STBR/SOPD-G/ Katigorah-04/12 i) Balance work Estimate for RCC Bridge at Choligram over river Larang with approaches and protection works ii) Construction of Road starting from NH-06 near MVI gate at Digharkhal to Gita Mandir iii) Construction of R

Amount

i) Balance work Estimate for RCC Bridge at Choligram over river Larang with approaches and protection works. Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 (A) With Crushed Stone (IV) RCC Grade M 25 (ii) For height above 5 m upto 10 m

Furnishing and placing reinforced/Prestressed cement concrete in superstructure as per drawing and Technical Specifications at clause 800,1205 A. with crushed Stone I. Using concrete mixture R.C.C M-30 Grade b.Height 5.0 to 10.0m

Supplying, fitting and placing TMT IS:1786 (Fe 500) bar reinforcement in sub-structure complete as per drawing and technical specifications. TMT-IS 1786 ( Fe-500 D) Primary Producer (TATA/ SAIL/ Esser Steel/ Jindal panther steel/ Shyam steel or equivalent)

Reinforcement in Super Structure: Supplying, fitting and placing TMT conforming to IS:1786 Fe 500 D reinforcement in super-structure including splicing complete as per drawing and technical specifications. TMT-IS 1786 ( Fe-500 D) Primary Producer (TATA/ SAIL/ Esser Steel/ Jindal panther steel/ Shyam steel or equivalent

Supplying, fitting and fixing in position true to line and level elastomeric bearing conforming to IRC : 83 (Pt. II) Section IX and clause 2005 of MORT & H Specifications complete including all accessories as per drawing and Technical Specifications as per MORTH section 1000,2000,2200

Providing and laying cement concrete wearing coat M-30 grade including reinforcement complete as per drawing and Technical Specifications

Drainage spouts complete as per approved drawings and technical specifications.

Construction of pre-cast RCC railing of grade M30 Grade in situ with 20mm nominal size aggregate, true to line and grade, tolerance of vertical RCC post not to exceed 1 in 500 centre to centre spacing between vertical post not to exceed 2000mm levelling adequate space between vertical post of expansion, complete as per drawings and technical specifications.

Providing and laying strip seal expansion joint catering to maximum horizontal movement up to 70mm, complete as per approved drawings and standard specifications to be installed by the manufacturer/ supplier or their authorised represantative ensuring compliance to the manufacturar's instructions for installation.

Back filling behind Abutment,Wing wall and Return Wall complete as per drawing and technical specification clause 1204.3.8 B.sandy Material

Providing and laying filter material underneath pitching in slopes as per drawing and technical specifications 1302

Providing and laying pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing and technical specifications 1302 A. Stone/Boulder

Providing and laying of boulder apron laid in wire crates made with 4 mm dia GI wire conforming to IS : 280 & IS : 4836 IN 100 mm x 100 mm mesh (Weaved diagonally) including 10 per cent extra for laps and joints laid with stone boulders weighing not less than 40 kg each .

Construction of Embankment with Material Obtained from Borrow Pits Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compactingto meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 (i) Private Land

Construction of subgrade and earthen shoulders with approved materials obtained from borrow pits with lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.1 & 300.2 (Qty as per earthwork statement)

Granular sub-base with well Graded Material (Table 400.1)(A) By Mix in Place Method.Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density,complete as per Technical specification Clause 401.(ii) For Grading II material.

Water Bound Macadam Sub-base/Base-III.Providing, laying, spreading and compacting stone aggrates of specific sizes to water bound macdam specification including spreading in uniform thickness, hand packing, rolling with vibratory rollers 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/binding materials to fillup the interstices of coarse aggregates, watering and compacting to the required density.A. By manual means (Qty as per Annexure)

Providing and laying interlocking concrete block pavement (M40) having thickness 80mm as per technical specification clause 1504 complete including carriage.

Excavation for Structures : Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. (I) rdinary soil, Upto 3 m depth ,

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 (B) With natural Gravel (I) P.C.C Grade M 10 Nominal mix 1:3:6

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 (B) With natural Gravel (III) P.C.C Grade M 20 Nominal mix 1:2:4

Providing weepholes in brick masonry /stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the tructures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7

ii)Construction of Road starting from NH-06 near MVI Gate at Digharkhal to Gita Mandir Clearing and Grubbing Road Land . Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable materials to beused or auctioned up to lead of 1000metres including removal and disposal of top organic soil not exceeding 150mm thickness.(i) By Manual Means,(A) In area of non thorny jungle

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 (I) Private Land

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1 (I) Private Land

Construction of granular sub-base by providing well graded material, spreading in uniform layers by tracktor with grading attachment on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. (ii) For grading II materials

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smoth wheel roller 80-100 KN in stages to proper grade and camber, applying and brooming, stone screening to fill up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405. (A) By manual means. 3) Grading No. 3 : Using stone Screening Type-B 11.2mm for Gr-III.

Providing and laying interlocking concrete block pavement(M40) having thickness 80mm as per technical specification clause 1504 complete including carriage (a) including Edge block / Edge restraint.

Painting two coats including prime coat with epoxy paint of approved brand on concrete/steel surfaces after through cleaning of surface to give an even shade as per drawing and Technical Specification Clause 1701

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 1.5 mm thick supported on GI pipe 50 mm dia firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 1701 (ii) 600 mm equilateral tringle

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 1.5 mm thick supported on GI pipe 50 mm dia firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 1701 (iv) 800 mmx600 mm rectongular

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. 200m stone(precast)

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. (I) Ordinary Soil , upto 3 m depth

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 B With natural Gravel I P.C.C Grade M 10 Nominal mix 1:3:6

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 B. With Natural Gravel(ii) P.C.C.Grade M 20

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. 600 mm dia

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. (I) Ordinary Soil , upto 3 m depth

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203. (B)With natural Gravel (I) P.C.C Grade M 10 Nominal mix 1:3:6

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204. (B)With natural Gravel (I) P.C.C Grade M 15 Nominal mix 1:2.5:5

Supplying, fitting and placing TMT(Fe-500 D) reinforcement bar (Other ISI approved TMT reinforcement bar ( SAI/BISCON/THERMAX OR equivalent) in substructure complete as per drawings and technical specification Clauses 1002,1005,1010 & 1202

iii) Construction of Box Cell Culvert with approach road over Rokhitto Nallah at Leverputa Part-1 (Batterchak) Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201. (i) By Manual Means (a) In area of non thorny jungle

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 (i) Private Land

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1 (I) Private Land

Construction of granular sub-base by providing well graded material, spreading in uniform layers by tracktor with grading attachment on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. (ii) For grading II materials

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smoth wheel roller 80-100 KN in stages to proper grade and camber, applying and brooming, stone screening to fill up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405. (A) By manual means. 3) Grading No. 3 : Using stone Screening Type-B 11.2mm for Gr-III.

Providing and laying interlocking concrete block pavement(M40) having thickness 80mm as per technical specification clause 1504 complete including carriage (a) including Edge block / Edge restraint.

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801 600mm equilateral triangle

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801 600mm circular

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801 800mm x 600mm rectangular

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Construction of C.C Drain: Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. I. In Ordinary soil (i) Upto 3 m depth

Providing Providing concrete for plain/ reinforced concrete in open foundation complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203. A With crushed Stone ( II). PCC Grade M15 Nominal mix 1:2.5:5.

Providing plain/reinforced concrete in Sub Structure complete as per drawings and technical specifications Clause 802, 804,805,806,807, 1202 & 1204. A. With crushed Stone III P.C.C Grade M20 Nominal mix (1:2:4)

sachin sahoo (BID ID -282155)