CWE BLY/GE(W)/38 OF 24-25 SPECIAL REPAIR TO BLDG NO T-188 AND PROVN OF PLUMBING ITEMS BLDG NO P-197 TO P-200 JCO LIVING ACCN AND P-216/C,P-195 AND P-196 (NCO STUDENT LIVING) OF JLA UNDER GE (WEST) BAREILLY

Amount

Taking down cement plaster includinguding racking out joints, hacking for key & scrubbing down with water etc. complete all as specified and directed.

Dismantling, floor, hearth or wall tiling includinguding cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of Concrete (unreinforced) is ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar includinguding all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

M&L for cement concrete type D2,1:4:8 (using 40 mm graded stone aggregate) as in mass concrete complete all as specified and directed

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) removing from site complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) removing from site complete all as specified and directed.

Dismantling timber scantlings 40 Sqcm and over in section , in any position ,framed work complete all as specified and directed.

Dismantling asbestos cement/CGI/PGI (corrugated, semi corrugated etc) sheets in roof coverings complete all as specified and directed.

S & F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates inluding one coat of zinc chromate primer before fabrication distance pieces, cleats etc GDE Fe 410-S. complete all as specified and directed.

S & F Pre-painted galvalume aluminium zinc coating GI based semi corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M & L for 1mm thick one side decorative laminates other side prelamination Mica/Sunmica to plave over wooden work with fevical ST 998 synthetic rubber adhesive includinguding preparation of old or new wood surfacecomplete all as specified and directed. (Note - Colour/Pattern to be approved by GE.

Providing and fixing tiled false ceiling for insulation and accoustic purpose at auditorium halls or similar buidling of approval materials of 8 to 12mm thick Micro-tegular edge pre-painted with acrylic emulsion white colored calcium silicate false ceiling tilels of size 595mmx595mm having density 790-850kg/m3 water resistant, Non combustible, Termite resistant and thermal conductivity 0.15w/m OKC in approved design (calsi Micro Square/calsi Sand textured with pin hole) to be laid over grid frame work, suspended on 15mm black groove inter locking metal grid of hot dipped galvanized steel sections consisting of main “T” runner with suitably spaced joints to get required length and of size 15 x 38 mm made form 1.5 mm thick (Minium) sheet, spaced at 600mm long spaced between “T” at 600mm centre to center or form a grid 600 x 600mm sheet to be interlocked at middle of the 600 x600mm panel/grid and laying false ceiling tiles of approved texture in the grid includinguding, required cutting/making, opening for services like diffusers, grills, light fittings fixture, smoke detectors etc Main “T” runners to be suspended from ceiling using GI slotted cleats of size 30x5 mm flat iron to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanized butterfly level clips of size 85x30x0.8mm spaced at 600 centre to centre along T. The bottom of all T-sections having exposed width of 15mm shall be prepainted with polyster paint and a black groove running in length at centre includinguding dismantling of existing false ceiling. The specification shall be complete for all heights as per specifications, drawings and as directed.

M&L for non skid ceramic coloured tiles Edge cut 7 to 8 mm thick (Square) size of each tiles 400 x 400 mm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screeding 15mm thick in CM 1:6, complete all as specified and directed.

M&L for glazed coloured ceramic tiles 450 x 300 mm x 7 mm thick in vertical wall complete or in patches surfaces set and jointed in neat cement slurry and pointed in white cement using pigment to match the shade of tiles over and including plastering 10mm thick in CM 1:4 including dismantling of extsting tile complete all as specified and directed.

M & L for 75mm thick PCC 1:3:6 , type C-2 using 40 mm graded stone aggregate as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. Exposed surfaces finished even and smooth without using extra cement includinguding raking out joints between panel to panel and panel to wall and plugging complete all as specified and directed .

M&L Brick work with fly ash bricks (old size) as per IS 12894 -2002 straight or curved on plan exc 6 m mean radius built in cement mortar 1:6, complete all as specified and directed.

M&L rendering 15 mm thick in CM 1:6 on brick masonary wall surfaces on fair faces of brick masonry finished even and smooth witout using extra cement complete all as specified and directed.

M&L 15mm thick rendering in cement mortar 1:4 to on brick masonary wall surfaces on other than fair faces of brick masonary fair finished without using extra cement with using water proofing liquid compound as per manucturer's complete all as specified and directed. (Note -water proofing shall be measured and paid seprately)

Supply Liquid water proofing compound conforming to IS specification

M&L Pressed steel frames size of size 105mm x 60mm (using 1.25 mm thick PBI sheet) for doors with one or more rebates includinguding necessary fixing lugs, hinges, lock strike plate, etc., with and including filling of PCC 1:3:6 type C0 ( using 12.50 mm graded stone aggregate) complete all as specified and directed.

S&F for 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed .

S & F 150 mm thick Aluminium, anodised, barrel tower bolts of extruded section and fixed

S&F 150mm size aluminium handles, cast type anodised completed all as specified and directed.

S&F 300 mm long aluminium sliding door bolts plate type with bright bolt not less than 16 mm dia with and includinguding a minimum of 6 bolts and nuts, 04 Nos on bolt plate and 02 Nos on staple plate and fix complete all as specified and directed

S & F in replacement fancy type 125mm size brass CP shower rose all as specified.

S&F in replacement 15 mm dia bib tap fancy type chromium plated with flange quarter turn complete all as specified as directed.

S&F in replacement brass chromium plated tubular towel rail 20 mm dia 60 cm long complete all as specified.

S&F in replacement 15mm bore PVC connections, with PTMT nuts of length 450mm complete all as specified and directed.

S&F in replacement fancy type brass chromium plated soap dish of 160x160x90 mm , complete all as specified.

S&F in replacement fancy type chromium plated brass angle/stop valve type suitable for 15mm bore pipe complete all as specified.

S&F in replacement vitreous china squatting pan of orrissa pattern long pan size 580 x 440 mm white with "P"or "S" trap size 110 mm dia front or back inlet and integral foot rest any pattern (excluding flushing cistern and flush pipe) including provn of lime concrete bedding complete all as specified and directed.

S&F in replacement PVC low level cistern 10 litres capacity, valve less, symphonic action type with float, handle includinguding 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed

S&F PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fitting includinguding of taking down of old pipe complete all as specified and directed by Engr-in-charge.

S&F PVC (SWR) 110mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fitting including taking down old PVC pipe complete all as specified and directed.

S&F PVC (SWR) 110mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75mm bore bends any radius complete all as specified and directed.

Taking up or down15 mm steel tubing and connections includinguding cleaning for refixing or removal complete all as specified and directed.

Taking up or down 20 mm steel tubing and connections includinguding cleaning for refixing or removal complete all as specified and directed.

M&L preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and includinguding one coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for preparation of new untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and includinguding one coat of pink primer complete all as specified and directed.

M&L two coats of exterior weateher emulsion paint on new plastered wall surfaces over a coat of primer of any description includinguding preparation of surfaces, complete all as specified

M&L for two coats OBD on newly plastered wall surface with airless electric sprayers over a coat of primer applied using airless electric sprayers over one coat of plaster of paris putty of 1 mm thickness complete all specified and directed (Note :- Application to be done through authoried apllicator manufacturer)

M&L two coats of exterior weateher emulsion paint on old plastered wall surfaces of any description includinguding preparation of surfaces, complete all as specified and directed.

M&L for complete removal of exiting treatment on wall by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate girt to make surface clean, free from dust, loose paint etc by skilled labour and applying two coats of OBD on wall with airless electric over a coat of primer applied using airless electric sprayer over one coat of plaster of paris 1mm thickness complete all as specified and directed (Note :- Application to be done through authoried apllicator manufacturer)

Dismantling of roof terracing cement / brick concrete (un-reinforced) and existing water proofing treatment of any thickness in any position and of any portion from top of roof of building, cleaning surface of roof with wire brush / mechanical brush and with water thoroughly to remove all dust / dirt and loose particles to expose base concrete roof slab and removal of rubbish / demolished material out of MD land complete all as specified and directed.

M&L PCC 1:2:4 type B-0 (using 12.50 mm stone aggregate) as in, levelling course with to be finished even and fair without using extra cement on roof surface / chajja (thickness of concrete will be provided as per site requirement and as directed by engr-in-charge) roof kerbs, coping, benching etc includinguding weathering slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for 15 mm thick bedding layer on surfaces in CM 1:4 with water proofing compound @ 200ml per 50 Kg of cement complete all as specified and directed.(Note:- WPC shall be measured and paid separatly)

Supply and providing water proofing treatment with polymeric standard water proofing membrane 3 mm thick having 10 years guarantee for water tightness all as specified and directed and described as under : (a) Prepartion of RCC roof surface and applying one coat of polymeric modified bitumen 85/25 @ 1.2 Kg/Sqm over a coat of polymeric primer @ 0.30 Kg/Sqm includinguding cleaning surface, all as per manufacture's specification complete all as specified and directed. (b) Supply & Providing APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced/ torch application of membrane with 10 cm overlaps as required thereof, complete all as specified and directed. Make :- IWL Hyperplas Polyster (M/S IWL), Super Thermolay (M/S STP Limited), Torch Shield AP by Pidilite Industries.

M & L for applying one coats of Bitumen based UV reflective and water proofing paint with aluminium finish over APP membrane and maximum coverage 8.00 Sqm per litre per coat on non assessible roof over APP membrance complete all as specified and directed.

S&F in replacement Vitreous china wash down water closet single piece (Cascade pattern) with seamless flushing cistern square design duroplast slim seat cover, slow falling seat cover size 69x37x73CM / 66x35x71 complete, including connection to drain pipe etc complete all as specified and directed.

M&L for 40mm thick cement concrete type B1, 1:2:4 (using 20 mm graded stone aggregate) as in floors, finished even and smooth with out using extra cement complete all as specified and directed

M&L for glazed coloured ceramic tiles 300 x 200mm x 7mm thick in vertical wall complete or in patches surfaces set and jointed in neat cement slurry and pointed in white cement using pigment to match the shade of tiles over and including plastering 10mm thick in CM 1:4, includinguding dismantling floor, hearth or wall tiling/terrazo includinguding cement mortar bedding complete or in patches and removing rubbish off the premises including dismantling of floor or wall tiles including cement morter complete all as specified and directed.

M&L for non skid ceramic coloured tiles Edge cut 7 to 8 mm thick (Square) size of each tiles 300 x 300 mm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screeding 15mm thick in CM 1:6 complete all as specified and directed.

M&L 5 mm thick cement plaster on fair faces of concrete as in ceiling using CM 1:4 finished even and smooth without using extra cement and then applying three coat of white wash after preparing the surface including taking down cement plaster on brick wall/stone wall, ceilings etc, racking out joints, hacking for key & scrubbing with water completely

M&L for preparation of old distempered surface of walls includinguding plugging nail holes with cement based putty,making good surface to match existing surface and applying two coats of oil bound distemper complete all as specified and directed

M&L for preparing of old distempered surface of ceiling and applying one coat of oil bound distemper complete all as specified and directed

M&L preparation of New plaster surfaces and applying Two coat of cement base paint on walls over a coat of primer complete all as specified and directed

S&F 15mm bore tubes medium grade galvanised iron with and including fitting and fixed to walls and ceiling or laid in floors complete all as specified and directed.

S&F 20 mm bore tubes medium grade galvanised iron with and fitting and fixed to walls and ceiling or laid in floors including complete all as specified and directed.

S&F in replacement Vitreous china wash down water closet (pedestal pattern) white complete, includinguding connection to drain pipe and to flushing pipe anti syphonage pipe etc complete all as specified and directed

S&F in replacement plastic water closet white seat cover closed pattern with flat bottom cover and mild steel chromium plated or aluminized hinging device complete all as specified and directed

S&F in replacement Vitreous china wash basin white flat back 550mm x 400mm excluding tap, waste, chain & plug but including brackets complete all as specified and directed

S&F in replacement waste fitting/cuppling 32/40 mm dia brass chromium plated for glazed ware sinks/basins etc with long screwed shanks and fly nuts flange and bedded in red lead cement and other end fixed complete all as specified and directed

S&F in replacement PVC waste pipe 25 mm dia 750 to 800mm long fixed to waste fitting of wash basin includinguding socket suitable for waste fitting complete all as specified & directed

S&F in replacement chromium plated fancy type stop vlave /angle valves/ two way angle valve with cup cast copper alloy screwed down high pressure, screwed both ends for iron pipes or for unions for 15 mm bore pipe complete all as specified and directed.

S&F in replacement chromium plated fancy type long body bib taps with cast copper alloy screwed down, screwed for iron pipe or for brass ferrule for 15 mm bore pipe complete all as specified and directed.

S&F in replacement 100 mm dia shower rose of Chromium plated brass for fixing 15 mm pipe with shower arm size 195 mm long with bend of 45 degree with flange complete all as specified and directed.

S&F in replacement water jet for ETWC chromium plated with PVC connection complete all as specified and directed.

S&F in replacementCP heavy duty extension pieces 15mm bore and 25 mm long complete all as specified and directed.

S&F in replacement Chromium plated hand shower (health faucet) 1 mtr PVC tube with wall hook complete for ETWC complete all as specified and directed.

S&F in replacement PVC connections 15mm dia & 600mm long with PTMT nuts complete all as specified and directed.

S&F in replacement Chromium plated toilet paper holder stand complete all as specified and directed.

S&F in replacement Chromium plated towel ring complete all as specified and directed.

S&F in replacement glass shelf with chromium plated brackets of suitable size complete all as specified and directed.

Taking down carefully aluminium point wiring any type includinguding battens if any except for ceiling or where not feasible for light/ fan//bell/socket or power and includinguding unscrewing from board, fitting and fixture such as switches,socket, ceiling rose,lamp holder,pendants, bracket and regulator etc and removing material from site includinguding making good disturbed surface to match with the existing surface complete all as specified.

Material and labour for point wiring with single core PVC sheathed 1100 volt grade cable(FRLSH) with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and includinguding non metallic rigid PVC conduit medium duty ISI marked not less than 20mm dia, with all conduit accessories, screws, rawl plugs (concealed conduit wiring in walls and casing capping on ceiling or roof) includinguding pressed steel terminal sunken boxes and covered with 3 mm thick plastic laminated sheet cover of suitable size with new brass screws for mounting switch sockets and regulators and drawing continuous earth wire with and includinguding PVC sheathed 1100 Volts grade cable (FRLSH)with stranded copper conductor of size 1.5 Sq mm (Nominal area) and connected to main earth dolly complete all as specified for:- (a) One light / fan/ exhaust fan point controlled by one switch.

S&F in replacement 2'X2' LED recess/surface monted fitting 36 watt,230V with integrated electronic driver high transcluent frosted diffuser, connector block etec complete with all accessories internally pre-wired and includinguding connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

S&F in replacement round shape 6 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers holders, LED lamp suitable for roof ceiling includinguding connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply, laying and testing in replacement cable XLPE insulated screended PVC beded, galvainised steel strip or wire armoured electirc power cabel heavy duty with stranded aluminium conductor 1100 volts grade of size 70 sqmm 3.5 core complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth and getting out in soft/loose soil for laying of under ground cable and foundation of poles complete all as specified and as directed.

Returning, filling in, includinguding spreading levelling, watering and well ramming in layers not exceeding 25 cm thick in hard/dense soil

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

M&L for sand cushioning with layer of sand 8 cm thick before laying of cable and 15cm after laying of cable in trenches punning complete all as specified and as directed.

M&L for brick protection to cable using old size sub class 'B' bricks laid flat/lengthwise prependicular to the axis of cable complete all as specified and as directed.

UTTRAKHAND BUILDERS (BID ID -3121765)

Goel Enterprises (BID ID -3121310)

M/S Rajeev Sharma and Co. (BID ID -3122319)

Shikhar ji Enterprises (BID ID -3120910)