Raising of plinth of existing CR bldg. by surfacing upto ground level with other allied work for approach road, yard development, water supply system AND const. of RCC boundary wall for damaged portion at 33 KV S/S DeoliKhurd.

Supplying and Filling in plinth with river sand under floors including watering ramming consolidating and dressing complete including cost of sand. (B/1.27(a))

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. :1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). (B/3.1.6)

Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in: Cement Mortar 1:6 ( 1-Cement : 6-Sand). (B/6.1.6)

Random rubble dry stone kharanja under floor (B/11.26)

Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. ('Original producers' who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786)Cold twisted deformed bars (IS:1786). (B/4.13.2)

Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation, footings, strap beam, raft, bases of columns etc. (B/4.9)

Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix / Design Mix (B/4.1)

Brick work with clay flyash F.P.S. brick (IS 13757- 1993 ) of class designation 75 in superstructure above plinth level upto floor five level in : in Cement mortar 1 : 6 (1 cement : 6 coarse sand). (B/5.15.2)

Half brick masonry in Superstructure , above plinth level upto floor V level using bricks of designation 75 Cement mortar 1 : 6 (1 cement : 6 coarse sand) (B/5.8.3)

Add extra for Square or Rectangular Pillars in superstructre flyash Brick work upto three storey : (A) Upto 45 cm length and two corners are free. (B/5.3.2)

Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc. M20 grade Nominal Mix/Design Mix (B/4.3)

Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for :Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc. (B/4.10.2)

Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcement for Walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. M20 grade Nominal Mix/Design Mix (B/4.2)

Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : Walls (any thickness) including attached pilasters, buttresses plinth and string course. (B/4.10.1)

Providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section (IS 1038-1983) joints mitred and welded with steel lugs 13x3mm, 10cm. long embedded in cement concrete block 15x10x10cm. of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with cooper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required : (A) Window side hung / ventilator top or center hung. (B/9.19.3)

Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. (B/9.26)

Providing and fixing M.S. sheet 1mm thick single leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint Add extra for double leaf shutters. (B/9.17+9.17.1)

Structural steel work in single section fixed with or without connecting plate including cutting, hoisting (height upto 10m), fixing in position and applying a priming coat of approved steel primer all complete. (B/9.1)

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. (B/1.31)

S&F in walls machine cut and polished stone shelves, tands and sills in CM 1:3 with machine cut edges :

(A) Kota stone minimum 30mm thick.: (B/6.17.3)

(B) Sand or other approved stone 50 mm thick. (B/6.17.2)

Providing & fixing precast cement concrete coping 1 : 2 : 4 mix 50mm thick complete as per specification. (B/3.8)

Making grooves as per design in plaster 10 mm to 20mm wide. (B/12.19)

Kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) For area of each slab from 2001 to 5000 Sq.Cm. (B/11.18.2)

Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete For area of each slab from 2001 to 5000 Sqcm. (B/11.19.2)

Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure 'A' 30mm thick, commercial veneer both side. (B/8.13.2.1)

Extra for providing external lipping with 2nd class teak wood battens 6 mm minimum depth on all edges of shutters (over all area of door shutter to be measured) Over item no. 8.13. (B/8.14)

Providing and laying of paver block as per IS 15658 : 2006 (Indian standard for precast concrete block for paving- specification) and IRC : SP:63-2004 (guidelines for the use of interlocking concrete block pavement) (a)M-40,80mm thick to be used in medium- traffic ( Medium traffic is defined as a daily traffic of 150-450 commercial vehicles exceeding 30 KN laden weight, or an equivalent of 0.5 to 2.0 MSA for a design life of 20 years.) like city streets, small and medium market roads, low volume roads, utility cuts on arterial roads, etc. (b)Category ‘B’ Denated only two side like I,Z,T shape etc. as per IRC SP 63:2004 (c) Add extra over item No. 11.38, A to C if reflective paver block, manufactured with wet cast vibration system in two layers is used. (d) Add extra over rates of item No. 11.38, A to C if colored paver blocks are used. (B/11.38.3(B)+11.39+11.40)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.

(A) Two or more coats on new work. (B/12.46.1)

Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cem

ent plaster on walls and pillar).Extra for using size above 200x300mm in glazed tiles and for using 400mm x 400mm MAT finished tiles in place of 300mm x 300mm size. (B/7.12+7.15)

Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4).(B/7.13)

Grading roof for water proofing treatment with water proffing compound Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). (B/10.17.1)

Supplying and fixing stone lintels/bed plates of approved quarry rough dressed in cement mortar 1:4 :Upto 15 cm. thick. (B/6.18.1)

Plaster on new surface on walls in cement sand mortar 1:6 including racking of joints etc. complete fine finished :

(A) 20mm thick. (B/12.3.2)

(B) 12mm thick. (B/12.3.3)

(C) 25mm thick. (B/12.3.1)

6 mm thick cement plaster to ceiling of mix 1:3 (1cement : 3-fine sand). (B/12.5)

Providing Gola 75mmx75mm in CC 1:2:4 (1 cement: 2 coarse sand : 4 stone aggregate 10 mm and down gauge) including finishing with CM 1:3 (1 cement: 3 coarse sand) as per standard design. (B/10.22)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding: New work (two or more coats) over and including scrapping and priming coat with cement primer. (B/12.37.1)

Painting exterior surface of Wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect including scaffolding and safety provision New Work (B/12.43.1)

(A) New Work (B/12.43.1)

(B) old work. (B/12.43.2)

Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete New Plastered Surface (three or more coats) :

Applying priming coat with ready mix pink or gray primer of approved brand and manufacture on wood work hard and soft wood. (B/12.45.1)

P&L in position CC including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work upto plinth level: 1:2:4 M15 grade nominal mix (1cement: 2coarse sand: 4graded stone aggregate 20mm nominal size). (B/3.1.2)

Repair to stone masonry in CSM 1:6 with old and new stone. (B/13.12)

Pointing on stone masonry in cement sand mortar 1:3 (1 cement : 3 sand): Raised and cut pointing. (B/12.31.2)

P&F rigid PVC pipe (IS:4985 mark) class-II/(4kg/Cm2) approved quality/ make including joining the pipe with solvent cement rubber ring and lubricant :

(A) 75 mm dia. (S/3.16.2)

(B) 110mm dia. (S/3.16.3)

P&F rigid PVC pipe fittings (IS:4985 mark) of approved quality/make including joining the pipe with solvent cement rubber ring and lubricant :

(A) Coupler (Socket).110mm dia. (S/3.17.1(ii))

(B) Plain Tee. (S/3.17.3.ii)

(C) Bend 45° (S/3.17.8.ii)

(D) Pipe Clip.110mm dia. (S/3.17.15(ii))

P&F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor: 580x440mm. (S/1.2.2)

P & F lst quality WVC Urinal (IS:2556 mark) with 25mm dia G.I. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete. Flat Back (small) size 456x355x265mm. (S/1.14.1)

P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, P.V.C Waste pipe with PVC nut 32 mm complete including cutting & making good the wall : size 550x400 mm. (S/1.36.3)

Providing and fixing 3-layer PP-R (Polypropylene random coplymer) pipes SDR 7.4 UV stabilized and antimicrobial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded Polypropylene random fittings and fixing the pipe with clamps at 1 metre spacing. This includes cost of cutting chases and making good the same including testing of joint complete as per direction of Engineer - in charge.(CONCEALED WORK INCLUDING CUTTING CHASES AND MAKING GOOD THE WALL ETC.)

(A) PN-16 Pipe, 20 mm OD. (S/2.35.2)

(B) PN-16 Pipe, 25 mm OD. (S/2.35.3)

Providing and fixing 3-layer PP-R (Polypropylene random coplymer) pipes SDR 7.4 UV stabilized and antimicrobial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded Polypropylene random fittings including trenching, refilling and testing of joint complete as per direction of Engineer - in charge. (EXTERNAL WORKS)

(A) PN-16 Pipe, 25 mm OD. (S/2.36.3)

(B) PN-16 Pipe, 32 mm OD. (S/2.36.4)

P&F bib cock (IS : 8931 mark), Superior quality of approved make :

(A) CP Brass bib cock 15mm nominal bore. (S/2.7.3)

(B) PVC heavy duty 15mm nominal bore. (S/2.7.2)

P&F Inlet connection (Angle Valves) Superior quality of approved make for wash basin, Gyser etc. CP Inlet connection 15mm brass(IS:8931 mark). (S/2.12.1)

P&F 15mm dia. Connection pipe of approved quality/make: PVC pipe with CP brass nuts upto lenth 300mm. (S/2.13.1)

P&F Full-way wall valve (IS : 778 mark) or wheel valve of approved make :

(A) Gun-metal 15mm nomimal bore. (S/2.15.1)

(B) Gun-metal 25mm nomimal bore. (S/2.15.3)

P&F PVC storage tank ISI marked (IS:12701 marked indicating the BIS license no.) of approved make with cover, 25mm dia. 1M long GI over flow pipe and 25cm long washout pipe with plug & socket, including making connection etc., complete of approved design.

(A) 500litre capacity. (S/2.26.3)

P&F SC floor trap (Nahni) of (IS:1729 mark) of approved Quality/make with socket down or hinged grating incld. Cutting and making good the floor : size 100x100 mm. (S/3.12.1)

P & F Square-mouth gully trap `A` grade (IS 651-1992 :marked) of approved make complete with C.I. grating, frame & Cover masonary chamber in C.M. 1:6, 100mm thick C.C. 1:5:10 base concrete, 40mm thick C.C.M-15 grade coping, 12mm thick cement plaster in CM 1:3 complete as per approved design & type : Trap size 150 X 100mm, ferrow cement cover with frame, Internal Chamber size 300 X 300mm. (S/3.5.1)

P&F Flush Cock/Flush Valve (IS : 9758 Mark) for WC of approved quality make : Brass/Gun metal Half-turn wt. 1 Kg. of approved quality /make, 25mm nominal bore. (S/2.14.9)

Construction of manhole in all type of soil inner size 90 X 60 Cm. 300 mm thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5:10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring, making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C. flooring, Cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead.Depth up to 0.5 M (S/3.19.1)

Construction of soakage well in all type of soil with 300 mm thick dry masonry, top and bottom 300 mm course in CM 1:6, 80mm thick stone slab, jointing of slab in CM 1 : 3, Ralthal, Kharanja, 40 mm thick M-15 grade C.C flooring , earthwork complete as per approved drawing including disposal of earth within a lead of 50 mtr.: Size 240 Cm. dia outside & 240 Cm. depth. (S/3.22.3)

Construction of septic Tank in all types of soil with 40 Cm .thick masonry in CM 1:6, 15 Cm thick C.C bed of 1:5:10, M-15 grade C.C floor & RCC slab covering with M15 grade c.c. floor, 50 mm thick ston

Providing & Laying C.C. 1:3:6 (Stone Agreegate 20mm nominal size) all around PVC Pipe including 7.5 cm thick bed concerte [Width & Height = Dia of Pipe in CM+15CM] excluding cost of Pipe & Excavation of trenches etc.: PVC pipe 160 mm dia. (S/3.16.5.2)

P&F rigid PVC pipe fittings (IS:4985 mark) of approved quality/make including joining the pipe with solvent cement rubber ring and lubricant: Vent Cowel. 110mm dia. (S/3.17.12(ii))

Wiring of light point/fan point/exhaust fan point/call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS (IS:9537 P-III) virgin material PVC conduit & it's ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose/Holder/3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/Wiring accessories refer Chapter E-04, E-05 & E-07 For additional technical parameters of product/work refer Annexure 'A' attached with this BSR.

(A) Short point .(upto 3 mtr.) (E/1.1.1)

(B) Medium point (upo 6 mtr.) (E/1.1.2)

(C) Long point. (upto 10 mtr.) (E/1.1.3)

Supply and installation of high tensile low carbon steel rod molecularly bonded with 99.9 % Copper thickness (250 microns) and confirming to UL 467, IS/IEC 62561-2 of following size and length and as per point mentioned (a), (b), [c), (d), (e) below :- (a) Bore a hole of dia. 100 mm of required length, Place the rod in the centre of Hole, (b) filled with anti corrosive conductive compounds with the permanent sealings at both the ends, CPRI/ERDA tested with RMS capacity of minimum 30 KA for withstanding 1 second. To ensure the moisture content and electrical conductivity, 25 kg for 2000mm & 50 Kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. The compound shall be tested form NABL acredeated lab for low resistivity (less than 0.12 Ohm-meter) & high conductivity in nature with carbon as a major content as per referance of IS 3043-1987, IEEE 80-2013 (clause 14.5d), IEEE 837 & IER 1956 with latest amendemnts (c) Connect the rod with copper Strip/ Conductor/ Wire with suitable clamp made from tinned copper and SS 304 Bolt, (d) Place Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. (e) Testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book. (e) Test certificates for confirming above standards from OEM is mandatory. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR. (B) 25 mm thick and 3 Mtr. Long. (E/14.4.2)

Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS (IS:9537 P-III) PVC conduit & it's ISI marked (IS:3419-1988)accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal, 10 A modular switch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E-04, E-05 & E-07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR-ON Board. (E/1.3.1)

Supplying and fixing of power plug point with Modular accessories as per PWD specification for electrical Works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost of ISI marked modular 16 amp. Switch (IS :3854) and 6/16 amp. socket outlet (IS:1293) making connection, testing, etc. as required. For specification of Wiring accessories refer Chapter E-07 related item & For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. (E/7.37)

Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR

(B) 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. (E/4.1.14)

S&F following sizes (dia.) of ISI marked virgin material MMS (IS:9537 P-III) PVC conduit along with ISI marked (IS:3419-1988) accessories as required in recess including cutting the wall, covering conduit and making good the same as required. For additional technical parameters of product/work refer Annexure 'A' attached with this BSR 20mm. (E/1.4.1)

Providing & Fixing of BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan Conforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR. 1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5). (E/15.7.3)

Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminium housing

with in built driver, System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10%, P. F.≥0.95, CRI >80, life time of minimum 50000 Burning Hours with, 70% of intial Lumen maintaned till life ends, CCT 3000°K/4000°K/5700°K/6000°K/ 6500°K (As per ANSI Bin), Maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate (T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate/Report from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/work, refer Annexure "A" attached with this BSR. 1170mm(+/-10%) LED batten with min. lumen output 2200 lm (E/17.1.1)

Providing & Fixing of IK08, IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminum material with heat dissipation fins on housing with UV stabilized PC (UV stablization report submitted for UV cover)/Toughened Glass cover and secondary lens on each LED & should be SMD type of 3 to 5 watt each. The System efficacy >=125 lm/wt and potted driver & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety, Power Factor >0.95 driver Efficiency>85%, THD(I) <10% Humidity 10% to 90% RH Working Temp -5C to 45C. Driver current<750mA. The luminaire shall be BIS certified and Trade mark certified. Life Expectancy Equal or more than 50000 burning hrs with Minimum 70% lumen maintened, CRI >70 and CCT 5700K +355K. Surge protection shall be min ≥ 4 KV internal and min 10 KV external inside driver compartment driver should be Phase to phase protection of 440 V for 4 Hrs. Manufactures Word Mark/Name Engraved/ Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/ LM80) Certificate/ report with liable warranty of product/ accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR.

(A) LED Street Light fixture with Minimum lumen output 11225 lm. (E/18.12.6)

(B) LED Street Light fixture with Minimum lumen output 2450 lm. (E/18.12.1)

Providing & Fixing of Recessed/surface mounting heavy duty Enclosure made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3. powder painted complete with din rail making internal DB terminations with copper lugs, detachable gland plate, including making connections, testing etc. as required.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. Suitable for Six / Eight module for MCB/ RCCB (E/6.9.2)

Providing & Fixing of 240/415 V isolator ISI marked IS:13947-III/conforming to IEC 60947-3, suitable for AC22A utilization category, 4KV impulse withstand voltage, true contact indication, Red colour dolly / lever shall have single mould covering over all poles for operation, two position din rail mounting, minimum phase termination capacity of 35sq.mm. IP 20 contact protection and fitted in existing distribution board / sheet including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR Double Pole Isolator 63A rating. (E/6.2.1.2))

Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm., conductor line load reversibility, IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR Single pole MCB (With B/C curve tripping characteristics) 6A to 32A rating (E/6.1.1.2)

P & F 1.2mm thick M.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR (E/15.10)

Providing & Fixing of modular type 120 W Step Fan regulator duly ISI marked (IS 11037:1984 ) with CM/L no. printed made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , including all as per pre approved by Engineer in charge, making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. 5 step fan regulator 2 Module 360 dgree rotating. (E/7.29.1)

Providing & Laying P.V.C./XLPE insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to IS:155

4 P-I/IS : 7098 P-I of 1.1 KV with H4-Grade electrolytic aluminium conductor confirming to IS 8130 of purity>99.6 %, round/flat strip armouring of cables, Inner/outer sheath confirming to IS:5831 in existing RCC/Hume/Stoneware/PVC pipe/Open duct/cable trench/ Cable tray (with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810. For additional technical parameters of product/work refer Annexure 'A' attached with this BSR. (A) 4.0 Sq. mm 2 core. (E/11.2.1.1)

BoQ_Ver3.0

Painting, lettering, figuring and border on both side of Existing Sign board (Sheet size 1200x900mm) with ready mix synthetic enameled paint of superior quality in required shade and colour etc complete in all respect. All section of fremed post and steel tubes will be painted with primer and two coats of enamel paint as per specification & Direction of Enginner in Charge.

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

PART - A Earth work in excavation by mechanical means (Hydraulic Excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils. (B/1.8)

Supply, stacking and spreading of graded crusher brocken hard stane aggregate fee from organic matter including stacking & spreading in yard/trenches as per the standard specification of size 40mm to 63 mm including all lead & lift, transportation, labour, loading, unloading & T&P required for graveling work as per direction if Engineer incharge incl.dressing & leveling.

Earthwork in filling of excavated earth except back cotton Soil With watering, and Compaction of Spreaded earth in 15-30 cm layers, levelled and neatly dressed as Per requirement of site and direction of engineer in charge, work includes cost of earth with taxes, loading, unloading, transporation,labour, water and T&P etc. Complete with all lead and lift.

P&F steel almirah shutters for almirahs & wardropes in different sizes as per site requirement made with 20 Gauge CNC sheet & having three way locking devices with six brass lever double lock and godrej type handle 10mm dia locking rods, painted with three coats of superior quality danedar synthetic enmeled paint over approved quality primer coat etc. complete in all respect including fixing at site with help of suitable holdfast or nuts & bolts etc. (measurement shall made for front visible position / size of shutter including frames.

Supply, stacking, spreading & hand ramming of quarry rubbish in layer not exceeding 15 cm (loose) incl. all lead & lift, transportation, loading,unloading with water & hand ranning with labour incl. T&P, machinery, water etc. complete in all respect finishing in lying, level and camber as per direction of Engineer in charges.

Demolishing of existing GSS building situated at JPD premises in deolikhurd power house with care & safety to avoid any damage to surrounding. The job also includes cost of all T&P, labour, machines required for job and dismantling of all items like parapet, roof (RCC/stone patti), walls, lintels, chajjas, doors, chokhats, windows, floor, DPC, sanitary system, plinth, masonary etc. upto ground level with desposal of serviceable & unserveable material received from demolishing upto suitable dumping ground or suitable premises of agency as no recovery will be done for serviceable material complete for all lead & lift as per direction of engineer incharge. The rate for this job should be quoted/analysed by considering no recovery will be made for all serviceable materials which received from demolishing of said building.