REPAIRS TO TOILETS KITCHEN INTERNAL WATER SUPPLY LINES FLOORING WOODEN_ALUMINIUM JOINERY AND CONNECTED ITEMS IN CENRTAIN BUILDINGS IN TECHNICAL AND NON TECHNICAL AREAS AT INS KALINGA and INS KARNA

Amount

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed by the Engineer-in-Charge.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed by the Engineer-in-Charge.

Demolition of roof projections/drops, chajja drops and other thin RCC sections of width 10-20cm and thickness 7-10cm including cutting the reinforcement edges and finishing the disturbed surfaces with ave. 5mm thick CM 1:3 and three coats of white wash on ceilings etc. complete all as specified and as directed by the Engineer-in-Charge.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precastconcrete articles portions ordered to be dismantled complete all as specified and as directed by the Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge.

Taking down cement plaster of any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc built in cement mortar complete all as specified and as directed by the Engineer-in-Charge.

Taking down of chowkhats or frames n. exc. 1.5 sq.m. each complete all as specified and as directed by the Engineer-in-Charge.

Taking down of chowkhats or frames exc. 1.5 sq.m. but n. exc. 4.0 sq.m. each complete all as specified and as directed by the Engineer-in-Charge.

Taking down of chowkhats or frames n. exc. 1.5 sq.m. each but with shutters (without taking off shutters from the frames) complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description n. exc. 1 Sq.m. each complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description exc. 1 Sq.m. but n. exc. 2 Sq.m. each complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description n. exc. 1 Sq.m. each and refixing in the same opening complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description exc. 1 Sq.m. but n. exc. 2 Sq.m. each and refixing in the same opening complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description n. exc. 1 Sq.m. each and refixing in the other opening complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description exc. 1 Sq.m. but n. exc. 2 Sq.m. each and refixing in the other opening complete all as specified and as directed by the Engineer-in-Charge.

Resecuring or easing and adjusting without taking down shutters of any description n. exc. 1 Sq.m. each complete all as specified and as directed by the Engineer-in-Charge.

Resecuring or easing and adjusting without taking down shutters of any description exc. 1 Sq.m. but n. exc. 2 Sq.m. each complete all as specified and as directed by the Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed by the Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 15mm dia. steel tubing and connections complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 20mm dia. steel tubing and connections complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 25mm dia. steel tubing and connections complete all as specified and as directed by the Engineer-in-Charge.

Taking down PVC (SWR) pipes (of any radius) including joints etc. complete all as specified and as directed by the Engineer-in-Charge.

M&L for post construction anti termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia. holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed by the Engineer-in-Charge.

M&L for post construction anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and as directed by the Engineer-in-Charge.

M&L for PCC 1:5:10 type E2 (Using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed by the Engineer-in-Charge.

M&L for precast RCC 1:2:4 type B1 (Using 20mm graded stone aggregate) as in landings, cover slabs (for manholes etc.), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge.

M&L for grouting of concrete surfaces of columns, beams, slabs etc. with cement slurry by mixing 50 Kg of cement with 18 to 22 litre of water with admixture of FOSROC CEBEX 100 (Plastized expanding grout admixture) about 225 gms per 50 Kg of cement mixed with FOSROC NITOBOND AR (epoxy bonding agent) by drilling upto 12mm dia. hole in floor at the intervals as required at site upto required depth and grouting/pumping the grout with mechanically powered grout mixer 10-15 Kg of grout per each hole as per manufacturer's instructions and sealing the hole after grouting (GROUT= WATER+ CEMENT+ FOSROC CEBEX 100 in proportion) complete all as specified and as directed by the Engineer-in-Charge. Note: FOSROC NITOBOND AR will be measured and paid separately

M&L for sealing of floor/wall tile joint with NITOTILE GROUT (Cementing Tile Joint Filler) by uniform paste prepared with one part of water to 3 part of powder by volume complete all as per manufacturer's instructions complete all as specified and as directed by the Engineer-in-Charge

M&L for brickwork with fly ash bricks, straight or curved on plan n. exc. 6m mean radius, built in cement mortar 1:6 complete all as specified and directed by the Engineer-in-Charge.

M&L for second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F second class hard wood of 35mm thick plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers and fitted to chowkats complete all as specified and as directed by the Engineer-in-Charge.

S&F second class hard wood 30mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc, sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), supplied and fitted to chowkats complete all as specified and as directed by Engineer-in-Charge.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with 6mm thick teak wood beading all round complete all as specified and as directed by the Engineer-in-Charge.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube in opening as per specification & drawing complete all as specified and as directed by the Engineer-in-Charge.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails with mild steel frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, and with panelling of plain colour PVC sheet fitted in the mild steel frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 75mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed by the Engineer-in-Charge.

S&F 100mm size stainless steel butt hinges complete all as specified and as directed by the Engineer-in-Charge.

S&F 75mm size stainless steel butt hinges complete all as specified and as directed by the Engineer-in-Charge.

S&F 125mm size aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 125mm size aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed by the Engineer-in-Charge.

S&F 100mm size aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 100mm size aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed by the Engineer-in-Charge.

S&F 150mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 150mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed by the Engineer-in-Charge.

S&F 100mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 100mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed by the Engineer-in-Charge.

S&F 300mm long aluminium alloy, anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 300mm long aluminium alloy, anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 200mm long aluminium alloy, anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F aluminium plate type II gate and shutter, hooks and eyes 125mm size complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, aluminium plate type II gate and shutter, hooks and eyes 125mm size complete all as specified and as directed by the Engineer-in-Charge.

S&F 100mm long hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs 300mm, ordinary brass rat tail rod pattern springs including roller and roller plate complete all as specified and as directed by the Engineer-in-Charge.

S&F 150mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring,fixed in floor complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 150mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring,fixed in floor complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, mortice lock vertical type size 100mm of brass 4 lever complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, door closer hydraulically regulated of extruded aluminium section, designation No.3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg complete all as specified and as directed by the Engineer-in-Charge.

S&F aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 20mm dia., aluminium alloy anodised curtain rail including brackets complete all as specified and as directed by the Engineer-in-Charge.

S&F reinforcement TMT steel bars of 6 to 8mm dia. and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia. or securing with clips or welded complete all as specified and as directed by the Engineer-in-Charge.

S&F mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates; hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps; hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed by the Engineer-in-Charge.

M&L for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways railings, framework of water tanks and similar work conforming to Fe 290 Gde-E-165 for portions framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc for ornamental and intricate design complete all as specified and as directed by the Engineer-in-Charge.

M&L for anodised powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified (minimum thickness of powder coating 50 micron) complete all as specified and as directed by the Engineer-in-Charge.

S&F anodised powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21, 100mm long (2 Nos.) tower bolt 75mm (2 Nos.) suitable handle (1 No.) complete all as specified (minimum thickness of powder coating 50 micron) complete all as specified and as directed by the Engineer-in-Charge.

S&F anodised powder coated aluminium window and ventilator shutters, sliding type without sash bars, aluminium sections including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws and suitable anodised aluminium handles and rollers complete all as specified (minimum thickness of powder coating 50 micron) complete all as specified and as directed by the Engineer-in-Charge.

S&F anodised coloured aluminium grill of design No.DG-117, 10mm thick of DECOGRIL or equivalent make as approved by GE fixed with and including 'F' sections complete all as specified and as directed by the Engineer-in-Charge.

M&L for taking down aluminium door shutter exc. 1.5 Sq.m. but n. exc. 4 Sq.m. and refixing in the same opening with all screws and cleats after repairs by replacing the MS bolt 8mm dia. at the top and bottom of the shutter complete all as specified and as directed by the Engineer-in-Charge. Note: MS bolt will be measured and paid seperately.

S&F of MS long bolt 8mm dia. at the top and bottom of the aluminium door shutters complete all as specified and as directed by the Engineer-in-Charge.

M&L for taking down aluminium window openable shutter n. exc. 1.5 Sq.m. and refixing in the same opening with all screws and cleats after repairs by replacing the imax hinges (Friction hinges), glass, wire mesh etc. as required complete all as specified and as directed by the Engineer-in-Charge. Note: Imax (Friction) hinges, glass, wire mesh etc. will be measured and paid seperately.

S&F in repairs, stainless steel imax hinges (Friction stay window hinge) 200mm long for aluminium window fixed with screws complete all as specified and as directed by the Engineer-in-Charge.

M&L for taking down aluminium sliding window shutter n. exc. 1.5 Sq.m. and refixing in the same opening with all screws and cleats after repairs including the replacement of rollers etc. complete all as specified and as directed by the Engineer-in-Charge.

M&L for 18mm thick cupboard shutter, plywood grade BWP type BB with 6mm thick teak wood beading all round fixed with screws to timber frame work complete all as specified and as directed by the Engineer-in-Charge.

M&L for 1.50mm thick decorative laminate type 1 of surface finish, colour and pattern as approved by the GE, fixed with approved adhesive as per manufacturer's instructions on flat or curved surfaces in any size or width complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, for 12mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed by the Engineer-in-Charge.

M&L for 100mm thick PCC 1:4:8 type D2 (Using 40mm graded stone aggregate) as in sub base for flooring complete all as specified and as directed by the Engineer- in-Charge.

M&L for 40mm thick PCC 1:2:4 type B1 (Using 20mm graded stone aggregate) as in sub base for flooring complete all as specified and as directed by the Engineer- in-Charge.

M&L for 25mm thick PCC 1:2:4 type B1 (Using 20mm graded stone aggregate) as in sub base for flooring complete all as specified and as directed by the Engineer- in-Charge.

M&L for non skid/matt finish ceramic tiles 7 to 8mm thick area of each tile exc. 0.18 Sq.m. but n. exc. 0.38 Sq.m. (600x600mm size), in floors etc.set and jointed in neat slurry and pointed in white or coloured cemment to match for joint free over screed bed or bedding layer 15mm thick in CM 1:4 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

M&L for non skid/matt finish ceramic tiles 7 to 8mm thick area of each tile exc. 0.18 Sq.m. but n. exc. 0.38 Sq.m. (600x600mm size), in vertical surface like skirtings dado etc. set and jointed in neat slurry and pointed in white or coloured cemment to match for joint free over screed bed or bedding layer of mortar 10mm thick in CM 1:4 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

M&L for non skid/matt finish ceramic tiles 7 to 8mm thick area of each tile exc. 0.11 Sq.m. but n. exc. 0.18 Sq.m. (400x400mm size), in floors etc.set and jointed in neat slurry and pointed in white or coloured cemment to match for joint free over screed bed or bedding layer 15mm thick in CM 1:4 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

M&L for non skid/matt finish ceramic tiles 7 to 8mm thick area of each tile exc. 0.11 Sq.m. but n. exc. 0.18 Sq.m. (400x400mm size), in vertical surface like skirtings dado etc. set and jointed in neat slurry and pointed in white or coloured cemment to match for joint free over backing coat of mortar 10mm thick in CM 1:4 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

M&L for glazed ceramic tiles in vertical surface like skirtings dado etc., of size 250x450x7mm or 300x450x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match for joint free over backing of 10mm thick in CM1:4 on fair faces of brick work or concrete surfaces complete all as specified and directed by the Engineer-in-Charge.

M&L for vitrified coloured ceramic tiles 10mm thick (square/ rectangular) polished, area of each tiles n. exc. 0.36 Sq.m., in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed of 15mm thick in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M&L for vitrified coloured ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles n. exc. 0.36 Sq.m., in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over a backing coat of 10mm thick in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M&L for machine cut Kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over screed bed or bedding layer of mortar 15mm thick in CM 1:4 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

M&L for machine cut Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over a backing coat of 10mm thick in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M&L for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs including strips in door portion 20 to 30mm wide, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over a screed bed or bedding layer of CM 1:4, 15mm thick complete all as specified and as directed by the Engineer-in-Charge.

M&L for grinding the existing Kota/Marble flooring/skirting with suitable grit size carborundum stones removing black spots and other faded surfaces on existing terrazzo floors/dado with machine/hand grinding, grouted with cement cream, mixed with admixtures of existing floor tint where required and rubbed hard with felt and slightly moistured oxalic acid powder @ 5gm/Sq.m. of floor area, cleaning floor with diluted oxalic solution and drying polished floor with machine fitted felt or hessian bobs and making the floor/skirting to shine with wax polish complete all as specified and as directed by the Engineer-in-Charge.

M&L for glass dividing strips 3mm thick, 28mm wide fixed in to concrete flooring complete all as specified and as directed by the Engineer-in-Charge.

M&L for rendering 10mm thick with CM 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L for rendering 10mm thick with CM 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement including finishing with sagol finish not less than 1mm thick complete all as specified and as directed by the Engineer-in-Charge.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:3 mixed with water proofing compound as per manufacturer's instructions finishing the surface even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge. Note: WPC will be measured and paid seperately.

Supply only Integral Water Proofing Compound (ISI marked) of approved make.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over one coat of primer complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper over one coat of primer including 3mm thick wall care putty on walls complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement based paint over one coat of primer complete all as specified and as directed by the Engineer-in-Charge.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in square n. exc. 0.5 Sq.m. in each pane complete all as specified and as directed by the Engineer-in-Charge.

S&F 5.5mm thick sheet glass, ordinary quality and glazing with oil putty in square n. exc. 0.5 Sq.m. in each pane complete all as specified and as directed by the Engineer-in-Charge.

S&F 4mm thick figured glass, pin head type and glazing with oil putty in squares n. exc. 0.5 Sq.m. in each pane complete all as specified and as directed by the Engineer-in-Charge.

M&L for removal and refixing of 5.5mm thick glass panes n. exc. 0.5 Sq.m. each to the existing aluminium frame including sealing with silica gel after removing the damaged silica gel complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of new or previously untreated steel surfaces of any description, n. exc. 10cm in width or girth when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint over a priming coat of red oxide zinc chrome primer complete all as specified and directed by the Engineer-in-Charge.

M&L for preparation of new wooden surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of old painted wood and wood based surfaces over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

M&L for writing letters or figures (Black, Roman, Italic or Indian) n. exc. 30cm height complete all as specified and as directed by the Engineer-in-Charge.

S&F 20mm dia. (15mm internal dia.) 3-layer PP-R polypropylene random copolymer pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 25mm dia. (20mm internal dia.) 3-layer PP-R polypropylene random copolymer pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F 32mm dia. (25mm internal dia.) 3-layer PP-R polypropylene random copolymer pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F GI spout 40mm dia. medium grade placed on sunken floor complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, bib taps 15mm dia. fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, two way bib cock 15mm dia. chromium plated, fancy type of make Jaquar Catlogue No.FON-40041 or equivalent in CERA complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 15mm dia. stop valves, fancy type, chromium plated with long shank and cup (Concealed type), cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 15mm dia. chromium plated angle stop valves, fancy type, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 15mm dia. chromium plated pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, brass CP 2 in 1 mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, health faucet 15mm dia. with one meter long easy flex tube in chromium finish and wall look of make Jaquar Catlogue No.ALD-CHR-565 or equivalent in CERA complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 125mm dia. chromium plated brass shower rose with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, tubular towel rail brass chromium plated, 20mm dia., 60cm long between flanges complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, towel ring round with round flange of make Jaguar Catlogue No.ACN-1121BN or equivalent make as approved by GE complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 25mm dia. PP-R globe or gate valve with steel ball, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 32mm dia. PP-R globe or gate valve with steel ball, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mmx460mm bowl size 410mmx 330mmx160mm complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mmx420mm bowl size 410mmx 330mmx160mm complete all as specified and as directed by the Engineer-in-Charge.

S&F prefabricated stainless steel sink of required size made out of 2mm thick stainless steel plate of SS 304 including stainless steel out let pipe 75mm dia. and making perforated holes at the mouth of outlet pipe etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, vitreous China squatting pan, ‘Orissa’ pattern with PVC P trap, size 580x440mm white, with integral foot rests complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, vitreous China wash down water closet pan (pedestal pattern), white including fixing bolts, flushing cistern and flush pipe and seat cover etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, vitreous China urinals, half stall type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, wash hand basin of size 550x400 vitreous China (flat back or angle back type) including half pedestal and cutting for and pinning in ends of brackets or erecting stand including supply and fixing of waste coupling, waste pipe etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 10 Litres calacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32mm dia. and connection to pipes and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, PVC flexible connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed by the Engineer-in-Charge.

S&F soap dish, chromium plated brass, of approximate size 160x160x90mm, fixed to plugs with chromium plated brass screws complete all as specified and as directed by the Engineer-in-Charge.

S&F toilet paper holder brass chromium plated fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 700 Litres capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) two layered ISI marked hoisted and fixed in position complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 1000 Litres capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) two layered ISI marked hoisted and fixed in position complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 2000 Litres capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) two layered ISI marked hoisted and fixed in position complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, PVC water tank cover of make Sintex or equivalent to match the existing tanks complete with locking arrangement suitable for 500-1000 Litres capacity complete all as specified and as directed by the Engineer-in-Charge.

S&F PVC (SWR) pipes 110mm dia. single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by the Engineer-in-Charge.

S&F PVC (SWR) pipes 75mm dia. single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by the Engineer-in-Charge.

S&F 50mm dia. PVC waste pipes for WHB/sink fixed to walls including fiitings and connecting to multiple floor trap complete all as specified and as directed by the Engineer-in-Charge.

S&F 40mm dia. PVC waste pipes for WHB/sink fixed to walls including fiitings and connecting to multiple floor trap complete all as specified and as directed by the Engineer-in-Charge.

S&F 110mm dia. PVC (SWR) plain bends any radius complete all as specified and directed by the Engineer-in-Charge.

S&F 75mm dia. PVC (SWR) plain bends any radius complete all as specified and directed by the Engineer-in-Charge.

S&F 110mm dia. PVC (SWR) bends any radius provided with access door complete all as specified and directed by the Engineer-in-Charge.

S&F 75mm dia. PVC (SWR) bends any radius provided with access door complete all as specified and directed by the Engineer-in-Charge.

S&F 110mm dia. PVC (SWR) junction single (Single T) equal or uneaqual provided with access door complete all as specified and directed by the Engineer-in-Charge.

S&F 75mm dia. PVC (SWR) junction single (Single T) equal or uneaqual provided with access door complete all as specified and directed by the Engineer-in-Charge.

S&F PVC (SWR) vent cowls 110mm dia. complete all as specified and as directed by the Engineer-in-Charge.

S&F PVC (SWR) multi floor trap 75mm dia. outlet with grating including jointing with solvent cement complete all as specified and directed by the Engineer-in-Charge.

S&F PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed by the Engineer-in-Charge.

S&F grating doom 125mm dia. with waste hole of PTMT (Min weight 40 gms) complete all as specified and as directed by the Engineer-in-Charge.

M&L for repairs to the existing floor trap by demolition of PCC including tiles & screed bed for the floor area of 200x200mm around the floor trap, provision of 110mm dia. PVC (SWR) pipe vertically for the depth of 20 to 30cm from the floor level up to the floor trap embedded in PCC 1:2:4 type B1 and making good with the existing floor finish including provision grating complete all as specified and as directed by the Engineer-in-Charge.

M S G CONSTRUCTIONS