c. maximum temperature. (UL

Item Description of Item Quantity Unit Rate In Amount

211 Supply, Installation, Testing & Commissioing of 1.00 No 48000.00

UL Listed Ductile Iron Wet Alarm Control valve,

internally and externally painted, pre-trimmed

with bi-pass connection, test and drain

connection, tested to 1.5 times the working

pressure, with pressure gauge, water motor

gong, including matching flanges, galvanised

bolts/studs, nuts, washers & gaskets, with all

complete. 100 mm dia.

212 Supply, Installation, Testing & Commissioning of 1.00 No 5500.00

UL Listed Water Flow Switch, with NO & NC

Contacts with all complete. 100 mm dia.

213 Supply, Installation, Testing, & Commissioning of 8.00 No 1950.00

Stainless Steel Ball Valve for drain, with all

complete. 50 mm dia

214 Supply, Installation and commissioning of ABC 20.00 No 2140.00

type fire extinguisher, capacity 5 kg. as per IS

14609 / 15683. With necessary fittings.

215 Supply, Installation and commissioning of CO2 20.00 No 6150.00

type fire extinguisher, capacity 4.5 kg. as per IS

15222/15683. With necessary fittings.

216 Supply, Installation, and commissioning of Fire 1.00 No 225000.00

Alarm panel , Addressible type, 8 loops, with

complete accessories, Make Honeywell.

217 Supply, Installation, and commissioning of optical 12.00 No 2300.00

smoke detectors with complete accessories,

Make Honeywell.

218 Supply, Installation, and commissioning of 12.00 No 5025.00

Intelligent Wall Mounted Sounder, Red with Pure

White skirt with complete accessories, Make

219 Supply, Installation, and commissioning of Red 12.00 No 4030.00

Add Call Point, Flush Mounting, Glass with base

with complete accessories, Make Honeywell.

220 Armour Cable for Fire Alarm system, two core, 500.00 Mtr 120.00

1.5 mm2, FRLS type,

221 Supplying FIRE bucket round bottom of 9 litres 8.00 No 1480.00

capacity made out of 24 gauge G.I Sheet with

extra handle at bottom duly painted white inside

and Red out side with FIRE mark. Filled with dry-

sand and kept on existing stand provided or hung

222 Supplying and erecting floor mounting Stand for 2.00 No 4000.00

keeping four nos. of FIRE buckets comprising

1500 mm in length, 900 mm height frame made

out of 30mm x 30 mm x 4 mm angle iron with

cross suports legs, welded with 4 hooks and duly

painted with one coat of red lead and two coats

of approved enamelled silver paint.

Item Description of Item Quantity Unit Rate In Amount

223 Point wiring for Light / Bell with 2-1.5 sq.mm 484.00 Pt. 485.81

& earth wire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length , in

below type of pipe erected with 6A Modular type

switch / bell push & accessories and earth

continuity of following type, erected on PVC /

Metallic/Wooden box, single mounting base

frame covered with textured/ metallic/ white

front plate modules erected on / in wall / ceiling

as per pipe erected, with necessary Lamp holder/

ceiling rose / H.D.Connector as directed. (f) with

medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat.

III (Wire :- KEI/ RR Kabel/Havells/Apar Pipe :-

Vraj/Nihir/Anchor/Precision/Polycab Accesories

Roma/Havells/Honeywell/L&T/Greatwhite)

224 Point wiring for FAN with 2-1.5 sq.mm & earth 239.00 Pt. 674.68

wire of 1.5 sq.mm (Green) both are of .ISI marked

1.1 KV Grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in below type

of pipe erected with 6A Modular type switch

and hum free EME step type electronic fan

regulator mounted and accessories with earth

continuity of following type erected on PVC /

Metallic/ Wooden box, single mounting base

frame covered with textured/metallic/white

front plate modules erected on / in wall / ceiling

as per pipe erected. with necessary ceiling rose /

H.D.Connector as directed. (f) with medium class

Rigid PVC pipe and accessories erected concealed

in wall/ceiling complete Cat. III (Wire :- KEI/ RR

Kabel/Havells/Apar Pipe :-

Vraj/Nihir/Anchor/Precision/Polycab Accesories

Roma/Havells/Honeywell/L&T/Greatwhite)

225 Point wiring for on board Looped Plug with 6A 119.00 Pt. 257.55

Modular type switch & 5 pin socket erected on

PVC/ Metallic/ Wooden box, single mounting

base frame covered with textured / metallic/

white front plate modules erected on/ in wall/

ceiling with following type accessories Cat. III

Accesories :- Anchor

Roma/Havells/Honeywell/L&T/Greatwhite)

Item Description of Item Quantity Unit Rate In Amount

226 Providing following type of Modular Type 78.00 Nos 151.50

Accessories mounted with PVC /

metallic/Wooden box, single mounting base

frame covered with textured / metallic/white

front plate , modules erected with necessary

connections as per site situation directed by

Engineer In charge. (1)One No. SP 6 Amp. Cat.III

(Accesories :- Anchor

Roma/Havells/Honeywell/L&T/Greatwhite)

227 (2) One No 5 pin plug Cat.III (Accesories :- 78.00 Nos 151.50

Roma/Havells/Honeywell/L&T/Greatwhite)

228 (3) Two Pin/RJ-11 Telephone Socket [A] For One 13.00 Nos 160.59

Gang Cat.III (Accesories :- Anchor

Roma/Havells/Honeywell/L&T/Greatwhite)

229 (8) Computer RJ-45 socket Cat.III (Accesories :- 93.00 Nos 160.59

Roma/Havells/Honeywell/L&T/Greatwhite)

230 (9) 16 Amp. SP one way switch Cat.III 90.00 Nos 180.79

(Accesories :- Anchor

Roma/Havells/Honeywell/L&T/Greatwhite)

231 (10) 6/16Amp. Universal socket Cat.III 90.00 Nos 199.98

(Accesories :- Anchor

Roma/Havells/Honeywell/L&T/Greatwhite)

232 Providing and erecting ISI mark Medium class 2800.00 Mtr. 24.24

RIGID PVC PIPES of following size complete to be

erected on/in wall or ceiling erected with

necessary PVC fittings & Junction boxes fixed

with adhesive solution & Clamps with following

dia of pipes, in approved manner as directed (a)

20 mm (Wire :- KEI/ RR Kabel/Havells/Apar

Pipe :- Vraj/Nihir/Anchor/Precision/Polycab

233 Providing and erecting Mains with 1.1 KV grade 3546.00 Mtr. 82.82

FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be

erected concealed in /flushed on wall/ceiling,

with 1.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size (A) With medium

class Rigid PVC pipe and accessories (b) 2 wire

2.5 sq. mm (Wire :- KEI/ RR Kabel/Havells/Apar

Pipe :- Vraj/Nihir/Anchor/Precision/Polycab

Item Description of Item Quantity Unit Rate In Amount

234 Providing and erecting Mains with 1.1 KV grade 4095.00 Mtr. 112.11

FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm

copper conductor FRLS PVC insulated stranded

wire of green colour for earth continuity of

following size (A) with medium class Rigid PVC

pipe and accessories (a) 2 wire 4 sq. mm (Wire :-

KEI/ RR Kabel/Havells/Apar)

235 (g) 4 wire 4 sq. mm (Wire :- KEI/ RR 1350.00 Mtr. 180.79

Kabel/Havells/Apar)

236 (h) 4 wire 6 sq. mm (Wire :- KEI/ RR 360.00 Mtr. 260.58

Kabel/Havells/Apar)

237 Providing and erecting Mains with ISI marked, 366.00 Mtr. 56.56

1.5KV grade electrolyte multi stranded, annealed

copper conductor with heat resistant PVC

insulated conforms to IS 694, IEC - 227 erected in

existing pipe of following size (Specifically for

control panel, relays, power switchgears, motor

starters & control wiring) with required size of

copper lugs, nuts and bolts if required. (e) One

wire 6.00 sq. mm (Wire :- KEI/ RR

Kabel/Havells/Apar)

238 (f) One wire 10.00 sq. mm (Wire :- KEI/ RR 417.00 Mtr. 91.91

Kabel/Havells/Apar)

239 (g) One wire 16.00 sq. mm (Wire :- KEI/ RR 69.00 Mtr. 142.41

Kabel/Havells/Apar)

240 (h) One wire 25.00 sq. mm (Wire :- KEI/ RR 6.00 Mtr. 236.34

Kabel/Havells/Apar)

241 (i) One wire 35.00 sq. mm (Wire :- KEI/ RR 6.00 Mtr. 300.98

Kabel/Havells/Apar)

242 (j) One wire 50.00 sq. mm (Wire :- KEI/ RR 6.00 Mtr. 470.66

Kabel/Havells/Apar)

243 Supplying and erecting Flexible PVC insulated 88.00 Mtr. 46.46

multi strand multi core 1.1 kv grade ISI marked

copper wires of following size to be erected as

directed. (e) 1.50 Sq.mm 3 core round PVC

244 (h) 2.50 Sq.mm 3 core round PVC sheathed 150.00 Mtr. 77.77

245 Supplying & erecting approved make Telephone 325.00 Mtr. 20.20

Cable electrolytic copper conductor PE insulation

twisted in two pairs, & wrapped with FRLS PVC

tape & sheathed with FRLS PVC or HFFR outer

Jacket suitable for telephone wiring & confirming

to C-DOT erected in existing pipe. of following

size of conductors & nos.of pairs. With necessary

connections. [A] Conductor Size 0.5 mm (a)

Unarmoured (2) Two Pairs

246 Supplying & erecting approved make LAN cable 2325.00 Mtr. 47.47

of following size in existing pipe as per direction

Item Description of Item Quantity Unit Rate In Amount

247 Providing & erecting Switch board for Computer 93.00 Nos. 1133.22

or electric apparatus consisting of following

modular type accessories mounted with PVC/

Metallic concealed/ open box with single

mounting base frame covered with textured/

metallic/ white front plate,modules erected with

necessary connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug

For Modular Type Accessories

Cat. III (Accesories :- Anchor

Roma/Havells/Honeywell/L&T/Greatwhite)

248 Decorative call bell Ting-tong box type 250 volts 1.00 Nos. 71.71

complete erected

249 Supplying and erecting LED indoor fittings with 383.00 Nos. 373.70

LEDs of wattage 0.2 Watt to 0.5 Watt assembled

on single MCPCB, with housing used as a heat

sink shall be made of thick sheet Steel

conforming to IS: 513/ CRCA/ aluminium die cast

powder coated and high U.V. & corrosion

resistance with diffuser with company

mark/name 160V to 270V, Power Factor more

than 0.95, THD < 15%, CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/ watt, LED driver

efficiency > 85 % (fitting required LM-79 & LM-

80 Certificates) (NOTE: Below description have

shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.) (A)

Tube Light with integral driver (iv) 22-24 Watts,

Surge - 2KV,IP-20, conventional 4 feet Cat.III

(Make :-Philips/

Havells/Wipro/Jaquar/Pyrotech)

250 Supplying and erecting led lamps with following 19.00 Nos. 112.11

wattage capacity of 220 to 240 voltage, minimum

15000 burning hours life, 500 V in built-surge

protection,Polycarbonate diffuser, mounting

suitable for E14 / E27 / B22 lamp holders, pf >=

0.5 (A) LED Lamps integral type, with PC diffuser

suitable LAMP holder (ii) 5 to 8 watts Cat-III

(Make :-Philips/

Havells/Wipro/Jaquar/Pyrotech)

Item Description of Item Quantity Unit Rate In Amount

251 Supplying and erecting LED indoor fittings with 6.00 Nos. 589.84

LEDs of wattage 0.2 Watt to 0.5 Watt assembled

on single MCPCB, with housing used as a heat

sink shall be made of thick sheet Steel

conforming to IS: 513/ CRCA/ aluminium

pressure die cast powder coated and high U.V. &

corrosion resistance with diffuser housed in

aluminium casted body with company mark/

name 160V to 270V, Power Factor more than

Luminaire efficacy> 85 lumens/watt, LED driver

efficiency > 85 % (fitting required LM-79 & LM-

80 Certificates) (NOTE: Below description have

shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.) (A)

Square/ Circular shaped Surface/Recessed

Mount Downlight with provision for spring

loaded mounting clips complete.IP20 (iii) 16-20

watts, Surge-2 KV Cat.III (Make :-Philips/

Havells/Wipro/Jaquar/Pyrotech)

252 (B) LED Panel Light with provision for Plane 30.00 Nos. 1794.77

front frame with translucent cover fixed to

housing complete.IP20 (vi) 36 watts, 24" x 24",

Surge- 2KV Cat.III (Make :-Philips/

Havells/Wipro/Jaquar/Pyrotech)

253 Supplying and erecting LED street light / Flood 22.00 Nos. 4997.48

light fittings with High power White LEDs

wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and

corrosion free High pressure die cast aluminum

housing with smooth finish powder coated and

heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened

glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than

5700K,Uniformity ratio >0.45, Luminaire

efficacy> 100 lumens/watt . LED driver efficiency

> 85 %. (fittings required LM-79 & LM-80

certificates) (NOTE: Below description have

shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.) (A)

Street Light (IP-65), Surge protection -4KV

integral and ,Light must have 440VAC line supply

with over-voltage protection. (ii) above 48 to

Watts Cat.III (Make :-Philips/

Havells/Wipro/Jaquar/Pyrotech)

Item Description of Item Quantity Unit Rate In Amount

254 (B) Flood Light (IP-65), Surge protection -4KV 2.00 Nos. 7266.95

integral and ,Light must have 440VAC line supply

with over-voltage protection. (iv) above 90 to

120 watts Cat.III (Make :-Philips/

Havells/Wipro/Jaquar/Pyrotech)

255 (C) Post Top Lantern LED fitting comprises of 2.00 Nos. 4819.72

finish cast aluminum spigot and spun aluminum

canopy fixed with opal polycarbonate, pipe

arrangement for vertical mounting driver and

accessories wired upto terminal block.IP

(ii)32-40W Cat.III (Make :-Philips/

Havells/Wipro/Jaquar/Pyrotech)

256 Providing and erecting Approved make Four pole 16.00 Nos. 6173.12

moulded case circuit breaker having breaking

capacity ICU of 25 KA. at 415 V,having normal

current rating up to 25 A to 100A. with Fixed

thermal & magnetic release suitable to work on

A.C. supply 50 c/s. with all internal connections,

spreader tinned copper & complete erected in

existing 16 G.M.S. housing. ICS=100% of ICU only

Cat III (Make :-

L&T/Siemens/ABB/C&S/Havells/)

257 Providing and erecting Approved make Four pole 23.00 Nos. 16221.61

moulded case circuit breaker having breaking

capacity ICU of 35 KA. at 415 V. having Normal

current rating 200A.with variable Thermal &

magnetic release suitable to work on A.C.supply

50 c/s. with all internal connections, spreader

tinned copper & complete erected in existing

G.M.S.housing ICS=100% of ICU only Cat

III (Make :-L&T/Siemens/ABB/C&S/Havells)

258 Providing and erecting Approved make Four pole 2.00 Nos. 16221.61

moulded case circuit breaker having breaking

capacity ICU of 35 KA. at 415 V. having Normal

current rating 200A.with variable Thermal &

magnetic release suitable to work on A.C.supply

50 c/s. with all internal connections, spreader

tinned copper & complete erected in existing

G.M.S.housing ICS=100% of ICU only Cat III

(Make :-L&T/Siemens/ABB/C&S/Havells)

259 Providing and erecting Approved make Four pole 2.00 Nos. 20946.39

moulded case circuit breaker having breaking

capacity ICU of 35 KA. and above at 415 V .

having normal current rating 250A. with

variable thermal & magnetic release suitable to

work on A.C.supply 50 c/s. with all internal

connections, spreader tinned copper & complete

erected in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III (Make :-

L&T/Siemens/ABB/C&S/Havells)

Item Description of Item Quantity Unit Rate In Amount

260 Providing and erecting Approved make Four pole 2.00 Nos. 25228.79

moulded case circuit breaker having breaking

capacity ICU of 50 KA and above at 415 V having

Normal current rating 400A. with variable

Thermal & magnetic release suitable to work on

A.C.supply 50 c/s. With all internal connections,

spreader tinned copper & complete erected in

existing 16 G.M.S. housing. ICS=100% of

ICU only Cat III (Make :-

L&T/Siemens/ABB/C&S/Havells)

261 Providing and erecting Approved make Earth 1.00 Nos. 5415.62

fault Relay suitable to mount with inter

connection suitable to following size of moulded

case circuit breaker having CT ratio & MCCB

rating as following along with shunt trip 220V

AC. with all internal connections & complete

erected in existing M.S.housing.. (3) 250 A -400

A , CT Ratio 1/400

262 Supplying & erecting approved make Four Pole 1.00 Nos. 22255.35

415V change over switch interior for panel

mounting with operating mechanism A.C.23 duty

confirming to IS for (F) 400A Cat.II (Make :-

L&T/Siemens/ABB/C&S/Havells/indoasian)

263 Supplying and erecting triple pole & neutral 9.60 Rmt 1961.42

440V /500V panel mounting Copper Busbars

with four equal Nos. of electrolyte bus having

current density not more than 1.6 Amp. / sq.mm

(Rated current /cross section area) duly

wrapped with colour insulating tape for phase

sequence of following current carrying capacity,

erected with necessary bus bar supports

/insulators, main cable socket to each bar,

erected in existing cubical panel with necessary

connections. (A) Suitable for 100 Amp. Capacity

264 (B) Suitable for 200 Amp. capacity 1.50 Rmt 3202.71

265 (D) Suitable for 400 Amp. capacity 2.50 Rmt 7319.47

266 Providing and erecting Miniature circuit breaker 26.00 Nos. 270.68

single pole 0.5A to 2A system and having

breaking capacity 10 KA to be erected in existing

box. confirming to IS 8828/1996 with ISI Mark

Cat.III (Make :-

L&T/Siemens/ABB/C&S/Havells/Altech)

267 Providing and erecting Miniature circuit breaker 216.00 Nos. 112.11

single pole 6A to 25A suitable to operate on

V A.C. system and having breaking capacity

KA to be erected in existing box. confirming to IS

8828/1996 with ISI Mark Cat.III (Make :-

L&T/Siemens/ABB/C&S/Havells/Altech)

Item Description of Item Quantity Unit Rate In Amount

268 Providing & erecting 240 V MCB double pole 123.00 Nos. 330.27

switch for motor & inductive load (C Curve)

having 10 KA breaking capacity & confirms to IS :

8828 in existing box having following capacity

(B) 40 Amp. Cat.III (Make :-

L&T/Siemens/ABB/C&S/Havells/Altech)

269 Providing & erecting 415 V MCB Four Pole for 4.00 Nos. 668.62

Motor & Inductive Load (C Curve) having 10KA

breaking capacity & confirms to IS :8828 in

existing box having following capacity (b)40

Amp. Cat.III (Make :-

L&T/Siemens/ABB/C&S/Havells/Altech)

270 (c)63 Amp. Cat.III (Make :- 131.00 Nos. 737.30

L&T/Siemens/ABB/C&S/Havells/Altech)

271 Sheets steel powder coated enclosure suitable for 91.00 Nos. 176.75

incorporating One/Two nos. MCB. (Make :-

L&T/Siemens/ABB/C&S/Havells/Altech)

272 Providing and erecting Sheet Steel powder 90.00 Nos. 355.52

coated MCB distribution board - flush / surface

mounted fitted with busbar, neutral link, earth

bar and DIN rail, Conforms to IS 8623-1 & 3, IEC

61439-1 & 3 without MCB to house appropriate

nos. of MCBs.(The DBs should be used of same

company of MCB to be used) suitable for (A)

single phase incoming and horizontal single

phase outgoing (a) single door (IP-30) (i)4 way

(Make :-L&T/Siemens/ABB/C&S/Havells/Altech)

273 (B) three phase incoming and single phase 12.00 Nos. 2913.85

horizontal type outgoing Per phase isolation

type (PPI) (b) sheet steel double door (ii)6 way

(Make :-L&T/Siemens/ABB/C&S/Havells/Altech)

274 Providing and erecting Approved make RCCBs 126.00 Nos. 2235.13

conforming to IS: 12640 and having sensitivity of

30 mA and Short Circuit withstand capacity of

KA and suitable for operation on single phase

240 V,50Hz. having characteristic of quick action

& tripping with all advance feature & do not

incorporate any electronic component. for

following Max. rating erected as directed (ii)

40Amps. DP Cat. III (Make :-

L&T/Siemens/ABB/C&S/Havells/Altech)

Item Description of Item Quantity Unit Rate In Amount

275 Providing and erecting Approved make RCCBs 90.00 Nos. 2235.13

conforming to IS: 12640 and having sensitivity of

30 mA and Short Circuit withstand capacity of

KA and suitable for operation on single phase

240 V,50Hz. having characteristic of quick action

& tripping with all advance feature & do not

incorporate any electronic component. for

following Max. rating erected as directed (ii)

40Amps. DP Cat. III (Make :-

L&T/Siemens/ABB/C&S/Havells/Altech)

276 Providing and erecting Annealed bare Copper 22.00 Kg. 794.87

wire 8 to 16 SWG.

277 Providing and erecting Pipe type earthing having 16.00 Nos. 368.65

150 cms.long and 2.5 cms. dia. galvanised iron

pipe with coupling and buch buried in specially

prepared earth pit complete with necessary

SWG earth wire.

278 For using salt and charcoal / coke as required for 16.00 Nos. 171.70

pipe type earthing.

279 Supplying & erecting earth pit of minimum bore 11.00 Nos. 4591.46

dia.150mm size approved make Earthing

Electrode consisting Pipe-in-Pipe Technology as

per IS 3043-1987 made of corrosion free hot

dipped G.I.Pipes having Outer pipe dia of 50mm

having 80-200 Micron galvanising, Inner pipe dia

of 25 mm having 200-250 Micron galvanising,

connection terminal dia of 12mm with constant

ohmic value surrounded by highly conductive

compound with high charge dissipation suitable

for following type of applications with chamber

and heavy duty cover. (A)(approved make OEM

has to submit test certificate including value of

earth resistance of installation duly stamped and

signed by agency and officer Incharge has to

ensure the value of earthing resistane mentioned

in test Certificate) & having back filling

compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 ohm / meter testing

as per IEC 62561-2017, Voltage drop:- < 1 volt at

no load & dry form, Sulphar content:- <2%(C)

Back fill Compound :- Earthing compound

should be capable to retain moisture for long

time Necessary test report must be submitted by

Agency. (a) For Electrical Installation up to 440V

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Item Description of Item Quantity Unit Rate In Amount

280 Providing & erecting weather proof, dust & 20.40 Smt. 10468.65

vermin proof, floor mounted front operated

indoor type cubical panel board necessary IP-42

and above protection as per approval from

engineer incharge made from 14 SWG thick CRC

M.S. sheet for outer body & doors, 16 SWG thick

CRC M.S.sheet for internal partitions with

necessary accesories, supporting angles/ flats

channel including cutting, bending, drilling,

welding, riveting with internal partitions & cable

alley as per requirements & instruction of

engineer-in-charge with erection of supplied

switch gears, BUSBARS, suitable size of inter

connecting PVC copper wire / copper-aluminium

strips, rubber grommets, rib, bakelite control

fuses/MCB for measuring instruments, earth bus

& earth bolts, foundation flange - bolts-base

Plates, sufficient nos. of hinged doors, handles

with locking arrangement and rubber

gasket,heavy duty end terminal

connection,danger notice board, necessary

ventilation, earthing strip complete. The Panel

shall be painted with epoxy powder coating.

(The rates excludes the cost of switchgears, bus

bars, inter connecting mains & Copper

Aluminium strips, meters, Fuses etc. The

dimension shall be measured excluding base

beams) The panel shall be supplied with

following approved manufacturers with

281 Providing, erecting, fabricating the M.S. structure 204.00 Kg. 77.77

as per requirement on site incorporating proper

size of M.S. angles,square,round, flats, bars,

channels, sections complete with cutting,

welding, grinding & finishing duly painted with

one coat of red oxide with erection on site as per

direction of engineer in charge with necessary

grouting, cementing, plastering & finishing

282 Providing and erecting XLPE (IS:7098) (I)-88 ISI 50.00 Mtr. 92.92

armoured cable Aluminium conductor for

KV. to be laid on wall with necessary clamps or

in existing trench /pipe of following size of

cables. (B) 2 core 6 Sq. mm (Make :- KEI/RR

Kabel/Havells/Polycab)

283 Providing and erecting XLPE (IS:7098) (I)-88 ISI 600.00 Mtr. 378.75

armoured cable multistrand Aluminium

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of

following size of cables (D) 3 1/2 core 70 Sq.

mm ( 35 Sq. mm 1/2 core) (Make :- KEI/RR

Kabel/Havells/Polycab)

core) (Make :- KEI/RR Kabel/Havells/Polycab)

Item Description of Item Quantity Unit Rate In Amount

core) (Make :- KEI/RR Kabel/Havells/Polycab)

core) (Make :- KEI/RR Kabel/Havells/Polycab)

287 Providing and erecting XLPE (IS:7098) (I)-88 ISI 650.00 Mtr. 126.25

armoured cable multistrand / Solid Aluminium

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of

following size of cables (B) 4 core 6 Sq. mm

(Make :- KEI/RR Kabel/Havells/Polycab)

288 Making trench in soft soil of suitable width of 90 590.00 Mtr. 55.55

cm deep for laying cable or locating the fault all

over the run and back filling the same and

making the surface as normal ground.

289 Providing & laying approved make Double 590.00 Mtr. 62.62

walled corrugated pipes (DWC) of polyethylene

(conforming to IS 14930 II) with necessary

connecting accessories of same material at

required depth in existing trench for laying of

cable. below ground / road surface for enclosing

cable (A)50 mm outer dia

290 Providing and, fixing heavy duty flange type 52.00 Nos. 38.38

brass cable gland with rubber ring for PVC

insulated armoured cable complete with out

going tails, insulating tape etc for following size

of cables. (B) 2 to 4 core 6 Sq. mm

291 Providing and, fixing heavy duty flange type 20.00 Nos. 103.02

brass double compression type cable gland with

rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc

for following size of cables. (C) 3 & 1/2 core

295 Solder less crimping type Aluminium lugs 208.00 Nos. 6.06

conforming to IS suitable for cable of following

size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/

cadmium plated nut bolts in an approved

manner. (A) 1.5/ 2.5/4/6 Sq.mm

Item Description of Item Quantity Unit Rate In Amount

300 Providing and fixing approved make Perforated C 540.00 Rmt 360.57

type cable tray. Made from sheet steel. The cable

tray should be single or double bended as per

required and as per IS 2062/1079 and shall be

coated with hot dip galvanizing as per IS

2629/4759. with max 17.5% perforation with

coupler plate / Fish plate and GI hardware like

nut - bolt and washers etc. erection with

necessary support( included) as per

Specification and as per instruction of engineer in

charge.. (2) 100 X 50 X 1.6 mm Thick

302 Providing and fixing approved make Ladder type 20.00 Rmt 287.85

cable tray. Made from M.S sheet. The cable tray

should be bended as per IS 2062/1079 shall be

fabricated of double bended channel section

longitudinal members with single bended

Channel section. Rungs of members welded to

the base of the longitudinal members at 250 mm

c/c spacing . as per IS and shall be coated with

hot dip galvanizing as per IS 2629/4759. with

coupler plate / Fish plate and GI hardware like

nut - bolt and washers etc. erected on existing

support as per Specification and as per

instruction of engineer in charge.. (2) 200 X 50 X

303 Providing and erecting Approved make Ceiling 239.00 Nos. 1596.81

fan with double ball bearing ISI mark with

condenser A.C. 23OV.50 c/s.1200 mm. sweep

complete, canopy erected on existing hook or

clamp with earthing. [Make shall be approved by

Engineer in charge] (Make :-

Bajaj/Crompton/Havells/orient/Usha)

304 Supplying and erecting 19 / 20 mm. nominal 239.00 Mtr. 108.07

bore Medium Class M.S. Pipe down rod erected

duly painted for fan complete with proper

insulation without leakage and earthing.

305 Supplying & erecting fan hook box of 10 mm 239.00 Nos. 108.07

M.S. round bar bounded to the RCC bars up to

50mm length each side and pierced through a

Gauge M.S. box / Heavy Duty PVC box complete

erected concealed in Ceiling with necessary

306 Supplying & erecting approved make low noise 18.00 Nos. 1703.87

decorative exhaust fan having square frame ABS

body with inbuilt lowers & square frame. 200mm

with 1350RPM Cat.II (Make :-

Bajaj/Crompton/Havells/Prient/Usha)

Item Description of Item Quantity Unit Rate In Amount

307 Supplying & erecting single phase approved 27.00 Nos. 3937.99

make industrial exhaust fan suitable for medium

duty ring mounted low noise operation suitable

for medium duty having following dia size and

maximum speed in RPM [E] 450 mm dia

RPM Cat.II (Make :-

Bajaj/Crompton/Havells/Orient/Usha)

308 Supplying and erecting approved make 26.00 Nos. 6874.06

Octagonal pole made from HR sheet steel. The

pole should be made as per IS. and shall be

coated with hot dip galvanizing as per IS

2629/2633/4759, suitable suspend local wind

speed with integral Junction box consist of

terminal plate of min 6mm Hylam sheet,

standard profile 35mmX7.5mm Din-Rail for MCB

Mounting, stud type terminal and arrangement

for cable termination to be erected With Suitable

foundation (Included) as per details given by

manufacturer considering site requirement. (C)

Mtr. Long 70 mm Top X 130 mm bottom dia,

mm thickness with 200mmX200mmX12mm

base plate, 4-M16 Bolts and 600mm long with

necessary G.I. J Bolts .Approx Pole weight 46 kg

Transrail/Valmont/Bajaj/Jindal/Ambika)

309 Supplying and erecting Street light pole bracket 26.00 Nos. 491.87

comprising main B Class GI pipe of

cm/require outside dia. complete with suitable B

Class G.I. sleeve tubing of approx. 45cms.length

and suitable for 76.5mm/80mm/require size of

pole top having nuts and bolts for fixing the

brackets and having spread of 0.5 mtr. Length

with 110 deg.with vertical plane and suitable

welded stiffener reducer and nipple with check

nut complete painted with one coat.of Red oxide

/ PU base primer and two coats of Aluminium /

PU paint. paint with following nos of arms. [A]

Single Arm bracket 0.5 Mtr

Item Description of Item Quantity Unit Rate In Amount

310 Supplying & erecting IP 55 grade following size 2.00 Nos. 3595.60

section pillar fabricated from joint less M.S. Sheet

with angle iron legs made from jointless M.S.

Angle with cable clamps to be buried in ground

to have appropriate erection to work uniform

until erected with cement concrete foundation

and 45 cm high bricks work finishing with plaster

etc. hinged double door internally supported on

both side, with internal and outside looking

arrangement with look and keys in duplicate 35 x

35 x 5 mm M.S. Angle of Two Nos. one is welded

and other with nut and bolt for erecting Bakelite

sheet. Painting the Section Pillar inside and out

side with three tank powder coated paint.

section pillar roof should be without joint with

water leakage proof & tested as per IP 55 test &

followed by IS 2147 of 1962 (B) 75 X 60 X 45 cm

section pillar fabricated from 16 Gauge MS Sheet

with angle iron legs 45 cm long made from 35 X

35 X 5 mm thick MS angle.

311 Supplying & erecting approved make Digital time 2.00 Nos. 3168.37

switch having lithium cell 6 years operative and

operate battery backup 1 channel day clock with

14 memory programme, suitable to operate on

240V + 5%, 16A with, floating contacts Minimum

switching setup time 1 minimum & LCD display.

Also comprised permanent ON/OFF switching.

Programming switches & housed in fire proof

thermoplastic enclosure & transparent cover

erected as required with necessary connection

erected as directed.

312 Supplying & erecting power contactor, AC3 duty 2.00 Nos. 2782.55

for time switch complete erected as per direction

Cat III (D) 4 pole 440V 40 Amp.

313 Supplying and erecting wall mount speaker with 6.00 Nos. 2569.44

rated power of 30 watt/power tapping

30/15/7.5 watt available,opening angle

degree H * 77 degree V ,sound pressure level

dB ,frequency response of 70Hz to 20KHz

[[Approved by Competent Authority i.e. not

Below the rank of Executive Engineer ]

Item Description of Item Quantity Unit Rate In Amount

314 Providing and erecting cordless microphone with 2.00 Nos. 5135.85

UHF Diversity handheld wireless

microphone/caller wireless complete with

receiver and transmitter unit,Cardiod ,polar

pattern,dynamic microphone,LCD display for

battery and frequency status and information

preset channels,with compatible groups of

channels,14 hrs.battery life,frequency response

80Hz to 18KHz.,RF sensitivity <1.0 Uv,image

rejection > 55 dB,dynamic range >95 dB and

receiver having 32 channels,S/N ratio>100

dBA,Dynamic range>95 dB,distortion<1%

[[Approved by Competent Authority i.e. not

Below the rank of Executive Engineer ]

315 Supplying & erecting Amplifier having following 1.00 Nos. 6249.88

Power Output :100 W (RMS):(130 W Max.)

inputs :5 Mics & 2 Aux.

frequency Response :50-15000 Hz+3db

Tone Controls :Cut & Boost type

Speaker Matching :4-8-ohms 70- 100 V line

LED Meter :5 LED Array.

The amplifier suitable to operate 240V A.C.&

volt D.C. (Battery) with automatic changeover

from AC to Battery operation, duly protected by

wrong Battery Polarity connection. [[Approved

by Competent Authority i.e. not Below the rank of

Executive Engineer ]

Item Description of Item Quantity Unit Rate In Amount

316 Supplying & erecting Mixing Console having 1.00 Nos. 18386.04

channels, Audio mixer with. Echo facility for live

performance, Auditorium & stadiums, having

following features & facilities. [[Approved by

Competent Authority i.e. not Below the rank of

Executive Engineer ]

(a)input Channels :- Each channel has separate

6.25mm size balanced phone jack for mike &

line for balanced & unbalanced signals.

(b)Individual gain control for sating optimum

level for minimum noise.

(c)BASS, MID & TREBLE ‘ controls Separately for

each input channel.

(d)ECHO control for each channel

(e)PAN control for echo channel for left or right

(f) AUX Control : To control , level of the channel

in final mix to AUX sound output

(g)Channel ON/OFF switch

(h)ECHO Section :- ECHO, reverb & Chorus effect

can be added to all input channel by different

setting of Delay, Reverb & Level control.

(i)Tape section

(j)Aux. send & return For sending Pre-feeder

output of channel for monitoring or adding a

special effect unit.

(k)Mono / Stereo output controls

(L)Master faders to control over left & right

317 (g) Outputs, Line Output Line Output Low : - 0.00 0.00 0.00

10 dB / -2 dBM Line Output High : 0 dBM /

(h) S/N ratio Line Output Level : > 70 dB (0 dB,

The Console shall be mounted on standard Rack,

The channel of following numbers. (A)

Channel Audio Mixer with ECHO

318 SITC of 3LCD Lamp based projector having wxga 3.00 Nos. 33895.60

(1280x800) or better resolution with minimum

white brightness of 3800 lumens and color

brightness of 3800 lumens. The projector should

have minimum 1HDMI,1VGA input. Having

contrast ratio of 15000:1 or more. the projector

should have auto vertical key stone correction of

+/- 30 degree and Manual Horizontal of +/-30

degree. the projector should have optical lens,

throw ratio 1.30-1.56:1. Zoom Factor of 1.2. Lens

focus Manual having focal length 16.9mm to

20.28mm. projector should have features like AV

mute slide, quick corner and split function and

should support wireless functionality with inbuilt

wifi or wifi dongle. [Approved by Competent

Authority i.e. not Below the rank of Executive

Item Description of Item Quantity Unit Rate In Amount

319 SITC of 100 inch Self Lock MW (7 x 5) Instalock 3.00 Nos. 3810.73

Slow Retraction Screen, Aspect Ratio-4:3

[Approved by Competent Authority i.e. not Below

the rank of Executive Engineer ]

320 Providing and erecting Inverter based approved 8.00 Nos. 51666.55

make split air-conditioning unit consisting of

condensing unit with variable speed fan motor,

inverter type hermetically sealed rotary

compressor with accessories etc. duly connected

separately erected evaporating unit and blower

motor with its accessories by means of extra

supplied proper insulated copper tubing,drain

PVC pipes suitable for ( cost includes Eco

Friendly green gas charging and 15A plug top &

Remote Control & MS Stand) with necessary core

cutting. (1)For ISEER Range (KWH/KWH)(3.1 to

3.99) (C) for 1.7 to 2 ton capacity (Make :-

Voltas/Bluestar/Hitachi/Daikin/AKABISHI)

321 Supplying and erecting insulated pair of soft 25.00 Rmt 965.56

copper tubing open or concealed including

power and control cable,necessary PVC drain

pipes for Split AC machine up to 4 TR capacity

322 Providing & erecting water cooler having storage 4.00 Nos. 55893.40

capacity 150 Ltr. & cooling capacity 150 Ltr.per

hour @ an ambient temp of 45˚ C. The outlet

temp. of the water should drop by 15˚C within a

hour, The water cooler should be comprising of

hermetically sealed compressor, fan motor,

condensing unit, water tank surrounded by

evaporating, coil, thermostats, relay etc.complete

with necessary inlet & outlet connection. The

body of water cooler will be made from Stainless

Steel. (Make :- Voltas/Usha/Bluestar)

323 Supplying & erecting reverse osmosis (RO) 4.00 Nos. 77891.20

water purification system with M.S. powder

coated pedestal frame, prefilter housing carbon

filter suitable buster DC pump, auto low & high

pressure switches with following size of LPH

capacity & erected as directed [D] 100 LPH with

1 phase / 3 phase Raw water pump of 500LPH @

2.5kg/cm2 - (1N0 - Kirloskar /CRI/Lubi), Dual

media filter 10"x54" - (1 No), Micron cartridge

filter 20" x 2.5" ( 1No), High pressure pump

500LPH @ 10kg/cm2 - (1No - Shimge /CRI

/Lubi), RO Membrane housing with RO

membrane of 40*40 - (1No), RO pressure tube 4"

x 1E - ( 1No), 0 - 1200LPH Rotameter -(2 Nos),

with Recovery Rate 50%.

Item Description of Item Quantity Unit Rate In Amount

324 Supplying and erecting approved make panel 11.00 Nos. 1275.63

mounting type Digital Voltmeter having 3 digits

LED display, 0 to 750 AC Volts range erected on

existing panel board with all connection, wiring

etc .with manufacturers calibration certificate.

325 Supplying and erecting approved make panel 11.00 Nos. 1558.43

mounting type Digital Ammeter having 3 digits

LED display, external CT operated, calibrated for

0 to 1000 Amps suitable to operate on 500 Volt

AC, erected on existing panel board with all

connection, wiring etc .with manufacturers

calibration certificate.

326 Supplying and erecting Ammeter / Voltmeter 22.00 Nos. 317.14

selector switch for 3 phase AC Supply 500 V on

existing panel board with necessary connections.

327 Providing & erecting L.T. Current Transformer 33.00 Nos. 274.72

with bar primary 50/5 to 1000/5 ratio 15 VA

burden erected in existing CRCA box duly

secured with insulating materials connected to

328 Supplying and erecting approved make suitable 33.00 Nos. 43.43

panel indicator LED type lamp, lens cover,

complete erected with necessary connections.

329 Supplying & erecting carbon dioxide (CO2) fire 13.00 Nos. 8671.86

extinguisher user of following capacity with

necessary clamps made from 50 x 6 mm M.S. Flat

with nut & bolts grouted in wall complete. [B] For

5.5 / 6.5 KG Capacity

330 SITC of Vertical Air Termination Solid aluminium 2.00 Nos. 9416.23

with Base- 10 mm dia and 1000 mm long. Air

Termination Base tested for conditioning, Ageing

Test & Lightning impulse current withstand test:

100 kA of 10/350µs waveform in an accredited

Third party laboratory as per 6.3 & 6.4 of IEC

62561-1 2017 protocol with MAST 34mm dia

3000 mm long- Cold Galvanized

Item Description of Item Quantity Unit Rate In Amount

331 SITC of 8 mm dia solid Aluminium Conductor for 80.00 Mtr 299.97

roof top mesh grid and tested as per IEC 62561-

2 conducted in the Govt. accredited thirty party

laboratory to meet the requirement of IS/IEC

62305 with Required Accessories - Aluminium

Holding clamp at every 1 mtr distance,

Aluminium/SS cross splicer at every crossing of

Alu. conductor, Expansion piece with connectors

at every 20 mtr distance, Aluminium straight

Splicer to connect conductors. All Accessories

should be tested as per IEC 62561-1 2018 Cl.

for conditioning & Ageing Test & 6.4 for

Lightning impulse current withstand test: 100 kA

of 10/350µs waveform(Ageing & Electrical test )

conducted in a sequence manner & tested in the

Govt. accredited Third party laboratory to meet

the requirements of IS/IEC

332 SITC of 10 mm MS Round Solid Conductor having 80.00 Mtr 728.21

smooth surface Should be tested and use

exclusively for lightning protection (Vertical

Riser/Down Conductor which shall be concealed

in Column OR Flushed on) to meet the

requirement of IS IEC 62305 With Accessories -

Earthing stud of dimension SS-75mm OD plate

with 10mm dia tail connector used in structural

steel ring earthing system to meet the

requirements of IS/IEC

(For Interconnecting the Column and the Terrace

AL Conductor / Strip/Flat), SS Cross Connector to

connect Earth fixing point to vertical

raiser/Down conductor, SS Straight Splicer at

every 4 Mtr to connect MS conductor in column,

Bonding /Rebar Clamp at every 3 mtr suitable for

interconnecting round conductor with

reinforcement inside the concrete for structural

earthing system, SS connector -To connect

external conductor 8- 10 mm with earth fixing

point. All Accessories should be tested as per IEC

62561-1 2018 Cl. 6.3 for conditioning & Ageing

Test & 6.4 for Lightning impulse current