Restoration of rain damages to LWSS Seola Manjhot Pandoh in Tehsil Sadar District Bilaspur (SH Construction of pump house 45.41 Sqmt and construction of boundary wall with fencing panel for pump house).

Amount

Excavation in foundation and trenches (for pipe and pits) in all kinds of soil such as pick jumper work, including saturated soil stacking the excavated soil with all leads and lifts and clear from the edge of excavation and then returning the stacked soil in 15cm layers, when required into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed within all leads and lifts including dressing of beds and sides and preparation of un metal led /metal led/ paved surfaces to its original conditions including shoring, strutting, timbering and dewatering whenever is required. Providing diversions for traffic, night signals fixing caution board crossing over trenches for access to houses complete in all respect and to the entire satisfaction of the Engineer-in-charge Pick and jumper work.

Providing and laying cement mortar 1:6:12 (1cement: 6sand: 12 graded stone aggregate 40mm nominal size) excluding the cost of centering and shuttering in foundation and plinth and to the entire satisfaction of the Engineer-in-charge.

Random rubble masonary / polygonal rubble masonry ( un coursed brought to courses) with hard stones of approved quality in foundation and plinth includinglvelling up with cement concrete 1:6:12 (1cement: 6sand:12 graded stone agg.20mm nominal size) at plinth level in cement mortar 1:6 (1cement: 6sand) within all leads and lifts complete in all respect

Providing and laying cement mortar 1:2:4 (1cement: 2sand: 4 graded stone aggregate 40mm nominal size) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in:-.

Foundation footing bases of columns and the like and mass concrete within all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Brick work using common burnt clay building bricks 2nd class in super structure above plinth level upto floor two level in cement mortar 1:6 (1cement: 6sand) in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Providing and fixing pressed steel doors frames manufactured from commercial mild steel sheet of 1.25mm thickness including hinges jamp lock jamb bead and if required angle threshold of mild steel angle of section 50x25mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with splita and tails to each jamp including steel butt hinges 2.5mm thick with guards, lock strike plate and shock as specified and applying a coat of approved steel primer after pretreatment of the surface as directed by the Engineer-in-charge. Profile-A

Providing and fixing wood paneled glazed or paneled and glazed shutters for doors, windows and clear store 40mm thick windows including bright finished black enameled iron with necessary screws with second class deodar wood 40mm thick in all l eads and lifts and to the entire satisfaction of the Engineer-in-charge.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens ballies, height of propping and cent ring below supporting floor to ceiling not exceeding 4 mtr and removal of the same for in-situ reinforced concrete and plain concrete work in:-

Flat surfaces such as soffits of suspended floor landings and the like up to 200mm thickness and to the entire satisfaction of the Engineer-in-charge.

Providing and laying cement concrete 1:2:4 (1cement:2sand:4 graded stone aggregate 20mm nominal size) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in :-

Suspended floor roofs landing shelves and their supports balconies, beams girders breasumers and cantilevers up to floor two level.

Providing tor steel reinforcement for RCC work including bending binding and placing in position complete in all depths and heights and to the entire satisfaction of the Engineer-in-charge.

Half brick masonry in common burnt clay building bricks in cement mortar 1:4 (1cement: 4sand) extra half brick masonry in super structure for above plinth level uptofloor two level and to the entire satisfaction of the Engineer-in-charge.

Pointing on brick work with cement mortar in 1:3 (1cement: 3sand) in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Providing and laying brick tiles over mumty roof grouted with cement mortar 1:3 (1cement: 3sand) over a 12mm layer of cement mortar 1:3 (1cement: 3sand) and finished neat over RCC slab (stoped protion)in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

6mm cement plaster to ceiling cement mortar 1:3 (1cement: 3 sand) in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

15mm cement plaster in single coat of rough side of brick/ concrete/ stone walls for interiorplastering in all depths and the height including arises internal rounded angles exceeding 80mm in girth and finished even and smooth in cement mortar 1:6 (1cement: 6sand) in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

20 mm cement plaster in single coat of rough side of brick/stone masonry for interior plastering up to floor two level including arises, internal rounded angles, chamfers and / or rounded angles not exceeding 80 mm in girth and finished even and smooth CM 1:6 (1cement: 6sand).

Providing and fixing MS grills of required pattern in wooden frames of windows etc. with MS flat square or round bars with rounded headed bolts and nuts or by screws complete in all respect within all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws 2nd class deodar wood 40mm thick including carriage of material in all leads & lifts.ist class deodar wood and to the entire satisfaction of the Engineer-in-charge.

Stone / boulder filling under floor / behind the retaining wall in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Providing plinth protection 50mm thick in cementr concrete 1:3:6 (1cement: 3sand: 6 graded stone agg. 20mm nominal size) including finishing of the top surface of concrete smooth in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Constructing course rubble hammer dressed ‘U’ shape open surface drain with side wall,15x22cm in cement mortar 1:6 (1cement: 6sand) and inside plastering with cement plaster 1:3 (1cement: 3sand) incuding earth work and laying 10cm cement concrete in 1:5:10 (1cement:5 sand:10 graded stone agg.) of 40mm nominal size and 7.5cm cement concrete 1:2:4 (1cement:2sand: 4 graded stone agg. of 20mm nominal size and finished with a floating coat of neat cement concrete as per standard design.

Providing 40x3mm flat iron hold fast 40cm long including fixing to frames with ten millimeters dia of bolts nuts and wooden plug and embedding in cement concrete block 30x30x15, 1:3:6 (1cement:3sand: 6 graded stone) agg. 20mm.

Providing and fixing MS fan clamp (type-I of 16mm dia M.S barbent to shape with hooked ends in RCC slab during laying including painting the exposed portion of loop all as per standard design complete in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

White washing with lime on undeocrated walls surface ( two coats) to give an even shade including thoroughly brooming the surface dirt dust mortar dirt and other foreign matter in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Distempering with dry distemper or approved brand and manufacture (two coats) and or required shade on undecorated wall surface to give an even shade over and including primer coat of whiting after, thoroughly brushing and surface free from mortar dropping and other foreign matter including preparing the surface even and sand papered smooth.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces (two coats) to give an even shade after throughly brushing the surface to remove all dirt and remains of loose powdered material in all leads and lifts.

Providing and fixing anodized aluminium fittings of anodized transparent and shade with necessary screws etc. complete sliding door bolt (250x16mm)

Providing and fixing anodized aluminium fittings of anodized tranaparent and shade with necessary screws etc. complete tower bolt (200x10mm)

Providing and fixing anodized aluminium fittings of anodized transparent and shade with necessary screws etc. complete handle (100mm)

Painting two coats (excluding priming coat) on new wood and wood based surface with ready mixedpaint brushing the give an even shade including cleaning of alldirt dust and other foreign matter and sand papering and stopping with ready mixed paint other than white in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Pre-cast terrazzo tile 20mm thick with marble chips of specified sizes laid in floors treads of steps and landings on a bed of 25mm average thickness of cement mortar 1:6 (1cement: 6sand) jointed with neat cement slurry mixed withpigment to match the shade of tiles (wherever required) including rubbing and polishing complete with tiles of following shades within all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Providing and laying cement concrete 1:3:6 (1cement: 3sand: 6 graded stone agg. 20mm nominal size) excluding the cost of form work in foundation and plinth in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Providing and fixing and manufacturing MS gate-1 made of MS flat 50mm x6mm2.50x1.50 mtr in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Providing fixing and manufacturing fencing panel made of MS conduct pipe 32mm dia 1.50x1.00 mtr with wire meash 10 SWG 90x30mm in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

15mm cement plaster in single coat of rough side of brick/ concrete/ stone walls for interiorplastering in all depths and the height including arises internal rounded angles exceeding 80mm in girth and finished even and smooth in cement mortar 1:3 (1cement: 3sand) in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

M/S SADA RAM BROTHERS

Sanjay Saini

Javed Khan

prakash thakur