Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹88.5 LAccepted-AOC THAKURPARA MELAGHAR SEPAHIJALA PIN 799115 | MELAGHAR | SEPAHIJALA | TRIPURA | 799115 | ₹88.5 L | L1 | Accepted-AOC Reasonable |
| 2 | L2₹89.7 LRejected-Finance BISHALGARH SEPAHIJALA TRIPURA | SEPAHIJALA | TRIPURA | 799011 | ₹89.7 L | L2 | Rejected-Finance High Rate |
Tender Value
₹1.1 Cr
EMD Value
₹2.2 L
Closing Date
27 Jan 2026, 3:00 pmClosed
The Executive Engineer,BishalgarhDivision,PWD(RnB)
O/O Executive Engineer,BishalgarhDivision,PWD(RnB)
SH_Paver Block, Flat brick Soling, WBM_II, WBM_III, Brick Masonry work, RCC Drain and other ancillary works_Ch_0point00 to 0point350 Km (L_0point350 Km)(2nd Call)
2026_CEPWD_68847_1
186_R_DNIT_SEIV_PWD(RnB)_24_25
Open Tender
Civil Works - Roads
120 days
Bishalgarh
Please refer Tender documents.
5 documents required · 5 mandatory
₹4,000
₹2.2 L
25 Mar 2026
5 Jan 2026
27 Jan 2026
5 Jan 2026
27 Jan 2026
5 Jan 2026
5 Jan 2026 - 22 Jan 2026
Removal of Unsuitable Soil with Disposal upto 1000 m: Removal of unsuitable soil including excavation, loading and disposal upto 1000 m lead but excluding compaction ground upporting embankment / subgrade, replacement by suitable soil, which shall be paid separately as per MoRD Technical Specification Clause 303.5.2 and as per MoRD Technical Specification Clause 302.3.11.
Granular Sub-base with Well Graded Material (Table 400.1) using Jhama Brick Aggregate: (A) By Mix in Place Method Construction of granular sub-base by providing well graded material (Jhama Brick Aggregate, Grading-I, as per Table 400.1, spreading in uniform layers with tractor with attachments on prepared surface, mixing by mix in place method with rotavator at OMC, applying and brooming sand to fill up the interstices of coarse aggregate, watering and compacting with smooth wheel roller to achieve the desired density, complete as per MoRD Technical Specification Clause 401. (i) For Grading - I Material (jhama brick aggreate)
WBM Grading - 3 Providing, laying, spreading and compacting jhama brick aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing rolling with three wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density Grading- 3 as per MoRD Technical Specification Clause 405. (A) By Manual Means
80 mm thick factory made c.c. interlocking paver block of M-35 Grade: Providing and laying factory made chamfered edge Cement Concrete paver blocks of required strength, thickness & size/ shape, made by table vibratory method to attain superior smooth finish using PU or equivalent moulds, laid in required grey colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. all complete as per specifications & approval/ direction of the Engineer -in-Charge: (a) 80 mm thick c.c. paver block of M-35 grade with approved colour, design and pattern
Tack coat using hot straight run bitumen of grade VG-30 on W.B.M. : Providing and applying tack coat using hot straight run bitumen of grade VG-30, including heating the bitumen, spraying the bitumen, cleaning and preparing the existing road surface as per specifications: On W.B.M. @ 0.75 kg/ sqm.
20 mm thick Open-Graded Premix Carpet using Bituminous (Viscosity grade/ modified bitumen) Binder: Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using Viscosity grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base , including mixing in a suitable plant, laying and rolling with a three wheel 80 - 100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C or Type D as per MoRD Technical Specification Clause 508. Case - I : By Manual Means (I) Bitumen of VG-30
Seal Coat Providing and laying seal coat sealing the voids in a bituminious surface laid to the specified levels, grade and cross fall using Type A or Type B or Type C or type D as per MoRD Techinical Specification Clause 510 A. By Manual Means Case - IV : Type D (premix with fine sand) (I) Bitumen of VG-30
Excavation for Structures: B. With dewatering Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, dewatering, construction of shoring, shuttering & bracing, removal of stumps & other deleterious material and disposal upto a lead of 50 m, dressing of sides & bottom and backfilling in trenches with excavated suitable material. I. Ordinary Soil (i) Upto 3 m depth
Filling in foundation trenches as per drawing & MoRD technical specification Clause 305.3.9, 1200. I. Sand Filling
Providing concrete for plain/reinforced concrete in open foundations complete including formwork as per drawings & MoRD technical specifications Clauses 802, 803, 900, 1202 and 1203. (including centering, shuttering, staging etc. but excluding reinforcement). I) P.C.C grade M 10 (i) Nominal mix 1:3:6
Supplying, fitting & placing Thermo-Mechanically treated bar/ Cold twisted deformed steel bar reinforcement in foundation complete as per drawings & MoRD technical specifications Clauses 1000 & 1202.
Brick masonry work in cement mortar in foundation completed excluding pointing & plastering as per drawing & MoRD technical specifications Clauses 600, 1202 & 1203. II) Brick masonry in 1:4 cement mortar
Plastering with cement mortar (1:4) 12 mm thick on brickwork/ C.C. work including a finishing coat of neat cement punning with 2.75 kg of cement per sqm in substructure as per MoRD technical specification Clauses 613.4 & 1204.
Providing concrete for plain/reinforced concrete in open foundations complete including formwork as per drawings & MoRD technical specifications Clauses 802, 803, 900, 1202 and 1203. (including centering, shuttering, staging etc. but excluding reinforcement). IV R.C.C grade M 20
Providing weep holes in brick masonry/ stone masonry, plain/ reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe or uPVC pipe (110 mm OD of 6.0 kg/cm2 pressure) extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and MoRD technical specification clauses 614, 709, 1204.3.7
Providing & laying filter media with jhama brick aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil & bigger size towards the wall & providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and MoRD technical specification clause 1204.3.8.
Road Safety Convex Mirror Providing and fixing pole mounting (50 mm dia steel pole of standard height) 800 mm dia strong unbreakabale highly reflective road safety convex mirror body made up of poly carbonate having large viewing angle from standard distance (minimum 6 m) firmly fixed to the gound by means of properl designed foundation with M-15 grade cement concrete 450mm x 45mm x 600 mm as per IRC guideline/ MoRT&H Technical Specification Clause 801.
Providing structural steel work in single section fixed with or without connecting plate including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as required.
Reinforced Cement Concrete Crash Barrier: Provision of an Reinforced cement concrete crash barrier at the edges of the road, approaches to bridge structures and medians, constructed with M-20 grade concrete with TMT reinforcement conforming to IRC:21 and dowel bars 25 mm dia, 450 mm long at expansion joints filled with premoulded asphalt filler board, keyed to the structure on which it is built and installed as per design given in the enclosure to MOST circular No. RW/NH - 33022/1/94-DO III dated 24 June 1994 as per dimensions in the approved drawing and at locations directed by the Engineer, all as specified as per MoRT&H Technical Specification Clause 811
Please Enable Macros to View BoQ information
stage.html
html • 0.04 MB
tech_eval.pdf
fin_eval.pdf
aoc.pdf
finance_70045.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Tendernotice_1.pdf
PDF • 2.49 MB
Upload_DNIeT.pdf
Tender Documents • 3.17 MB
BOQ_70045.xls
BOQ • 0.26 MB
IntyegrityPact.pdf
Additional Documents • 0.49 MB
Download all tender documents and submit your bid