IMPROVEMENT OF EFFICIENCY OF WATER SUPPLY INSTALLATION BY REP/REPLACEMENT OF SPARE PARTS OF MOTOR STAR DELTA STARTER APFC PANEL AIR COMPRESSOR REWINDING OF PUMPS MOTORS AND OTHER EQUIPMENT AT MIL STN PITHORAGARH UNDER GE PITHORAGARH

Amount

Material and Labour in replacement of single phase preventor (supply monitoring device), 415V, 3P3W, 50 hz including electric connection complete all as specified and directed. Make- L&T (as per sample) or equivalent make

Material and Labour in replacement of Contractor MNX 32A, 3P and Front Mounting Add-on aux. Contact Block MNX 2 NO + 2 NC Make- L&T

Material and Labour in replacement of Over load relay 20-30A, MN2 Make- L&T

M&L including jointing and testing of CI wedge gate sluice valves of 150mm dia class 150, PD Type,bolted bonnet outside screw & Yoke type rising stem, ISI marked, flanged ends, drilled having stainless steel spindle with cast iron wheel at top complete with nut bolts, washer and rubber gasket complete all as specified . Make : SANT/KIRLOSKAR/LEADER

Material and Labour in replacement of three pole contactor ML 12 suitable for 150/100HP star delta starter including electric connection complete all as specified and directed. Make-L&T or equivalent in HPL/Havells

Cutting of bushes , grass, small trees at water supply installations or where directed as per requirement and disposal of the same to a distance not exceeding 50 mtr all as directed.

Supply and laying in replacement of high voltage insulation mat (blue in colour) made of elastomeric polymers material having a high insulation resistance, thus imparting total safety of human being from any leakage current, having high insulation resistance of class B of size 2.5 mm thick and 1.0 m width LT grade confirming to IS - 15652 : 2006, including pasting of mat with SR-998 by adding thinner as per requirement complete all as specified and directed. Make- Jyoti / Electrosafe / Vardhman

Taking down existing alum mixing gear mechanism & motor from base, overhauling, greasing, servicing complete and fitting back after repairing of PCC (1:3:6) Base of size 0.60mx0.40mx0.10m .all as directed

Material and Labour for dismantling of main gear box assembly mounted on sedimention tank and cleaning, overhauling,greasing and replacement of gear oil approx 10 ltr , lathe work on Gear drum/pininon and shaft wheel gear with proper alignment and refixing in same location including testing complete all as directed.

Material and Labour for dismantling of sluice valve spindle clear stainless steel assembly complete with opening of nut & bolt with long handle with lathe work and replacement of gland/packing to repair leakage from valve of size 300/150mm including replacement of spandle assembly complete all as directed.

M & L for preparation of old painted surface of panels- 5 Nos, 150mm pipe lines- 30Mtr, railing and Chaqured plate- 20 Nos etc and protect meters, switches, duct cover from painting and paint with spray gun with one coat of existing paint complete all as specified and directed

M & L for preparation of old painted surface with the help of paint remover, scrapper & fine ambery paper and painting with tow coat of heat resistance paint with the help of spray gun on 150/120/100 HP Centrifugal pump set including motor, and writing SM No/ Maching No and connect back all Electrical connection and testing complete all as specified and directed.

M & L for preparation of old painted surface with the help of paint remover, scrapper & fine ambery paper and painting with tow coat of heat resistance paint with the help of spray gun on 30/12.5 HP Centrifugal pump set including motor, and writing SM No/ Maching No and connect back all Electrical connection and testing complete all as specified and directed.

M & L for preparation of old painted surface with the help of paint remover, scrapper & fine ambery paper and painting with tow coat of heat resistance paint with the help of spray gun on 5/1/.5 HP Centrifugal pump set including motor, and writing SM No/ Maching No and connect back all Electrical connection and testing complete all as specified and directed.

Material and Labour for preparation of old painted surface and applying one coat of synthetic enamel paint ( existing colour ) first quality on NRV /Sluice valve of any size complete all as specified and directed.

Material and Labour for disconnecting motor 150 HP all electrical connections , removing the motor from the base and opening up the motor carefully and cleaning, servicing,greasing including varnishing complete, heating, replacement of worn out bearing with new bearing and reassembling, mounting the same,including testing on full load up to entire satisfaction, complete all as directed . Note:- (i) The cost of bearing as per sample deemed to be included in the quoted rates. (ii) other Spare parts shall be measured and paid separately under respective items

All as per Item No 17 above but 125 HP

All as per Item No 17 above but 120 HP

All as per Item No 17 above but 100 HP

All as per Item No 17 above but 30/25 HP

All as per Item No 17 above but 3/5 HP

All as per Item No 17 above but 0.5/1.0 HP

Material and Labour for disconnecting all electrical connections , removing the pump 150 HP from the base and opening up the pump carefully and overhauling , cleaning, servicing, greasing and including replacement of worn out bearing,worn out gland bush,and reassembling, mounting the same, including testing on full load up to entire satisfaction , complete all as directed. Note:- (i) The cost of bearing as per sample deemed to be included in the quoted rates. (ii) other Spare parts shall be measured and paid separately under respective items

All as per Item No 24 above but 125 HP

All as per Item No 24 above but 120 HP

All as per Item No 24 above but 100 HP

All as per Item No 24 above but 30/25 HP

Supply only grease all as specified and directed Make- Servo

Supply only Gland of Size 10mm all as specified and directed

Supply only Gland of Size 12mm all as specified and directed

Supply only Gland of Size 14mm all as specified and directed

Dismantling and servicing the complete unit of automatic servo stabilizer oil cooled type 3 phase, 440 Volts 50 Hz including disconnecting & taking out oil from oil cooled stabilizer capacity 30 KVA Make- paradise including cleaning & segregating the unserviceable/serviceable parts, servicing, oiling, greasing of mechanical mechanism at operation complete all as directed including cleaning of inner surface of oil tank. Nuts, bolts, washers, packing etc. of required size and screws shall also deemed to be included in this work. This work shall not include cleaning old transformer oil, dehydrating & filtration machine and refilling the treated oil in tank andwhich shall be paid under appropriate item. Testing of stabilizer shall be carried out after repair at full load for manual/automatic operation & for corrected out put at variable input (within permissible limit) and cut off operation at low voltage complete all as specified and directed.

All as per item No. 33 above but for air cooled automatic voltage stabilizer 3 phase 440 Volts having capacity 10 KVA servo type complete all as specified and directed. Make: Nayar Power Control or equivalent.

All as per item No. 33 above but for oil cooled automatic voltage stabilizer 3 phase 440 Volts having capacity 05 KVA servo type complete all as specified and directed. Make: Blue bird or equivalent

S&F in replacement of Automatic phase sequence corrector with automatically correct input supply, Reverse Phase and also protection gainst single phasing, voltage unbalancing, low voltage high voltage with time delay motor upto 25 to 30 HP complete all as specified and directed

Supply and Fixing in replacement of PVC insulated unsheathed multi stranded copper conductor cable 1100 volts grade single core of 120 Sqmm size from LT panel to starter and starter to motor including crimping of copper lugs -06 nos, complete all as directed. Make-Havells/Polycab/Finolex

All as per Item No 37 above but 150 Sqmm size complete all as directed. Make-Havells/Polycab/Finolex

Supply and Fixing in replacement Off load changeover 400/315A 4 Pole 415volts , 50Hz with suitable side handle complete all as specified and directed.

Supply and Fixing in repair neon blub indicating lamp assembly complete all as directed.

Supply and Fixing in replacement Digital type Volt meter (0-500V) flush mounted three phase class 1.0 size of size 96x96 sqmm complete all as specified and directed. Make-AE/HPL/IMP

All as per Item No 42 above but Digital Type (0-600A) Amp meter

Supply and Fixing in replacement of Current transformer (CT) of range 100/5 A complete all as specified and directed. Make-AE/Crompton/Pragati

Material and Labour for Earthing complete with galvanized steel earth plate electrode, 600X600X 6 mm thick, buried directly in ground (earth pit not less than 2.25 Mtr deep below ground level) with top edge of the earth plate not less than 1.5 Mtr below normal ground level, connected to galvanized earth strip 32x6 mm by means of galvanised iron or steel all as shown in electrical plate No. 3 on SSR Part I connected to elelctrical equipments all as directed or indicated including Excavation & earth work, construction of PCC pit with RCC cover, watering pipe 20mm dia light grade with funnel & wire mesh & testing all as directed.

Supply and Fixing in replacement GI strip 32 x 6 mm complete laid in trenches / ducts fixed on steel structure complete all as specified and directed.

Material and Labour for opening up the motor 150 HP carefully and removing burnt windings from stator and rewinding with suitable gauge of supper enamelled copper insulated wire and superior insulating material including varnishing, heating, greasing replacement of worn out bearing, reassembling the same,including testing on full load up to entire satisfaction, complete all as directed ..

All as per Item No 47 above but 125 HP

All as per Item No 47 above but 100 HP

All as per Item No 47 above but 30/25 HP

All as per Item No 47 above but 12.5 HP

All as per Item No 47 above but 3/5 HP

All as per Item No 47 above but 0.5/1.0 HP

Supply and fixing in replacement of MS coupling set including rubber bush and MS bolts suitable for 100 to 150 HP Pump complete all as directed.

S&F in replacement MS coupling set suitable for 30/25 HP Pump complete all as directed.

S&F in replacement rubber coupling suitable for 12.5 HP Pump complete all as directed.

S&F in replacement rubber coupling suitable for 30/25 HP Pump complete all as directed.

S&F in replacement of coupling rubber bush -12Nos with MS bolts suitable for 100 to 150 HP Pump complete all as directed.

S&F in replacement pump bearing No NU210 complete suitable for 100 to 150 HP Make- NBC

S&F pump bearing No 7310 complete suitable for 100 to 150 HP Make- NBC

S&F pump bearing No 2310 complete suitable for 100 to 150 HP Make- NBC

S&F motor bearing No NU316 complete suitable for 100 to 150 HP Make- NBC

S&F motor bearing No 6316 complete suitable for 100 to 150 HP Make- NBC

S&F motor bearing No 6315 complete suitable for 100 to 150 HP Make- NBC

S&F motor bearing No 6317 complete suitable for 100 to 150 HP Make- NBC

S&F motor bearing No 6310 complete suitable for 25/30 HP Make- NBC

S&F in replacement of stainless steel shaft with check nut etc complete suitable for 100 to 150 HP centrifugal pump complete all as specified and directed. Make KSB/Kirloskar

S&F in replacement of stainless steel shaft with check nut etc complete suitable for 30/25 HP centrifugal pump complete all as specified and directed. Make KSB/Kirloskar

S&F in replacement of inter stage gunmetal/ brass bush complete suitable for 100 to 150 HPcentrifugal pump complete all as specified and directed. Make KSB/Kirloskar

S&F in replacement of both end long gunmetal/ brass bush complete suitable for 100 to 150 HP centrifugal pump complete all as specified and directed. Make KSB/Kirloskar

Supply only pressure plate with balancing disc suitable for 100 to 150 HP centrifugal pump complete all as specified and directed. Make KSB/Kirloskar

S&F in replacement of gun metal impeller complete suitable for 100 to 150 HP centrifugal pump complete all as specified and directed. Make KSB/Kirloskar

S&F in replacement of gun metal impeller complete suitable for 25/30 HP centrifugal pump complete all as specified and directed.

Material and Labour in replacement of glands suitable for 100 to 150 HP centrifugal pump complete all as specified and directed.

Material and Labour in replacement of glands suitable for 30/25HP centrifugal pump complete all as specified.

Supply and Fixing in replacement pressure gauge of suitable size for 100 to 150 HP pump set complete all as specified and directed.

Supply and Fixing in replacement pressure gauge of suitable size for 30/25/5/3 HP pump set complete all as specified and directed.

Repair/ Replacement of fan belt of existing size and dia of main gear assy mounted on sediment tank complete all as directed .

Repair/ Replacement of fan belt of existing size and dia of motor mounted on sediment tank complete all as directed.

Supply and Fixing in replacement Copper Cable lugs of size 120 Sqmm for connection to copper cable complete all as specified and directed.

Supply and Fixing in replacement Copper Cable lugs of size 150 Sqmm for connection to copper cable complete all as specified and directed.

Supply and Fixing in replacement Cable lugs of size 70Sqmm for connection to copper cable complete all as specified and directed.

S&F in replacement of motor connection pad assembly with existing size of upto 150 HP motor complete

S&F in replacement of bearing housing RKB23 of make Kirloskar pump with existing size 150 HP pump complete

S&F in replacement of Automatic phase sequence corrector with automatically correct input supply, Reverse Phase and also protection against single phasing, voltage unbalancing, low voltage high voltage with time delay motor upto 100 to 150 HP complete all as specified and directed

S&F cast iron air valves with two air outlets, 150mm dia bore and fixing in cast iron water supply mains including all fixing arrangement complete all as specified and directed.

M&L for laying common burnt bricks, sub class 'B', of size 230 x 115 x 75 mm in trenches for cable protection complete all as directed by Engr-in-charge.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5 M. deep for foundation or for laying of pipes etc and getting out in hard/dense soil, comlete all as specified and directed

Returning filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm in hard/dense soil, complete all as specified and directed

Removing excavated soil to a distance exceeding 50m but not exceeding 250 m and depositing where directed at a level not exceeding 1.5 m above the starting point , complete all as specified and directed.

Supply and laying including taking up in trenches, under floor or fixed to walls XLPE insulated cable, screened PVC bedded, galvanised steel strip or wire armoured, electric power cable heavy duty 1100 Volts grade with stranded aluminium conductor of size 95 Sq mm 3.5 Core complete all as specified and directed.

Supply and spreading of clean dry river sand in trenches/ transformer yard/ two pole structure yard for cable protection complete all as directed

M/S Shahjee Fridge Service

m/s vishnu kumar agarwal