SEOP 25/2021-22

Amount

Excavation in foundation, trenches etc. in earth work, lift upto 1.50 meter stacking the excavated soil not more than 3 m. clear from the edge of excavation and then returning the soil in 15 cm layers, when required into plinths sides of foundations etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed within all leads and lifts. All kind of soils i/c hard & soft rocks.

Providing and laying cement concrete 1:4:8 (1 cement:4 sand:8 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth within all leads and lifts.

Boulder filling / stone soling dry hand packed under floors as directed by Engineer-in-Charge in all leds and lifts.

Providing and laying cement concrete 1:6:12 (1 cement:6 sand :12 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of centring and shuttering in foundation and plinth up to all leads and lifts.

First class brick work using common burnt clay building bricks in cement mortar 1 : 6 ( 1 cement : 6 Sand ) up to all leads and lifts in:-

Foundation and plinth.

Super-structure above plinth level upto floor two level.

Half brick masonry in common burnt clay first class building bricks in Cement mortar 1 : 4 ( 1 cement : 4 Sand ), in superstructure above plinth level up to floor two level.

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5 mm so as to give a fair finish including centering ,shuttering, strutting and propping etc with wooden battens and ballies, height of propping and centering below supporting floor to ceiling not exceeding 4 metres and removal of the same for in-situ- reinforced concrete and plain concrete work in

Foundations, footings, bases of columns etc. and mass concrete.

Columns , pillars , post and struts, Squares, rectangular and polygonal in plan.

Circular or curved in plan.

Beams, cantilevers, girders and lintels, Sides and soffits of beams, beam haunchings, cantilever girders, bressumers and lintels not exceeding 1 metre in depth.

Flats surfaces such as soffits and suspended floors, roofs landing and the like, floors etc. upto 200 mm in thickness.

Edges of slabs and breaks in floors and walls under 20 cm wide

Providing and laying cement concrete 1 : 1.5 : 3 (1 cement : 1.5 sand : 3 graded stone aggregate 20 mm nominal size ) and curing complete excluding cost of form work & reinforcement for reinforced concrete work in foundation, footings, bases of columns and the like and mass concrete upto all leads and lifts in:

Foundation, footings, bases of columns and the like and mass concrete.

Suspended floor roofs, landing and shelves and their support, balconies, beams, girders, bressumers & cantilever upto floor two level.

Providing and laying cement concrete 1 : 1.5 : 3 (1 cement : 1.5 sand : 3 graded stone aggregate 20 mm nominal size ) and curing complete excluding cost of form work and reinforcement for reinforced concrete work upto all leads and lifts in:

Providing and laying cement concrete 1 : 1.5 : 3 (1 cement : 1.5 sand : 3 graded stone aggregate 20 mm nominal size ) and curing complete excluding cost of form work and reinforcement for reinforced concrete work upto all leads and lifts in columns, pillars, posts and struts.

Providing Tor steel reinforcement for R.C.C work including bending, binding and placing in position complete upto floor two level.

Providing 40x 3 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30X10x15 cm 1:3:6 (1 cement:3 sand: 6 graded stone aggregate 20 mm nominal size).

Providing and fixing powder coated / anodised aluminium work for door, window, ventilators and partitions with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868. (Minimum anodic coating of grade AC 15) fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/Neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically where ever required including cleast angle, aluminium, snap beading for glazing/panelling C.P. brass/stainless steel screws. All complete as per architectural drawings and the directions of Engineer-in-Charge. (Powder coating brown or White coloured)

For doors, windows and ventilators and glazed partitions frames

For shutters of doors, windows and ventilators including providing and fixing hinges/pivots and making provisions for fixing of fittings wherever required including the cost of PVC/Neoprene gasket as required (fittings and glazing/panelling shall be paid for separately)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/Neoprens gasket etc. complete as per the architectural drawings and the directions of Engineer-in-Charge. (Cost of aluminium snap beading shall be paid in basic item).

Glazing with glass panes of 4 mm thickness (weight not less than 10.00 kg/sqm)

Glazing with glass panes of 5.50mm thickness (weight not less than 13.75 kg/ sqm.

Providing and fixing board partitions with Prelaminated board BWP phenol bonded exterior/ interior grade both sides 12 mm thick.

Providing and fixing fly proof galvanised M.S. wire gauge of I.S. gauge designation 85 G with wire of dia 0.56 mm to windows and clerestory windows

Providing and fixing aluminium anodised powder coated grill of required pattern to existing window / ventilator with 80 mm panels, holes with 25 x 8 mm thick aluminium flat including fixing with aluminium screws and bolts and nuts complete in alluminium channels base frames (Aluminium channels Base frame work to be measured & paid for separately)

Providing and fixing 250 x 16 mm anodized aluminium sliding door bolt anodized transparent or dyed to required colour and shade with stainless steel bolts, nuts & screws etc complete.

Providing and fixing aluminium tower bolts (barrel type) anodized transparent or dyed to required shade and colour with stainless steel screws etc complete.

Providing and fixing aluminium handles anodized transparent or dyed to required colour or shade with necessary stainless steel screws etc. complete.

Providing and fixing 100 mm bright finished brass floor door stopper with rubber cushion screws etc to suit shutter thickness with stainless steel screws etc complete.

Providing and fixing bright finished hard drawn hooks and eyes 150 mm with stainless steel screws etc complete.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete in all respects.

Cement concrete flooring 1:2:4 (1 cement : 2 sand:4 graded stone aggregate 20 mm nominal size)laid in one layer finished with a floating coat of neat Cement. 40 mm thick.

Providing and laying Duro stone vetrified tiles 600 x 600mm of approved design, shade and make (Kajaria / Nitco / RAK / AGL make) in flooring, treads of steps and landing laid over a bed of 12mm thick cement mortar 1:3 (1cement : 3 sand) and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete.

Providing and laying Duro stone vetrified tiles 300 x 300 x 10 mm of approved design, shade and make (Kajaria / Nitco / RAK / AGL make) in skirting, risers of steps and dados on 12 mm thick cement mortar 1 : 3 ( 1 Cement : 3 Sand ) laid over and jointed with neat cement slury and finished with flush pointing in white cement mixed with pigment to match the shade of tiles as required complete.

Providing and fixing on wall face PVC (D-Plast or equvalent) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete 100 mm dia pipe.

Providing and fixing on wall face PVC (D-Plast or equivalent) accessories for rain water pipes including filling the joints with approved adhesive complete PVC plain bend 100 mm dia

Steel work welded in built up sections trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of red lead paint In trusses and trussed purlins in buildings.

Providing and fixing 0.60 mm thick prepainted steel sheet (TATA / Jindal or equivalent make) in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesories as required as per the direction of Engineer-in-charge.

Providing and fixing ridges or hips 60 cm overall with 0.60mm thick prepainted steel sheets (TATA / Jindal or equivalent make) in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charges.

Providing and fixing M.S. BP Sheet 1.66mm to 2mm thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely)

Providing and fixing 0.35mm thick prepainted sheet (TATA / Jindal or equivalent make) in roof ceiling with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster 5 microns primer coating icluding fixing with prepainted iron J or L hooks, bolts and nuts 6mm diametre with prepainted limpet and rubber washers complete with all accesories as required as per the direction of Engineer-In-Charge.

6 mm Cement Plaster to ceiling in cement mortar 1 : 3 (1 cement : 3 sand) in all heights, leads and lifts complete.

15mm Cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. Cement Mortar 1:6 (1Cement:6 Sand).

15 mm Cement Plaster in single coat on fair side of brick/concrete/stone walls for exterior plastering including arrises, internal rounded angels, chamfers and/or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1 : 4 (1 cement : 4 sand)

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete.

Distempering two coat with oil bound washable distemper of approved brand and manufacture (Nerolac / Asian / Berger / Shalimar or equivalent) and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth priming coat with distemper primer.

Applying one coat of distemper primer of approved brand and manufacture on wall surfaces after thoroughly brushing the surface free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Finishing wall with water proofing cement paint of approved brand and manufacture (Snocem, Birla White or equivalent) and of required shade on undecorated wall surfaces(two coats)to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials.

Painting two coats (excluding priming coat) on new steel and other metal surfaces with ready mixed enamel paint of approved brand (Nerolac / Asian / Berger / Shalimar or equivalent) and shade, brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter.

Painting two coats (including a priming coat) on new wood and wood based surfaces under coat with enamel paint of approved brand (Nerolac / Asian / Berger / Shalimar or equivalent) and shade, finishing coat with flat oil paint brushing to give an even shade including cleaning the surface of dirt, dust and other foreign matter sand papering and stopping.

Providing under layer for plinth protection of 75 mm thick (unconsolidated ) bed dry brick/stone aggregate 40 mm nominal size will rammed and consolidated and grouted with fine sand including preparation of ground.

Providing plinth protection 50 mm thick in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 graded stone aggregate 20 mm nominal size)

Dismantling doors, windows and clerestory windows, ventilators etc. (wood or steel) shutters including chowkhats, architraves, hold fasts and other attachements etc. complete and stacking them within 20 metres lead. Not exceeding 3 sq.m in area.

Demolition above G.L. upto floor two level including disposal of unserviceable materials within 20 metres lead and including cutting the necessary reinforcement and separating out from R.C.C. /R.B. works:- R.C.C. work.

Constructing course rubble hammer dressed "U" shape open surface drain with side wall 15 X 22 cm in cement mortar 1 : 6 (1 cement : 6 sand) and inside plastering with cement plaster 1 : 3 (1 cement : 3 sand) including earth work and laying 10 cm cement concrete in 1 : 5 : 10 (1 cement : 5 sand : 10 graded stone aggregate of 40 mm nominal size) and 7.5 cm cement concrete 1 : 2 : 4 (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design.

Providing and fixing vitreous china wash down water closet (European type) W.C pan of approved make (Hindware / Cera / Jal or equvalent) including CP Brass Jet with integral 'P' or 'S' trap including cutting and making good the walls and floors wherever required complete in all respects.

Providing and fixing PVC automatic flushing cistern of approved make (Hindware / Cera / Jal or equvalent) with a pair of PVC / C.I. or mild steel brackets, complete with fitting including PVC syphonic apparatus, mosquito proof lid, PVC union and coupling for connections with inlet, outlet and over flow pipes including cutting holes and making good the same (overflow pipe to be measured and paid for separately) 10 liters net capacity.

Providing and fixing vitreous China wash basin 550 x 400 mm (Hindware / Cera / Jal or equvalent) with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same complete in all respects.

Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and C. P. waste with C. I. or M. S. brackets painted white including cutting holes and making good the same but excluding fitting 470 x 420 mm with bowl depth 178 mm (Hindware / Cera / Jal or equvalent)

Providing and fixing plastic seat (Solid/Hollow type) and cover for wash down water closet with C.P. brass hinges and rubber buffers Solid type Coloured plastic seat and cover (Hindware / Cera / Jal or equvalent)

Providing and fixing 32mm (thirty two millimeters) nominal diameters C.P. brass waste of approved make (Hindware/CERA) for wash basin or sink including brass check nut complete.

Providing and fixing 32 mm dia, PVC waste pipe flexible (coil type) length not less than 800 mm.

Providing and fixing PTMT Hi quality duel hanging bath room mirror of 4 mm thick glass of approved quality and colour with steel screws and rawl plugs etc complete :- size 600 x 450 mm

Providing and fixing C.P. brass towell rail complete with C.P. brass brackets fixed to wooden plugs with C.P. brass screws. 600 x 20 mm

Providing and fixing C.P. brass soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws.

Providing and fixing C.P. Brass bib tap with Capstan head 15 mm dia (Cera or Hindware make)

Providing and fixing C.P. Brass pillar tap with Capstan head 15 mm dia(Cera or Hindware make)

Providing and fixing C.P. stop cocks 15 mm dia(Cera or Hindware make)

Providing and fixing white glazed fire clay stall urinal with automatic C.I. flushing cistern (of approved make) with fittings M.S. or C.I. brackets standard size C.P. brass flush pipe and spreaders with unions and clamps (all in C.P. brass) C.I. trap with outlet grating and other coupling in C.P. brass including painting of cistern and fittings cutting and making good the walls floors where required (Cera or Hindware make)

(a) Single stall urinal with 5 litres C.I. automatic flushing cistern.

Providing and fixing PVC connection pipe with brass unions 300/450 mm length 15 mm nominal bore

Providing and fixing brass full way valve with wheel

(a) 15 mm nominal bore

(b) 25 mm nominal bore

Providing and fixing G.I./M.I. union of following sizes (where not included in the items) 15 mm nominal bore

Providing and fixing PVC floor trap ISI marked of self cleaning design including cost of cutting and making good the walls and floors etc. complete 110 x 75 mm (Diplast or Vectus make)

Providing and fixing to wall ceiling and floor galvanised mild steel tubes (heavy grade) tube fittings and clamps including making good the wall, ceiling and floor. (TATA or Jindal make)

(i) 15 mm nominal bore

(ii) 25 mm nominal bore

Providing and fixing high pressure PVC spigot and socket waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete (Diplast or Vectus make)

(a) 90 mm dia

(b) 75 mm dia

Providing and fixing PVC Collar, ISI marked including fixing with approved adhesive etc. complete(Diplast or Vectus make)

(a) 90 mm dia

(b) 75 mm dia

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete 110 mm(Diplast or Vectus make)

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawl plugs etc. complete.

(a) 90 mm dia

(b) 75 mm dia

Providing and fixing 100 mm dia chromium plated grating of superior quality for floor, gully or nahani trap

Constructing brick masonry chamber for under ground C.I. inspection chamber and bends with common burnt clay building bricks in cement mortar 1 : 5 (1 Cement : 5 Sand) C.I. cover and frame (light duty) 355 x 610 mm internal dimensionsr, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) RCC top slab with 1 : 2 : 4 mix (1 Cement : 2 Sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1 : 5 : 10 mix (1 Cement : 5 Sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 15 mm thick with cement mortar 1 : 3 (1 Cement : 3 Sand), finished with a floating coat of neat cement on walls and bed concrete etc. complete Inside dimensions 455 x 610 x 450 mm deep single pipe line

Providing and fixing PVC water storage tank of ISI : 12701 marked, G. I. inlet and outlet connection, 15 mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level (Vectus or Diplast make)

1000 liters net capacity tank

AGR Engineers