Construction of MRT Office Complex at Circle Office of Operation Circle, Kakinada

Earth work excavation in ordinary soils by manual means upto 3m depth for foundations and depositing on bank for all lifts and with an initial lead of 10m including all operational, incidental, labour charges such as shoring ,sheeting, planking, strutting, etc. complete for finished item of work including seigniorage excluding dewatering charges etc as per SS - 20 B (APSS 308).

Filling with useful available excavated earth (excluding rock) in trenches, sides of foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T & P etc., complete for finished item of work. (APSS NO. 309 & 310)

Filling with sand in foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T & P etc., complete for finished item of work. (APSS NO. 309 & 310)

Plain Cement concrete (1:4:8) using 40 mm metal with concrete mixer including cost and conveyance of all materials and all labour charges complete.

Supplying, cutting and placing HYSD bar reinforcement as per drawings and technical specifications for Bars below 36 mm dia including over laps and wastage, where they are not welded including cost and conveyance of all materials to site and all labour charges complete.

Providing Pre construction Anti termite is a process in which 1. chemical toxic to subterranean termites is apply/ inject into soil during early stage of building Construction 2. Treatement of soil Beneath the building and around the foundations conduct and chemical use as per BIS - IS 6313 (Part -2) 2013 code specification & CIB RC registered termiticide which creates a continuous chemical barrier beneath the building which kills or repels terminates & impervious to tremite entryImidacloprid 30.5% SC (IS 63131) dissolve 2.1 Ml/1 liter of water and apply emulsion/solution @ 7.5 Litres/Square meter (Sqm) of internal, external vertical surface of the colums , plinth beams (Back filling) walls and floor junction, external perimeters, along reatining wall @ 5.0 Liters/Sqm of the horizontal surface of basement top surface of the basement filling below flooring bed (Plinth) & @ 2.0 Litres/ Line meter at expansion joints. The substructure of a depth of 500mm around coulmns & 300mm deep around plinth beams, basements & floor filling area including excavation channel along the wall & rodding etc. cost & Conveyance of all materials to the site, cost of labour for sparying, rodding etc. complete for furnished item of work as per the approval of the Engineer-in-charge

Brick Masonry in CM (1:5) with Fly ash cement/lime solid blocks with compressive strength of 75 kg/sq.cm - IS:12894-1990 - CLASS - 7.5 - 290 x 200 x 140 mm including seignorage charges including cost and conveyance of all materials to site and all labour charges complete.

Augoring and boring of 375mm dia holes in site Bored cast-in-situ R.C.C. Piles with R.C.C. M-20, Nominal Mix (1:1.5:3) using 20mm size aggregate for building foundations in loamy, clayey soils like Black cotton soils and ordinary soils as per IS 2911 - 1980 and as per approved designs including cost and conveyance of all materials to site excluding cost of steel and including all operations, incidental, labour charges, hire charges of machinery, augor bore drill and shell equipment, etc, complete for all depths and for finished item of work.

Under reaming for Bored cast-in-situ R.C.C. Piles of 375mm dia with R.C.C. M-20, Nominal Mix (1:1.5:3) using 20mm size aggregate for building foundations in loamy, clayey soils like Black cotton soils and ordinary soils as per IS 2911 - 1980 and as per approved designs including cost and conveyance of all materials to site excluding cost of steel including all operations, incidental, labour charges, hire charges of machinery, augur bore drill and shell equipment, etc, complete for all depths and for finished item of work.

Augoring and boring of 300mm dia holes in site Bored cast-in-situ R.C.C. Piles with R.C.C. M-20, Nominal Mix (1:1.5:3) using 20mm size aggregate for building foundations in loamy, clayey soils like Black cotton soils and ordinary soils as per IS 2911 - 1980 and as per approved designs including cost and conveyance of all materials to site excluding cost of steel and including all operations, incidental, labour charges, hire charges of machinery, augor bore drill and shell equipment, etc, complete for all depths and for finished item of work.

Under reaming for Bored cast-in-situ R.C.C. Piles of 300mm dia with R.C.C. M-20, Nominal Mix (1:1.5:3) using 20mm size aggregate for building foundations in loamy, clayey soils like Black cotton soils and ordinary soils as per IS 2911 - 1980 and as per approved designs including cost and conveyance of all materials to site excluding cost of steel including all operations, incidental, labour charges, hire charges of machinery, augur bore drill and shell equipment, etc, complete for all depths and for finished item of work .

VRCC M- 25 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. PILE CAPS

VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. PLINTH BEAM

CELLAR FLOOR - LINTEL BEAMS VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

FIRST FLOOR LINTEL BEAMS VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

SECOND FLOOR LINTEL BEAMS VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

THIRD FLOOR LINTEL BEAMS VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

CELLAR FLOOR - COLUMNS VRCC M- 25 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

FIRST FLOOR COLUMNS VRCC M- 25 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

SECOND FLOOR COLUMNS VRCC M- 25 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

THIRD FLOOR COLUMNS VRCC M- 25 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

CELLAR FLOOR - SUNSHADES/CHAJJAS VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

FIRST FLOOR SUNSHADES/CHAJJAS VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

SECOND FLOOR SUNSHADES/CHAJJAS VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

THIRD FLOOR SUNSHADES/CHAJJAS VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

CELLAR FLOOR - ROOF BEAMS VRCC M- 25 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

FIRST FLOOR ROOF BEAMS VRCC M- 25 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

SECOND FLOOR ROOF BEAMS VRCC M- 25 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

THIRD FLOOR ROOF BEAMS VRCC M- 25 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

CELLAR FLOOR ROOF SLAB VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

FIRST FLOOR ROOF SLAB VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

SECOND FLOOR ROOF SLAB VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

THIRD FLOOR ROOF SLAB VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

Providing impervious coat to exposed RCC roof slab surface with CM(1:3), 20mm thick with 1kg of water proof compound per bag of cement laid over roof when it is green including cost of all materials, seigniorage charges, conveyance charges of materials and including all operational, incidental and labour charges for mixing mortar, laying, rendering smooth and thread lining, curing, rounding off junctions of wall and slab etc,, complete for finished item of work

CELLAR FLOOR Brick Masonry in CM (1:6) with 2nd class Bricks traditional size 23 x 11 x 7 cms including cost and conveyance of all materials to site and all labour charges complete.

FIRST FLOOR Brick Masonry in CM (1:6) with 2nd class Bricks traditional size 23 x 11 x 7 cms including cost and conveyance of all materials to site and all labour charges complete.

SECOND FLOOR Brick Masonry in CM (1:6) with 2nd class Bricks traditional size 23 x 11 x 7 cms including cost and conveyance of all materials to site and all labour charges complete.

THIRD FLOOR Brick Masonry in CM (1:6) with 2nd class Bricks traditional size 23 x 11 x 7 cms including cost and conveyance of all materials to site and all labour charges complete.

CELLAR FLOOR 11.5 cm wide Brick masonry for super-structure on ground floor in cm (1:4) using second class traditional size bricks including cost of all materials and it's conveyance, labour and all operations for constructing half brick masonry, mixing cement mortar, curing etc.,complete.

FIRST FLOOR 11.5 cm wide Brick masonry for super-structure on ground floor in cm (1:4) using second class traditional size bricks including cost of all materials and it's conveyance, labour and all operations for constructing half brick masonry, mixing cement mortar, curing etc.,complete.

SECOND FLOOR 11.5 cm wide Brick masonry for super-structure on ground floor in cm (1:4) using second class traditional size bricks including cost of all materials and it's conveyance, labour and all operations for constructing half brick masonry, mixing cement mortar, curing etc.,complete.

CELLAR FLOOR Plastering with CM (1:3), 12 mm thick in one coat for inernal faces of ceilings etc.,including cost and conveyance of all materials all labour charges etc, complete.

FIRST FLOOR Plastering with CM (1:3), 12 mm thick in one coat for inernal faces of ceilings etc.,including cost and conveyance of all materials all labour charges etc, complete.

SECOND FLOOR Plastering with CM (1:3), 12 mm thick in one coat for inernal faces of ceilings etc.,including cost and conveyance of all materials all labour charges etc, complete.

THIRD FLOOR Plastering with CM (1:3), 12 mm thick in one coat for inernal faces of ceilings etc.,including cost and conveyance of all materials all labour charges etc, complete.

CELLAR FLOOR Plastering with CM (1:5), 12 mm thick in one coat for inernal faces of walls, ,including cost and conveyance of all materials all labour charges etc, complete.

FIRST FLOOR Plastering with CM (1:5), 12 mm thick in one coat for inernal faces of walls, ,including cost and conveyance of all materials all labour charges etc, complete.

SECOND FLOOR Plastering with CM (1:5), 12 mm thick in one coat for inernal faces of walls, ,including cost and conveyance of all materials all labour charges etc, complete.

THIRD FLOOR Plastering with CM (1:5), 12 mm thick in one coat for inernal faces of walls, ,including cost and conveyance of all materials all labour charges etc, complete.

CELLAR FLOOR Plastering with CM (1:5), 20 mm thick in one coat for external faces of walls including cost and conveyance of all materials all labour charges etc, complete.

FIRST FLOOR Plastering with CM (1:5), 20 mm thick in one coat for external faces of walls including cost and conveyance of all materials all labour charges etc, complete.

SECOND FLOOR Plastering with CM (1:5), 20 mm thick in one coat for external faces of walls including cost and conveyance of all materials all labour charges etc, complete.

THIRD FLOOR Plastering with CM (1:5), 20 mm thick in one coat for external faces of walls including cost and conveyance of all materials all labour charges etc, complete.

Laying P.C.C.(1:2:4) using 10 to 12 mm HBG metal including cost and conveyance of all materials to site and all labour charges complete for finished item of work.

Flooring with Supply of Double charged / multi charged stain free full body porcelain vitrified tiles with double layer pigment of Size 600 x 600 mm and thickness between 8-10 mm and 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs, Make: Somany,HR, Jhonson,Naveen Ceramics, Kajaria, Nitco, Sphinx, RAK or equivalent set over base coat of cement mortar (1:8), 12 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3.kgs per sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, sand water and tiles etc., complete, for finished item of work including the cost of conveyance of all materials.

Flooring with 8mm thick Non-skid edge cut rectified ceramic tiles Ist quality , set over base coat of cement mortar (1:8), 12 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3kgs per sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, sand water and tiles etc., complete, including seigniorage charges, etc., complete for finished item of work, including the cost of conveyance of all materials.

CELLAR FLOOR Providing and applying synthetic plaster putty or plaster of paris putty or lime punning of average 1 to 2mm thickness over plastered surface to prepare the surface even and smooth after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, sand the surface, clean & wipe off loose dust, applying knifing paste filler by putty knife/muslin pad, air dry for 2-3hrs, sand with 180 and 320 No., emery paper for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work for internal walls.

FIRST FLOOR Providing and applying synthetic plaster putty or plaster of paris putty or lime punning of average 1 to 2mm thickness over plastered surface to prepare the surface even and smooth after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, sand the surface, clean & wipe off loose dust, applying knifing paste filler by putty knife/muslin pad, air dry for 2-3hrs, sand with 180 and 320 No., emery paper for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work for internal walls.

SECOND FLOOR Providing and applying synthetic plaster putty or plaster of paris putty or lime punning of average 1 to 2mm thickness over plastered surface to prepare the surface even and smooth after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, sand the surface, clean & wipe off loose dust, applying knifing paste filler by putty knife/muslin pad, air dry for 2-3hrs, sand with 180 and 320 No., emery paper for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work for internal walls.

CELLAR FLOOR Painting with acrylic EXTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre exterior grade of approved brand and colour/shade two coats over a base coat of appropriate primer (grade-II) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work.

FIRST FLOOR Painting with acrylic EXTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre exterior grade of approved brand and colour/shade two coats over a base coat of appropriate primer (grade-II) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work.

SECOND FLOOR Painting with acrylic EXTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre exterior grade of approved brand and colour/shade two coats over a base coat of appropriate primer (grade-II) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work.

THIRD FLOOR Painting with acrylic EXTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre exterior grade of approved brand and colour/shade two coats over a base coat of appropriate primer (grade-II) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work.

CELLAR FLOOR Painting with synthetic polymer plastic INTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and shade two coats over a base coat of appropriate interior primer(grade-I) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work.

FIRST FLOOR Painting with synthetic polymer plastic INTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and shade two coats over a base coat of appropriate interior primer(grade-I) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work.

SECOND FLOOR Painting with synthetic polymer plastic INTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and shade two coats over a base coat of appropriate interior primer(grade-I) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work.

THIRD FLOOR Painting with synthetic polymer plastic INTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and shade two coats over a base coat of appropriate interior primer(grade-I) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work.

Providing R.C.C. plates of 38mm thick with R.C.C.(1:1.5:3) (including cost of steel reinforcement ) and plastering with CM(1:5),12mm thick including cost and conveyance of all materials to site and all labour charges complete.

Providing of RCM facia or drop wall 5cm thick in CM (1:3) including seignorage charges with rabbit wire mesh (chicken mesh) of not less than 30gauge & nominal reinforcement as directed by Engineer-in-charge with dubara sponge finishing, including cost & conveyance of all materials to site, scaffolding charges and all labour charges complete.

Providing and fixing factory made UPVCwhite colour sliding glazedwindow upto1.50m in height dimension comprising of uPVC multi chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60±0.2mm thick galvanized mild steel section made from roll forming process of required length (shape & sizeaccording to uPVCprofile), appropriate dimension of UPVC extruded glazing beads and UPVC extruded interlocks, EPDMgasket, woolpile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be40kg), G.Ifasteners 100x8mm size for fixing frame to finished wall and necessary stainless steel screwsetc. Profile offrame & sash shall be mitred cut andfusion welded at all corners, including drilling of holes for fixing hardware's and drainage of wateretc. After fixing frame the gap between frame and adjacent finished walls all be filled with weather proof silicon sealent over backer rod of required size and ofapproved quality, all complete as per approved drawing & direction of Engineer -in - Charge inclusive of cost of Single/double glasspanes, wiremesh and silicon sealent .Note: For uPVC frame and sash extruded profiles minus 5%tolerancein dimension i.e. in depth &width of profile shall be acceptable.Variation in profile dimension in higher side shall be accepted but no extra payment onthis account shallbemade.Two track two panels sliding window made of (big series)frame 67 x 50 mm & sash 46 x 62 mmboth having wallthickness of 2.3 ± 0.2 mm and singleglazing bead / doubleglazing bead of appropriate dimension .(Area of window upto 1.75 sqm ).

Supply and fixing of M.S. grill to Ground floor windows with 10mm square solid rods with 25mm x 25mm x 5mm L Angle and approved design given by the department and as directed by the engineer at site including cost and conveyance of all materials and all labour charges etc., complete. (1.22X1.22 )

Flush door: supply and fixing of 35 mm thick flush door single shutter, solid bond wood block board type with teak veneer on both faces including 5mm thick glass and supplying positioning and fixing door frame with well seasoned assam teak/beeja sal/sal wood scantlings of size 100 mm x 75 mm, including 6 nos. Of ms 'z' hold fasts of size 250x50x8 mm,including aluminium 3 nos. Of 125 mm butt hinges, 1 no. Door stoper, 2 no. 100 mm long door handles , 1 no. Aldrop of size 250 mm long , 1 nos. Of 200 mm long tower bolts, with bolts, nuts, nf screws including cost and conveyance of all materials to site, labour charges etc., including minor extra fixtures required if any as directed by the engineer-in-chrge of the work complete for finished item of work

Supply and fixing of CEMENT BONDED PRE-LAMINATED PARTICLE BOARDS aluminum glazed partitions using 10 MM CEMENT BONDED PRE-LAMINATED PARTICLE BOARDS and 5.00 mm thick plain glass to full height. Using with LAM to a height of 0.91 meter at bottom panel and remaining height with glass and aluminum sections anodized to 12 to 15 microns and of sections of size 37mm x 62mm and 1.5mm thickness with one meter centre to centre duly fixed with clip beading on both sides including fixing the frame to pillars by M.S. flats, bolts and nuts including cost and conveyance of all materials etc., complete as directed during execution.

Supply and fixing Aluminium Single Shutter door partly Glazed &Panneled with aluminium anodised sections of Jindal sections Shutter frame top of size 44.45 mm x 47.62 mm x 1.95 section 19571 , bottom of size 44.45 mm x 114.30 mm x 2.15 section 19574 and verticals of 19569 of size 44.45 mm x 47.62 mm x 2.02 and fitted with 10mm thick both sides prelaminated cement particle board and 5mm thick plain glass for shutter and other acccessories like supply and fixing aluminium handles, door stoppers, latches, etc., for each shutter, and all labour charges for fixing the fixtures with required no.of screws, bolts and nuts and including labour charges for fixing the frame in position, fixing shutter to frame etc. completed for finished item of work

Providing and fixing Aluminium Extruded Section Body Tubular Type Hydraulic Door Closer (IS: 3564) with double speed adjustment with necessary accessories and screws etc. complete (Type-3: for width of doors 851 to 1000 mm)

Providing and fixing of Wood Polymer Composite (WPC) solid doors with frame. Door shutter consists of Wood Polymer Composite (WPC) solid, frosty white single extruded factory made in 18 MM thickness (Density 650 kg/Cum, Weight 35Kg) and Door Frame consists of solid Wood Polymer Composite (WPC) single extruded section of size with encapsulation of 8MM rigid layer on all the six surfaces. The door frame will have a rebat of 32MM. Door Frame section of 45x75 MM . The two Vertical members are to be joined together with the horizontal member using 8x50 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member and with fixtures 1no aluminium aldrop 200mm lond and 2nos tower bolt 150mm long, the rate is inclusive of cost and conveyance of all materials to site and all labour charges complete.

Supplying and fixing Gyp Board Suspended regular single layer false ceiling (GS-MFSC-4.1 as per India Gypsum) using 12.5 mm thick Gyp Board conforming to IS 2095 - 1982 fixing to Gyp steel GI perimeter channels of size 20 mm x 27 mm x 30 mm(web) of 0.55 mm thick along the perimeter of ceiling screw fixed to brick work/ partition at 610 mm c/c and suspending the frame work using Intermediate channels (45 mm x 15mm x 15mm x 0.9 mm) from soffit at 1220 mm c/c with ceiling angle (25 mm x 10 mm x 0.55 mm) fixed with GI Cleat and steel expansion fasteners & connecting clip to the ceiling channels (with knurled web of 51.5 mm x 26 mm x 10.5 mm x 0.55 mm) fixed in direction perpendicular to the intermediate channel at 457 mm c/c and fixing the 12.5 mm tapered edge Gypboard with 25 mm drywall screws at 230 mm c/c & jointing and finishing using joint compound and paper tape to have a flush look including filling the tapered & square edges with jointing compound, two coats of drywall topcoat complete for finished item of work as per India Gypsum Ltd specification.

Supplying & fixing collapsible steel shutters with vertical, double channel of 20 x10x2 mm of 100 mm centre, Bracers with flat iron 40x40x6 mm with 38 mm dia steel pulleys, the top, bottom and side vertical frames of the collapsible gate with 65x65mmx8mm MS Angle and middle guide rail at site height with 65mmx8mm MS flat for the pulleys to guide and fixed with locking arrangements, stoppers, handles, all accessories all fixtures and painted with one coat of approved steel primer etc., complete for finished item of work.

Supply, fabrication and fixing of stainless steel railing of approved design with Stainless Steel Tubes, sections, plates, sheets & pipes of all sizes & diameters for grade -304 including all accessories and all labour charges complete for finished item of work.

Vibrated Plain Cement concrete (1:2:4) using 20mm size HBG metal with concrete mixer including cost and conveyance of all materials and all labour charges complete.

Supply and fixing( Positioning) modular panel based 4 units work station of size 4’x 4' x4’ double skinned partition of 62 mm (+/-5%) thick made out of extrude Aluminium sections powder coated with 12mm thick pre-laminated particle board panels/soft board / marker board panels, all the exposed metal surfaces of supports, top covers and hardware for fixing furniture to partition is to be powder coated with approved colour/Shade of 50 micron thick and provision for built in cable management provided with 2 No integrated wire ways of 130mm high, provided one each at skirting level and other at just below / above the work top (table ) level. The minimum free space required in the wire ways to accommodate power, data and communication cables is to be 30mmx120mm with injection moulded ABS end caps and with side partitions for every work station and with the front walls below the table top only (Switches and sockets of RAW power/ UPS /Data /Telephone shall be recessed).Provision should be made for three 5 amp socktes (one with switch control) and telephone jack, just below/above table top and one 5amp switch and one number RJ 15 and one No RJ 45 socket for LAN point below table top. The table top with PLB 25mm thick post formed particle board and the surface top with all exposed edges duly edge banded. The pin board is made of 12 mm thick soft board covered with approved colour/ shade /design/ texture fabric. The partition is to be provided with leveling bolts to account for any unevenness in the floor. The work station provided with table top of width of 500 mm and height of table top is 750 mm from the floor level. Key board tray with high impact plastic and C P U stand/ trolley and PLB 3 draw pedestal unit of size 450 x 500 x 650 mm as per approved design, make and accessiores and as per drawing and directions of Eng-in- charge .

Supply of Storwel plain shall have an overall size of 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The Storwel Plain should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.Overall Dimensions of Storwel= 916mm(W)x486mm(D)x1981mm(H) shelf thickness- 0.7mm Back thickness - 0.8mm, Door thickness- 0.8mm.

Supply of Slotted Angle Rack of Size: L 900 x D 450x H 1800 4 shelves including top & bottomHaving 2 stiffener in each side. Angles : 40mm x 40mm x 2mm(Thick)., Shelf : 1mm CRCA sheet

Supply of Chair Type-I Mid back (OXBO) with SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam.SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D).BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn.BACK SIZE : 46.5 cm (W) x 70.5 cm (H).HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. CENTRE-TILT mechanism: The mechashould be m should be designed with the following features:• 360° revolving type, • 17° ±2° maximum tilt on pivot at centre,• Upright position locking. Tilt tension adjustment. .PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSY: The bellow should be 3 piece telescopic type and injection moulded in Black Polypropylene. PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.)TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black nylon.Overall Dimensions of Chair Seat Height - min 43.3 to max 54.3cm.Height - min 99.5 to max 110.5cm.Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm

Supply of Chair Type-II Low back (OXBO)SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D).BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn.BACK SIZE : 46.5 cm (W) x 60.5 cm (H). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression.ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. CENTRE-TILT mechanism: The mechashould be m should be designed with the following features: • 360° revolving type.,• 17° ±2° maximum tilt on pivot at centre • Upright position locking.• Tilt tension adjustment. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSY: The bellow should be 3 piece telescopic type and injection moulded in Black Polypropylene. PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.)TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black nylon.Overall Dimensions of Chair Seat Height - min 43.3 to max 54.3cm. Height - min 89.5 to max 100.5cm. Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

Supply of Table Type-II (STYLO)Stylo table size shall be 1200 Width mm x 600 Depth mm x 750 Height mm . The table top shall be made of pre- laminated particle board with 18 mm thick and 15 mm thick understructure covered with PVC lipping. There is a Keyboard trolley attached to the desk by default. The locking provision is given only for the top drawer. It consists of total 3 drawers on one side and open stoarge space for CPU and any other documents given on right hand side. STYLO desk size : 1200W x 600D x 750H, in mm

Supply of Table Type-II (STYLO)Enzo Table - 5026 size shall be 1500 Width mm x 750 Depth mm x 750 Height mm . The table top shall be made of pre- laminated particle board with 18 mm thick and 15 mm thick understructure covered with PVC lipping .There shall be locking provided for top drawers only , attractive black colour handles for all drawers plus only one colour is available beech. It shall have one drawer (RHS ) & HDU attachment on one side & 3 drawer unit on the other side ( LHS of user ) .Enzo Table - 5026 size : 1500 W x 750 D x 750 H

Supply and fixing of European Water Closet of Ist quality with plastic seat and lid and low down flushing tank 10 Lit capacity confirming to IS:2556-Part-2-1973 of Hidustan/Neycer or Parry ware make white glazed with 'S' trap.

Supply and fixing of 110 mm dia (6kg/sqcm) PVC pipes including cost and conveyance of all materials all labour charges etc., complete.

Supply and fixing of 75 mm dia (6kg/sqcm) PVC pipes including cost and conveyance of all materials all labour charges etc., complete.

Supply and fixing Indian make Flat Back Wash Hand basin with pedestal (HSW/Parryware/Neycer) 1st quality conforming to IS:2556-Part-4:1972 with waste fittings like rubber plug, chain, 32mm nominal size C.P. Fitting with parallel pipe thread conforming to IS:2963-1979 and fitted with 15mm nominal bore chromium plated pillar tap of 1st quality Indian make 400 grams Seiko/Senior/Nice/Esso or equivalent complete with standard CI brackets : 550 x 400 mm - double C.P. Pillar cock.

Supply and Fixing of Premium make CPVC Pipes of 1" dia (28.60mm ODPipe - SDR 13.5) and Fittings to meet the requirement of ASTM-D 2846 having the same physical Properties for Hot and Cold Water (IS 15778:2007)

Supply and Fixing of Premium make CPVC Pipes of 1/2" dia (15.90mm OD Pipe - SDR 13.5) and Fittings to meet the requirement of ASTM-D 2846 having the same physical Properties for Hot and Cold Water (IS 15778:2007)

Supply and fixing CP Long body bib cock facy type deluxe heavy duty 12.7mm dia Indian make Seiko/Senior/Nice or equivalent

Supply and fixing CP Short body bib cock facy type deluxe heavy duty 12.7mm dia Indian make Seiko/Senior/Nice or equivalent

Supply and fixing PVC 1" gate valve including cost of PVC pipe, bends, couplings and Running Joints etc., complete.

Supply and fixing of Polyethylene water storage tank double layer conforming to IS:12701-1996 with lid.

Supplying and Fixing 76.2 mm Nahny Trap 1st quality in RCC floors

Supply and fixing of soap stands in the washroms including cost and conveyance of all materials, labour charges etc.,

Supply and fixing of 25.4 mm dia& 609.6 mm long aluminium anodized towel rod with brackets and aluminium screws including cost and conveyance of all materials, labour charges etc., complete

Supplying & Fixing white glazed flat back half stall urinals 1st quality conforming to IS:2556-1995 with standard C.P. Spreader of overall size 95 x 95 x 57 mm conforming to IS:2556-Part6, Sec-6-1974 fixed with screws complete Indian make (HSW/Parry/Neyce

Supply and Fixing of 25mm outer dia (1.6-1.8)mm thick rigid P.V.C. pipe (ISI MARK) of make Sudhakar /Macoplast/Modi with all required accessories like bends, junction box with cover etc., including all labour charges etc., complete.

Wiring with 2 runs of 14/0.3mm (1.0 Sq.mm) Fire Retardant (FR) P.V.C. insulated flexible copper cable (ISI MARK) in existing pipe with 6A modular switch, Ceiling rose and hot dip galvanized metal boxes with cover frame to switch control box including all labour charges etc., complete for light, bell, fan and exhaust fan points in Non-Residential Buildings (makes Anchor / Gold Medal / Million / Vimal / Maru / Milltec.)

Providing 6A modular switch with 3 No 3/2 pin socket, and hot dip galvanized metal boxes with modular cover frame to switch control box including all labour charges etc., complete in Non-Residential Buildings Legrand Arteor / Schneider Zen celo/ Crabtree Murano or Ducor /L&T-englaze/ GM-(Four-Five)/ Goldmedal(GIFA)

Supply and run of 4 of 36/0.3mm (2.5 Sq.mm) F.R P.V.C. insulated flexible copper cable in existing pipe for mains inlcuding all labour charges etc., complete.

Wiring with 4 runs of 56/0.3mm ( 4.0 Sq.mm) Fire retardant (FR) P.V.C. insulated flexible copper cable (ISI MARK) in existing metalic/ Non- metalic conduit pipe for run of mains including all labour charges etc.,from LDB at each floor to the Board.

Supply and fixing of 4way SPN Distribution Board with IP 43 protection concealed in wall including chisiling, masonry work & suitable for S.P. out going MCBs in sheet steel enclosure with 1no. 40A FP Isolator and 4 Nos 6-32A SP MCBs including (make ABB/Standard / Havells-euro II / C&S / L&T/GM /Gold Medal/Anchor/Salzer/Polycab ) complete for finished item of work as per directions of Eng-in-charge..

Providing independent earthing by excavating a trench to a depth of 2.1 M in all soils, as per size specified in the Data, using 40mm dia 'B' class GI pipe of 2.5 Mtrs length with necessary accessories with hume pipe ring duly providing staggered holes including filling with equal proportion of Salt and Charcoal in layers and all labour charges etc., complete for small quarters.

Supply and fixing of 20W,1900lumens T8,not less than 1100mmlength LED retrofit tube light withaluminium anodised body, inputvoltage AC 220 - 260 Volts withPF>0.9, Surge protection: 2KV,THD<10%, with inbuilt driver and frosted cover CCT: 3000K - 5700K,minimum CRI>70, .etc., complete as per IS 10322 (Part 5/ Sec 1)..2012 Makes : As per list of recommended brands as category II.

Supply and fixing 48" (1200mm) Sweep Ceiling Fan of makes (Crompton High speed/Bajaj Ultima/Havells Velocity/ Usha Astra/ Orient Summer Pride) with Modular Electronic Regulator of makes (Crab Tree/Feno Swtch/ Toyoma/Fortune Art/ Million / Gold Medal / Vimal / Anchor Roma)

Supply and fixing of (7 to 9)W LED Lamp with input voltage 90 to 300V, Color temperature 3000k - 6500k, Beam angle 170 - 220 degrees, B22 base.Makes: Phillips /Crompton / Bajaj / Havells / Halonix/ GM/ HPL Syska / Green Lites / Fortune Arrt / GoldMedal / Luker/ Leo/ Orbit /Rhino / GLO LED/ Million/ Victoria/ Benlo/ Goldwyn

Supply and fixing of 24W LED Slim Panel Round / Square suitable for Recessed / Surface mounting made of diecast alluminium body with powder coating, acrylic diffuser with Driver as per IS: 15885 (Part 2/ Sec 13) : 2012 , operating voltage range of 150 to 265 Volts AC, P.F > 0.9, Surge protection: 2KV,THD<10%, with high power LED's having acy of > 120 lumins/watt,CCT: 3000K - 5700K, minimum CRI>70, .etc., complete Makes : VIN/Surya / Fortune Art / Syska / GM / Green Lites / Gold Medal / C&S / Pharox / Anchor asonic / Stanjo/Ib LED/Promtec/Eveready/Enrich/Opple b) LED MAKE : CREE / NICHIA / OSRAM / SAMSUNG / EVERLIGHT/ San'an

Supply and fixing of one 6A modular switch control & two 6A 3/2 pin socket and one 16A modular switch control and one 16A 3/2 pin socket on white coloured modular box with cover frame on separate board including all labour charges etc., complete but exluding the cost of wire. (makes Crabtree/Feno Switch/Toyoma/Fortune art)

Supply of 25 Sqmm 3.5 Core XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I) Makes: RPG / Finolex / Finecab / Paragon / V-Guard / Fortune Art / Suncab / Orbit.

Supply and fixing of Porcelain Rewirable 100A Fuse Units with wooden board. Makes: C&S/Standard/HPL/ Sputnik / Million / Gold Medal / Benlo /Anchor including all labour charges etc., complete

Supply and fixing air exhaust fan of light duty metallic blades 300mm(12") 900 R.P.M with double ball bearing and wire guard etc., complete of makes Crompton/Bajaj Bahar WG/ Havells Ventil Air - DS / Orient hill air.

Supply, installation testing and commisioning of 4 pair 23AWG Cat6 UTP ,flexible , double ended patch cords 2m/7ft along with 2 nos of RJ 45 connectors with strain relief boots Compatible to T568A,T568Bspecifications including making connections to information outletsMakes: Systimax /AMP/ Panduit/ Siemond/ /Legrand

Supply,laying ,testing and commisioning of 4-pair, Cat6 Solid (Third party ETL Intertek tested 600 MHZ above) to support 1Gbps with Cross (+) filler pair seperator & PVC sheath 23 AWG, STP/UTP Cable , Meets or exceeds ANSI/TIA-568-C.2 and UL Listed &RoHS Compliant in the existing raceways /pvc conduits including making connections to information outlets and patch panels with ferruling at both ends for identifiation with necessary tools for punching stripping crimping and testing required etc., completeMakes: Systimax /AMP/ Panduit/ Siemond/ Molex/Legrand

Supply , Installation, Testing and Comissioning of 9U(44mm)Wall mounted Communication rack in two sections viz rear wall mount Section and hinged front section with glass doors, swing handles ,lock , Top and Bottom Cable entries,Supports for mounting rack on wall , Cable managers, Fan tray with 2 x 230 Volt fans, Equipment mounting hardware, wire managers , power supply box for supplying power to hubs, fans etc along with earth continuity kit, Mcb, indicator, moulded power supply cable, Blank panels , sliding shelves etc. along with Power SpikeMake: APW/HCL/Valrack/Netrack

Supply and fixing of 1.8/1.9/2.0TR, 5 Star capable of delivering not less than 21600 BTU/hr and above with operating on refrigerant R-410A / R-32 Makes: As per list of recommended brands as category II. INVERTER Model Cool type split AC unit with high wall mounted Single Split indoor unit and outdoor condensing unit Hermetically sealed compressor suitable for operation on 230V, 50Hz, 1Phase AC supply capable of performing Heat cool dehumidifying air circulating and filtering with cooling and condensing units with 3 mts of copper piping, insulation kit and 4 mts of 4 core copper flexible chord with cordless remote control etc., dual barrier coating in order to protect coil form oxidation. Makes: Blue star / Hitachi / Daikin/Lloyd (prevailing models in the market)

Supply, Fabrication of 1set MS bracket suitable for fixing outdoor unit of split AC unit.

Supply and installation of 5.0KVA Stabilizer of Makes: V-Guard / Real Guard / Uni Stab / ITL.

Supply installation Testing and commissioning of 20.0 KVA 312/360 V DC on line UPS system as per IEC 62040-I (Safety), IEC 62040-3 (Performance) for critical IT solutions, fully digital IGBT Converter and Inverter, SCR rectifier with Internal /External isolation transformer from DC to AC, PWM, pure sine wave output, double conversion, output pf 0.8, with paralleling facility, standard communication features/options auto and manual static by pass switch three phase input / Three phase output. acoustic level shall be less than 58dB at 1 mtr distance.Makes: As per list of recommended brands.Makes: Numeric/APC/Fuji Electric / Sakshham /Emerson

Supply and fixing of 10 passenger lift (680 Kg's) Kone make with speed 1 m/sec, with micro processor based VVVF drive with front entrance no of floors served Ground + 3 floors(4 stops & 4 openings), with a travel of 9.9 meters Approx, with car inside size 1300 mm Wide X1350 mm DeepX 2200 mm height , car clear opening 800 mm Wide X 2000mm Height with main power supply- 400/440V 3 phase 50 Hz for auxiliaries, car enclosure( Stainless steel and panels stainless steel -304 , ceiling stainless steel -304) center opening doors, with Micro Processor based Down collective simplex with electro mechanical door lock with seven segment digital display. The lift is provided with following features Battery operated emergency light and alarm bell, call register signal and Vf door operator, Landing push button in landing door frames, Automatic rescue device, Stainless steel button with SS cover, Digital position Indicator in car and landings, False ceiling in Car, Infra red door screen, Overload warning Indicator, SS hand rail on rear side etc., as approved by Eng-in-charge including cost and conveyance of all materials, labour charges, leads and lifts and finishing for finished item of work as directed by Engineer-in-charge

Supply of Visitor Chair (OXBO)SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D). BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. BACK SIZE : 46.5 cm. (W) x 60.5cm. (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. TUBULAR FRAME: The powder coated (DFT 40-60.microns) tubular frame should be cantilever type & made of Ø2.54 ±0.03cm. x0.2 ±0.016cm thick M.S.E.R.W. Tube. Overall Dimensions of Chair Seat Height - 46.5cm. Height - 93.5cm.Width & Depth of Chair as measured from pedestal - Width-61.0 cm and Depth-64.5 cm.

Hire charges of Shovel-0.50 cum- 75 hp(JCB) including fuel & crew charges for clearing of the heavy jungle and levelling the out side yard of the Sub-station premises as per the directions of the Engineer-at - site.

Dismantling of Brick masonry or R.R. Masonry in Cement mortar and transporting the debris to dumping yard as directed by the engineer at site including conveyance and labour charges etc, complete.

Dismantling of doors, windows (wood) with shutters, complete and and carefully stacking them useful for reuse within 100 metre lead .

Cost of Dismantled doors and Windows with frames including all materials, all labour charges etc. complete (the cost towards dismantled doors and Windows will be recovered at the local market rate).

Earth work excavation in ordinary soils by manual means upto 3m depth for foundations and depositing on bank for all lifts and with an initial lead of 10m including all operational, incidental, labour charges such as shoring ,sheeting, planking, strutting, etc. complete for finished item of work including seigniorage excluding dewatering charges etc as per SS - 20 B (APSS 308).

Filling with useful available excavated earth (excluding rock) in trenches, sides of foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T & P etc., complete for finished item of work. (APSS NO. 309 & 310)

Filling with sand in foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T & P etc., complete for finished item of work. (APSS NO. 309 & 310)

Plain Cement concrete (1:4:8) using 40 mm metal with concrete mixer including cost and conveyance of all materials and all labour charges complete.

Supplying, cutting and placing HYSD bar reinforcement as per drawings and technical specifications for Bars below 36 mm dia including over laps and wastage, where they are not welded including cost and conveyance of all materials to site and all labour charges complete.

Providing Pre construction Anti termite is a process in which 1. chemical toxic to subterranean termites is apply/ inject into soil during early stage of building Construction 2. Treatement of soil Beneath the building and around the foundations conduct and chemical use as per BIS - IS 6313 (Part -2) 2013 code specification & CIB RC registered termiticide which creates a continuous chemical barrier beneath the building which kills or repels terminates & impervious to tremite entryImidacloprid 30.5% SC (IS 63131) dissolve 2.1 Ml/1 liter of water and apply emulsion/solution @ 7.5 Litres/Square meter (Sqm) of internal, external vertical surface of the colums , plinth beams (Back filling) walls and floor junction, external perimeters, along reatining wall @ 5.0 Liters/Sqm of the horizontal surface of basement top surface of the basement filling below flooring bed (Plinth) & @ 2.0 Litres/ Line meter at expansion joints. The substructure of a depth of 500mm around coulmns & 300mm deep around plinth beams, basements & floor filling area including excavation channel along the wall & rodding etc. cost & Conveyance of all materials to the site, cost of labour for sparying, rodding etc. complete for furnished item of work as per the approval of the Engineer-in-charge

Brick Masonry in CM (1:5) with Fly ash cement/lime solid blocks with compressive strength of 75 kg/sq.cm - IS:12894-1990 - CLASS - 7.5 - 290 x 200 x 140 mm including seignorage charges including cost and conveyance of all materials to site and all labour charges complete.

Augoring and boring of 375mm dia holes in site Bored cast-in-situ R.C.C. Piles with R.C.C. M-20, Nominal Mix (1:1.5:3) using 20mm size aggregate for building foundations in loamy, clayey soils like Black cotton soils and ordinary soils as per IS 2911 - 1980 and as per approved designs including cost and conveyance of all materials to site excluding cost of steel and including all operations, incidental, labour charges, hire charges of machinery, augor bore drill and shell equipment, etc, complete for all depths and for finished item of work.

Under reaming for Bored cast-in-situ R.C.C. Piles of 375mm dia with R.C.C. M-20, Nominal Mix (1:1.5:3) using 20mm size aggregate for building foundations in loamy, clayey soils like Black cotton soils and ordinary soils as per IS 2911 - 1980 and as per approved designs including cost and conveyance of all materials to site excluding cost of steel including all operations, incidental, labour charges, hire charges of machinery, augur bore drill and shell equipment, etc, complete for all depths and for finished item of work.

Augoring and boring of 300mm dia holes in site Bored cast-in-situ R.C.C. Piles with R.C.C. M-20, Nominal Mix (1:1.5:3) using 20mm size aggregate for building foundations in loamy, clayey soils like Black cotton soils and ordinary soils as per IS 2911 - 1980 and as per approved designs including cost and conveyance of all materials to site excluding cost of steel and including all operations, incidental, labour charges, hire charges of machinery, augor bore drill and shell equipment, etc, complete for all depths and for finished item of work.

Under reaming for Bored cast-in-situ R.C.C. Piles of 300mm dia with R.C.C. M-20, Nominal Mix (1:1.5:3) using 20mm size aggregate for building foundations in loamy, clayey soils like Black cotton soils and ordinary soils as per IS 2911 - 1980 and as per approved designs including cost and conveyance of all materials to site excluding cost of steel including all operations, incidental, labour charges, hire charges of machinery, augur bore drill and shell equipment, etc, complete for all depths and for finished item of work .

VRCC M- 25 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. PILE CAPS

VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. PLINTH BEAM

CELLAR FLOOR - LINTEL BEAMS VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

FIRST FLOOR LINTEL BEAMS VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

SECOND FLOOR LINTEL BEAMS VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

THIRD FLOOR LINTEL BEAMS VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

CELLAR FLOOR - COLUMNS VRCC M- 25 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

FIRST FLOOR COLUMNS VRCC M- 25 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

SECOND FLOOR COLUMNS VRCC M- 25 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

THIRD FLOOR COLUMNS VRCC M- 25 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

CELLAR FLOOR - SUNSHADES/CHAJJAS VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

FIRST FLOOR SUNSHADES/CHAJJAS VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

SECOND FLOOR SUNSHADES/CHAJJAS VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

THIRD FLOOR SUNSHADES/CHAJJAS VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

CELLAR FLOOR - ROOF BEAMS VRCC M- 25 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

FIRST FLOOR ROOF BEAMS VRCC M- 25 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

SECOND FLOOR ROOF BEAMS VRCC M- 25 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

THIRD FLOOR ROOF BEAMS VRCC M- 25 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

CELLAR FLOOR ROOF SLAB VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

FIRST FLOOR ROOF SLAB VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

SECOND FLOOR ROOF SLAB VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

THIRD FLOOR ROOF SLAB VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

Providing impervious coat to exposed RCC roof slab surface with CM(1:3), 20mm thick with 1kg of water proof compound per bag of cement laid over roof when it is green including cost of all materials, seigniorage charges, conveyance charges of materials and including all operational, incidental and labour charges for mixing mortar, laying, rendering smooth and thread lining, curing, rounding off junctions of wall and slab etc,, complete for finished item of work

CELLAR FLOOR Brick Masonry in CM (1:6) with 2nd class Bricks traditional size 23 x 11 x 7 cms including cost and conveyance of all materials to site and all labour charges complete.

FIRST FLOOR Brick Masonry in CM (1:6) with 2nd class Bricks traditional size 23 x 11 x 7 cms including cost and conveyance of all materials to site and all labour charges complete.

SECOND FLOOR Brick Masonry in CM (1:6) with 2nd class Bricks traditional size 23 x 11 x 7 cms including cost and conveyance of all materials to site and all labour charges complete.

THIRD FLOOR Brick Masonry in CM (1:6) with 2nd class Bricks traditional size 23 x 11 x 7 cms including cost and conveyance of all materials to site and all labour charges complete.

CELLAR FLOOR 11.5 cm wide Brick masonry for super-structure on ground floor in cm (1:4) using second class traditional size bricks including cost of all materials and it's conveyance, labour and all operations for constructing half brick masonry, mixing cement mortar, curing etc.,complete.

FIRST FLOOR 11.5 cm wide Brick masonry for super-structure on ground floor in cm (1:4) using second class traditional size bricks including cost of all materials and it's conveyance, labour and all operations for constructing half brick masonry, mixing cement mortar, curing etc.,complete.

SECOND FLOOR 11.5 cm wide Brick masonry for super-structure on ground floor in cm (1:4) using second class traditional size bricks including cost of all materials and it's conveyance, labour and all operations for constructing half brick masonry, mixing cement mortar, curing etc.,complete.

CELLAR FLOOR Plastering with CM (1:3), 12 mm thick in one coat for inernal faces of ceilings etc.,including cost and conveyance of all materials all labour charges etc, complete.

FIRST FLOOR Plastering with CM (1:3), 12 mm thick in one coat for inernal faces of ceilings etc.,including cost and conveyance of all materials all labour charges etc, complete.

SECOND FLOOR Plastering with CM (1:3), 12 mm thick in one coat for inernal faces of ceilings etc.,including cost and conveyance of all materials all labour charges etc, complete.

THIRD FLOOR Plastering with CM (1:3), 12 mm thick in one coat for inernal faces of ceilings etc.,including cost and conveyance of all materials all labour charges etc, complete.

CELLAR FLOOR Plastering with CM (1:5), 12 mm thick in one coat for inernal faces of walls, ,including cost and conveyance of all materials all labour charges etc, complete.

FIRST FLOOR Plastering with CM (1:5), 12 mm thick in one coat for inernal faces of walls, ,including cost and conveyance of all materials all labour charges etc, complete.

SECOND FLOOR Plastering with CM (1:5), 12 mm thick in one coat for inernal faces of walls, ,including cost and conveyance of all materials all labour charges etc, complete.

THIRD FLOOR Plastering with CM (1:5), 12 mm thick in one coat for inernal faces of walls, ,including cost and conveyance of all materials all labour charges etc, complete.

CELLAR FLOOR Plastering with CM (1:5), 20 mm thick in one coat for external faces of walls including cost and conveyance of all materials all labour charges etc, complete.

FIRST FLOOR Plastering with CM (1:5), 20 mm thick in one coat for external faces of walls including cost and conveyance of all materials all labour charges etc, complete.

SECOND FLOOR Plastering with CM (1:5), 20 mm thick in one coat for external faces of walls including cost and conveyance of all materials all labour charges etc, complete.

THIRD FLOOR Plastering with CM (1:5), 20 mm thick in one coat for external faces of walls including cost and conveyance of all materials all labour charges etc, complete.

Laying P.C.C.(1:2:4) using 10 to 12 mm HBG metal including cost and conveyance of all materials to site and all labour charges complete for finished item of work.

Flooring with Supply of Double charged / multi charged stain free full body porcelain vitrified tiles with double layer pigment of Size 600 x 600 mm and thickness between 8-10 mm and 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs, Make: Somany,HR, Jhonson,Naveen Ceramics, Kajaria, Nitco, Sphinx, RAK or equivalent set over base coat of cement mortar (1:8), 12 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3.kgs per sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, sand water and tiles etc., complete, for finished item of work including the cost of conveyance of all materials.

Flooring with 8mm thick Non-skid edge cut rectified ceramic tiles Ist quality , set over base coat of cement mortar (1:8), 12 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3kgs per sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, sand water and tiles etc., complete, including seigniorage charges, etc., complete for finished item of work, including the cost of conveyance of all materials.

CELLAR FLOOR Providing and applying synthetic plaster putty or plaster of paris putty or lime punning of average 1 to 2mm thickness over plastered surface to prepare the surface even and smooth after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, sand the surface, clean & wipe off loose dust, applying knifing paste filler by putty knife/muslin pad, air dry for 2-3hrs, sand with 180 and 320 No., emery paper for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work for internal walls.

FIRST FLOOR Providing and applying synthetic plaster putty or plaster of paris putty or lime punning of average 1 to 2mm thickness over plastered surface to prepare the surface even and smooth after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, sand the surface, clean & wipe off loose dust, applying knifing paste filler by putty knife/muslin pad, air dry for 2-3hrs, sand with 180 and 320 No., emery paper for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work for internal walls.

SECOND FLOOR Providing and applying synthetic plaster putty or plaster of paris putty or lime punning of average 1 to 2mm thickness over plastered surface to prepare the surface even and smooth after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, sand the surface, clean & wipe off loose dust, applying knifing paste filler by putty knife/muslin pad, air dry for 2-3hrs, sand with 180 and 320 No., emery paper for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work for internal walls.

CELLAR FLOOR Painting with acrylic EXTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre exterior grade of approved brand and colour/shade two coats over a base coat of appropriate primer (grade-II) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work.

FIRST FLOOR Painting with acrylic EXTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre exterior grade of approved brand and colour/shade two coats over a base coat of appropriate primer (grade-II) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work.

SECOND FLOOR Painting with acrylic EXTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre exterior grade of approved brand and colour/shade two coats over a base coat of appropriate primer (grade-II) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work.

THIRD FLOOR Painting with acrylic EXTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre exterior grade of approved brand and colour/shade two coats over a base coat of appropriate primer (grade-II) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work.

CELLAR FLOOR Painting with synthetic polymer plastic INTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and shade two coats over a base coat of appropriate interior primer(grade-I) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work.

FIRST FLOOR Painting with synthetic polymer plastic INTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and shade two coats over a base coat of appropriate interior primer(grade-I) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work.

SECOND FLOOR Painting with synthetic polymer plastic INTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and shade two coats over a base coat of appropriate interior primer(grade-I) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work.

THIRD FLOOR Painting with synthetic polymer plastic INTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and shade two coats over a base coat of appropriate interior primer(grade-I) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work.

Providing R.C.C. plates of 38mm thick with R.C.C.(1:1.5:3) (including cost of steel reinforcement ) and plastering with CM(1:5),12mm thick including cost and conveyance of all materials to site and all labour charges complete.

Providing of RCM facia or drop wall 5cm thick in CM (1:3) including seignorage charges with rabbit wire mesh (chicken mesh) of not less than 30gauge & nominal reinforcement as directed by Engineer-in-charge with dubara sponge finishing, including cost & conveyance of all materials to site, scaffolding charges and all labour charges complete.

Providing and fixing factory made UPVCwhite colour sliding glazedwindow upto1.50m in height dimension comprising of uPVC multi chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60±0.2mm thick galvanized mild steel section made from roll forming process of required length (shape & sizeaccording to uPVCprofile), appropriate dimension of UPVC extruded glazing beads and UPVC extruded interlocks, EPDMgasket, woolpile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be40kg), G.Ifasteners 100x8mm size for fixing frame to finished wall and necessary stainless steel screwsetc. Profile offrame & sash shall be mitred cut andfusion welded at all corners, including drilling of holes for fixing hardware's and drainage of wateretc. After fixing frame the gap between frame and adjacent finished walls all be filled with weather proof silicon sealent over backer rod of required size and ofapproved quality, all complete as per approved drawing & direction of Engineer -in - Charge inclusive of cost of Single/double glasspanes, wiremesh and silicon sealent .Note: For uPVC frame and sash extruded profiles minus 5%tolerancein dimension i.e. in depth &width of profile shall be acceptable.Variation in profile dimension in higher side shall be accepted but no extra payment onthis account shallbemade.Two track two panels sliding window made of (big series)frame 67 x 50 mm & sash 46 x 62 mmboth having wallthickness of 2.3 ± 0.2 mm and singleglazing bead / doubleglazing bead of appropriate dimension .(Area of window upto 1.75 sqm ).

Supply and fixing of M.S. grill to Ground floor windows with 10mm square solid rods with 25mm x 25mm x 5mm L Angle and approved design given by the department and as directed by the engineer at site including cost and conveyance of all materials and all labour charges etc., complete. (1.22X1.22 )

Flush door: supply and fixing of 35 mm thick flush door single shutter, solid bond wood block board type with teak veneer on both faces including 5mm thick glass and supplying positioning and fixing door frame with well seasoned assam teak/beeja sal/sal wood scantlings of size 100 mm x 75 mm, including 6 nos. Of ms 'z' hold fasts of size 250x50x8 mm,including aluminium 3 nos. Of 125 mm butt hinges, 1 no. Door stoper, 2 no. 100 mm long door handles , 1 no. Aldrop of size 250 mm long , 1 nos. Of 200 mm long tower bolts, with bolts, nuts, nf screws including cost and conveyance of all materials to site, labour charges etc., including minor extra fixtures required if any as directed by the engineer-in-chrge of the work complete for finished item of work

Supply and fixing of CEMENT BONDED PRE-LAMINATED PARTICLE BOARDS aluminum glazed partitions using 10 MM CEMENT BONDED PRE-LAMINATED PARTICLE BOARDS and 5.00 mm thick plain glass to full height. Using with LAM to a height of 0.91 meter at bottom panel and remaining height with glass and aluminum sections anodized to 12 to 15 microns and of sections of size 37mm x 62mm and 1.5mm thickness with one meter centre to centre duly fixed with clip beading on both sides including fixing the frame to pillars by M.S. flats, bolts and nuts including cost and conveyance of all materials etc., complete as directed during execution.

Supply and fixing Aluminium Single Shutter door partly Glazed &Panneled with aluminium anodised sections of Jindal sections Shutter frame top of size 44.45 mm x 47.62 mm x 1.95 section 19571 , bottom of size 44.45 mm x 114.30 mm x 2.15 section 19574 and verticals of 19569 of size 44.45 mm x 47.62 mm x 2.02 and fitted with 10mm thick both sides prelaminated cement particle board and 5mm thick plain glass for shutter and other acccessories like supply and fixing aluminium handles, door stoppers, latches, etc., for each shutter, and all labour charges for fixing the fixtures with required no.of screws, bolts and nuts and including labour charges for fixing the frame in position, fixing shutter to frame etc. completed for finished item of work

Providing and fixing Aluminium Extruded Section Body Tubular Type Hydraulic Door Closer (IS: 3564) with double speed adjustment with necessary accessories and screws etc. complete (Type-3: for width of doors 851 to 1000 mm)

Providing and fixing of Wood Polymer Composite (WPC) solid doors with frame. Door shutter consists of Wood Polymer Composite (WPC) solid, frosty white single extruded factory made in 18 MM thickness (Density 650 kg/Cum, Weight 35Kg) and Door Frame consists of solid Wood Polymer Composite (WPC) single extruded section of size with encapsulation of 8MM rigid layer on all the six surfaces. The door frame will have a rebat of 32MM. Door Frame section of 45x75 MM . The two Vertical members are to be joined together with the horizontal member using 8x50 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member and with fixtures 1no aluminium aldrop 200mm lond and 2nos tower bolt 150mm long, the rate is inclusive of cost and conveyance of all materials to site and all labour charges complete.

Supplying and fixing Gyp Board Suspended regular single layer false ceiling (GS-MFSC-4.1 as per India Gypsum) using 12.5 mm thick Gyp Board conforming to IS 2095 - 1982 fixing to Gyp steel GI perimeter channels of size 20 mm x 27 mm x 30 mm(web) of 0.55 mm thick along the perimeter of ceiling screw fixed to brick work/ partition at 610 mm c/c and suspending the frame work using Intermediate channels (45 mm x 15mm x 15mm x 0.9 mm) from soffit at 1220 mm c/c with ceiling angle (25 mm x 10 mm x 0.55 mm) fixed with GI Cleat and steel expansion fasteners & connecting clip to the ceiling channels (with knurled web of 51.5 mm x 26 mm x 10.5 mm x 0.55 mm) fixed in direction perpendicular to the intermediate channel at 457 mm c/c and fixing the 12.5 mm tapered edge Gypboard with 25 mm drywall screws at 230 mm c/c & jointing and finishing using joint compound and paper tape to have a flush look including filling the tapered & square edges with jointing compound, two coats of drywall topcoat complete for finished item of work as per India Gypsum Ltd specification.

Supplying & fixing collapsible steel shutters with vertical, double channel of 20 x10x2 mm of 100 mm centre, Bracers with flat iron 40x40x6 mm with 38 mm dia steel pulleys, the top, bottom and side vertical frames of the collapsible gate with 65x65mmx8mm MS Angle and middle guide rail at site height with 65mmx8mm MS flat for the pulleys to guide and fixed with locking arrangements, stoppers, handles, all accessories all fixtures and painted with one coat of approved steel primer etc., complete for finished item of work.

Supply, fabrication and fixing of stainless steel railing of approved design with Stainless Steel Tubes, sections, plates, sheets & pipes of all sizes & diameters for grade -304 including all accessories and all labour charges complete for finished item of work.

Vibrated Plain Cement concrete (1:2:4) using 20mm size HBG metal with concrete mixer including cost and conveyance of all materials and all labour charges complete.

Supply and fixing( Positioning) modular panel based 4 units work station of size 4’x 4' x4’ double skinned partition of 62 mm (+/-5%) thick made out of extrude Aluminium sections powder coated with 12mm thick pre-laminated particle board panels/soft board / marker board panels, all the exposed metal surfaces of supports, top covers and hardware for fixing furniture to partition is to be powder coated with approved colour/Shade of 50 micron thick and provision for built in cable management provided with 2 No integrated wire ways of 130mm high, provided one each at skirting level and other at just below / above the work top (table ) level. The minimum free space required in the wire ways to accommodate power, data and communication cables is to be 30mmx120mm with injection moulded ABS end caps and with side partitions for every work station and with the front walls below the table top only (Switches and sockets of RAW power/ UPS /Data /Telephone shall be recessed).Provision should be made for three 5 amp socktes (one with switch control) and telephone jack, just below/above table top and one 5amp switch and one number RJ 15 and one No RJ 45 socket for LAN point below table top. The table top with PLB 25mm thick post formed particle board and the surface top with all exposed edges duly edge banded. The pin board is made of 12 mm thick soft board covered with approved colour/ shade /design/ texture fabric. The partition is to be provided with leveling bolts to account for any unevenness in the floor. The work station provided with table top of width of 500 mm and height of table top is 750 mm from the floor level. Key board tray with high impact plastic and C P U stand/ trolley and PLB 3 draw pedestal unit of size 450 x 500 x 650 mm as per approved design, make and accessiores and as per drawing and directions of Eng-in- charge .

Supply of Storwel plain shall have an overall size of 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The Storwel Plain should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.Overall Dimensions of Storwel= 916mm(W)x486mm(D)x1981mm(H) shelf thickness- 0.7mm Back thickness - 0.8mm, Door thickness- 0.8mm.

Supply of Slotted Angle Rack of Size: L 900 x D 450x H 1800 4 shelves including top & bottomHaving 2 stiffener in each side. Angles : 40mm x 40mm x 2mm(Thick)., Shelf : 1mm CRCA sheet

Supply of Chair Type-I Mid back (OXBO) with SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam.SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D).BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn.BACK SIZE : 46.5 cm (W) x 70.5 cm (H).HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. CENTRE-TILT mechanism: The mechashould be m should be designed with the following features:• 360° revolving type, • 17° ±2° maximum tilt on pivot at centre,• Upright position locking. Tilt tension adjustment. .PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSY: The bellow should be 3 piece telescopic type and injection moulded in Black Polypropylene. PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.)TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black nylon.Overall Dimensions of Chair Seat Height - min 43.3 to max 54.3cm.Height - min 99.5 to max 110.5cm.Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm

Supply of Chair Type-II Low back (OXBO)SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D).BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn.BACK SIZE : 46.5 cm (W) x 60.5 cm (H). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression.ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. CENTRE-TILT mechanism: The mechashould be m should be designed with the following features: • 360° revolving type.,• 17° ±2° maximum tilt on pivot at centre • Upright position locking.• Tilt tension adjustment. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSY: The bellow should be 3 piece telescopic type and injection moulded in Black Polypropylene. PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.)TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black nylon.Overall Dimensions of Chair Seat Height - min 43.3 to max 54.3cm. Height - min 89.5 to max 100.5cm. Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

Supply of Table Type-II (STYLO)Stylo table size shall be 1200 Width mm x 600 Depth mm x 750 Height mm . The table top shall be made of pre- laminated particle board with 18 mm thick and 15 mm thick understructure covered with PVC lipping. There is a Keyboard trolley attached to the desk by default. The locking provision is given only for the top drawer. It consists of total 3 drawers on one side and open stoarge space for CPU and any other documents given on right hand side. STYLO desk size : 1200W x 600D x 750H, in mm

Supply of Table Type-II (STYLO)Enzo Table - 5026 size shall be 1500 Width mm x 750 Depth mm x 750 Height mm . The table top shall be made of pre- laminated particle board with 18 mm thick and 15 mm thick understructure covered with PVC lipping .There shall be locking provided for top drawers only , attractive black colour handles for all drawers plus only one colour is available beech. It shall have one drawer (RHS ) & HDU attachment on one side & 3 drawer unit on the other side ( LHS of user ) .Enzo Table - 5026 size : 1500 W x 750 D x 750 H

Supply and fixing of European Water Closet of Ist quality with plastic seat and lid and low down flushing tank 10 Lit capacity confirming to IS:2556-Part-2-1973 of Hidustan/Neycer or Parry ware make white glazed with 'S' trap.

Supply and fixing of 110 mm dia (6kg/sqcm) PVC pipes including cost and conveyance of all materials all labour charges etc., complete.

Supply and fixing of 75 mm dia (6kg/sqcm) PVC pipes including cost and conveyance of all materials all labour charges etc., complete.

Supply and fixing Indian make Flat Back Wash Hand basin with pedestal (HSW/Parryware/Neycer) 1st quality conforming to IS:2556-Part-4:1972 with waste fittings like rubber plug, chain, 32mm nominal size C.P. Fitting with parallel pipe thread conforming to IS:2963-1979 and fitted with 15mm nominal bore chromium plated pillar tap of 1st quality Indian make 400 grams Seiko/Senior/Nice/Esso or equivalent complete with standard CI brackets : 550 x 400 mm - double C.P. Pillar cock.

Supply and Fixing of Premium make CPVC Pipes of 1" dia (28.60mm ODPipe - SDR 13.5) and Fittings to meet the requirement of ASTM-D 2846 having the same physical Properties for Hot and Cold Water (IS 15778:2007)

Supply and Fixing of Premium make CPVC Pipes of 1/2" dia (15.90mm OD Pipe - SDR 13.5) and Fittings to meet the requirement of ASTM-D 2846 having the same physical Properties for Hot and Cold Water (IS 15778:2007)

Supply and fixing CP Long body bib cock facy type deluxe heavy duty 12.7mm dia Indian make Seiko/Senior/Nice or equivalent

Supply and fixing CP Short body bib cock facy type deluxe heavy duty 12.7mm dia Indian make Seiko/Senior/Nice or equivalent

Supply and fixing PVC 1" gate valve including cost of PVC pipe, bends, couplings and Running Joints etc., complete.

Supply and fixing of Polyethylene water storage tank double layer conforming to IS:12701-1996 with lid.

Supplying and Fixing 76.2 mm Nahny Trap 1st quality in RCC floors

Supply and fixing of soap stands in the washroms including cost and conveyance of all materials, labour charges etc.,

Supply and fixing of 25.4 mm dia& 609.6 mm long aluminium anodized towel rod with brackets and aluminium screws including cost and conveyance of all materials, labour charges etc., complete

Supplying & Fixing white glazed flat back half stall urinals 1st quality conforming to IS:2556-1995 with standard C.P. Spreader of overall size 95 x 95 x 57 mm conforming to IS:2556-Part6, Sec-6-1974 fixed with screws complete Indian make (HSW/Parry/Neyce

Supply and Fixing of 25mm outer dia (1.6-1.8)mm thick rigid P.V.C. pipe (ISI MARK) of make Sudhakar /Macoplast/Modi with all required accessories like bends, junction box with cover etc., including all labour charges etc., complete.

Wiring with 2 runs of 14/0.3mm (1.0 Sq.mm) Fire Retardant (FR) P.V.C. insulated flexible copper cable (ISI MARK) in existing pipe with 6A modular switch, Ceiling rose and hot dip galvanized metal boxes with cover frame to switch control box including all labour charges etc., complete for light, bell, fan and exhaust fan points in Non-Residential Buildings (makes Anchor / Gold Medal / Million / Vimal / Maru / Milltec.)

Providing 6A modular switch with 3 No 3/2 pin socket, and hot dip galvanized metal boxes with modular cover frame to switch control box including all labour charges etc., complete in Non-Residential Buildings Legrand Arteor / Schneider Zen celo/ Crabtree Murano or Ducor /L&T-englaze/ GM-(Four-Five)/ Goldmedal(GIFA)

Supply and run of 4 of 36/0.3mm (2.5 Sq.mm) F.R P.V.C. insulated flexible copper cable in existing pipe for mains inlcuding all labour charges etc., complete.

Wiring with 4 runs of 56/0.3mm ( 4.0 Sq.mm) Fire retardant (FR) P.V.C. insulated flexible copper cable (ISI MARK) in existing metalic/ Non- metalic conduit pipe for run of mains including all labour charges etc.,from LDB at each floor to the Board.

Supply and fixing of 4way SPN Distribution Board with IP 43 protection concealed in wall including chisiling, masonry work & suitable for S.P. out going MCBs in sheet steel enclosure with 1no. 40A FP Isolator and 4 Nos 6-32A SP MCBs including (make ABB/Standard / Havells-euro II / C&S / L&T/GM /Gold Medal/Anchor/Salzer/Polycab ) complete for finished item of work as per directions of Eng-in-charge..

Providing independent earthing by excavating a trench to a depth of 2.1 M in all soils, as per size specified in the Data, using 40mm dia 'B' class GI pipe of 2.5 Mtrs length with necessary accessories with hume pipe ring duly providing staggered holes including filling with equal proportion of Salt and Charcoal in layers and all labour charges etc., complete for small quarters.

Supply and fixing of 20W,1900lumens T8,not less than 1100mmlength LED retrofit tube light withaluminium anodised body, inputvoltage AC 220 - 260 Volts withPF>0.9, Surge protection: 2KV,THD<10%, with inbuilt driver and frosted cover CCT: 3000K - 5700K,minimum CRI>70, .etc., complete as per IS 10322 (Part 5/ Sec 1)..2012 Makes : As per list of recommended brands as category II.

Supply and fixing 48" (1200mm) Sweep Ceiling Fan of makes (Crompton High speed/Bajaj Ultima/Havells Velocity/ Usha Astra/ Orient Summer Pride) with Modular Electronic Regulator of makes (Crab Tree/Feno Swtch/ Toyoma/Fortune Art/ Million / Gold Medal / Vimal / Anchor Roma)

Supply and fixing of (7 to 9)W LED Lamp with input voltage 90 to 300V, Color temperature 3000k - 6500k, Beam angle 170 - 220 degrees, B22 base.Makes: Phillips /Crompton / Bajaj / Havells / Halonix/ GM/ HPL Syska / Green Lites / Fortune Arrt / GoldMedal / Luker/ Leo/ Orbit /Rhino / GLO LED/ Million/ Victoria/ Benlo/ Goldwyn

Supply and fixing of 24W LED Slim Panel Round / Square suitable for Recessed / Surface mounting made of diecast alluminium body with powder coating, acrylic diffuser with Driver as per IS: 15885 (Part 2/ Sec 13) : 2012 , operating voltage range of 150 to 265 Volts AC, P.F > 0.9, Surge protection: 2KV,THD<10%, with high power LED's having acy of > 120 lumins/watt,CCT: 3000K - 5700K, minimum CRI>70, .etc., complete Makes : VIN/Surya / Fortune Art / Syska / GM / Green Lites / Gold Medal / C&S / Pharox / Anchor asonic / Stanjo/Ib LED/Promtec/Eveready/Enrich/Opple b) LED MAKE : CREE / NICHIA / OSRAM / SAMSUNG / EVERLIGHT/ San'an

Supply and fixing of one 6A modular switch control & two 6A 3/2 pin socket and one 16A modular switch control and one 16A 3/2 pin socket on white coloured modular box with cover frame on separate board including all labour charges etc., complete but exluding the cost of wire. (makes Crabtree/Feno Switch/Toyoma/Fortune art)

Supply of 25 Sqmm 3.5 Core XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I) Makes: RPG / Finolex / Finecab / Paragon / V-Guard / Fortune Art / Suncab / Orbit.

Supply and fixing of Porcelain Rewirable 100A Fuse Units with wooden board. Makes: C&S/Standard/HPL/ Sputnik / Million / Gold Medal / Benlo /Anchor including all labour charges etc., complete

Supply and fixing air exhaust fan of light duty metallic blades 300mm(12") 900 R.P.M with double ball bearing and wire guard etc., complete of makes Crompton/Bajaj Bahar WG/ Havells Ventil Air - DS / Orient hill air.

Supply, installation testing and commisioning of 4 pair 23AWG Cat6 UTP ,flexible , double ended patch cords 2m/7ft along with 2 nos of RJ 45 connectors with strain relief boots Compatible to T568A,T568Bspecifications including making connections to information outletsMakes: Systimax /AMP/ Panduit/ Siemond/ /Legrand

Supply,laying ,testing and commisioning of 4-pair, Cat6 Solid (Third party ETL Intertek tested 600 MHZ above) to support 1Gbps with Cross (+) filler pair seperator & PVC sheath 23 AWG, STP/UTP Cable , Meets or exceeds ANSI/TIA-568-C.2 and UL Listed &RoHS Compliant in the existing raceways /pvc conduits including making connections to information outlets and patch panels with ferruling at both ends for identifiation with necessary tools for punching stripping crimping and testing required etc., completeMakes: Systimax /AMP/ Panduit/ Siemond/ Molex/Legrand

Supply , Installation, Testing and Comissioning of 9U(44mm)Wall mounted Communication rack in two sections viz rear wall mount Section and hinged front section with glass doors, swing handles ,lock , Top and Bottom Cable entries,Supports for mounting rack on wall , Cable managers, Fan tray with 2 x 230 Volt fans, Equipment mounting hardware, wire managers , power supply box for supplying power to hubs, fans etc along with earth continuity kit, Mcb, indicator, moulded power supply cable, Blank panels , sliding shelves etc. along with Power SpikeMake: APW/HCL/Valrack/Netrack

Supply and fixing of 1.8/1.9/2.0TR, 5 Star capable of delivering not less than 21600 BTU/hr and above with operating on refrigerant R-410A / R-32 Makes: As per list of recommended brands as category II. INVERTER Model Cool type split AC unit with high wall mounted Single Split indoor unit and outdoor condensing unit Hermetically sealed compressor suitable for operation on 230V, 50Hz, 1Phase AC supply capable of performing Heat cool dehumidifying air circulating and filtering with cooling and condensing units with 3 mts of copper piping, insulation kit and 4 mts of 4 core copper flexible chord with cordless remote control etc., dual barrier coating in order to protect coil form oxidation. Makes: Blue star / Hitachi / Daikin/Lloyd (prevailing models in the market)

Supply, Fabrication of 1set MS bracket suitable for fixing outdoor unit of split AC unit.

Supply and installation of 5.0KVA Stabilizer of Makes: V-Guard / Real Guard / Uni Stab / ITL.

Supply installation Testing and commissioning of 20.0 KVA 312/360 V DC on line UPS system as per IEC 62040-I (Safety), IEC 62040-3 (Performance) for critical IT solutions, fully digital IGBT Converter and Inverter, SCR rectifier with Internal /External isolation transformer from DC to AC, PWM, pure sine wave output, double conversion, output pf 0.8, with paralleling facility, standard communication features/options auto and manual static by pass switch three phase input / Three phase output. acoustic level shall be less than 58dB at 1 mtr distance.Makes: As per list of recommended brands.Makes: Numeric/APC/Fuji Electric / Sakshham /Emerson

Supply and fixing of 10 passenger lift (680 Kg's) Kone make with speed 1 m/sec, with micro processor based VVVF drive with front entrance no of floors served Ground + 3 floors(4 stops & 4 openings), with a travel of 9.9 meters Approx, with car inside size 1300 mm Wide X1350 mm DeepX 2200 mm height , car clear opening 800 mm Wide X 2000mm Height with main power supply- 400/440V 3 phase 50 Hz for auxiliaries, car enclosure( Stainless steel and panels stainless steel -304 , ceiling stainless steel -304) center opening doors, with Micro Processor based Down collective simplex with electro mechanical door lock with seven segment digital display. The lift is provided with following features Battery operated emergency light and alarm bell, call register signal and Vf door operator, Landing push button in landing door frames, Automatic rescue device, Stainless steel button with SS cover, Digital position Indicator in car and landings, False ceiling in Car, Infra red door screen, Overload warning Indicator, SS hand rail on rear side etc., as approved by Eng-in-charge including cost and conveyance of all materials, labour charges, leads and lifts and finishing for finished item of work as directed by Engineer-in-charge

Supply of Visitor Chair (OXBO)SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D). BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. BACK SIZE : 46.5 cm. (W) x 60.5cm. (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. TUBULAR FRAME: The powder coated (DFT 40-60.microns) tubular frame should be cantilever type & made of Ø2.54 ±0.03cm. x0.2 ±0.016cm thick M.S.E.R.W. Tube. Overall Dimensions of Chair Seat Height - 46.5cm. Height - 93.5cm.Width & Depth of Chair as measured from pedestal - Width-61.0 cm and Depth-64.5 cm.

Hire charges of Shovel-0.50 cum- 75 hp(JCB) including fuel & crew charges for clearing of the heavy jungle and levelling the out side yard of the Sub-station premises as per the directions of the Engineer-at - site.

Dismantling of Brick masonry or R.R. Masonry in Cement mortar and transporting the debris to dumping yard as directed by the engineer at site including conveyance and labour charges etc, complete.

Dismantling of doors, windows (wood) with shutters, complete and and carefully stacking them useful for reuse within 100 metre lead .

Cost of Dismantled doors and Windows with frames including all materials, all labour charges etc. complete (the cost towards dismantled doors and Windows will be recovered at the local market rate).