ADDITION ALTERATION TO BUNGALOW NO 07 AND 08 PROVN OF SINGLE RAMP NEAR MT OF 33 MTN BDE FALSE CEILING TILING AND OTHER MISC ALLIED WORKS IN BUILDING NO HT-29 AT MIL STN DHARAMSHALA

Amount

Demolition of cement concrete (unreinforced) in ground floors & paving not exceeding 15 cms thick (below or above ground level) complete, all as specified and directed by Engr-in-Charge.

Taking down chowkats with shutters (without taking off shutters from the frames) of any description area not exceeding 1.5 Sqm each, complete all as specified and directed by Engr-in-Charge.

Taking down Shutter of any description execeeding 1Sqm and not execeeding 2 Sqm complete all as specified and directed by the Engr-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) of any description areaexceeding 1.5 but not exceeding 4.0 Sqm each, complete all as specified and directed by Engr-in-Charge.

Solid PVC door frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as per drawing shown on page No 160 of SSR Part-II (rates) and as directed by Engr-in-Charge. (Note:- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life)

Factory made solid panel PVC door shutter 30 mm thick (stile) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of wood grain printed PVC sheet used instead of Plain colour PVC sheet & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900 ) used instead of exposed portion of PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing on page No. 156 of MES SSR Part-II 2010, complete all as specified and directed by Engr-in-charge.

Pressed steel frame of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc; complete all as specified and directed by Engr-in-Charge.

Factory made 2nd class hard wood ( Sal/Hallock) plain, framed, panelled 35mm thick shutter (two panels) with lock rail and panels of 9mm BWP commercial playwood or 12mm veneered particle with commercial face veneers on both sides. The size of rail and style as per IS-1003 (Part-I) Kiln seasoned and chemically pressure treated all as specified and as directed by the Engineer-in-Charge.

2nd class hard wood, plain, solid, straight, chowkats and frames, wroguht, framed rebated on the solid rounded or chamfered put together with glue pinned at joints.complete all as specified and directed by Engr-in-Charge.

Taking down cement plaster on brick or stone surfaces etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed by Engr-in-Charge.

10mm thick rendering in CM 1:6 on fair faces of brick or concrete surface finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

Two coats of oil bound distemper on newly plastered surface of walls over a coat of chalk whiting including preparation complete all as specified and directed by the Engr-in-Charge.

Two coats of oil bound distemper on old decorated wall surfaces over a coat of chalk whiting including preparation by brooming down with steel wire brushes, scraping down smoke, soot, molds, moss and efferescent salts and trating oil and greasy spots etc. as specified and directed by Engr-in-Charge.

15mm thick rendering in CM 1:4 on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, complete all as specified and directed by Engr-in-Charge.

Two coats of all weather exterior paint over a coat of primer to newly plastered/old sufaces of walls including preparation of sufaces etc. complete all as specified and directed by Engr-in-Charge.

Demolition of Trezzo or thickness in any position complete all specified and directed by Engr-in-charge.

Coloured Glazed ceremic tiles of size 350x250x7mm/450x350x7mm thick as in vertical surface etc, set jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles incl 10mm thick rendering in 1 CM complete, all specified and directed by Engr-in-Charge.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering complete, all as specified and directed by Engr-in- Charge.

PCC, M-15, type B-1( using 20 mm graded crushed stone aggregates), 25mm thick as in flooring, finished to receive floor finishes complete all as specified and directed by Engr-in-Charge.

Non skid coloured ceremic tiles 6 to 7mm thick area of each tile exceeding 0.11 sqm but n.exc. 0.18 sqm in floors etc, set, jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles including 15mm thick screed bed in CM 1:6 complete all as spcified and directed by Engr-in-Charge.

Chequered cement concrete tiles maching pressed glossy finished (heavy duty) of size 300x300x30mm thick with grey cement and pigment set jointed & pointed in neat cement slurry in floors over 15mm thick screed bed in cement mortar 1:6 complete, all as specified and directed by Engr-in-Charge.

15mm bore fancy type chromium type Angle stop valve cast copper alloy, screwed down, high pressure with crutch or butterfly handle srewed both ends for iron pipe or for unions ,complete all as specified and directed by Engr-in-Charge.

Brick work with sub class 'B' bricks, straight or curved on plan exc. 6m mean radius, built in cement mortar 1:4, complete all as specified and directed by the Engr-in-Charge.

15mm dia bore fancy bib Taps, cast copper alloy with crutch or butterfly handle scewed down , scewed for iron pipe or for brass ferrule and fixed. complete all as specified and directed by Engr-in-Charge.

15mm bore GI tubing, medium grade, galvanised with all fittings and fixtures fixed to wall and celling or laid in floor, complete all as specified and directed by Engr-in-Charge.

10 liters capacity PVC flushing cistern valve less symophomic action type low level white complete alongwith all fitting including fixing in position including jointing to WC complete all as specified and directed by Engr-in-Charge.

PVC (SWR) floor trap ,plain with grating incliding jointing with solvent cement, complete all as specified and directed by the Engr-in-Charge.

Vitreous China wash hand basin, angle back, size 600x480mm white, including 15mm pillar taps, with 32mm chromium plated waste coupling, waste pipe of bore 32mm, PVC Connection pipe 450mm ling with brass nuts on both side, complete all as specified and directed by Engr-in-charge.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and directed by Engr-in-Charge.

Viterous china wash down water closet pan (Pedestal pattern), white, excluding fixing bolts flushing cistern) including connection to drain and flush pipe, seat and cover, CP jet alonwith 1 mtr long CP insulated flush pipe (fixed in repair) complete all as spcified and directed by Engr-in-Charge.

PVC connection 15mm bore with PTMT nuts 450mm long complete all as specified and directed by Engr-in-Charge.

Brass CP Mixture for mixing hot and cold water scewed down for pipe and fixed , complete all as specified and directed by Engr-in-Charge.

15mm dia chromium plated shower rose, 125mm size, shower arm 15mm size, 195mm long with bend of 45 degree with flange of PTMT any colour, complete all as specified and directed by Engr-in-Charge.

Toilet paper holder, box type, complete all as specified and directed by Engr-in-Charge.

Towel rail, 450mm long of PTMT fixed with and including CP brass screws and wooden/plastic cleats (min weight 170grams) (fixed in repairs) complete all as spcified and directed by Engr-in-Charge.

Soap Dish any type fixed to plugs with chromium plated brass screws complete all as specified and directed by Engr-in-Charge.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with CP bracket guard and 03 Nos railing in front & sides 60cm long complete all as spcified and directed by Engr-in-Charge.

PVC (SWR) pipe 75mm bore single in any type with rubber ring joint laid in trenches/floor complete all as specified and directed by Engr-in-Charge.

100mm butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-11 complete, all as specified and directed by Engr-in-Charge.

150mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr-in- Charge.

150mm long aluminium alloy handles, cast type, anodised complete all as specified and directed by Engr-in- Charge.

300mm long mild steel sliding door bolts, plate type, stove enamelled black, with bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts , four on bolt plate and two on staple plate and fixed, complete all as specified and directed by Engr-in-Charge.

75mm butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed by Engr-in-Charge.

100mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr-in-Charge.

100mm long aluminium alloy handles, cast type, anodised complete all as specified and directed by Engr-in-Charge.

Excavation in trenches not exceeding 1.5m deep & getting out in any type of soil complete all as specified and directed by Engr-in-Charge.

Excavation over area not exceeding 1.5m in depth and getting out in any type of soil complete all as specified and directed by Engr-in-Charge.

PCC M-10, types C2 (40mm graded crushed stone aggregates) as in fundation, filling and mass concrete, complete all as specified and directed by Engr-in-Charge.

Brick work fly ash bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:4 complete all as specified and directed by the Engr-in-Charge.

Hard Core of gauge not exceeding 63mm, deposited, spread and levelled in layers not execeeding 15cm thick, watered and rammed to a true surfaces with broken stones, complete all as specified and directed by Engr-in-Charge.

Returning, filling in (soil), including spreading, levelling, watering and well ramming in layers not exc 25 cm thick in any type of soil complete all as specified and directed by Engr-in-Charge.

Removing of excavated soils to a distance not exceeding 50mtr and depositing where directed at a level not exceeding 1.50mtr above the starting point complete all as specified and directed by Engr-in-Charge.

Form work to rough finished surface edges of concrete flats, treads breaks in floors, window cills, concrete railings opening in concrete walls,Hoor and roofs as specified and directed by Engr-in-Charge.

RCC(M-25) degign mix as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, conopies, deck slabs and in shelves and the like.complete all as specified and directed by the Engr-in-Charge.

Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking and binding spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by the Engr-in-Charge.

All as per serial item 56 here-in-above but of size 6 to 8mm dia as in reinformement, complete all as specified and directed by the Engr-in-Charge.

All as per serial item 56 here-in-above but TMT bars 6 to 8mm dia as in stirrups, complete all as directed by Engineer-in-Charge. NOTE FOR SERIAL ITEM NO. 47 to 58:- Ramp work shall be executed complete all as per drawing No. CEPZ/C-TD/016/13 SHEET 1/1{(Single Ramp(Plan, elevation & details)}

Galvanized corrugated mild steel sheeting 0.63 mm thick with two corrugations side lap, fixed with ' L' or 'J' hooks and washers, as in roof covering with grade of zinc coating 120gm/ sqm, complete all as specified and directed by Engr-in- Charge.

Three coats of white wash on newely plastered surface of walls including prepration of surface, complete all as specified and directed by Engr-in-Charge.

Cutting holes into or through brick walls or stone walls built in cement mortar or lime mortar or walls of lime concrete, superfacial area n. exc. 150 sqcm all as specified and of depth as directed by Engr-in-Charge.

2nd class clean sawn soft wood as in scantling,complete all as specified and directed by Engr-in-Charge.

Preparing surfaces of wood and wood based materials new or old, of any description and girth, not other wise described and treated with two coats of creosote oil complete all as specified and directed by Engr-in-charge.

Non asbestos fibre cement building boards, 4mm thick fixed to timber frame work complete all as specified and directed by Engr-in-Charge.

2nd class soft wood clean sawn chamfered fillets sectional area exc. 3 sqcm & n.exc. 6sqcm, complete all as specified and directed by Engr-in-Charge

Two coats of synthetic enamel paint after preparing the new surfaces of any description n exc 10 cm width or girth when unconnected with other painting,complete all as specified and directed by Engr-in-Charge

Two coats of white wash on newely plastered surface on ceilling including prepration of surface, complete all as specified and directed by Engr-in-Charge.

Demolition of tiles of any description or thickness laid bedded and pointed in any mortar,complete all as specified and directed by Engr-in-Charge

Granite (of any type ) 20mm thick, machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone on kitchen plate form including grinding and polishing over 20mm thick screed bed in CM 1:4 complete all as spcified and directed by Engr-in-Charge.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of chalk whitening preparatory to distempering including preparation of surfaces complete, all as specified and directed by Engr-in- Charge.

Demolition of reinforced cement concrete as in shelves,complete all as specified and directed by Engr-in-Charge.

Demolition of brick work or stone/ boulders masonry, built in cement mortar including all quoins, arches, pillars, etc but excluding ashlar facings dressed stone work and precast concrete articles, complete all as specified and directed by the Engr-in-Charge.

3mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in square n.exc.0.50 sqm in each pane complete, all as specified and directed by Engr-in- Charge.

Vitrified ceremic coloured tiles, 10mm thick (Square / rectangular) area of each tile exceeding 0.36 Sqm but not exceeding 0.42 Sqm, in floors etc. set and joined in neat cement slurry and pointed in white or coloured cement to match the shade of tiles , laid over and including 15mm thick screed bedding layer in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

Rendering 10 mm thick on fair faces of brick or concrete surface in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed by Engr-In-Charge.

Coloured Glazed ceremic tiles 300x200x 7mm thick as in vertical surface etc, set, jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles including 15mm thick rendering in CM (1:4), complete all as spcified and directed by Engr-in-Charge.

15mm bore, stop valves, fancy type, chromium plated with crutch or butterfly handle screwed both ends for iron pipes or for unions. complete all as specified and directed by Engr-in- Charge.

32 mm waste fitting , brass, CP for wash hand basin,complete all as specified and directed by Engr-in-Charge.

PTMT grating 100 mm dia,complete all as specified and directed by Engr-in-Charge.

25 mm dia coloured fancy type curtain rail,complete all as specified and directed by Engr-in-Charge.

25 mm dia fancy side globes for curtain rail,complete all as specified and directed by Engr-in-Charge.

Fancy type bracket for curtain rail,complete all as specified and directed by Engr-in-charge.

surinder kumar jindal bros