CA NO. CWE BLY / GE(E)/ 103 OF 2021-2022 PROVN OF 01XGUARD ROOM WITH SENTRY POST FOR 07XOR AND COVERED SCOOTER/ CYCLE SHED NEAR MAIN GATE OF MTN DOU UNDER GE(E) BAREILLY

Amount

M&L for excavation in trenches not exe 1.5 m width or depth and getting out in hard/dense soil etc complete all as specified and directed.

M&L for excavation in trenches not exe 1.5 m width or depth and getting out in soft/loose soil etc complete all as specified and directed.

M&L for excavating over areas, n exc 1.5m deep and getting out Hard /dense soil complete all as specified and directed.

M & L for Surface dressing n exc15 cm deep in hard/dense soil etc complete all as specified and directed.

Returing filling in including spreating levelling, watering and well raming in llayers not exe 25cm thick etc complete all as specified and directed.

Removing excavated materials not exc 50m and depositing where directed. at a level not exceed ng 1.5m above the starting point in soft/loose soil etc complete all as specified and directed.

M &L PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation etc complete all as specified and directed.

M&L for reinforced cement concrete M-25(design mix) as in foundation footing , plinth beams etc complete all as specified and directed.

M&L for reinforced cement concrete M-25(design mix) as in beams, lintels etc complete all as specified and directed.

M&L for re-inforced cement concrete (nominal mix) type B1 (1:2:4) using (20mm graded stone aggregate) in Chajjas etc complete all as specified and directed.

M&L for reinforcement cement concrete M-25(design mix) as in columns, piers, pillars, struts, etc complete all as specified and directed.

M & L Reinforced cement concrete (design mix M-25) usinng 20mm graded stone agg as in slab supported on walls beams and columns in floors roofs landing balaconies etc complete all as specified and directed.

S&F Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.90 mm dia etc complete all as specified and directed.

S&F Mild steel TMT bars 5mm dia and over upto and including 10 mm dia in stirrups,spaces and binders and all as specified and directed..

S&F form work to sides of concerte, foundation, footings base of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to butter etc complete all as specified and directed.

S&F Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc complete all as specified and directed.

Form work to sides and soffits of floor or roof beam, beam hings, girders bressume, lintles, contilevers, shelves including support over lungs etc also splays between floor and beams etc complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide.

M & L Treating the bottom and sides of excavation,plinth protection and top surface of filled earth at the rate of 5 liters of emulsion per square metre of surface area etc complete all as specified and directed.

M & L Treating the back fill incontact with foundation at the rate of 7.5 litres of chlorophyriphas emulsion persquare metre vertical surface etc complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) etc complete all as specified and directed.

S&F sliding windows of aluminium alloy powder coated, window and frame with movable shutter ( sliding on minimum two PVC roller of best quality, for each shutter ) on tracks ( Three tracks with mosquito proofing) and glazzing with and including 5.00 mm thick tinted glass fixed with neoprene rubber gasket with aluminium beading, clips,frame made with aluminium section as appended below- (i) Window frame :63x35mm X 1.48 mm thick for two tracks. (ii) Top/bottom rail and style / rail of shutter : 19x38x1.48mm thick and over. (iii) Aluminium beading - 0.7mm thick (IV) stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperature 1.40mm and fixed in aluminium window or alongwith F/Y section fixed with aluminium wire staples complete. (iv) Aluminium fittings such aluminium handle 100mm long (v) Making good of wall surfaces to match with existing surfaces complete all as specified and directed..

S&F Powder coated aluminium ventilators box type with louvers & wire mesh fixed with neoprene rubber gasket, aluminium beading, clips. Frame made with powder coated aluminium section of size as appended below (i) frame :45.2mm x35mm X 1.15 mm (ii) Aluminium beading - 0.7mm thick (iii) Glass louvers depth 6 inch. Blade Angle: 38 degrees and thickness of blade 2.02 mm with 106.25 mm spacing. (iv) Aluminium neccessary fittings complete as required. (v) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed..

S&F for 2nd class hard wood plain, solid, straight chowkats and frames for double shutter, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed.etc complete all as specified and directed.

S&F 2nd class HW Factory made 35 mm thick Glazed and skeleton shutter, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats.etc complete all as specified and directed.

S&F stainless steel wire cloth, 0.56 mm nominal dia of wire and average with of aparture 1.18 mm and fixed with stainless steel wire staples etc complete all as specified and directed.

S&F Plain framed, panelled shutter 40mm thick (any number of panels) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated etc complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.

S&F Factory made solid panel PVC prelaam colour door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 100mm butt hinges, extruded aluminium alloy with galvanised mild steel hinges pin, anodised and fixed type C-21 all as specified and directed..

S&F 150mm size aluminium handles, cast type anodised completed all as specified and directed..

S&F for ISI marked 150mm long aluminium alloy, anodized,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

S&F for ISI marked 300mm long aluminium alloy, anodized,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extrudedsections or cast-aluminium alloy and fixed.

S&F 150mm long extruded Aluminium anodised,barrel tower bolts of extruded section and fixed etc complete all as specified and directed.

S&F 200mm long extruded Aluminium anodised,barrel tower bolts of extruded section and fixed etc complete all as specified and directed.

S&F 375mm, Brass rat tail rod patttern springs includding roller and roller platewith fixed to wooden/pressed steel frame chowkats with flat iron 40x3mm size 75 cm long with necessary bolts, etc complete all as specified and directed.

S&F 20 mm dia stainless steel 1.0 mm thick fancy type droppery rod with decorative design matching brackets as approved and knobs (lattu) or end bracket as required incl fitting with 80 mm long SS screw with 75 mm long wooden gitty of appropriate c/s in each end & intermediate support etc complete all as specified and directed.

M &L Hard core of gauge n exc 63mm, deposited, spread and levelled in layers n exc 15cm thick broken stone, water and rammed to a true surface etc complete all as specified and directed.

M& L 75 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base floor / pavings complete all as specified and directed.

M & L for 100mm thick plain cement concrete 1:4:8,type B-2, (using 40 mm graded stone aggregate) as in sub base of floor, finished cement concrete surface even and rough complete all as specified and directed..

M & L 25 mm thick PCC (1:2:4) type B1(20 mm graded stone aggregate) as in floor rough finished to receive top layer etc complete all as specified and directed.

M&L 15mm thick rendering in cement mortar 1:4 to brick masonry wall surfaces or on other than fair faces of brick wall surfaces finished fair & even without using extra cement for fixing tiles etc complete all as specified and directed.

M&L screed bed or bedding layer 15mm thick in CM 1:4 for laying glazed tiles in floors etc complete all as specified and directed.

M&L Screed bed or bedding layer 20mm thick in CM 1:4 for laying glazed tiles in floors etc. complete all as specified and as directed. by the Engineer-in-Charge

M & L for 7 mm thick glazed coloured ceramic tiles ( square/ rectangular) with border , area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed..

M & L for Non-Skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and directed.

M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete to get mirror finish etc complete all as specified and directed.

M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete to get mirror finishetc complete all as specified and directed.

M&L Granite 20mm thick (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:4, for laying floor finishes/tiles etc complete all as specified and directed.

M & L cement concerte 75mm thick 1:3:6 type C-1 (using 20mm graded) as in plinth protection, finished smooth and even without using extra cement etc complete all as specified and directed.

S&F for 15mm bore `Medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed..

S&F for 20mm bore `Medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floorsetc complete all as specified and directed.

S&F for 25 mm bore `Medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floorsetc complete all as specified and directed.

S&F Vitreous China table top wash basin of suitable size including SS bottle trap, HDPE waste pipe including fixing on counter with SS waste coupling complete all as specified. Model : Cat No 91072 Orchid of Hindware , Parryware Cat No C0483, Cera Cat No FLS-WHT-0575

S&F vitreous china squatting pan of orrissa pattern long pan size 580 x 440 mm white with "P"or "S" trap size 100 mm dia front or back inlet and integral foot rest any pattern (excluding flushing cistern and flush pipe) including provn of lime concrete bedding complete all as specified. Make Hindware / parryware or equivalent .

S&F PVC low level flushing cistern 10 ltrs cap white / coloured incl internal fittings brackets clamp and 32mm dia PVC flush pipe complete all as specified and directed. incl taking down low level cistern complete.

S&F fancy type sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with CP bracket gaurd and railling 60 cm long complete all as specified. Make Jaguar or equivalent.

S&F CP Tubular Towel Rail 600mm long,20mm dia,D type fixed with and including Chromium plated brass screws and wooden/plastic cleats etc complete all as specified and directed.

S&F fancy type 150mm size square brass CP shower rose all as specified.Make hindware/ cera or equivalent

S&F for 15 mm bore fancy type chromium plated Bib taps with wall flange cast copper alloy with capstan head sc-rewed down screwed for iron pipe or for brass ferrule and fixed, complete all as specified and as directed. .

S&F for 15mm stop cock cast copper alloy wall flange screwed down high pressure with capstan head fancy type chromium plated with long shank (concealed type).

S&F for angle cock cast copper alloy CP wall flange screwed down high pressure with capstan head fancy type chromium plated (Bore dia of pipe in 15mm)

S&F PVC pipe connection 450mm long 6kg F/sqcm pressure rating with flare nuts on both ends suitable for 15mm dia pipe etc complete all as specified and directed.

Supply and fixing for ISI marked Pillar Tap Swan neck fancy type of 15mm bore dia, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S&F 75mm bore dia cast iron nahani trap, with grating incl jointing to waste pipe fixed in Cement concrete 1:2;4 type B1 etc complete all as specified and directed.

M&L for PVC ( SWR ) Gully trap 125/110 mm , with grating incl jointing to waste pipe fixed in Cement concrete 1:2;4 type B1 complete all as specified and as directed. .

S&F PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fitting etc complete all as specified and directed.

S&F PVC (SWR) 110mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fitting complete all as specified and directed..

S&F 110 mm bore PVC (SWR) bends any radius,complete all as specified.

S&F 75 mm bore PVC (SWR) bends any radius,complete all as specified.

S&F PVC (SWR) junction single, (Single T) equal or unequal for 75 mm bore pipe.

M & L for 1000 Litres three layers rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) with lid hoisted and fixed in position all as specified in SSR Part-I complete all as specified and as directed. .

S&F Gun-metal, globe or gate valves 20mm bore with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed..

S&F Gun-metal, globe or gate valves 25 mm bore with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed..

S&F ball valves,high pressure of PTMT of 15 mm dia with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed.(Min weight 15 mm dia 142 gms)

M & L for applying cement slurry over existing roof surface @ 3 Kg/Sqm incl mix with water proofing liquid @ 0.15 ltr per 50 kg cement bags as per manufactures instructions complete all as specified and directed..

Supply Integral water proofing Liquid of Dr fixit/sika/Fosroc

M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:4, over RCC roof slabs for laying water proofing treatment mixed with using water proofing liquid @ 150 ml per bag of cement complete all as specified and directed. by Engineer-in-Charge.(Note : Water proofing liquid shall be measured and paid separately)

M&L 15mm thick rendering in cement mortar 1:4 to brick masonry wall surfaces or on other than fair faces of brick wall surfaces finished fair & even without using extra cement complete all as specified and directed.

M&L rendering 15 mm thick in CM 1:6 on brick masonary wall surfaces or on other than fair faces of brick masonry finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 5 mm thick in CM 1:3 as on concerete surface on ceilings finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing newly plastered walls surfaces and applying two coats of oil bound distemper over and including 1mm thick wall care putty complete all as specified and directed.

M&L for preparing newly plastered walls surfaces and applying two coats of cement base paint over a coat over and including 1mm thick cement based wall care putty complete all as specified and directed.

M&L for preparing newly plastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed.

M&L for Preparation of new steel surfaces of any description, over 10cm in width or girth not otherwise described two coat of synthetic enamel paint over a coat of red-oxide primer complete all as specified and directed.

M&L for Preparation of new wooden surface applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed..

.S & F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

S & F .Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

S&F mild steel framed work in roof trusses (framed),trussed, purlins, crane gantries, rail & fastenings and heavy brackets framing (Beam, tee, angle, channel, or flat sections) including distance pieces, cleats etc. confirming to Fe-410 (Gde E-250) Complete all as specified and directed.

S&F MS work as in nosing to steps including embeding in concrete and screweing, wind tie for roof including securing boltingpost and struts in fencing including cutting tops as directed., drilling holes, notching for wire , flat iron fillets including all necessary drilling, bolting or rivetting etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M & L for 50mm thick PCC type A-1, 1:1.5:3, (using 12.5 mm graded stone aggregate) including 20mm thick waterproof topping ( 10% of weight of cement) as in floor and paving, finished the surface even and smooth without using extra cement with impression of expanded metal when the concrete is green complete spike rolling all as specified and directed.

M&L for aluminium deviding strips of 38mm width and 15mm thick & inserted in position to conform to design laid in PCC faces over 2.10 m length complete all as specified and directed.

Supply only metallic hardener complete all as specified and directed.

M&L for 80mm thick precast coloured glazed interlocking paving blocks factory casted using grey cement with pigment, machine pressedconfirming to IS 15658 -2006 M-40 Grade and of shape haxagon/ triangular/ zigzag/ I-shaped etc. as directed. having compressive strength not less than 400 Kg/ Sqcm with the interstices complete all as specified and directed..

M & L Sand filling under floors or in foundation including watering and consolidation.

M&L for precast (factory casted) cement Concrete kerb stone casted in PCC (1:2:4) type B-1 using 20mm graded stone aggregate with plain or interlocking joints (as directed.), making groove in ground of desired dimension, placing in erect position Kerb stone in edging and set and jointed in cement mortar 1:4, making good distrubed surface of ground complete all as specified and directed. .

M&L for Maroom/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick spread, levelled and rammed including watering complete all as specified and directed. .

M&L for Concrete bed of PCC 1:3:6 type C2 using 40mm graded stone aggregate to drain pipes of 150 mm bore including packing under and hunching against the sides of pipes after they are laid and tested.complete all as specified and directed. .

M&L Reinforced concrete pipes 150mm bore, class NP2, laid and jointed complete with collars complete all as specified and directed. .

M&L for PCC (1:2:4) type BI, using 20 mm graded crushed stone aggregate as in channels of manholes etc complete all as specified and directed..

S&F 110 mm dia PVC (SWR) pipes ingle socketd, in any length with rubber ring joints fixed to walls complete all as specified and directed. .

S&F 110 mm dia PVC (SWR) vent cowl complete all as specified and directed. .

M & L for point wiring with 1.5 sqmm cable PVC unsheathed and insulated copper multistranded conductor FRLS 1100 Volts grade cable ( red colour cable to be used for live connection and black colour cable to be used for neutral connection ) controlled by one way switch drown through and including non metallic rigid PVC concealed conduit with all accessories and 1.5 sqmm copper multistrand conductor FRLS 1100 Volts grade unsheathed PVC insulated ( green colour ) continuity earth wire connected to common earth dolly and sunk cast pressed steel terminal box made out of MS sheet 1.25 mm thick for mounting of fittings like switch , socket and fan regulator with 3 mm thick hylum laminated sheet cover incl cutting Chases pinning in, for concealed conduit wiring and making goods of disturbed surface not exc 15 cm girth complete all as specified and as directed. for one light/fan/exhaust fan/bell point controlled by one switch/bell push complete all as specified and directed.

all as per item no 105 here in before but One 3 pin socket oultel 5 Amp on the same board with other switch complete all as specified and directed.

-Ditto - all as per item no 105 here in before but One 3 pin socket outlet 5 Amp independent complete all as specified and directed.

Ditto -all as per item no 105 here in before One 3 pin socket outlet 15 Amps independent with 2.5 Sqmm PVC insulated sheathed cable and 2.5Sqmm cable for earth wire complete all as specified and directed.

S&F switch piano flush type single pole one way 5 Amps complete all as specified and directed.

S&F Switch Piano flush type single pole one way 15 Amps complete all as specified and directed.

S&F Socket outlet 2 in 1, 3 pin 5 Amp flush type complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin 5Amp and 15 Amp complete all as specified and directed.

S&F Lamp holder ( batten/angle ) PVC/Polycarbonate type with back plate for batten/angle fittings complete all as specified and directed.

S&F LED lamp 7 watt complete all as specified and directed.

S&F ceiling rose, 3 terminals, PVC polycarbonate isolated body complete all as specified and directed.

S&F lamp LED heat sink white with polycarbonate diffuser, B-22 base cap, retrofit type , 220/230Volts Watt complete Make Surya/C&S/Cromption

S&F Ultra slim LED MS Batten light fittings 1X/20 Watt, power coated decrotive end cap complete with retor fit poly carbonate glass tube LED 20 Watt 4" long including suitable electric connection with three core flexible copper conductor cable of sutaible size from ceiling rose complete all as specified and directed.

S&F LED building security light fitting 25 Watt, 230Volt, AC outdoor type with high pressure die cast aluminium housing and heat resistance polycorbonate cover complete with driver, lamp and IP-65/66 protection complete all as specified and directed.

Supply and Hanging ceiling fan after cleaning OF 1200 MM SWEEP 230 Volt AC with all accessories etc complete including electric connection with three core flexible PVC insulated copper conductor multistranded white in clour 1.50sqmm cable complete all as specified and directed.

Supply and Fixing Exhaust fan steel body heavy duty 230/240 volt of size 300 mm sweep with louvers , etc complete including electric connection with three core flexible PVC insulated copper conductor multistranded white in colour 1.50sqmm cable complete all as specified and directed.

S&F in repairs sheet metal enclousers (DBS) when MCBs to be used 4 way, 240 Volt, double door single pole & neutral with 200 Amps rated bus bar complete all as specified and directed.

S&F in repairs MCB single phase and neutral up to 40 Amp 230V 10KA. B' curve type complete all as specified and directed. complete all as specified and directed.

S&F in repairs MCB SP up to 40 A, 230V. 10KA. B' curve type complete all as specified and directed.

S&F in repairs GI bracket made out from GI pipe 32mm bore 1.2mtr long fixed on wall with all including nut, bolt and GI clamps of size 25x4mm as required and including painting complete all as specified and directed.

M&L for cutting existing steel tubing and inserting suitable GI fitting etc for alteration s/addition the branch connection complete all as specified and directed.

Supply and laying bricks old size, well burnt sub class 'B' bricks as in protection cover for under ground cable laid width wise across the cable adjoining each other, laid dry complete all as specified and directed..

M&L for dry river sand cushioning for under ground cable protection with a layer of 8cm deep before laying and 15cm covering above the top ebdge of cable after laying and punning up to 18 cm depth complete all as specified and directed.. Note :- For payment purpose the punned down thickness of 18 cm only shall be considered.

M& L for Boring holes under road or cutting the road /pavement /hard standing or any other situation by mechanical or other means for inserting 25 to 40mm bore GI pipe for crossing the cable and making good both the ends complete all as specified and directed.

S&F galvanized iron pipe of 25 mm bore, Light grade with all fittings for cable protection for road crossing/ culvert/ path/ on wall/ floor/ pole or laid in floor complete all as specified and directed.

Supply, lay, joint, test and commisioning LT, XLPE insulated, screened, PVC bedded, armoured, heavy duty, electric cable with stranded aluminium conductor, 1100 Volts grade, cross sectional area 06 Sqmm, 2 core complete all as specified and directed. Note:-Excavation earthwork,sand cushioning & brick protection shall be measured & paid seperately.

M & L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6. mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metres below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts,check nuts, nuts and washers of GI or steel all as shown in electrical plate No 5 of SSR-I 2009. GI wire protected by GI pipe light grade 15mm dia connected to earth test point including excavation in any type of soil, returning filling, disposal of soil, earthing pit in PCC (1:3:6) type C1,RCC (1:2:4) type B1 precast cover slab with one handle made out of 8 mm dia round bar,20 mm dia (medium grade) watering pipe and providing layer of charcoal or coke and salt in alternative layers complete as specified or directed. & including testng on completion complete all as specified and directed.

SUBHASH CHANDRA AGARWAL

S S CONSTRUCTION CO

Mohit Enterprises

M/S Gupta Builders

Jain construction co

M/S Harshri Nath Enterprises

M/S Gupta and Company

M/s Agarwal Builders

M/S SARTHAK INFRASTRUCTURE AND ENGINEERS

RAZA ENTERPRISES

Kapoor Contractor and supplier

M/S SAJJAD HUSSAIN CONTRACTOR

SANJEEV KUMAR CONTRACTROR

sipatter singh chauhan

dm enterprises

M/S SATEESH PAL SINGH TOMAR

A K builders