PROVN OF FUEL INJECTION EQUIPTMENT ROOM AT 260 FD WKSP COY EME AT PANGODE MIL STN TRIVANDRUM UNDER GE (ARMY) TRIVANDRUM

Amount

Material and Labour for Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mtr in depth for fdn and steps and getting out in hard/dense soil complete all as specified and directed.

Excavating in trenches not exceeding 1.5 meter wide and not exceeding 1.5 meter in depth for foundation for erection of poles, stays, laying cables, stays etc and getting out in hard/dense soil and in road cutting all as specified and as directed

Material and labour for removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

Returning filling in including spreading, leveling, watering well ramming in layers not exc 25cm thick using excavated soil complete all as specified and directed.

Material and labour for Plain cement concrete 1:4:8 Type D-2, using 40 mm graded stone aggregate as in foundation complete all as specified and directed.

Material and labour for Pre Cast Cement concrete block masonry type C1, 1:3:6 (Using 20 mm grated aggregate ) with solid block exc 10 cm in width and setting in CM (1:6) complete all as specified and directed.

Material and labour for Moorum red bajri filling in floors or pavings, laid in layers n exc 15 cm thick, spread levelled and rammed including watering complete all as specified and directed.

Material and labour for Hardcore guage exc 63 mm n.exc. 100 mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and rolled / rammed to a true surface.(Broken stone or Boulders) complete all as specified and directed.

Material and labour for cement concrete 1:4:8 Type D-2 ( using 40 mm graded stone aggregate) , 75mm thick as in sub base complete all as specified and directed.

Material and labour for 75 mm thick PCC 1:3:6 type C2, using 40 mm graded stone aggregate as in plinth protection/path finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for Mild steel bars 10mm TMT bar dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for coloumns, hooking ends and binding with and including mild steel wire not less than 0.9mm dia or securing with clips quality conforming to TMT bars complete all as specified and directed.

All as per item No 10 above but 5mm dia and over upto including 10mm dia stirup spacers and binders

Material and labour for Mild steel bars 8mm dia , cut to length, bent to shape required, including cranking, bending spirally for hooping for coloumns, hooking ends and binding with and including mild steel wire not less than 0.9mm dia or securing with clips quality conforming to TMT bars complete all as specified and directed.

Material and labour for PCC 1:2:4 type B1 (20mm graded aggregate) as in DPC, copings and similar work mixed with water proofing compound including necessary form work etc complete all as specified and directed. (Note : Water Proof Compound shall be paid seperately)

Material and labour for RCC 1:2:4 type B1 (20mm graded aggregate) as in shelves, chajjas and similar works etc complete all as specified and directed.

Material and labour for RCC 1:2:4 type B1 (20mm graded aggregate) nominal mix as in foundation, including rafts footing , plinth beams, base for columns etc complete all as specified and directed.

Material and labour for RCC 1:2:4 type B1 (20mm graded aggregate) nominal mix as in columns, pillars, etc complete all as specified and directed.

Material and labour for RCC 1:2:4 type B1 (20mm graded aggregate) nominal mix as in lintel beam and similar work etc complete all as specified and directed.

Material and labour for Form work to sides of concrete foundations, footings, bases of columns, raft, and raft beaams sides and soffits of foundation and plinth beams and similar work flat fair finished surfaces etc complete all as specified and directed.

Material and labour for Form work to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

Material and labour for Form work to sides and soffit of floor or roof beams, ,beam haunching, lintel, beam, shelves including supports overhangs etc complete all as specified and directed.

Material and labour for applying two coat of acrylic emulsion paint over one coat wall primer incl preparation of new plaster wall surface complete all as specified and directed.

Material and labour for applying two coats of oil bound distemper over one coat wall primer over 1mm thick wall putty on preparation of undecorated surfaces on walls complete all as specified and directed.

Material and labour for applying three coats of white wash on preparation of undecorated surfaces on ceiling complete all as specified

Material and labour for double layer for 5mm thick rendering in cement mortar 1:4 mixed with water proofing compound over 10mm thick rendering in CM 1:6 on fair faces of concrete surfaces finished fair and smooth without using extra cement for external walls complete all as specified and directed. (Note : Water Proof Compound shall be paid seperately)

Material and labour for 10mm thick rendering in cement mortar 1:6 on fair faces of concrete surfaces finished fair and smooth without using extra cement for internal walls complete all as specified and directed.

Material and labour for 5mm thick rendering in cement mortar 1:3 on fair faces of concrete surfaces finished fair and smooth without using extra cement in ceiling complete all as specified and directed.

Material and labour for Cement concrete of Type C1 1:3:6 (20mm graded aggregates) in cills incliding weathering, slightly rouded or chamfered angles and throating complete all as specified and directed.

Material and labour for 25 mm thick, plain cement concrete, M-15 (Nominal Mix), type B-0 (using 12.5 mm graded crushed stone aggregates) as in floors finished rough surface to receive floor finishes, complete all as specified and directed by Engr-in-charge.

Material and labour for 15 mm thick screed bed in cm 1:6 for laying floor finishes complete all as specified and directed.

Material and labour for 10 mm thick rendering in CM (1:3) as in backing coat complete all as specified and directed.

Material and labour for 10mm thick vitrified ceramic tiles dark shade (square/ rectangulat) polished, area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engr-in-charge.

All as per item No 31 above but as in skirting/dado of wall etc complete all as specified and directed by Engr-in-charge.

Material and labour for Form work to soffits of suspended slabs such as roof slabs, and similar work not exc 200mm thick ( horizontal or sloping) in rough finshed surface of concrete complete all as specified and directed by Engr-in-charge.

Material and labour for Form work to edges of concrete flats, trads, breaks in floors, window cills , concrete railing opening in concrete wall floor and roof n exc 20 cm wide and sides of RCC/PCC bends in wall, horizontal or sloping and similar work exc 10 cm but exc 20 cm wide in rough finshed surface of concrete complete all as specified and directed by Engr-in-charge.

Material and labour for RCC 1:1.5:3 Nominal mix concrete 20mm graded aggregate as in roof slab and similar work complete all as specified and directed by Engr-in-charge.

Material and labour for Rendering 10mm thick on concrete surfaces in CM (1:3) finished even & smooth without using extra cement complete all as specified and directed.(Note : Water Proof Compound shall be paid seperately)

Material and labour for Plain cement concrete 50mm thick M-15 (Nominal Mix), type B-0,1:2:4 (using 12.5mm graded aggregates) as in roof kerbs, mud stops, roof padding etc using water proofing compound, complete all as specified and directed. Note : Water proofing compound shall be paid separately.

Supply only Intergrated water proofing compound complete all as specified and directed.

Material and labour for Brushing neat cement slurry with 3.0 Kg of cement per sq. meter complete all as specified and directed.

Material and labour for preparation of surface by removing dirt, dust and applying bituminous primer @ 1.20 kg/sqm providing 3mm thick APP modified water proofing membrane pre fabricated fine layer and weighing not less than 3.00 Kg/sqm reinforced with non wove fabric weighing not less than 150grms/sqm having softening point not less than 150 degree centigrade, having tensile strength of 650 N/sqcm & 350 N/Sqcm in longitudinal & transverce directions respectively of the reinfocement tensile strength, 10 cmm side over lap and 15 cm end lap complete all as specified .

Material and labour for preparation of new untreated surfaces apply two coats aluminimum paint over one coat aluminium primer on APP water proofing membrane complete all as specified and directed by Engr-in-charge.

Material and labour for Harrison rails, mild steel, chromium plated with fixing brackets, stops rollers standard quality etc complete all as specified by Engr-in-charge.

Material and labour for Aluminum door/windows using power coated aluminum section, including necessary joining cleats,glazing clips, rubber neoprene packing, handles aluminum snap beading screws etc powder coating of any colour (thickness of powder coating minimum 50 micron ) complete all as specified and directed.

Supply and fix 18/19mm thick prelaminated particle board, exterior grade prelaminated both sides with decorative choice laminations fixed with bedding ,screws to timber/aluminium frame work complete all as specified and directed.

Material and labour for Sheet glass ordinary quality and glazing with rubber neoprene packing in square n exc 0.5 sqm in each pane 3 mm thick glass all as specified and directed by engineer in charge.

Material and labour for Sheet glass ordinary quality and glazing with rubber neoprene packing in square exc 0.5 sqm in each pane 5.5 mm thick glass all as specified and directed by engineer in charge.

Supply and fix Aluminium alloy, anodised, sliding door bolt 300mm long with hasp , staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed.

Supply and fix for aluminium Deco grill 10mm thick,with 80mm spacing and joints spacing 20x4mm fixed with aluminium bedding powder coated as in standard shape and size complete all as specified and directed by Engr-in-chagre.

Supply and fix Aluminium alloy wire clth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed.

Material and labour for double action floor spring hydroulically regulated made up of minimum 1.25mm sheet aluminium box, main body with stainless steel cover, governing pivot made of brass other parts made of mild steel heavy duty and fixed complete all as specified and directed by Engr-in-charge.

Material and labour for Door closer hydralulically regulated designation No 3 universal type, suitable for door shutters of 851 to 1000 mm width and weight between 61 to 80 Kg and fixed using aluminium extruded section all as specifieed by Engr-in-charge.

Supply and fix Aluminum anodised, barrel tower bolts of extruded section and fixed of 200mm long complete all as specified and directed.

Supply and fix Aluminum anodised, barrel tower bolts of extruded section and fixed of 100mm long complete all as specified and directed.

Supply and fix Extruded aluminium alloy handles 100mm long, fabricated type, anodised complete all as specified and directed.

Supply and fix 75 mm long Butt hinges, extruded aluminum alloy with galvanised mild steel hinge pin, anodised type B-21 complete all as specified and directed.

Supply and fix Extruded aluminium alloy handles, fabricated type, anodised,150mm long complete all as specified and directed.

Supply and fix Brass Mortice lock of 4 Levers, vertical type, of size 100mm. complete all as specified and directed.

Material and labour for plain cement concrete, 1:2:4 type B-1, (using 20mm graded crushed stone aggregates) as in surface channels and drains, complete all as specified and directed by Engr-in-charge.

Material and labour for Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc, complete all as specified and directed by Engr-in-charge.

Supply and fix floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor (Overall length of cover plate 150mm) complete all as specified and directed.

Point wiring complete for One light point controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade with multi stranded, copper conductor in and including non-metalic PVC conduit totally concealed in wall with recessed, pressed steel terminal boxes of suitable size concealed etc, incl 3mm thick laminated sheet cover for housing switches, socket outlets, fan regulators etc, including provn of 1.5 sqmm nominal cross sectional area, PVC insulated, FRLS, unsheathed, 1100 volt grade, multistranded single core green colour copper conductor for earth continuity connected to earth dolly complete all as specified and directed NOTE: Pressed steel terminal boxes should be one of synthetic enamel paint over a coat of red oxide and concealed in wall with suitable 3mm thick laminated sheet cover plate for mounting switch/sockets etc., shall be deemed to be included in the quoted rate Make: Havells / Plaza/Anchor/Finolex/Nicco/Polycab/RPG

All as per ser item No. 61 above but for One fan point controlled by one way switch and regulator

All as per ser item No. 61 above but for one 5 Amps socket outlet on independent board.

All as per ser item No. 61 here in above but point wiring with 2.5 Sqmm FRLS cable and 2.5 sqmm cable earth continuity wire for one 3 pin socket outlet,15 Amps on independent board.

All as per ser item No. 61 here in above but point wiring with 4.0 Sqmm FRLS cable and 4.0 sqmm cable earth continuity wire for one 3 pin socket outlet,15 Amps on independent board.

S&F switch piano, flush type, single pole, one way 5 Amp, 240 volt, white or ivory ISI marked complete all as specified

M&L for stepped type electronic fan regulator, 60 Watts, flush type 240 Volts, 50 Hz, suitable for ceiling fan 1200 mm/1400 mm sweep all as directed

S&F switch socket combination 2 in 1, 5 pin, 6 Amps flush type 240 volts, white or ivory ISI marked complete all as specified Make: Anchor or equivalent make of Havells/Legrand/Cona/Crabtree

S&F switch socket combination 2 in 1, 6/16 Amps flush type, universal, 240 volts, white or ivory ISI marked complete all as specified Make: Anchor or equivalent make of Havells/Legrand/Cona/Crabtree

S&F ceiling rose surface PVC/Polycarbonate, isolated body with face Bakelite 65 x 50 mm three terminal complete all as specified

Supply, fixing, connecting and testing MCB triple pole 40 to 63 Amps, 240 volt, 10 KA all as specified and directed Make: Indo Asian/L&T/Legrand/Havells

Supply, fixing, connecting and testing MCB single pole 5 to 32 Amps, 240 volt, 10 KA all as specified and directed Make: Indo Asian/L&T/Legrand/Havells

S&F sheet steel metal enclosure single pole & neutral with a 2 pin and earth plug and socket complete with one single pole MCB SP 20 Amp, 240 volts complete all as specified and directed. Make: Legrand or equivalent make of L&T/Indo Asian/Havells

Supply and fixing sub main wiring with 2 runs of 4.0 sqmm single core, multi-stranded PVC insulated, FRLS unsheathed cable 1100 Volts grade with copper conductor drawn through and including concealed non metalic PVC conduit, medium grade, ISI marked, 20/25mm bore with conduit fittings and accessories concealed in wall/ceiling/floor including 1 runs run of 4.0 Sqmm multistranded PVC insulated FRLS, copper conductor cable as earth continuity conductor and connecting to common earth dolly complete. NOTE: Two runs of 4.0 sqmm copper cable and one run of 4.0 sq mm copper cable alongwith non metallic PVC conduit/conduit accessories will be measured as one unit length Make: Havells / Plaza/Anchor/Finolex/Nicco/Polycab/RPG

Supply only ceiling fan 1200mm sweep with down rod, 240 Volts, white colour, ISI marked BEE 5 star with latest BLDC technology complete including all technical accessories complete all as specified and directed Make: Havells / Bajaj/Orient/Crompton/Khaitan

S&F surface/wall mounted LED batten for T8 lamps, extruded aluminium body with PC diffuser & inbulid driver for and including 1 x 20 watt linear ultra bright LED T8 tubular lamp 1200mm, 865-CRI 80, 6500K etc including prewired and making electrical connection from connector to light fittings & connecting up complete all as specified and directed. Make: Cat No. DMLN1LT8-16 & LTT8-20 of Crompton or equivalent make of Bajaj/Philips/Havells/Wipro

Supply and fixing wall mounted LED bulkhead light with polycarbonate diffuser including 1 x 12 watt warm white LED, oval type with IP-65 protection complete all as specified and directed. Make: Luker or equivalent make of Bajaj/Philips/Crompton/Havells/Wipro

S&F Freedom Neo pressure die-cast, roadway luminaries, epoxy black powder coated sheet aluminium housing, with epoxy white powder coated CRCA sheet steel gear tray, clear acrylic cover as diffuser with IP65 protection and accessories, including supply and fixing LED security light 1x45 watt 6000K, high efficacy-110LM/W, with fixing bracket made of 40mm bore galvanised iron light grade pipe made to shape having overall length not exceeding 1.5 mtr, fixed on the wall with suitable No. mild steel clamp of 25mm width and four Nos nuts,bolts & washers of 12mm dia, 100mm long complete including connecting wire with flexible PVC insulated copper cables from ceiling rose to fitting complete and testing, including taking down existing unserviceable one and removing from site complete all as specified and directed. Make: Crompton or equivalent make of Havells/Philips/Bajaj/Wipro

Supply and lay in trenches burnt clay bricks, sub class (Designation 75) 'B' of old size for cable protection over the cables complete all as specified and as directed

M&L for sand filling around the cable with approved quality clean dry river sand unwashed for sand cushioning of Under ground cable including spreading, levelling, watering & punning down to desired thickness complete all as specified and directed Note: Punned thickness only will be considered or payment

Taking down existing serviceable LT UG XLPE cable of size 3.5 core 35sqmm from the proposed site and relaying the cables at site complete as directed by the Engr-in-Charge NOTE: Excavation, earthwork, sand cushioning, brick protection & cable protection etc. will be measured and paid separately under relevant items of this schedule.

Supply & laying in trenches/drawn through pipes or in road crossing/paths/drains/ducts/floors/along poles/equipments etc., of XLPE insulated, armoured with multistranded aluminium conductor cable conforming to IS-7098 Part-I (1998), heavy duty (LT UG cable) conforming to IS-1554, 1100 Volts grade of size 25 sqmm 4 core nominal cross sectional area including connecting up using suitable size aluminium lugs testing and commissioning complete all as specified and directed NOTE: Excavation, earthwork, sand cushioning, brick protection & cable protection etc. will be measured and paid separately under relevant items of this schedule.

Supply and fixing double compression copper gland for fixing armoured cables of size 25 sqmm 4 core to 35 sqmm nominal cross sectional area complete all as directed

Supply & laying GI steel tubing light grade 40mm dia for protection of cable on poles, under road crossing etc, complete all as directed. Make: Jindal or equvalent make

M&L for distribution board, vertical, made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, VTPN 4 way, 415 volts grade with insulated rated bus bar assembly with isolated neutral bar,door earthing, earth bar IP- 43 protection, mechanical impact strength IK-08, flush to wall, including testing suitable for fixing MCCB, MCB TPN, SPN, SP etc, complete all as specified and directed Make: Legrand or equivalent in L&T/Havells/Indo Asian/ABB

Supply and fixing MCCB triple pole and neutral (four pole) 63 Amp, 415 volts, 50 Hz, having thermal setting range 70% to 100% and adjustable magnetic setting and breaking capacity 25 KA including making incoming and outgoing connections complete all as specified and directed. Make: Legrand or equivalent in L&T/Havells/Indo Asian/ABB

M&L for in replacement of fabricate, supply, install, test & commission cubical pattern CPRI approved LT feeder Panel box of Size 1000mm x 750mm x 500mm, Outdoor type, medium channel 75mm floor mounted (mounted on pedestal) totally enclosed factory made dust and weather/vermin proof (protection class IP-65) double door front opening with locking arrangement made of frame MS angle iron frame work of size 40mm x 40mm x 6 mm and CRCA sheet of 3.15 mm thick as per IS-5039 duly painted with two coats of synthetic enamelled paint of approved colour over a coat of red oxide primer outside & inside complete, suitable for 415 Volts, 50Hz, 3 phase 4 wire system of aluminium bus bar - 4 Nos. of two sets each with epoxy insulated coating duly colour coding and insulated support of length 0.80 mtr of 400 Amps current carrying capacity for three phase and neutral by providing PVC sleeves and carry out internal wiring of PVC insulated multi stranded copper conductor cables not less than 2.5 sqmm with suitable size PVC copper thimbles/lugs, nut, bolts & washers, gaskets etc., and providing cable glands at cable entry into panel, making all electrical connection of incoming and outgoing complete with the following accessories and mounting panel board on ground with PCC (1:3:6) bedding upto a height of 30cm above ground level complete all as directed:- (a) Aluminium busbar of 400A rating for 3 phase & neutral - 02 Sets. (b) Provn of fixing arrangements of On load change over switch - 02 Nos. (c) Internal wiring with PVC insulated copper conductor multistandard appropriate guage including all copper lugs and connection incoming /outgoing cable with lugs and cable glands.

M&L for Earthing complete in replacement with galvanised iron mild steel earth plate electrode 60 cm x 60 cm x 6.3mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth of not less than 1.5 metre below normal ground level, connected to glavanised earth lead of GI strip of size 32mm x 6mm by means of GI Bolts, Nuts, check nuts and washers of the earth and thimbles and other end of the earth strip connected to earthing test point and protected by galvanised iron pipe light grade 40mm dia from earth plate to Panel and DG set and water pipe 20mm dia GI medium grade raised upto a level of 50cm above ground level with plug at top, earthing pit in PCC (1:3:6) type C-1 RCC pre-cast (1:2:4 type B-1) cover slab of 50 mm thick using 8.00mm dia CTD bars reinforcement both ways at 140 mm centre to centre with two handles, 20 mm dia GI pipe medium grade for watering pipe, wire mesh, funnel and providing charcoal or coke and salt in alternative layers of 15 cm including necessary earth work in soft/loose soil, returning, refilling and removing of surplus soil to a distance not of MES Schedule Part-I of SSR-2009 exceeding 50 mtr testing complete all as shown in electrical plate No-3 complete all as specified and directed.

All as per ser item No. 91 above but of GI wire of size 4mm dia.

Supply, installation, testing and commissioning of 5 (five) star rated inverter type Split type Air Conditioner of capacity 1.5 TR (copper type), refrigerant R410-A, comprising of indoor and outdoor units with copper coil single phase, 230Volt, 50Hz AC with cordless remote control with high EER rated BLDC compressor, including necessary fixing arrangement complete as relevant IS (indoor unit at suitable place and height inside the room and outdoor unit at suitable place outside the room on plinth height/ on wall or roof as suitable and as directed) including metallic bracket with fixing bolts for outdoor unit, insulated copper piping as required length etc., complete all as specified and as directed by Engr-in-Charge Make: Voltas or equivalent make of Blue star/Hittachi/LG

Supply and fix air cooled split unit air conditioner electric driven, single phase of capacity of 2 TR, BEE 5 star rated complete all as specified Make: Voltas or equivalent make of Blue star/Hittachi/LG

Supply and install voltage stabilizer for automatic operation with digital voltmeter to monitor in/out voltage with time delay and bypass switch, single phase, thermal overload protection, low & high voltage cut-off protection, LED indication, IC controlled, naturally air cooled indoor type and design for input variation between 170 volts to 250 volts with output output voltage stabilized at 230V with accuracy of + 2.5% and of capacity 4 KVA complete all as specified and directed Make: V-Guard Model No. VWR 400 or equivalent Microtek/Brenfort

AKASH CONSTRUCTIONS

KENZ CONSTRUCTIONS

Lucky Enterprises

JEETH CONSTRUCTION