KCMC-15th CFC fund 2022-23,2023-24, 2024-25 Tied Grant Balance Fund

Amount

Supply and delivery of (5000LPMX80M)Vertical type water/Oil lubricated statically, dynamically, hydraulically balanced turbine pump capable of discharging the following duty condition as given below due to all causes with surface discharge head confirming to IS 1710 and as amended as on date with accessories as per IS 5120/1977 (Reaffirmed 2011 ) and as amended thereafter to suit the site condition. The speed, No. of stages, sizes of column pipes and line shaft indicated is based on site condition prevailing during investigation. The pump should be supplied with non reversible ratchet pin housing safety clutch, suction strainer etc. The Pump Bowl assembly shall be with bronze impeller running at 1450 rpm. The pump includes suitable head shaft, suitable 1.5 metre long SS line shaft required Nos. to suit the well depth, Rubber line shaft bearing of required Nos., C.I Bearing retainer of required Nos., 100 litre HDPE Pre- lubricating tank with 20mm PVC Rigid pipe connection along with GM gate valves, Suitable ERW column pipe of each 1.5m long of required Nos. to suit the well depth, Suction bell mouth of suitable size, M.S. clamps suitable for column pipe/line shaft -2 set and Spanner - 1 set etc complete

Erection of(5000LPMX80M) water Lubricated / oil lubricated vertical turbine pump with motor at site of work including preparation of suitable foundation and bed, fabrication of packer plates from raw materials , cutting required shims , assembling and joining of all required loose components such as bowl assembly, impellor shaft, line shaft, column pipes , head soft, discharge head, bearings, drive unit, delivery side pipes , suitable tappers required valves and specials, pressure gauges and flow meters , adjustment of pump shaft and leveling and alignment checkup greasing of relevant components, grouting of foundation bolts and sole plate with non shrink grout materials of conbextra GP-2 cement erection, connecting the relevant electrical cables with motor properly etc. complete and testing the out put and efficiency, site performance test for noise and vibration and trial run for minimum 10 days and commissioning satisfactorily for the various HP of the vertical turbine pumpsets as given below per IE rules as directed by TWAD Board officers .

Charges for complete lifting and dismantling of 90Hp-1 motor pump set. Such as Motor,thrust bearing assembly, motor stool, discharge case, top shaft, shaft coupling, column pipes, line shafts, Bowl assembly and spiders etc.complete,

Supply and fixing of bearing of replacement of damaged non driving end bearing . Including charges for replacement of bearing outer racer by the lathe, re fixing of new bearings and consumables like gaskets, recommended bearing grease and cotton waste, emery sheet and re- assembling of the motor to the bed . etc., complete., as directed by the departmental officers.

Supply, delivery of rubber bearing size of ID30mm to 50 mm x OD 75 mm to 90 mm x 175 mm length with suitable groove for shaft cooling as per standard specification ect. Complete.

Supply, delivery of rubber insertion sheet etc. Complete.,as directed by the departmental officers ect. Complete.

Supply and delivery of 20 mm dia and 90mm to 120 mm length of MS bolt & nut with two plate washers for 250 mm dia column pipe as directed by the departmental officers ect.Complete., at site.

Labour charges for through cleaning of the spiders, column pipes, shafts, discharge case,sole plate, motor bed including charges for consumables etc.complete . Including replacement where ever nesscessory

Servicing of the bowl assembly by removing of all wornout bushes by using hydraulic press and recondition of impeller guide portion. Providing new lock set with SS bolt and impeller cotter keys . including lathe work charges, loading,unloading and transport charges etc. complete,. Including replacement where ever nesscessory

Charges for re erection of of motor pump set. Such as Motor ,thrust bearing assembly , motor stool, discharge case ,top shaft , shaft coupling , column pipes, line shafts, Bowl assembly and spiders . including no load and load test for specified period etc.complete,.as directed by the dept. officers.

Supply and delivery of 400 mm dia CI Single Door/ Multi Door Non return valve conforming to IS 5312/2003(part I & II) to be fixed after Water meter/ Flow recorder on pumping main near Pump house with dash pot arrangement for 90% fast closing & 10% slow closing and with 5 years warranty

Jointing the C.I/ D.I Double flanged pipes and specials with rubber insertion to with IS- 638(1979) and M.S. bolts and nuts of IS 1364-1 (2002), including cost of jointing materials such as bolt and nuts Rubber insertion and labour charges etc., complete.

Desilting light or sandysoil or silt from infiltration wells below water level including the charges for special T&P and air compressor etc. complete.

supply and delivery of 630A, 4 Pole 50kA, Microprocessor Based, EDO Breaker

Supply and delivery of Automatic Power Factor Capacitor Panel the following site

Supply and delivery following electrical material as directed by the departmental officers

Digital Ammeter 3 phase

Digital Voltmeter 3 phase

Cable Route Indicator for LT Cable

2m x 1m Rubber Mat suitable for 11 KV installation confirming to IS

First Aid Box complete with all First Aid Medicines

Fire Extinguisher Co2, 4.5 kg. confirming to TAC Norms

Earth Discharge Rod

Aluminium alloy Solid Round Conductor with 8mm dia of material AlMgSi as per IEC 62561-2 with Conductor Holder, glue, connectors, joints etc.

Air termination rod 16/ 10 mm( Lightning rod) 2 mtr

125 amps change over swtich

Charges for filtration of Transformer oil to improve dielectric strength. including charges for conducting test for break down voltage, acidity value in the approved lab / TNEB lab and obtaining test certificate etc., complete. as directed by the departmental officers.

Charges for replacement of breather including silica gel and arresting the transformer oil leakage in the transformer top side , HT and LT insulator bushings side including labour charges , consumables like corke sheets,cotton waste, cleaning agent , level indicator glasses and metal paste etc., complete. as directed by the departmental officers.

Charges for Cleaning of Rusted parts of transformer yard structure and fencing. Painting of two coats best quality of Aluminium paints in the transformer yard structure and fencing.and synthetic enamel paint of RYB (red, yellow and blue) colour to structure bus bar and jumpers indication .including charges for consumables such as emery sheet, waste and Aluminium paint etc., complete. as per IE Standard specification.as directed by the departmental officers.

Charges for cleaning of earth pit and earth electrode for transformer body earth,neutral earth, Transformer yard structure earth, control room main MV pannel earth and pump room MV pannel earth including charges for replacement of corrosion bolt and nut in the earth pit and testing of earth their individual and combined resistance valve with earth as specified in the IE rules. and marking with enamel paint for reference etc., complete as directed by the dept. officers.

Suppiy and delivery of high grade continuous rating transformer oil as per IE Standard specification for topup in the transformer while oil circulation etc. compelte. as directed by the dept. officers.

The re arrangement of temporary arrangement of electrical connection as per IE standard in the transformer yard, food bridge, pump room, capacitors and bore well rooms including charges for necessary earth arrangement wherever necessary etc. complete. as directed by the dept. officers.

Supply and delivery of 1500X 60 Open well Submersible pump set conforming to IS 14220 /2002 and as amended thereafter and BEE 3 Star Rated capable of discharging the following duties due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze mixed type impeller, CI FG 200 grade casing and brass screws and rotor shall be of copper rod as per IS 613/1984 with ISI mark. The pump suitable for installation in sump with 1.1KV grade 3 core suitable copper flat submersible cable to a length of 15m with necessary cable joints. The non-return valve located at the top of the pump in the discharge outlet connection is to be designed with minimum friction. The pump should be directly coupled to 2880 RPM, three phase, 50 Hz (±5), 415V+6% & 415V-15% squirrel cage induction motor suitable for DOL upto 5 HP, Fully Automatic Air break Star Delta up to 20 HP and Auto Transformer starter for above 20 HP starting and for continuous operation.

Supply and delivery of Fully Automatic Auto Transformer Starter suitable for the motor offered. Floor mounting type air/ oil cooled Auto Transformer Starter with tapings at 50%, 65%, 80%, housed in robust steel chamber with arc and main contacts confirming to IS 8544 Part IV and as amended therafter for operation in AC three Phase 50 Hz (+/- 5%), 415V (+/- 10%) with the following components, under voltage release with no volt coil, over load relay with dash pot arrangements, single phasing preventor, LED ON/ OFF switches, Mounted Ammeter, Earth leakage relay, contactor assembly suitable for next standard KW rating, in coming and out going cable entry provisions, transformer tank including first filling of oil etc.

20 HP starter

Labour Charges for erection of bore well/Open well including fixing of suction pipe and foot valve upto a maximum depth of 7 metres and delivery pipes to the required length with valves, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPIC switches starter, Voltmeter, Ammeter, Capacitor single phasing preventor and laying and jointing the cables and twin earthing as per IE rules including providing bed blocks etc., complete and operating the pumps and trial run for 10 days including signing of completion of reports as required by EB authorities.

Supply and delivery of240sq.mm l.t. Cables 3.5,core 1.1 kv grade armoured aluminium conductor cross linked poly ethylene insulated pvc sheathed cables conforming to is 7098 (part i)/1988 and as amended thereafter with isi marking as directed by the department officers.

Supply and delivery of 185 sq.mm L.T Cables 3.5 core 1.1 kv grade armoured aluminium conductor cross linked poly ethylene insulated pvc sheathed cables conforming to is 7098 (part i)/1988 and as amended thereafter with ISI marking as directed by the departmental officers

Supply and delivery of 95 sq.mm L.T cables 3.5, core 1.1 kv grade armoured aluminium conductor cross linked poly ethylene insulated pvc sheathed cables conforming to is 7098 (part i)/1988 and as amended thereafter with isi marking as directed by the departmental officers

Supply and delivery of 50 sq.mm L.T cables 3.5 core 1.1 kv grade armoured aluminium conductor cross linked poly ethylene insulated pvc sheathed cables conforming to is 7098 (part i)/1988 and as amended thereafter with isi marking as directed by the departmental officers

Providing cable laying as directed by departmental officer

Dismantling and complete lifting of 120 HP -VT motor ,Thrust bearing assembly , motor stool discharge case ,top shaft , column pipes, line shafts, Bowl assembly and spiders etc.complete,. ,as directed by the dept.officers

50 HP motor Erection Labour Charges for erection of bore well/Open well including fixing of suction pipe and foot valve upto a maximum depth of 7 metres and delivery pipes to the required length with valves, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPIC switches starter, Voltmeter, Ammeter, Capacitor single phasing preventor and laying and jointing the cables and twin earthing as per IE rules including providing bed blocks etc., complete and operating the pumps and trial run for 10 days including signing of completion of reports as required by EB authorities..

50 HP motor Dismantling of Labour Charges for erection of bore well/Open well including fixing of suction pipe and foot valve upto a maximum depth of 7 metres and delivery pipes to the required length with valves, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPIC switches starter, Voltmeter, Ammeter, Capacitor single phasing preventor and laying and jointing the cables and twin earthing as per IE rules including providing bed blocks etc., complete and operating the pumps and trial run for 10 days including signing of completion of reports as required by EB authorities..

Supply and delivery of 150 mm dia G I PIPES (MEDIUM) AS PER IS 1239/PART I/2004 as directed by the departmental officer

Lowering 150 mm dia GI pipes and specials in the trenches and laying to proper grade and alignment, jointing with GI Specials and as directed by the TWAD Officers

150 mm dia Welding of GI pipes as directed by the departmental officers for the sizes

Interconnecting the 450 mm DI pipes with GI pipe on both ends using 150 mm dia GI pipe including cost of MS flange fabrication charges and painting with anti-corrosive paints etc complete

Manufacturing and Supply of Metal Junction Box. Size: L400 x H800 x D225mm. with 32x6mm Copper Flat as directed by the departmental officers .

A S POWER SOLUTIONS (BID ID -1257565)