8443 deposit work Supply, Application, and Installation of Thermoplastic Paint Road Markings and Raised Pavement Markers (Cat-Eyes) at Helipad Exhibition Ground, Sector-17, Gandhinagar

NO. In Figures (RS.)

Road marking with hot applied thermoplastic paints with reflectorising glass

beads on bitumin surface providing and laying a hot applied thermoplastic

compound 2.5 mm thick including reflectorising glass beads @ 250gms per sqm

area, thickness of 2.5mm is excluding of surface applied glass beds as per

IRC:35-2015. The finished surface to be level, uniform and free from streaks and

holes. zebra patta /bump patta lane/center line/ edge line/cut patta. The white

color marking should provide liminance coefficinet on cemend road shalll be min

130 mcd/m2/lux and Asphalt road shall be min 100 mcd/m2/lux during the

Cat Eye / Road Stud / RPM: Supplying of Molded Twin Shanks Raised Pavement

Markers made of polycarbonate and ABS moulded body and reflective panels

with micro prismatic lens capable of providing total internal reflection of the light

entering the lens face and shall support a load of 13635 kgs. tested in

accordance to ASTM D 4280 Type H and complying to Specifications of Category

A of MORTH Circular No RW/NH/33023/10-97 DO III Dt 11.06. 1997. The

height, width and length shall not exceed 20 mm, 130 mm and 130 mm and with

minimum reflective area of 13 Sqcm on each side and the slope to the base shall

2 be 35 +/- 5 degree. The strength of detachment of the integrated cylindrical 1650.00 No 326.23

shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/-

mm) from the body is to be a minimum value of 500 Kgf. Fixing will be by drilling

holes on the road for the shanks to go inside, without nails and using epoxy

resin based adhesive as per manufacturers recommendation and The color of the

marker should be as per the IRC 35-2015 and as directed by Engineerin-charge.

Supplying of solar road stud (Solar k tie) construction aluminium alloy steel

dc water proof design conform to IP67 Dimension 140 mm x 128mm x 82mm +

1mm height of shank + 54mm +0.5 mm diameter of shank 42.5 mm + 0.5 mm

plastic unbreakable, scratch, resistant poly carbonate for maintenance free

operation solar panel high efficiency monocrystalline 3v/50 mAh Battery

XTSRS.01. XTSRS.02. Super capacitor 2.7 v/22 of Six super bright LED with

18000 mod view distance up to 800 meters flash rate 1H2 according to

3 customers requirement resist compression can take the load of 25 tons vehicle 700.00 No 1692.76

color red and yellow working time 80 to 100 hours continuously after the battery

is fully charged and complete fixing will be drilling holes on the road for the

shank to go inside with out nails and using epoxy resin based adhesive per

manufactures recommendation and complete as directed by the Engineer.

I/We am/are willing to carry out the work at…………………. % above/below percent (Should be written in figures and words) of the

estimated rate mentioned above. Amount of my /our tender works out as under.

Estimated amount put to tender-3462476.50 Estimated amount put to tender-3462476.50

Deduct………% below Add………% Above

In words In words

The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge for which

no extra payment shall be made.

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3 Income tax TDS will be deducted at a source while making payments of bills

In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017 Cement

Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is a change as per actual mix design

the cost of difference of cement consumption have been deducted from the rate of original item at the rate of input rate mentioned

in all the tender.

Deputy Executive Engineer Executive Engineer

Capital Project Sub Division 3 Capital Project Division No

Gandhinagar Gandhinagar