PURCHASE OF GENERATOR FOR AC TO COMMUNITY HALL

Amount

Supply and installing

Suppil & installation of 100KVA Diesel Generator set including required contactars/ control devices,protection such as suitable MCCB and earth fault relay using CT inneutral earthing conductor, and accoustic enclosure as per CPCB norms and as per technical details given below on suitable size cc foundation.<br>1. engine .<br>a)make of engine -Volvo Eicher/MTU/Cummins.<br>b.type of Engine -Diesel engine .<br>c. NO. Of cylinders -as per manufactures standards.<br>d. Method of cooling -water cooled with radiator <br>e.Aspiration -turbo charged after cooled<br>f.Design suitable for generating set operation.<br>g.Out put -required HPas per manufacturers standards at 1500 rpm under NTP condition .<br>2. standard accessories with diesei engine <br>a. Flay wheel to suit flexible coupling <br>b .Close coupling .<br>c. Air cleaner <br>d.Radiatior with fan provided with fan guard <br>c. water temperature gauge <br>d .RPM indicator with hour meter .<br>e. Battery charging ammeter <br>f. fuel indicator <br>4. safety controls for engine <br>a. trip for low lubricating oil pressur .<br.b. trip for high water temperature . <br>c. Alarm for low fuel level <br>6.Brushlees afternator <br>a. make -stamford/crompton/LS<br>b. Type - self exited and self regulated .<br>c. capacity -100 KVA/80 KW @ 0.8 PF <BR>D . System of voltage - 3 phase, 415 V, 4 wire system <br>e. speed - 1500 rpm.<br>f. Voitage regulation band -+/-5% of rated voltage <br>g. frequency : 50 Hz<br>h . insulation - class f / H<br> The alternator shouid confirm to IS 4722 ANDwarranteed for 3 years. operation and service manual , spares and tools shall be provided .<br>8 fuel tank <br> suitable size buiit in type integrated with the acoustic with full tank Diesel <br> fuel connection shall be done as per standards <br>9. battery <br> suitable capacity fully charged with leads and terminals of appropriate AH capacity as per manufactures requirement .<br>10.supplying and providing automatic battery charger suitable for the 100 KVA DG set <br>11.Tools kit<br> standared manual control system <br> including all necessary accessories and meters <br> Accoustic enclosure: As per CPCB norms <br> The DG set should have warranty of 3 years from the date of installation .<br> cummins (Model 6BTAA5.9G13 Ccummins,)

Supply and provding following size M.S. pipe - 5mm complete with suitable size 12mm flange coupling with minimum 4/5mtr using allied packing with MS bolt with washer and rising the same on the wall/ parapet using chain pullies , scaffoldings, supports with M.S angle /channels etc. including painting the pipe with one coat of zinchromate primer over a coat of high temperature rasistance alu .paint etc .fo extending the exhaust pipe of the newly errected D.G .set .100 mm dia or nearest size B class MS pipe

14.1 Excavation for foundation in soft soil including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 metres. [Delete]

14.8 Providing and laying in position cement concrete 1 :3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc. including form work etc. as required

fees for getting sanction from Electrical inspectrate including all lasion work etc (actuals will be paid on production of relevant documents.)<br>

Copying charges for additional copies per A3 sheet

Charges for preperation of electrical schematic per A3sheet <br>

90.12.7.32 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 120 sq mm

90.12.1.32 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil).3.5 core 120 sq mm

90.12.7.41 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 16 sq mm with factory made clamp [Delete]

90.12.7.42 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 25 sq mm with factory made clamp

90.12.7.29 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 50 sq mm with factory made clamp

9.1.33 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

9.1.34 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 25 sq. mm (28mm)

9.1.22 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 50 sq. mm (35mm)

9.1.25 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 120 sq. mm (45mm)

Supply and provding earth clamps made out of copper strips of 20 x1.2 mm for earth glands of size 120 sq mm to 185sq mm including cutting and bending the falt exactiy to the shape of the gland drilling necessary holes for nut & bolt , tinning the point of contacts and giving connection to the main earthing as requried .<br>

providing and fixing G.I.tape 25 mm x 3 mm thick on tary or suface of wall complete as required (For horizontal run )

Supplying and installation including all manner of supports/suspenders, anchor bolts etc cable trays made out of suitable size channel sections , slotted angle ,flats, MS plates etc as required including painting with 2 coats of synthetic enamel paint over a coast of zinc chromate primer , making good the damages colour washing etc as required .<br>

Earthing with G.I. earth plate 600 mm x 600 mm x 6 mm thick including accessories , and <br> providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2 metre long etc . With charcoal / coke as required.

providing and fixing testing jointb made of 2 no .strips as mentioned below of the following sizes provided on either side of the conductors with 4 nos of GI bolts , nuts check nuts and spring washers etc . Compiete as required (for down conductors) <br>2 nos 25 x 3mm copper strip 150 mm long

Supply and claping the following size of strips on surface of wall /parapet / existing cable tray using clamps fabricated from 20 x 3 mm GI flat duly painted or heavy duty GI spacer saddles . Spacing of clamps not exceeding 1m, making good the damage . colour washing etc as required (for horizontal run)<br>25 x3 mm copper strip tinned at the points of contacts

supply and laying the following size of strips laid 0.60 m below ground level including excavating trench of suitable size and refilling etc as required (in ordinary soil)<br>25 x 3 mm copper strip tinned at the points of contacts

5.19 Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 3.15 mm dia copper wire on surface or in recess for loop earthing along with existing surface / recessed conduit/ submain wiring / cable as required.

90.11.1.15 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required6 way (8+18) - double cover TPN vertical DB with provision for fixing 4P MCB / Isolator/ RCCB/ RCBO as incomer and SP/ TP MCB as outgoing (IP 42/43)

2.10.4 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

2.13.2 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

90.14.1.2 Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623. Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments will be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc.Supply and fabrication of MV panel board using 1.6mm CRCA sheet, powder coated (excluding base frame)

90.14.2.2 Supply and providing 3mm SMC sheet as shrouding for bus interconnection / terminations etc. including required nut & bolt etc.

90.14.3.3 Supply and providing heavy duty 'A' section neoprene gasket in the panel boardSupply and providing 'U' section PVC beeding in the panel board

90.14.5 Supply and fabrication conveyance and installation of angle iron frame work for wall mounting panel board

90.14.6 Supply and providing copper bus bars including finger type SMC bus bar supports in the bus chamber, suitable size nut & bolt, providng heat shrink sleeves etc. as required

90.14.7 Supply and providing copper earth bus in the panel board

supply and installing multi function meter VAF+PF accuracy class 1

supply and providing 150/5Ametering ct accuracy i

supply and providing 160A 25/35 KA 3MCCB with thermal magnetic release 80-100% setting on the exsisting enclousure and giving connection

supplying and fixing LED indicators for all voltage ranges- blue colour

carring out control wiring for pnel -2.50 sq mm single run with required sockets.<br>

painting letters or figures of the following size with enamel paint as identification mark to SB, DB, panel board etc as required <br>2.50 cm ,4 cm or 5 cm height

90.14.11.13 MCCB AccessoriesSupply and fixing rotary handle, External type (including BUC handle with door interlock ) in the existing MCCB of rating up to 250 A

90.14.10.4 Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.16 A-100A, 25/35 kA (Ics=100%Icu), 4 pole, current limiting type MCCB having thermal setting range of 80 - 100% with thermal magnetic release having adjustable OL

2.1.5 Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required.160 Amp TP&N

supply and providing 6 kg Dry chemical powder type fire extinguisher with hose and clamps including fixing it to wall as required

supply and providing 2 mm thick synthetic PVC FIRE retardent insulating matmat to withstand 3.3 KV dielectic strenth conforming to IS .<br>

POWERLINE CONSULTANTS

Bidder Name

POWERLINE CONSULTANTS

KERALA STATE INDUSTRIAL ENTERPRISES LIMITED