Repairing, Renovation and Civil Work as per Requirement at Municipal Building In S.P.Stadium ward at West Zone.(ARC)

1. Name of Work : Repairing, Renovation and Civil Work as per Requirement

Municipal Building In S.P.Stadium ward at West Zone.(ARC)

2. Tender Estimated Cost : Rs:-

: 1% of the Tender Cost in the form of Rs. 29,997.00 (D.D. / Pay

3. Earnest Money

- Order / Local Micr Check/B.G.)

4 Tender Fee Rs : Demand Draft of Rs.1500.00

5 S.D. : 5 % of tender amount

6. Time-Limit : 12 months

7. Validity Period : 120 Days

(a) Eligibility Criteria Register “E1” class in PWD in Govt. R&B/CPWD/AMC or

equivalent registration with any other state Govt. or

8. (i) Last Date of Submission of :

Dt.17-07-2026, upto 18:00 hrs.

(ii) Mode of Sending : a) In Sealed cover in duplicate copies by Registered Post

A.D, or by Courier.or hand delivery

b) Tender sent by ordinary post will be rejected out right.

(iii) Description essential to :

a) Name of work, Tender Notice No. & Tender No.

be made on sealed cover

b) Date of receiving tender by Corporations.

(iv) Mode of quoting rates in : The Price bid shall be submitted online only.

Schedule of Quantities and

Rates It shall not be submitted Physically.

9. Date of Opening : Dt.18.07.2026 , 15:00 hrs.

10 Place of Submission & : Submission of EMD. Tender fee and other Documents during office

Opening of Tender hours: On date. 18-07-2026 & 12:00 hrs West Zone, 2nd Floor,

A.M. Office, Dr. Ramanbhai Patel Bhavan, Usmanpura.Ahmedabad

Municipal Corporation, W.Z. Office, Ahmedabad-380013.

11 Penalty Due to Delay of work (1) Rs.1000/- per day (for tenders amounting upto 10 Lakhs), (2)

Rs.2500 per day (for tenders amounting above 10 Lakhs and upto

30 Lakhs), (3) Rs.5000 per day (for all tenders amounting above

Lakhs) but not more then 10% of bill

Defect Liability : As per ‘B-1 Form Close

Whenever a work is allotted by Engineering staff, whether minor or

major of part thereof of any amount, the contractor shall be bound to

start the works within 48 hours of intimation of work. Communication

done telephonically via SMS, Via Whatsapp and through letter / E-

mail shall be considered legal and binding for the same. Failure of

comply to start the works in 48 hours of intimation as above by

Time permitted to start parts

contractor the contractor shall be levied penalty of (1) Rs.1000/- per

day (for tenders amounting upto 10 Lakhs), (2) Rs.2500 per day (for

tenders amounting above 10 Lakhs and upto 30 Lakhs), (3)

Rs.5000 per day (for all tenders amounting above 30 Lakhs). Three

times failures by contractor shall make contractor responsible to be

black listed unless and otherwise justified properly in writing /

binding within 15 days of last notice of penalty.

 The staff of the contractor shall wear safety jackets,

hoes, helmets etc. while on duty and any violation will attract

fine of Rs. 5,000/- for each incident.

Safety Failure to erect safety signage or trying to carry out he

works without proper precautions/safety measures as

equired will attract a fine of Rs. 5,000/- for each incident.

The contractor shall be responsible to make good and remedy at

his own expense any defect which may develop or may be noticed

before the period mentioned hereunder from the certified date of

completion, The within 15 days of receipt of the notice. In the case

of failure on the part of the contractor, the Engineer-in-charge may

rectify or remove or re-execute the work at the risk & cost of the

contractor. The Engineer-in-charge shall be entitled to appropriate

the whole or any part of the amount of security deposit towards

the expenses, if any, Incurred by him in rectification, removal or re-

execution. The Defects Liability period shall be as under(a) for all

works costing upto Rs. 50,000 ( amount put to tender), the period

Defect &Liability Period shall be 3 months from the certified date of completion.

(b) for all works costing more than Rs. 50,000 and upto Rs. 1 crore

(amount put tender), the period shall be 6 months from the

certified date of completion or one monsoon, whichever is later.

(c) for major projects costing more than Rs. 1 crore, the period

shall be 12 months from the certified date of completion which

should include one monsoon.

(d) For building works, the period specified in (a), (b) or (c) above

OR elapse of monsoon period following the certified date of

completion, whichever is later. For the purpose of deciding the

monsoon period, the 30th September may be treated as the last

Compensation for Delay 10% of Remaining work (As per Circular)

Whenever a work is allotted by Engineering staff, whether minor

or major of part thereof of any amount, the contractor shall be

bound to start the works within 48 hours of intimation of work.

Communication done telephonically via SMS, Via Whatsapp and

through letter / E-mail shall be considered legal and binding for

the same. Failure of comply to start the works in 48 hours of

Time permitted to start parts intimation as above by contractor the contractor shall be levied

16 of work penalty of (1) Rs.1000/- per day (for tenders amounting upto

Lakhs), (2) Rs.2500 per day (for tenders amounting above

Lakhs and upto 30 Lakhs), (3) Rs.5000 per day (for all tenders

amounting above 30 Lakhs). Three times failures by contractor

shall make contractor responsible to be black listed unless and

otherwise justified properly in writing / binding within 15 days of

last notice of penalty.

Addendum/Corrigendum If any Shall be Published 48 Hrs. Price To

the Final Submission Time And Date. The Same Shall From a part Of

Addendum/Corrigendum

17 Tender And The Same As to be Attached Along With The Tender

EPF Act As per Acoount Department circular no-37 Date:09/08/2018

GST will be paid extra by AMC/Authority at prevailing rate to the

Signature of contractor

Add. City Engg.(West Zone)

Name : Ahmedabad Municipal Corporation

Company's Seal :Date :

AHMEDABAD MUNICIPAL CORPORATION

ENGINEERING DEPARTMENT-WEST ZONE

Name of The Work:- Repairing, Renovation and Civil Work as per Requirement at Municipal Building In

S.P.Stadium ward at West Zone.(ARC)

Sr. Rate in Amount

Qty Description of Item Per

Excavation for foundation up to1.5 m depth

including sorting out and stacking of

1a 60.00 useful materials and disposing of Cmt

theexcavated stuff upto 50 Meter

lead.(A) Loose or soft soil

1.5 to 3.0 mt.depth

Excavation for foundation for depth from

m to 5.0 m including sorting out and

stacking of useful materials and disposing

the excavated stuff upto 50 Meter lead.(A)

Loose or soft soil

Excavation for foundation for depth from

m to 3.0 m including sorting out and

d 1.00 stacking of useful materials and disposing Cu.M.

off the excavated stuff upto 50 Meter

lead.(C) Hard Murrum

Filling available excavated earth

(excluding rock) in trenches, plinth, sides of

foundations etc. in layers not exceeding

20 cm. in depth consolidation each 129.10

deposited layer by ramming and watering.

Filling in plinth with sand

underfloors including watering

ramming, consolidating and dressing etc. 455.63

Filling in foundation and plinth with murrum

or selected soil in layers of 20 cm.

4 2.00 thickness including watering, Cmt

ramming and consolidating etc.

Providing and laying cement

concrete1:5:10 (1-Cement: 5-

coarses sand and:10-hand broken stone

5 2.00 aggregates 40mm nominal size) and Cmt

curing complete excluding cost of 2,492.51

formworkin (A) Foundation and Plinth

Providing and laying cement

concrete1:4:8 (1-Cement: 4-

coarses and:8-hand broken stone

6 1.00 aggregates 40mm nominal size) and Cmt

curing complete excluding cost of

formworkin (A) Foundation and Plinth

Providing and laying cement concrete 1:3:6

(1-Cement : 3- coarse sand : 6- hand

broken stone aggregates 40 mmnominal

size) and curing complete excluding cost of 2,956.44

formwork in (A) Foundation and Plinth..

Providing and laying cement

concrete 1:3:6 (1-Cement:3-coarse sand:6-

hand broken stone aggregates

20mm nominal size) and curing complete 4,006.15

including cost of formwork in (A) wall

caps/coping (upto 10 ton)..

Providing and laying cement

concrete work 1:2:4 ((1-Cement:2- coarse

sand:4-graded aggregates 20mm

nominal size) curing complete

excluding cost of formwork and

Foundations, footings, base or

columns and mass concrete 3,923.53

Slabs, landing, shelves, balconies, lintels,

b 1.00 beams, girders and cantilivers upto Cmt

floor two level

Independent piers, columns, and pillars,

upto floor two level 4,012.47

Provdg. & laying cement concrete 1:2:4

(1 cement : 2 coarse sand : 4 graded stone

aggregates 20 mm nominal size) for

reinforced concrete chhajjas not

exceeding 10 cm. thickness upto floors

10 1.00 two level including finishing the Cu.M.

exposed surfaces with cement mortar

1:3 (1 cement : 3 find sand) to give a

smooth and even surface centering and

form work and curing complete

excluding cost of reinforcement.

Providing and laying controlled cement

M.150 for curing complete excluding cost of

11 1.00 formwork and reinforcement for reinforced Cum

concrete work in (A) Foundations, 3,871.39

footings,Base of

columns and Mass concrete

Providing and laying in position Ready

Mixed M-150 grade concrete for

reinforced cement conctere work,

using cement content as per approved

Design Mix manufactured in fully

automatic batching plant and

transported to site of work intransit mixer

for a lead up to 10 kms having

continuous agitated mixer, manufactured

as per mix design of specified grade for

reinforced cement concrete work

11A 1.00 including pumping of R.M.C. from Cmt

transit mixer to site of laying, excluding

the cost of centering shuttering

finishing and reinforcement

including cost of admixtures

inrecommended proportions as per

IS:9103 to accelerate/ retard setting

of concrete, improve work ability without

impairing strength and durability as per

direction of theEngineer-in-charge. Without

Fly Ash (Min cement level as per latest

IS456 shall be maintained)

Providing and laying in position Ready

Mixed M-200 grade concrete for

reinforced cement conctere work,

using cement content as per approved

Design Mix manufactured in fully

automatic batching plant and

transported to site of work intransit mixer

for a lead up to 10 kms having

continuous agitated mixer, manufactured

as per mix design of specified grade for

reinforced cement concrete work

12 1.00 including pumping of R.M.C. from Cmt

transit mixer to site of laying, excluding

the cost of centering shuttering

finishing and reinforcement

including cost of admixtures in

recommended proportions as per IS:9103

to accelerate/ retard setting of

concrete, improve work ability without

impairing strength and durability as per

direction of theEngineer-in-charge. Without

Fly Ash (Min cement level as per latest

IS456 shall be maintained)

Providing and laying controlled cement

M.200for curing complete excluding cost of

12a 10.00 formwork and reinforcement for reinforced Cum

concrete work in (A) Foundations, 3,977.88

footings,Base of

columns and Mass concrete

Walls, from top of foundation level upto

floor two level 4,484.17

Slabs,landing,shelves,Balconies Lintels,

c 10.00 Beams, Girders and Cantilever upto floor Cum

Columns, Pillars posts and struts upto floor

d 10.00 two level. Cum

Staircases excluding landing upto floor two

Vertical and Horizontial its upto floor two

f 1.00 level. Cum

Providing and laying in position Ready

Mixed M-250 grade concrete for

reinforced cement conctere work,

using cement content as per approved

Design Mix manufactured in fully

automatic batching plant and

transported to site of work intransit mixer

for a lead up to 10 kms having

continuous agitated mixer, manufactured

as per mix design of specified grade for

reinforced cement concrete work

including pumping of R.M.C. from

transit mixer to site of laying, excluding 4,853.56

the cost of centering shuttering

finishing and reinforcement

including cost of admixtures in

recommended proportions as per IS:9103

to accelerate/ retard setting of

concrete, improve work ability without

impairing strength and durability as per

direction of theEngineer-in-charge. Without

Fly Ash (Min cement level as per latest

IS456 shall be maintained)

(Cement level 450 kg )

Providing and laying controlled cement

concrete M.250 and curing complete

13A excluding the cost of formwork and

reinforcement for reinforced concrete work

Foundations, footings, Base of columns

B 1.00 and Mass concrete. Cu.M.

Walls, from top of foundation

C 1.00 level upto floor two leve Cu.M.

Slabs,landing,shelves,Balconies, Lintels,

D 1.00 Beams, Cu.M.

Girders and Cantilever upto floor two level.

Columns, Pillars posts and

E 1.00 struts, upto floor two level. Cu.M.

Providing and laying in position Ready

Mixed M-300 grade concrete for reinforced

cement conctere work , using cement

content as per approved Design Mix

manufactured in fully automatic batching

plant and transported to site of work in

transit mixer for a lead up to 10 kms having

continuous agitated mixer, manufactured as

per mix design of specified grade for

reinforced cement concrete work including

pumping of R.M.C. from transit mixer to site

laying, excluding the cost of centering

shuttering finishing and reinforcement

including cost of admixtures in

recommended proportions as per IS:

to accelerate/ retard setting of

concrete, improve workability without

impairing strength and durability as per

direction of the Engineer - in - charge.

Without Fly Ash (Min cement level as per

shall be maintained)

Providing and laying in position Ready

Mixed M-350 grade concrete for reinforced

cement conctere work , using cement

content as per approved Design Mix

manufactured in fully automatic batching

plant and transported to site of work in

transit mixer for a lead up to 10 kms having

continuous agitated mixer, manufactured as

per mix design of specified grade for

reinforced cement concrete work including

pumping of R.M.C. from transit mixer to site

laying, excluding the cost of centering

shuttering finishing and reinforcement

including cost of admixtures in

recommended proportions as per IS:

to accelerate/ retard setting of

concrete, improve workability without

impairing strength and durability as per

direction of the Engineer - in - charge.

Without Fly Ash(Min cement level as per

shall be maintained)

Providing and Laying ordinary cement

concrete 1:2:4 (1-Cement 2-coarsesand:

4-graded stone aggregates 20 mm

nominal size) and finishing smooth with

15a 1.00 curing etc. complete including the cost of Cum

form work but excluding the cost of

reinforsement for R.C.C work in (iv)

Slabs having more than 13 cm and upto

Providing and Laying ordinary cement

concrete 1:2:4 (1-Cement 2-coarsesand:

4-graded stone aggregates 20 mm

nominal size) and finishing smooth with

15b 1.00 curing etc. complete including the cost of Cum

form work but excluding the cost of

reinforsement for R.C.C work in (iv)

Slabs having more than 8 cm and upto

Providing and laying ordinary cement

concrete 1:2:4 (1- Cement 2- coarse sand :

4- graded stone aggregates 20 mm nominal

size) for R.C.C lintel including finishing

15c 1.00 smooth with,curing etc. complete including Cum

the cost of formwork but excluding the cost

of reinforcement.

Brick work using common burnt clay

building bricks having crushing

strength not less than 35kg./Sq.Cm.in

foundation and plinth in Cement

Mortar1:5 (1-Cement :5 - fine

(A) Conventional (upto 10 ton)

Extra Rate for brickwork in Above

17 Item for super structure above plinth

level upto floor two level (B) Conventional

(A) Conventional (upto 10 ton)

C) above floor two level Item No. 2(6.13) Per

c 1.00 (A) Modular Floor Per

D) above floor two level Item No. 2(6.13) Per

d 1.00 (B) Conventional Floor Per

Half brick masonry in common brunt

clay building bricks having crushing

strength not less than 35 Kg/Sq.Cm. in

18 1.00 Cement mortar 1:4 ( 1-Cement : 4 coarse Smt

sand ) in foundation and 593.90

Plinth conventional brickwork (up to

ton) (B) Conventional

Extra for half brick masonry in super

19 1.00 structure above plinth level upto floor Smt

two level (B) conventional

Providing and laying Pre cast Light weight

concrete hollow core wall with hollow

core concrete unit of approved make &

size of 92 mm thick, 600 mm wide and

mm/ 3300 mm in legth made from of

controlled cement concrete M20 having 747.00

cube compressive strength not less than

20 MP a jointing with high strength &

tensile adhesion non-shrink

cementitious joint compound /P.U.

Foam. (Plaster not required)

Providing and laying Pre cast Light weight

concrete hollow core wall with hollow

core concrete unit of approved make &

size of 120 mm thick, 600 mm wide and

mm/ 3300 mm in legth made from of

controlled cement concrete M20 having 842.00

cube compressive strength not less than

20MP a jointing with high strength &

tensile adhesion non-shrink

cementitious joint compound/ P.U.Foam.

(Plaster not required)

Providing and laying Pre cast Regular

concrete hollow core wall with hollow

core concrete unit of approved make &

size of 92 mm thick, 600 mm wide and

mm/ 3300 mm in legth made from of

controlled cement concrete M35 having 777.00

cube compressive strength not less than

35 MP a jointing with high strength &

tensile adhesion non-shrink

cementitious joint compound/ P.U.Foam.

(Plaster not required)

Providing and laying Precast

Regular concrete hollow core wall with

hollow core concrete unit of approved

make & size of 120 mm thick, 600 mm wide

and 2400 mm/ 2600 mm/ 2850 mm/

mm/ 3300 mm in legth made from of

controlled cement concrete M35 having 875.00

cube compressive strength not less than

35 MP a jointing with high strength &

tensile adhesion non-shrink

cementitious joint compound /P.U.Foam.

(Plaster not required)

Providing form work in ordinary timber

planking so as to give a rough finish

including centering, shuttering, strutting

and propping etc. height of propping

24 and centering below supporting floor to

celling not exceeding 4 M & removal

of the same for in situ reinforced or

plain concrete work upto floor four level

Foundation, footings, bases of

a 1.00 columns etc. and mass concrete. Smt

(B) Flat surfaces such as soffits of

supspened floors slabs Landings and the

like. (1) Floors etc. upto 200 mm in 252.00

(B) Flat surfaces such as soffits of

suspended floor roof slabs Landings and

the like. (2) Floors etc. above 200mm in 270.90

Vertical surface such as walls (any

thickness) partitions and the like including

attached buttresses & string course & the 229.95

(ii) Sides And Soffits Of Beam,

Haunchings Cantilevers, Girders,

e 1.00 Bressumers And Lintels Not Smt

Exceeding 1 M In Depth.

(G) Columns PillarsPosts and struts. (1)

f 1.00 Square Rectangular Polygonal in plan. Smt

(2) Circular or curved in plan.

(H) (2) Sides and soffits of Beams Beam

Haunchings canti-levers Girders

Bressumers and Lintels exceeding 1M.in 192.15

Providing and fixing 35 mm thick

shutters for Doors, windows and clear

25 story windows including anodised

alluminium butt hinges with necessary

(A) Indian Teak Wood (ii) Fully

Glazed. 4,788.50

(B) Indian Teak Wood (ii) Fully

Panelled 5,478.89

(C) Indian Teak Wood (iii) Partly

panelled and partly glazed. 5,133.69

Providing and fixing 35 mm thick

shutters for Doors, windows and clear

26 story windows including black enamelled

M.S.butt hinges with necessary screws.

(A) Indian teak wood. (i) Fully

Panelled.(upto 10 ton) 5,285.45

(A) Indian teak wood. (ii) Fully

Glazed.(upto 10 ton) 4,595.06

(A) Indian teak wood. (iii) Partly panelled

c 1.00 and partly glazed. (upto 10 ton) Smt

Providing and fixing 35 mm thick

panelled, glazed or panelled and glazed

shutters for Doors windows and clear story

windows including anodised alluminium

But hinges with necessary screws and

indian teak wood shutters with.

(A) Plywood sheet panels.

(B) Particle board panels

(C)Hard board panels.

(D) Asbestos sheet panels.

Providing and fixing 25 mm thick

shutters for cup boards etc.

including black enamelled M.S. butt

hinges with necessary screws.(A) Indian 3,006.75

teak wood. (i) Fully Panelled. (upto

Providing and fixing 25 mm thick shutters

for cupboards etc. including anodised

butt hinges with necessary screws. (A) 2,594.74

Indian teak wood. (ii) Fully Glazed.

Providing and fixing 25 mm thick shutters

for cupboards etc. including anodised

b 1.00 alluminium butt hinges with necessary Smt

screws. (A) Indian teak wood. (ii) Partly

panelled and partly glazed.

Providing and fixing plain asbestos cement

sheet 6 mm thick in partitions

including fixing to fames with screws etc,

complete with 50 mm x 12 mm 827.20

Deodar wood beading (Frames to

be paid separately) (upto 10 ton)

Providing and fixing in partitions 4 mm

thick medium hard board of approved

quality including fixing to fames with

screws etc complete with 50 mm x 12 516.60

mm teak wood beading (Frames to

be paid separately) (upto 10 ton)

25 mm thick wooden shelves

supported on 40 x 40 mm x 6 mm T or L

iron brackets fixed at suitable

distances but not exceeding 75 1,306.61

cm. apart with Mango wood or

equivalent quality. (upto 10 ton)

40 mm thick wooden shelves

supported on 40 x 40mm x 6 mm T or L iron

brackets fixed at suitable distances not

exceeding 75cm. Apart with Mango 1,691.00

wood or equivalent quality. (upto 10 ton)

Providing and fixing M.S. round or square

bars with M.S. flats at required spacing

33 1.00 in wooden frames of windows and kg

clerestory windows.(upto10 ton)

Providing and fixing M.S. grills of

required pattern to wooden frames of

windows etc. with M.S. flats at required

34 1000.00 spacings and frame alround, square or kg

round bars with round headed bolts and

nuts or by screws (A) Plain Grill. (upto

Providing and fixing M.S. grills of

required pattern to wooden frames of

windows etc. with M.S. flats at required

a 1.00 spacings and frame alround, square or kg

round bars with round headed bolts and

nuts or by screws (A) Ornamental Grill.

Providing and fixing glazed louvered

glass windows and ventilators with

teak wood frame 10 cm. x 7 cm. size

including 3 coats of oil painting to wood 4,102.54

work etc.complete. (upto 10 ton)

Providing and fixing glazed louvered

glass windows and ventilators with

teak wood frame 10 cm.x7 cm. size

36 1.00 including 3 coats of oil painting to wood Smt

work etc.complete.with wooden louvers 4,332.47

plank 12mm thick (upto 10 ton)

Providing and fixing 35 mm thick

shutters for Doors, windows and clere

story windows including Indian teak

wood frames 10 cm x 7 cm. size

including anodized alluminium fixtures 3,211.96

and fastenings including primer coat of

approved quality and two coats of oil

painting etc, complete.(ii) Fully Glazed.

Providing and fixing 35 mm thick

shutters for Doors, windows and clere

story windows including Indian teak

wood frames 10 cm x 7 cm. size including

38 2.00 black enamelled iron oxidixed Smt

fixtures and fastenings including primer

coat of approved quality and two coats of

oil painting etc, complete.(ii) Fully

Providing and fixing 35 mm thick shutters

for Doors, windows and clerestory windows

including Indian teak wood frames 10 cm x

7 cm. size including anodized alluminium

a 2.00 and fastenings including primer coat of Smt

approved quality and two coats of oil

etc, complete. (iii) Partly panelled and partly

Providing and fixing 30mm thick FACTORY

SOLID BOTH SIDE PRELAM PANEL PVC

SHUTTER consisting of frame made out of

M.S.tubes of 19 gauge thickness and size

of 19mm x 19mm for stiles, top and bottom

rails. M.S. frame shall have a coat of steel

primer of approved makde

and manufactures. M.S frame covered with

5mm thick heat moulded prelim PVC ‘C’

channel of siz 30mm thickness, 70 mm

width of which 50mm shall be flat and

20mm shall be tapered in 45 degree Angle

on either side forming stiles, and 5mm thick,

95mm wide pream PVC sheet out of which

75mm shall be flat and 20mm shall be

tapered in 45 degree on the inner side ot

form top and bottom rail and 115mm wide

prelim PVc sheet out of which 2,214.00

75nmm shall be flat and 20mm shall be -

75nmm shall be flat and 20mm shall be

tapered on both side to form lock rail, Top,

and lock rails shall be provided either side

of the panel. 10mm (5mm x 2) thick 20mm

wide cross PVC sheet shall be provided as

gap insert for top rail and bottom rails.

Panelling of 5mm thck both side prelim

PVC sheet to be fitted in the M.S. frame

welded,sealed to the stiles and rails with

7mm (5mm + 2 mm) thick x 15mm wide

PVC sheet beading on inner side, and

joined togeth with

solvent cement adhesive. An additional

5mm thick PVC strip of 20mm width is to be

stuck on the interior side of the ‘C” chanel

using PVC solvent adhesive etc. complete

as per direction of Engineering in charge,

manufacture’s specification and rawing.

Providing and fixing in position

collapsible steel shutters with vertical

channels 20 x 10 x 2 mm braced with

flat iron diagonal 20 x6 mm size with top

40 20.00 and bottom rails T iron 40 x 40 x 6 mm with Sq.M.

38 mm dia steel pulleys complete with

bolts, units, locking arrangements,

stoppers, handles, including a priming

coat of red lead paint & approved make.

Providing and fixing 1 mm thick M.S.

sheet sliding shutters with frame and

diagonal braces of 40x40x6 mm angle

iron, 3.15 mm M.S.gusset plates at

Junctions and corners 25 mm dia.

41 1.00 pulley, 40x40x6 mm angle and T-iron Sqm

huide rail at top and bottom

respactively with handles, stoppers and

locking agangement etc, including

applying a priming coat of red lead paint.

Providing and fixing rolling shutters of

approved make made of 80 mm wide

M.S.laths inter-locked together through

their entire length and jointed together at

theends by end locks mounted on

specially designed pipe shaft with

bracket plates, guide channels 3,468.72

and arragements for inside and out

side locking with push-pull

operation including the cost of hood

cover and spring etc. complete. (A)

Shutters having width below 3.5 M.

Providing and fixing rolling shutters of

approved make made of 80 mm wide

M.S.laths inter-locked together through

their entire length and jointed together at

theends by end locks mounted on

specially designed pipe shaft with

bracket plates, guide channels 4,450.51

and arragements for inside and out

side locking with push-pull

operation including the cost of hood

cover and spring etc. complete. (A)

Shutters having 3.5 M. & Above

Providing and fixing extruded aluminum

window having extruded aluminum Colour

Powder Coated section frame main outer

size 127mm x 38.10mm x

1.35mm ,@ Wt.1.384 Kg/mt,horizontal Four

track member size 122.20mm x 31.75mm x

1.10mm @ Wt. 1.205 Kg/mt,vertical

member of size 122.20mm x 31.75mm x

1.50mm ,@ Wt. 1.398 Kg/mt with sliding

43 1.00 shutters of horizontal member size 40mm x Smt

0.456Kg/mt,vertical member of size 40mm x

with 5 mm thick transparent bronze colour

tinted float glass with powder coated

aluminum fittings and fixtures and

transparent silicon sealant glass fixing to

frame as per details etc complete for

Providing and fixing window having

extruded aluminum Colour anodized

section frame main outer size 63.50 x

x 1.95 mm,@ Wt 1.094 Kg / Rmt, horizontal

two track member size 61.85 mm x

mm x 1.20mm @ wt.of 0.695 Kg/mt, vertical

member of size 61.85 mm x 31.75mm x

1.30 mm @ wt.of 0.659 Kg/mt with sliding

shutters of horizontal member size 40mm x

vertical member of size 40mm x 18mm x

Kg/mt with 5 mm thick transparent bronze

colour tinted float glass with powder coated

aluminum fittings

and fixtures and transparent silicon sealant

glass fixing to frame as per details etc

complete for window.

Providing & Fixing in position

Alluminium vents with frame using

approved anodised extruded

alluminium section as approved by Engg.

In charge.(Jindal alluminium) units

45 10.00 equivalent Approved Rate)Frame section Sq. M.

0.68Kg/Rmt) incl. Providing & Installing

mmthick approved color Acrylic sheet of

standard quality etc. comp.

Providing and fixing standared

extruded of alluminium section of size

63 mmx38.10 mmx1.2 mm (Jindal

46 1.00 Section:2434, @ Wt.0.643 Kg/mt) with Sq. M.

colour anodized alluminium frame for 1,163.92

ventilation with 5 mm thick frosted glass

as details etc complete for Ventilation

Providing and fixing standared extruded of

alluminium section of size 63.50 x 38.10 x

mm,@ Wt 1.094Kg / Rmt with colour

Powder Coated alluminium frame with 5 1,509.90

mm thick transparent bronze colour tinted

float glass as details etc complete for Fix

Providing and laying 40 mm thick marble

chips flooring rubbed and polished

(I.E.terrazo) to granolithic finish with under

layer 30 mm thick cement concrete1:2:4

(1-Cement: 2-coarse sand: 4-graded

stone aggregate 10 mm and down

gauge) and to player 10 mm thick with

white, black or white and blak marble cihps

48 1.00 of required sizes from 1 mm to 4 mm Sqm

nominal size laid in cement marble powder

mix 3:1 (3- Cement:1-Marble powder

by weight) in proportion of 4:7 (4-

Cement: 7-marble chips by volume)

(C) Medium Shade pigment with

approx 50% white cement and 50%

ordinary cement (In top layer only) (upto

Providing and laying marble chips

skirting (Terrazo) or dedo rubbed, and

polished to Granolithic finish to player

mm white, black or white and black

marble chips of size from smallest to

49 1.00 4 mm nominal size laid in cement marble Sqm

powder mix 3:1 (3-Cement:

marble powder by weight) in proportion of

4:7 (4-cement marble powder mix: 7-marble

chips by volume) (B) Light shade pigment

with white cement (In top layer only)

Providing and laying white glazed tiles 6mm

thick in flooring treads of steps and landing

laid on a bed of 12mm thick cement mortar

1:3 (1-cement : 3-coarse sand ) finishing 908.17

with flush pointing in white cement.

Providing and laying Ceramic tiles 6 mm

thick in flooring treads of steps and

landing laid on a bed of 12 mm thick

cement mortar 1:3 (1- cement :3-coarses 960.47

and) finishing with flush pointing in white

cement. (upto 10 ton)

Providing & Fixing 2mm Aluminium /

4mmACP sheeting fixed with Type-11

Class-C High Intensity Grade Sheeting as

per IRC 67 : 2012 reflective sheeting of size 5,832.20

including lettering and signs as

Providing and laying Vitrified tiles 8 to

mm thick, 36''x36'' in flooring treads of steps

and landing laid on a bed of 12 mm

thick cement mortar 1:3 (1-cement:3- 1,469.91

coarses and) finishing with flush pointing

inwhite cement. (upto 10 ton)

Providing and laying Vitrified tiles 8 to

mm thick, 24''x24'' in skrting risers of steps

and dedo on 10 mm thick cement

plaster 1:3 (1- cement: 3-coarse 1,062.50

sand) and jointed with white cement

slurry (upto 10 ton)

Providing and laying Vitrified tiles 8 to

mm thick, in skrting risers of steps and

dedo on 10 mm thick cement plaster

1:3 (1-cement:3- coarse sand) and 1,523.61

jointed with white cement slurry (upto

Providing and laying 24" x 24" vitrified

Tiles 8 to 10 mm th. Double

Charged gloosy/ Matt of Approved make

as approved by Adl.C.E. / consultants

56 1.00 in flooring over 20 mm thick cement Sq. M.

mortar 1:6 (1 cement : 6 coarse

sand)on new surface& jointed with colour

cement slurry incl with flush pointing

& cleaning the surface etc. comp.

Providing and laying 24" x 24" vitrified

8 to 10 mm th.Double Charged

Gloosy / Matt tiles of Approved make

as Approved by Adl.C.E. / Consultants for

upto 10 cm high skirting as approved by

57 1.00 Engineer in charge over 10 mm thick Rmt

cement mortar 1:6 (1 cement : 6 coarse

sand)on new surface& jointed with colour

cement slurry incl with flush pointing &

cleaning the surface etc. comp.

Providing and laying polished Kota stone

slab flooring over 20 mm (Average)

thick base of cement mortar 1:6 (1-

cement:6-coarses and) or L.M.1.1.5

58 200.00 (1-Lime putty:1.5-coarses and) laid over Sq.M.

and jointed with grey cement slurry mixed

with pigment to match the shade of

slab including rubbing and polishing etc.

complete. (A) 25 mm thick (upto 10 ton)

Providing and laying marble stone slab

flooring over 20mm (average)base of

cement mortar 1:6 (1-cement : 6 coarse

sand) or L.M. 1:1.5(1- lime putty : 1.5 -

59 1.00 coarse sand) laid and jointed with gray Sq.M.

cement slurry including rubbing and

polishing complete. (A) Marble slab 25mm

Providing and laying polished Kota stone

slab flooring over 20 mm (Average)

thick base of cement mortar 1:6 (1-

cement:6-coarses and) or L.M.1.1.5 laid

over and jointed with grey cement 1,085.48

slurry including rubbing and polishing

etc.complete. (B) 30 mm thick (upto

Providing and laying polished kota stone

slab 25 mm thick in risers of steps, skirting

Dedo and pillars laid on 10 mm thick

cement mortar 1:3 (1-Cement :3 coarses

61 1.00 and) and jointed with gray cement Sq.M.

slury mixed with pigment to match the

shade of slab including rubbing and

polishing etc.complete. (upto 10 ton)

Providing and laying cement

concrete flooring 1:2:4 (1-cement: 2-

coarses and:4-graded stone aggregate

20mm nominal size) laid in one layer and 297.68

finished with a floating coat of neat

cement. (A) 40mm thick. (upto 10 ton)

Providing and laying cement

concrete flooring 1:2:4 (1-cement: 2-

coarse sand:4-graded stone aggregate

20mm nominal size) laid in one layer and 348.08

finished with a floating coat of neat

cement. (B) 50mm thick. (upto 10 ton)

Providing and fixing pre-cast

concrete kerb stone of gray cement

based concrete block 30 cm length,

cm height and 15 cm thick of M200 grade

64 1.00 concret as per approved design and Rmt

including excavation for fixing in proper line

and level, filling the joint with C:M 1:3 (1

cement :3 fine sand) etc complete. (upto

Providing and fixing pre-cast Rubber Dye /

steel Dye inter locking concrete block

with grade of concrete M300 pnumatic

compressed / vibrated mechanically and as

approved design Confirming to IS 15658 : 680.10

2006 including 35 mm Sand layer for

and filling the joint with sand in proper line

and level as per guidlines of IRC : SP 63-

2018 etc. Complete.

Providing and laying broken china mosaic

flooring for terrace using 12 mm to 20 mm

broken pieces of glazed tiles to be laid over

cement mortar 1:3 to plain or slope and to

be tempered to bring mortar creme out

66 200.00 upto surface using white cement Sqm

including rounding off junctions and

extending them up to15 cm along the

wall, clearing with water and oxalic

acid etc.asdirected.

Providing and laying coloured glazed

tiles of the size 300 mmx200 mmx8

mm/300 mmx450 mmx8 mm in skirting,

67 10.00 risers of steps and dedo on 10 mm. Sqm

thick cement plaster 1:3 (1cement: 3 1,426.95

coarse sand) & jointed with white

Providing corrugated G.I. sheet of class-

3 roofing fixed with glavanished

iron J or L Hooks, Bolts and nuts 8 mm

diameter with bitumen and G.I. limpet

68 1.00 washer or G.I. limpet washer. filled with Sqm

white lead complete excluding the cost of

purlins, Rafters and Trusses. (1) 0.80 mm

thick sheet.(up to10 ton)

Providing ridges or hips 600 mm over

allin plain G.I. sheet class-3 fixed with

69 1.00 G.I. J or L Hooks and nuts 8 mm dia Sqm

G.I. Limpet and bitumen washer complete.

Providing and fixing 150 mm wide 450 mm

over all semi circular plain G.I.sheet class-

3 gutter with Iron brackets 40 mmx3 mm

size Bolts, Nuts, washers etc. 555.71

including making necessary connection with

rain water pipes. (i) 0.80 mm thick

Providing and fixing five courses water

profing treatment with bitumen felt

consisting of second and fourth course

of blown/ bitumen or/and residual

bitumen applied hot at 1.2 kg.per

Sq.M.of area for each course and

first course with fibre base bitunen

71 1.00 saturated under lay type land third course Sqm

with fibre base self finished felt type

grade 1 and fifth and final course of

stone grit 6 mm and down size or pea

sizes gravel spread at

0.008 Cu.Metre/Sq.metre preparation of

surface excluding grading complete. (upto

10 ton) including

Providing and fixing on wall face C.I.

Rain water pipe including filling the joints

with spun yarn soaked in neat cement

slurry and cement mortar 1:2(1- 283.62

Cement : 2-fine sand) (A) 75 mm dia.

Providing 15 mm thick cement plaster

in single coat on Rough (Similar) side of

single or half brick walls for interior

plastering up to floor two level and 174.83

finished even and smooth in (i) Cement

mortar 1:3 (1-cement :3-sand)

Providing 20mm thick sand faced cement

plaster on walls upto height 10 metres

above ground level consisting of 12mm

thick backing coat of C.M. 1:3 (1-cement : 215.78

3-sand) and 8mm thick finishing coat of

C.M. 1:1 (1-cement : 1-sand) etc. complete.

Colour washing with lime on wall surface

(two coats) over and including a

primary coat of white washing to give an

even shade after through brooming the 12.29

surface to remove all dirt, dust,

mortar drops and other foreigh matter.

Removing dry or oil bound

distemper by a washing and

76 2.00 scraping and sand papering the wall Sqm

surface smooth including necessary

repairs to scratches complete.

Distempering with dry distemper of

approved brand and manufacture (two

coats) and of required shade on wall

surfaces of given an even shade, over

and including a priming coat of 46.94

whiting after thoroughly brooming the

surface free from mortar dropping and

other foreign matter.

Extra Coat for Above Item over above

77 a 1.00 for every subsequent coat of Sqm

approved brand and manufacture.

Distempeing (Two coats) with oil bound

distemper of approved brand and

manufacture and of required shade on

wall surfaces to give an even shade,

over and including a priming coat

with distemper primer of approved

brand and manufacture after 76.08

thoroughly brushing the surface free

from mortar dropping and other

foreign matter and also including

preparing the surface even and sand

papered smooth.

Extra Coat for Above Item over above

79 2.00 for every subsequent coat of Sqm

approved brand and manufacture.

Wall painting (two coats) with plastic

emulsion paint of approved brand and

manufacture on undecorated wall

80 500.00 surface to give an even shade including Sqm

throughly brushing the surface free 78.44

from mortar droppings and other foreign

matter and sand papered smooth.

Extra over item for every sub sequent

81 5.00 coat of wall painting with plastic emulsion Sqm

paint of approved brand

Extra over item for painting with plastic

81 a 5.00 emulsion paint of approved brand on smt

ceilings and sloping roofs.

Applying priming coat over new steel

and other metel surface after and

including preparing the surface by

throughly cleaning, oil, grease, dirt and

other foreign matter and scoured with 34.34

brushes fine steel wood, scrapers and sand

paper with ready mixed priming paint

brushing red lead.

Painting two coats (excluding priming

coat) on new steel and other metal

surface with enamel paint, brushing,

83 50.00 interior to give an even shade including Sqm

cleaning the surface an even shade 86.94

including cleaning the surface of all dirt,

dust and other foreign matter.

Painting one coats (excluding priming

coat) on previously painted steel and other

metal surface with enamel paint, brushing

to give an even shade including cleaning 54.35

the surface of all dirt, dust and other

foreign matter.

Extra over item for 83 & 84 every sub

sequent coat of paint. 50.40

Painting two coats (excluding priming

coat) on new steel and other metal

surface with synthetic enamel paint,

brushing to give an even shade including 64.66

cleaning the surfaceofalldirt,dust and other

foreign matter.

Painting one coats (excluding priming

coat) on previously printed steel and other

metal surface with synthetic enamel paint,

brushing to give an even shade 43.79

including cleaning the surface of all dirt,

dust and other foreign matter.

Extra over Above item for 86 & 87 for

88 50.00 every sub sequent coat of paint. Sqm

Painting two coats (excluding priming

coat) on external surface of new rain

water, soil, waste and vent pipes and

fittings with ready mixed bituminous

brushing, black, anti corrosive to give 20.16

an even shade including cleaning of all

dirt, dustand other foreign matter.(75 mm

Painting two coats (excluding priming

coat) on external surface of new rain

water, soil, waste and vent pipes and

fittings with ready mixed bituminous

brushing, black, anti corrosive to give 25.05

an even shade including cleaning of all

dirt, dust and other foreign matter.(100 mm

Painting two coats (excluding priming

coat) on new wood and wood based

surface with enamel paint, interior to

give an even shade including

91 1.00 cleaning the surface of all dirt, dust Sqm

and other foreign matter sand papering

and stopping. (a) Ready mixed paint

brushing wood primier pink.

Painting one coats (excluding priming

coat) on previously painted wood and

wood based surface with enamel paint,

92 5.00 to give an even shade including cleaning Sqm

the of all dirt, dust and other foreign 40.17

matter.(b) Ready mixed paintbrushing

priming for enamel

Extra over Above item for 91 &

93 5.00 every sub sequent coat of paint. Sqm

Painting two coats (excluding priming coat)

wood and wood based surface with ready

paint, brushing, oil, gloss, semi gloss to

give and 104.12

even shade including cleaning of all dust,

other foreign matter sand papering and

Finishing wall with weather proof exterior

emulsion paint on wall surface (two

coats) to give an required shape even

95 300.00 shade after thoroughly brushing the Sqm

surface to remove all dirt, and remains

of loose powdered materials.etc

Applying two coats of putty & two coats of

of approved brand and manufacture on new

surface to give an even shade including

thoroughly 40.19

brushing the surface free from mortar

other foreign matter and sand papered

Painting two coats (excluding priming

coat) on new wood and wood based

surface with enamel paint, interior to

97 1.00 give an even shade including Sq.M.

cleaning the surface of all dirt, dust

and other foreign matter sand papering

Writing letter or figures on any

surface with black japan paint (stops,

comas, hyphens and the like not to be

measured and paid for separately) 3.47

(i) Block (Letters/Figures) (Per 10 Letter

Extra over items for using thick white per letter

paint instead of black japan paint. per

(i)Block (Letters/Figures) Cm/Ht

Polishing with french polish on new wood

wood based surface to give an even

surface including cleaning, the surface of all

dirt, dust and 131.67

sand papering smooth and including a coat

Extra over items for using thick white

paint instead of black japan paint. (ii) per letter

Indian (Letters/Figures) 0.07 perCm/Ht

Painting lines, deashes, arrows, letters

etc on roads, Air fields and like in two coats

with road marking paint, brushing

including cleaning the surface of all dirt, 121.91

dust and other foreign matter. (i)Over

Painting lines, deashes, arrows, letters

etc on roads, Air fields and like in two coats

with road marking paint, brushing

including cleaning the surface of all dirt, 12.14

dust and other foreign matter.(ii) Upto

Painting lines, deashes, arrows, letters etc

on roads, Air fields and like in one coats

with road marking paint, brushing including

cleaning the surface of all dirt, dust and 50.40

other foreign matter. (i) Over 10cm in width

Painting lines, deashes, arrows, letters

etc on roads, Air fields and like in one coats

with road marking paint, brushing

including cleaning the surface of all dirt, 5.52

dust and other foreign matter. (ii) Upto

Demolition including stacking of

serviceable materilas and disposal of

106 30.00 unserviceable materials with all lead and Cu.M.

lift. (i) R.C.C. work

Demolition of Brick work and stone masonry

including stacking of serviceable materil

107 30.00 as and disposalof unserviceable materials Cu.M.

with all lead and lift.(ii) In Cement Mortar.

Demolition of terrace including stacking of

serviceable materilas and disposal of

107 A 50.00 unserviceable materials with all lead and Smt

lift.(i) Brick tile covering.

Dismentaling tiled of stone floors laid in

mortar including stacking of serviceable

108 300.00 materil as and disposal of unserviceable Sqm

materials with all lead and lift.

Dismentaling of sheet roofing

including ridges, Hips, Valleys, Gutters

etc. stacking of serviceable materil as

and disposal of unserviceable 47.25

materials with all lead and lift.(i) G.I.sheet

Dismentaling of sheet roofing

including ridges, Hips, Valleys, Gutters

etc. stacking of serviceable materil as

and disposal of unserviceable 53.55

materials with all lead and lift.(i) A.C.

Dismentling steel work including

110 10.00 distempering and stacking the Kg.

materials with all lead and lift.

Dismentling doors, windows,

ventilators etc. (wood or steel) shutters

including chowkhats architraves, hold

111 10.00 fasts and other attachment etc. Each

complete and stacking the material within

all lead and lift.(i) Not exceeding 3 Sq.M. in

Dismentling doors, windows,

ventilators etc. (wood or steel) shutters

including chowkhats architraves,hold

112 10.00 fasts and other attachment etc. Each

complete and stacking the material with

in all lead and lift.(ii) Exceeding 3 Sq.M.in

Dismentling barbed wire in fencing

including making rolls and also

including dismentling fencing posts

including all earth work concrete in base

113 10.00 and making good the disturbed Rmt

ground stacking useful materials as

directed and disposing as directed

and disposing of the unserviceable

materials with all lead and lift.

Dismentling C.I. pipes G.S.W. pipes

abd A.C. rain water pipes with fittings

114 1.00 and clamps including stacking the Rmt

materials with all lead and lift (for any dia, of

Dismantling santtary fittings like wash

basin . W.C. pan Indian and Europe an

115 10.00 type, flushing tank etc. including Each

stacking the materials with all lead and

Scraping oil paint from steel and other

116 10.00 metal surface and making the surface Smt

even (with Hand Scraping.)

Removing and scraping of old

deteriorated plaster of any

thickness from wall / R.C.C member

including stacking of serviceable 19.38

material and disposal of unserviceable

from site of work with all lead and lift

Providing and fixing M.S. fan clamps

of shape and size as specified in

118 1.00 existing R.C.C. slab including cutting Each

chase and making good.

Cutting out cracks of roof terrace to V-

section, cleaning out, wetting, grouting

119 1.00 with cement and sand slurry 1:3 (1- Rmt

cement 3-sand ) (upto 10 ton)

Cutting out cracks roof terrace to V-

Section cleaning out and filling solidly

120 1.00 with a hot mixture of bitumen and Rmt

clean dry sand (1:1 by weight) (up to

Providing & Fixing in position

Alluminium doors with frame using

approved quality anodised

extruded alluminium section as

approved by Engg.in charge(Jindal

alluminium)(a) Frame sections

101.6x44.45 mm (b) Shutter bottom

vertical & top section 83.5x44.45

(wt.1.31 kg/mt.)(at 1.31 kg/mt) (c) Shutter

bottom section at 114.3x44.45 mm at (1.37 2,900.00

kg/mt) Shutter middle section at 100x44.3

wt.(1.37 kg/mt) incl.providing & installing

5 mm thick approved color Acrylic

sheet of standard quality fixed with

glazing chips on upper pannel &

Laminated sheet on lower pannel

(wtt.0.13 kg/Rmt) etc.comp.as direction

of engg.in charge.(N.S.)

Providing & Fixing in position Fully Panelled

/ Partly Panelled Partly Glazed / Fully

Glazed Alluminium doors with frame

using approved quality anodised

extruded alluminium section of 1.5 mm

thickness as approved by Engg. In

charge.(Jindal alluminium )(a) Frame

sections 101.6x44.45 mm b) Shutter

vertical & top section 83.5x44.45

Shutter bottom section at 114.3 x44.45mm

at ( 1.37 kg/mt ) Shutter middle section

at 100x44.3 wt. (1.37 kg/mt ) incl.

providing & installing 5 mm thick Glass

of standaed quality fixed / 12 mm

thick Laminated sheet with glazing chips

(wt. 0.13 kg/ Rmt) in panels etc. comp.

as per Detail Given & direction of

engg.in charge.

Providing & Fixing in position

Alluminium window 2/3/4 track sliding

/ fix type with frame using approved

anodised extruded alluminium section of

minium thickness of 1.5 mm as approved by

Engg. In charge.(Jindal 4,518.00

alluminium) units equivalent.

including P/F installing 5 mm thick

clear/tinted Glass of standard quality

Providing and fixing standared extruded of

alluminium section of size 63.50 x 38.10 x

1.95 mm,@ Wt 1.094Kg / Rmt with colour

124 1.00 Powder Coated alluminium frame with Sq. M.

5 mm thick transparent bronze colour tinted 1,815.14

float glass as details etc complete for Fix

Providing and fixing of Ridge

flashing for roof panel shall be made

out of 0.5 mm thick pre coated GI

sheet. The Pre coatedsheet shall be of

minimum 240 mpa steel grade

confirming to IS 14246:1995 and shall

have zinc coating of minimum 120 gsm

as per IS:277:1992, 5-7 microns

epoxy primer on both side of the sheet

and polyester top coat 15-18 micron. The 458.85

PP GI Sheet shall have plastic

protective guard film of minimum

microns to avoid scratches during

transportation. The ridge shall be fixed to

the steel members by poprivetor self

drilling/self stitching fastners @

maximum 450mm c/c along length of

capping/flashing etc complete .

Supplying and fixing vinyl flooring over

the surface having 1-2 mm thickness

126 1.00 as per directed by engineer Smt

incharge etc as completed (N.S.)

Providing and laying 15mm

bamboza wooden flooring as per

architect's drawing with all

necessary details as directed by the

project consultants. Use underlay for 2,690.00

better result as per Detail specifications

and directed by the project consultants.

(N.S.) Approved Rate )

Providing and fixing 1.20 Metre high

fencing with 2.0 Metre long M.S. Angle

posts 40 mm x 40 mm x 6 mm and oil

painting 3 coats fixed at 2.5 Mt, C/c.

with five Horizontan lines and two

128 1.00 diagonals of galvanised steel barbed Rmt

wire weighting 9.38 Kg. per 100 Metre,

strained and fixed to posts with G.I,

staples including fixing the posts in

ground with 0.5 M x 0.5.M x 0.5 M. block

in C.C 1:5:10 etc complete.

Dismentling barbed wire in fencing

making rolls and also including dismentling

posts including all earth work concrete in

129 1.00 making good the disturbed ground stacking Rmt.

materials as directed and disposing as

disposing of the unserviceable materials

Constructing a sink (chowkedi) with

C.C. 1:2:4, 12 cm. thick over B.B.

masonry in C.M, (1:6) in front and dwarf

130 1.00 wall 1.0 Mt. high and 23 cm. thick Rmt

cement plaster to masonry / in C.M.1:3) 2,235.66

and cement concrete flooring in 1:2:4:

mix 5cm.dia.drain pipe etc.complete.

Constructing a cooking platform 60 cm.

width and 70 cm high resting on B.B.

Masonry walls 23 cm. thick in C.M. (1:6)

with (i) Fixing or precast R.C.C. 1:2:4)

8 cm. thick slab with marble chips set in 933.98

C.M. (1:6) (6 mm thick terrazo) with

plastering on exposed faces walls in

C.M. (1:4) etc complete.

Making 15 mm groove in RCC work on road

and filling it with polysulfied selant and

132 1.00 finished it good incl. all all labour charges Rmt

etc. comp as directed

P/A Tremix with dewartering

machine and floater machine on

constructed CC work for finishing the

surface as per requirement. The rate

including all machinaries, labor, 54.00

loading, unloading, transportaion etc

complete as per direction given by

engineer incharge.

Carring out timber treatment to all wood

work including drilling holes and spraying

oil based chemical solution on surface of

timber work for termite control including

labour and material etc. complete. Using

Chlordene 20 EC. As Per

6113_part III Consentration Weight1.00

134 1.00 percent is recommended one litre chemical Smt

emulsion dillute with 9 liter of

kerosene precent concentration.

Total dillute concrentration will be

10 litre inclusive of the litre

chemical emulsion appication 0.75 /

Litre chemical per one Sqmt printed two

coat wood surface.

Applying general insecticide pest control

treatment to floors, cup boards etc

including labour material etc.

complete. Using Heptachloride 20 EC.

As Per 6113_pests Consentration

Weight 0.50 percentis recommended one

litre chemical emulsion dillute with 39 liter 88.40

of water will give. Total dillute

concrentration will be 40 litre inclusive of

one litre chemical emulsion appication

0.5 Litre chemical / Sqm of surface

is recommended as per I.S

Carring out plinth treatment to post

construction / existing structure by spraying

chemical solution for termite control

treatment including labour and material

consist ment with I.S. specification.

Using Chlordene and Chior purfiles

136 1.00 EC. As Per 6131_paret-II Smt

Consentration Weight on percentis 104.90

recommended i.e one litre 20 EC

chemical emulsion with 19 liter give

1% concrentration inclusive of one litre

chemical emulsion appication attherate

of 5 Litre chemical / Sqm of surface

is recommended as per I.S

Carrying out wall treatment for termite

control including spraying with chemical

solution in oil base (0.5 Lit./Sq.M.)

including labour and material Using

Hepachlor concentration 20 EC. As

Per IS.6316_paret-II Consentration by

Weight 0.50 percentis

137 1.00 recommended i.e one litre Smt

chemical emulsion dillute with 39 liter

go fIS concrentration total dillite

concentration will be 40 litre inclusive of

one litre chemical emulsion appication

at the rate of 7.5 Litre chemical / Sqm of

surface is recommended as per I.S

Providing erecting and fixing double

coated Syntex PVC.(ISI) water tank of

required capacity each with all necessary

fittings and connection etc. complete 3.91

Providing and fixing to wall, ceiling and

floor galvanised Mild steel tubes

(Medium grade) of the following

nominal bore, tube fitting and clamps

including making good the wall ceiling and

(A) 15mm (upto 10 ton)

(B) 20mm (upto 10 ton)

(C) 25mm (upto 10 ton)

(D) 32mm (upto 10 ton)

(E) 40mm (upto 10 ton)

(F) 50mm (upto 10 ton)

Providing and laying in trenches

galvanised mild steel tubes (Midium

grade) of the following nominal bore,

and tube fitting (Earth work in

trenches to be measured and paid for

(A) 15mm (upto 10 ton)

(B) 20mm (upto 10 ton)

(C) 25mm (upto 10 ton)

(D) 40mm (upto 10 ton)

(E) 65mm (upto 10 ton)

(H) 80mm (upto 10 ton)

Making connection of galvanised Mild

steel distribution branch with galvanised

mild steel main 50 mm to 80 mm

nominal bore by providing and fixing 600.08

tee including cutting and threading the

pipes complete.

Providing and fixing to wall ceiling and floor

6.0 Kg.F/Cm2 working pressure

poluthene pipes of the following out

142 side Dia. Low densidy, complete

with special falnge compression type

fittings,wall clips etc.including making

good the wall ceiling and floor.

Providing and fixing to wall ceiling and

floor 10.0Kg.F/Cm2 working pressure

polythene pipes of the following out

143 side Dia. Low densidy, complete

with special falnge compression type

fittings, wall clips etc. including making

good the wall ceiling and floor.

1.00 (C) 32mm Rmt

Providing and fixing cast iron (Spun)

Nahni trap of the following nominal

diameter of self cleaning design with C.I.

144 10.00 screaed down or higned grating Each

including cost of cutting and making good 600.08

the walls and floor 100 mm inlet and 50 mm

outlet.(C)100mm dia.

Providing and fixing water closet

squatting Pan (Indian type

W.C.Pan) size 580 mm (Earth work,

145 10.00 bed concrete, foot rest and trap to be Each

measured and paid for separately) (A)

Vitreous China. (I)Long pattern = White

Provdg. & fixing wall mounted White

/ Color Vitreous China European

water closet with integral P trap

146 5.00 of "Cera" - Clair Series or equivalent No.

incl. seat cover , Chair Bracket etc.

complete as per direction of engg. In

Providing and fixing wsh down water

closet (Europe an type, W.C.Pan) with

integral P or S trap including jointing the

trap with soil pipe in Cement

Mortar1:1 (1- Cement:1-fine sand) 1,290.80

(Seal and cover to be measured and paid

forseparately) (A) vitreous China

Pattern :(i) in white colour

Providing and fixing Urinal of approved

including connection with trap and with

148 10.00 integral No.

longitudinal flush pipe.(A) Squating plate

white earthenware 550mm x 300mm.

Providing & Fixing Angle cock of " Ess

Ess" - Trend series or equivalent

149 5.00 standard make as approved by engg. No.

in charge all complete. (N.S.)

Providing & Fixing pillar cock of " Ess

Ess" - Trend series or equivalent

149 A 5.00 standard make as approved by engg. No.

in charge all complete. (N.S.)

Providing and fixing 100 mm size P or

S trap for water closet squatting pan

including jointing the trap with the pan

and soil pipe in cement Mortar1:1 (1- 311.85

Cement : 1-Fine sand)(A) Vitreous

China.Pattern in white colour

Providing and fixing washbasin with single

pillar tap with C.I. or M.S. brackets painted

including sutting holes and making good the

151 5.00 same Each

but excluding fittings.(A) Vitreous China:(ii)

Back washbasin 550 mm x v 400mm size.

Providing and fixing Kitchen sink with C.I.

or M.S. brackets, painted white including

cutting holes in walls and making good

the same but excluding fittings. © 2,257.69

Vitreous China Sink. (i) 600 mm x 450 mmx

Providing and fixing 600 mm x 450 mm

bevelled edge mirrror of superior

glass mounted on 6 mm thick A.C. sheet

or ply wood sheet and fixing to wooden 825.48

pluge with C.P. brass screws and washers.

Providing and fixing chromium plated brass

halftrun flush cock of approved quality

fixing in pipe line etc. complete.(ii) 25mm

Provdg. & fixing White / Color

Vitreous china Counter wash basin with

signle hole for pillar tap of "Cera " -

Concord series of 550 x425 mm size to

be fiited in stone counter with necessary

brackets painted white incl. cutting

155 1.00 holes and making good the same .Cost No.

Includes P/F C.P. brass waste

coupline, 32 mm dia fisher union ,15 mm

dia. Pillar cock & Angle cock of " Ess

Ess"- Trend series ,32 mm dia. Waste

pipe etc. complete as per dir. of engg.

Finishing wall with water proofing cement

on wall surfaces (Two coats) to give an

brand and manufacture and of required

156 100.00 shape Smt

even shade after thoroughly brushing the

remove all dirt and remains of loose

Extra over Item 156 for every subsequent

156 a 5.00 water proofing cement paint of approved Smt

and manufacture.

Providing & Fixing S.S.304 Grade Sink

of Nirali / Krishna or Equivalent

157 2.00 Make for Kitchen Platform of size : No.

24":x18" as per Direction of engg. In

Providing and fixing Kitchen sink with C.I. or

brackets, painted white including cutting

157A 2.00 walls and making good the same but Each

fittings. (C) Vitreous China Sink.(i) 600mm x

Providing and fixing C.P. brass towel

rail comlete with C.P.brass brackets

158 5.00 fixed to wooden plugs with C.P. brass Each

scews.(B) 600mm x 20mm size.

Providing and fixing 600 mmx120 mm

glass shelf with C.P. brass bracket and

159 5.00 guard rail complete mixed to wooden Each

plug with C.P.brass screws.

Providing and fixing toilet paper holder.

(A) C.P.Brass 414.53

Providing and fixingof S.S. Railing pipe

161 5.00 mm x 16 G ASIS 304 Grade as per Rmt

instruction of engineer in charge.

Providing and fixing screw down bib taps

162 of following size. (B) Brass chromium plated

screws down Bib Tap.

Providing and fixing screw down bib taps

163 of following size. © Gun metal screw

Providing and fixing pillar tap, capstan

164 head, screw down high pressure with

screws, shanks and back nuts.

Providing and fixing Gun metal check

165 or non-return fullway wheel valve.

(III) 25 MM DIA

Providing and fixing brass screw down stop

165 A 1.00 Each

tap.(A) 15 mm dia 203.79

Providing and fixing chromium plated

brass half trun flush cock of approved

quality including fixing in pipe line etc.

(iii) 32mm dia.

Providing and fixing Urinal or

approved quality including

conecting the Urinal with waste pipe

tap etc.complete. (A) White earthen ware 1,026.01

flat back or corner type size 430mm x

Providing and fixing Urinal of

approved quality including

connection with trap and with integral

longitudinal flush pipe. (A) Squating 1,535.63

plate pattern white earthen ware

Providing and fixing chromium plated,

169 1.00 bottle trap with necessary couplings of Each

approved quality for wash basin.

Providing and fixing ball cock

170 1.00 ofapproved quality as directed. (A) Each

Copper Metal (i) 25mm dia.

Providing and fixing ball cock

171 1.00 ofapproved quality as directed. (A) Each

Copper Metal (i) 50 mm dia.

Filling with good Quality thor as and

where directed by the Architect /

Engineer-in-charge, in sunk in layers of

cm. thickness, including watering, 3,850.00

ramming well etc. complete, as directed

by the Architect / Engineer-in-charge .

Providing laying and jointing in true line and

level 15 mm dia. U.P.V.C. Pipe (SCH-40)

for cold water including fittings make

PRINCE/ SUPREME/ ASTRAL/ FINOLEX

or equivalent as approved by

Engineer In Charge. Pipe shall be fixed on

the wall with the help of clamp at every 71.93

two metre C/C or shall be concelled

as directed including necessary fittings

etc. including testing of pipe and joints and

fixing the same with solvent, including

cost of all materials.adhesive

Providing laying and jointing in true line and

level 25 mm dia. U.P.V.C. Pipe (SCH-40)

for cold water including fittings make

PRINCE/ SUPREME/ ASTRAL/ FINOLEX

orequivalent as approved by

Engineer In Charge. Pipe shall be fixed on

the wall with the help of clamp at every 90.93

two metre C/C or shall be concelled

as directed including necessary fittings

etc. including testing of pipe and joints and

fixing the same with adhesive solvent,

including cost of all materials.

Providing laying and jointing in true line and

level 32 mm dia. U.P.V.C. Pipe (SCH-40)

for cold water including fittings make

PRINCE/ SUPREME/ ASTRAL/ FINOLEX

or equivalent as approved by

Engineer In Charge. Pipe shall be fixed on

the wall with the help of clamp at every 117.97

two metre C/C or shall be concelled

as directed including necessary fittings

etc. including testing of pipe and joints and

fixing the same with adhesive solvent,

including cost of all materials.

Providing laying and jointing in true line and

level 40 mm dia. U.P.V.C. Pipe (SCH-40)

for cold water including fittings make

PRINCE/ SUPREME/ ASTRAL/ FINOLEX

or equivalent as approved by

Engineer In Charge. Pipe shall be fixed on

the wall with the help of clamp at every 146.65

two metre C/C or shall be concelled

as directed including necessary fittings

etc. including testing of pipe and joints and

fixing the same with adhesive solvent,

including cost of all materials.

Providing laying and jointing in true line and

level 50 mm dia. U.P.V.C. Pipe (SCH-40)

for cold water including fittings make

PRINCE/ SUPREME/ ASTRAL/ FINOLEX

or equivalent as approved by

Engineer In Charge. Pipe shall be fixed on

the wall with the help of clamp at every 193.73

two metre C/C or shall be concelled

as directed including necessary fittings

etc. including testing of pipe and joints and

fixing the same with adhesive solvent,

including cost of all materials.

Providing and fixing premoulded

compressible filler board in black colour

confirming to MoRT&H Specifications

(Clause 1015), having minimum density

95kg/cum. non-staining with less than 1%

water absorption & compression recovery 788.78

of 93% minimum as per specification for

mm wide expansion joint including cutting

to required size and shape at all levels

etc.complete as directed.

Fixing sun film for protection sunlight in

178 1.00 black or any colour as as directd by Smt

engineer In Charge.(Market rate)

Providing & Fixing 3 mm thick

F.R.P.sheet of Approved Quality & Color /

Pattern as per Consultant's design also

includes required fabrication structure in

the grid of 2'-0x2'-0 size using hollow

pipe of16 gauge & size 2"x1" & 1"x1"

179 1.00 ,G.I. & Bitumen Washers, Silicon paste SqM

application for fixing the sheet . Rate

also includesnecessary bending, cutting,

labor charges , Zinc Primer coat & Two

coats of oil painting of color as approved

by consultants & making good the wall.

Providing 2 mm thick F.R.P. Gutter with

180 1.00 necessary M.S. Supporting Brackets. Rmt

Hiring charges for J.C.B.machine

inclduing cost of fuel, operator, dirver

etc.. ( 12 hours sift day/night) 600.00

To provide tractor with hydraulic trolley,

driver, 4 Nos. of Labor with all tools like

bucket drum, showels, trikam,

pavadas, etc,, to carryout different

works during monsoon for 12 Hrs. Shift. 3,000.00

Work shall be carried out as per the

instrucitons of Engineer In-Charge.No extra

charged shall be paid for night shift.

Roller Blind Providing and fixing Roller

Blind curtain fixed on window level

on wooden batten and curtain lift with

cotton thin rope, make of aerolax

183 1.00 or equivalent design and colour as per Smt

instruction by engineer – in – Charge

with necessary hardware fitting, material

and labour etc complete.

Providing & Fixing Door closer - complete of

184 2.00 Approved make to wooden / Aluminium No.

Doors as per direction of engg. In charge.

Providing and fixiing M.S. Fan clamps type

1 of 16 mm dia M.S. bar bent to shape with

hooked ends of R.C.C. slabs during laying

incl. painting the exposed protion of loops, 124.74

all as per standard design complete.

Providing cement vata (10cm. x 10 cm.

size) quarter round in cement mortar 1:1

186 1.00 including neat cement finishing, watering Rmt

Making Water connection from exi.Muni.

Water line (N.S.) 250.00

Applying and providing Expansion joint

System on 100 mm vide joint including

exansion joint by mechanical means

adhesive and flexible membrane with

bond length as per menufracturer 4,724.75

specification and

4mm thick alluminium strip covering with

sloted and bolted with suitable system,

all manpower, machinery and material as

specification and as directed.

Providing and Fixing 1 H.P. Electrical

monoblock or submarcible water pumps

189 1.00 withmotor and required cable and switch Set

board of approved brand and make

etc.comp.as directed.

.Providing TMT Bar FE 415 reinforcement

for R.C.C. work including bending, binding

190 a 150.00 and placing in position complete up to floor Kg.

two level (up to 10 ton)

ProvidingTMTBarFE500/500Dreinforcement

for R.C.C.workincluding bending,binding

and placing in position complete upto floor

b 150.00 two level placing in position complete upto Kg.

floor two level placing in position complete 75.46

upto floor two level(upto 10 ton)

Providing and fixing 30mm thick solid both

side prelam PVC door shutter (sintex door-

191 10.00 equivalent) with necessary alluminium Smt

fitting with EL-7 section frame

Providing & Fixing in position Alluminium

window sliding / fix type with frame using

approved anodised extruded alluminium

section as approved by Engg. In

charge.(Jindal alluminium) units equivalent

(a) Frame sections 65 x 25 mm ( at

kg/mt) (b)Sliding Frame bottom section of

Shutter top & bottom section 40 x18 mm (

wt. 0.41 Kg/Rmt ) (d) Shutter interlock

vertical section 10 x 18 mm.( 0.41 Kg/ Rmt)

(e) Shutter vertical of 40 x 18 mm. (0.41

Kg/Rmt) including P/F installing 5 mm thick

approved color Acrylic sheet of standard

quality etc.comp.

Providing and laying polished granite stone

slab 18 mm thick in risers of steps, dedo

and pllars laid on 10 mm thick cement

mortar 1:3 (1 cement:3 coarse sand) and 2,690.00

jointed with gray cement slurry including

rubbing & polishing etc.complete.

Wall panelling with 12 mm MDF fixed to

existing alluminium framing and making

194 1.00 grove as per design and finished with Smt

royal plastic paint as per instruction of

engineer incharge. (N.S.)

Providing and laying 15mm

bamboza wooden flooring as per

architect's drawing with all

necessary details as directed by the

project consultants. Use underlay for 2,690.00

better result as per Detail specifications

and directed by the project consultants.

(N.S.) (Approved Rate )

Providing 20 mm thick double coat mala

cement plaster on interior brick / concrete

work for plastering comprising of base coat

of 12 mm thick cement plaster in cement

196 1.00 mortar (1 Cement : 4 coarse sand) in rough Sq.M.

finishing and 8 mm thick top coat of cement

mortar 1:2 (1 Cement : 2 Coarse sand)

finished with trovel including scaffolding

curing etc. complete.

Finishing wall with weather proof exterior

emulsion paint on wall surface (two coats)

197 1.00 give an required shape evenshade after Sq.M.

thoroughly brushing the surface to remove 113.40

all dirt, and remains of loose powdered

materials.etc complete

High Back Chairs for vip Lounge

:Supplying and installation of

“Revolving High Back” chairs. The chairs

must be robust, ergonomically

designed and comfortable. Seat

& Back Assembly -1.2 cm thick

hot pressed plywood and upholstered with

Fabric and Molded Polyurethane

Foam with PVC lining all around.

Back foam is designed with contoured

lumber support for extra comfort. Chairs

Dimension - Width 55 cm, Depth 60 cm

Height 103 – 115.5 cm, Seat Height(SH)

44 – 56.5 cm. The Polyurethane foam

should be molded with density 45+/-2

kg/m3 & Hardness = 16+/-2

kg/m3onHampden machine at 25%

compression. Arm Rest - One-piece

Black integral skin polyurethane with

50-70 shore. `D’ Type Handle and

reinforced with MS insert. Centre

Pivot Mechanism - 360o revolving type

17o maximum tilt on pivot at centre Tilt

tension adjustment. Upright locking.

Telescopic Bellow Assembly - The

bellow should be 3 piece telescopic type

and injection molded in black

Polypropylene. Hydraulic Height

Adjustment - The Hydraulic height

adjustment should be provided with

adjustment stroke of at least 10cms.

Pedestal Assembly - The pedestal

should be injection molded in Black

powder coated MS on and fitted with

nos. twin wheel castors. Twin wheel

castors - The twin wheel castors

should be injection molded in Black

Nylon The complete item as per

architect /engineer in charge

Providing and supplying Medium Back

Chair for Control room MODEL

LIKE HOF OCT 172 Revolving

synchro tilting mechanism based

chair with gas lift for adjustable

height and medium curved back with seat

and back PU molded cushion with MS

pipe frame structure and white foam

layer for seat and molded PU foam. White

foam layer for back covered with thick

199 1.00 cloth and draped with cloth of Each

approved shade. (min. of Rs.150/meter).

5 legged revolving molded nylon chair

base with good quality of PU castors with

2 years replacement guarantee. The chair

to have wide polyurethane arm rest of

approved shape. Complete chair should

be in suitable shape. Rates to be

inclusive of all taxes and free delivery

at site. The complete item as per

architect /engineer in charge

Providing and fixing storage, entire unit to

be made from 19 mm th. and 12mm Ply

with 1.0mm &. 8 mm th. Laminate.

Shelves to be made from 19mm Ply

with both side laminate. Rate shall

include necessary approved mortise

locking systems, S S Handle pair 2" to 12,500.00

4" height and necessary hardware.

Over all storage to be completed with

necessary hard ware and accessories

completed as per drawing and design

as given by Architect.

Existing storage repairing and veneer

on top Providing and fixing of Louvers On

Existing d.c panel Providing and fixing

35mmthk. Louvers shutter made up

from Ghanateak frame with 135x75mm

and shutter frame as per detail and fixing

aluminum louvers which is

201 1.00 specified readymade powder Smt

coated aluminum grill panel louvers .and

applying melamine spray polish all exposed

wood work. Overall door to be

completed with necessary hardware

and accessories completed as per

drawing and design as given by

Engineer In charge/Architect.

Providing and fixing flush door

shutters, solid core construction with

frame of first class hardwood with cross

board and face veneer or plywood face

panels, with both side 1 mm

laminate finishing including anodized

aluminum butt hinges with necessary

screws. Decorative type and pine

wood core anodized minimum 3 no

mm long aluminum butt hinges in flush

202A 1.00 door shutters with 2 no of brass holdfast Smt

325 mm long 1 no brass tower bolt

mm long and two no of 150 mm long brass

door handle . Decorative both side

laminated Flush door 35 mm thick. with

frame of 10 cm x 7 cmt Indian teak

wood frame including all necessary

fitting fixtures hardware screw and

adhesive etc fixing up to all lead and lift

height up to 45 mtr from GL etc complete

as per direction of engineer in charge

Providing and fixing 35mm thick factory

made moulded door shuter consisting of

solid core single leaf flush door of 30mm

thickness, lipped with 15mm (5mm x 3)

thick x 30mm width on one stiles and top

rail and 10mm (5mm x 2) thick x 30mm

width on the other stilesand bottom rails.

The inner panel laminated with 2mm thick

termite proof, water proof and fire resistant

B 2.00 moulded PVC Smt

sheet with 2,4,6 raised panel design in

different plain and /or prelim colours on one

side after routing the moulded design on

flush door and 2mm plain and/or prelim

PVC sheet on other side using rubber

adhesive on flush door and solvent cement

adhesive on the PVC liping etc. complete

as per direction of Engineer in charge,

manufacture’s specification and drawing.

P/M/F chainlink jali 8'x4' size as per details

sketch & instructionof engineer in charge

same as lal darwaja garden pattern

consisting of 3'dia. M.S black pipe 'A' class

5'4" ht. fixed at 8'9" c/c in C.C 1:2:4 block of

9"x9"x9" size chain link jali of size 2"x2"x10

gauge fixed in 35x35x5 mm MS angle

frame 8'x4' size with MS flat of size 25x3 1,230.00

mm welded jali etc.comp.The jali is to be

welded to MS pipe with MS flat as

instruction given.The M.S pipe and the M.S

angle frame are to be painted one coat of

primer and two coats of paint as directed in

line and level. (N.S)

Providing & Fixing masonary wall with

porbandar lachiya stone with well dressed

grooveas per directed by engg.in charge for

foundation, plinth or super structure level

(above plinth level upto floor two level) in

204 cement mortar 1:5 (1-cement : 5-fine sand)

incl.pointing the joint with white cement and

yellow oxide powder in proportion to match

stone colour the joints should be thread

grooved as per exi. lake stone pitching

(A) stone masonary wall/stone dressed

0.00 single faced (size 15"x8"x9") Cmt

(B) stone coping (size 15"x8"x4")

(C) stone coping (size 15"x8"x9")

(D) stone column (size 15"x15")

(E) stone column top (size 20"x20"x9")

Supplying and fixing of 300 mm-L x

mm-B x 380 mm-H Kerb block for

Footpath in M-20 grade using 20 mm

nominal size black trap aggregate of

Sevaliya/Timbaor equivalent quality

for pre-cast blocks,

reasonablyexposed finish/

formwork , mould with well

equippedwith vibratory system for kerb

stones of approved design including

curing, etc. complete, including thecost

of formwork etc. complete. The rate

shall also include necessary cutting

of asphalt, fixing the Kerbstones in line 350.89

and level on 5 cm thick sand bedding

withnecessary equipments and materials.

The rate shall also include the flush

pointing in CM (1:3) for all joints of

thekerbstones. Filling of zari alone the

sides of the kerbstone fixed with

Bituminous concrete

Bituminousconcrete / C.C. mixed in

proper position to flush withthe road

surface as directed by Engineer in

change to form a portable mixture.a)

Laying on 5 cm thick Sand Bedding

Providing and fixing pre-cast concrete kerb

stone of gray cement based concrete block

30cm length,30cm height and 15cm thick of

b 1.00 M200 grade concret as per approved Rmt

design and including excavation for fixing in 376.43

proper line and level,filling the joint with

C:M 1:3 (1cement:3fine sand) etc complete.

Providing and Laying of Rubber Moulded

Paver Block Grey/Coloured 60 mm thick, M-

35 Grade of any size shape (Usually Uni-

Paver Blocks) using black trap good quality

aggragate of 20 mm nominal size for

footpath,parking areas, service lanes and

other areas as mentioned in the drawing /

instruction of engineer in charge. Cost

includes formworks using rubber mould,

Rate providing and laying paver blocks as

per required grading and specification. The

paver block shall be mechanically

206 10.00 compacted. The work of paving blocks shall Smt

be executed in line and level by skill mason

of flooring work only. It should be laid in

such a way that the no cutting of the paver

block to be necessary. if cutting of paver

block necessary then it should be cut by

machine only and carting. The finished

surface of the paver block shall have

resonably good, plain finished. Paver

blocks shall be compacted and shall be

relaid if necessary. Gravel or such type of

materials shall not be allowed for

production. Laying on 5 cms thick sand

Provoding and fixing flush door shutters,

solid core construction with frame of first

class hard wood with cross board and face

veneer or ply wood face panels, including

anodised alluminium butt hinges with

necessary screws. (B) Non- decorative type

and block board core anodised alluminium 1,779.97

butt hinges in flush door shutters (2) 35 mm

thick. Labour work for fixing any kind of

paving with cement pointing in CM 1:2,

including watering, ramming etc comp. as

dir.For pavement

I) Laying on Sand bedding as per

208 5.00 requirement to fix the C.C.Block / Nibhada Smt

Stone in Line & Level

Box type metal letters forming composite

box made from 1mm thick stainless steel

plate of grade 304 having brush finish of

209 following font size to be fixed at Main Gate

in english and or Gujrati and including fixing

charges approved before fixing by clent /

Providing and fixing false ceiling at all

height including providing and fixing of

frame work made of special sections, power

pressed from M.S. sheets and galvanized

with zinc coating of 120 gms/sqm (both side

inclusive) as per IS : 277 and consisting of

angle cleats of size 25 mm wide x 1.6 mm

thick with flanges of 27 mm and 37mm, at

1200 mm centre to centre, one flange fixed

to the ceiling with dash fastener 12.5 mm

dia x 50mm long with 6mm dia bolts, other

flange of cleat fixed to the angle hangers of

25x10x0.50 mm of required length with nuts

& bolts of required size and other end of

angle hanger fixed with intermediate G.I.

channels 45x15x0.9 mm running at the

spacing of 1200 mm centre to centre, to

which the ceiling section 0.5 mm thick

bottom wedge of 80 mm with tapered

flanges of 26 mm each having lips of

mm, at 450 mm centre to centre, shall be

fixed in a direction perpendicular to G.I. 850.00

intermediate channel with connecting clips

made out of 2.64 mm dia x 230 mm long

G.I. wire at every junction, including fixing

perimeter channels 0.5 mm thick 27 mm

high having flanges of 20 mm and 30 mm

long, the perimeter of ceiling fixed to

wall/partition with the help of rawl plugs at

450 mm centre, with 25mm long dry wall

screws @ 230 mm interval, including fixing

of gypsum board to ceiling section and

perimeter channel with the help of dry wall

screws of size 3.5 x 25 mm at 230 mm c/c,

including jointing and finishing to a flush

finish of tapered and square edges of the

board with recomme-nded jointing

compound , jointing tapes , finishing with

jointing compound in 3 layers covering upto

150 mm on both sides of joint and two

coats of primer suitable for board, all as per

manufacturer’s specification and also

including the cost of making openings for

light fittings, grills, diffusers, cutouts made

with frame of perimeter channels suitably

fixed, all complete as per drawings,

specification and direction of the Engineer

in Charge but excluding the cost of painting.

Providing and fixing wall acoustical

paneling using ecotone Slato/ Anutone

slato or equivalent Acoustic Panel make

Slats L-16 of size 128mmx2430mmx16mm

thick up to 2400mm high as per the

following specification :-Slats L-16- 2mm

@16mm, 32 x 128 x 2430 mm high grade

Pine wood base Medium Density Fiber

acoustic boards with Tongue & Groove

Edge,2mm slot perforation @ 16mm centre,

slates perforations, The acoustic should be

furnished with a Black absorbent felt

backing with an airflow resistance of 330-

211 1.00 460 Ns/m³ (DIN 53887),wood practical Sq.mt.

core,NRC : should be Up to 0.75,should

meet the safety requirements of EN

Fixing :- Sound Strut CC18 screw fixed

horizontal/vertical to wall at every 600mm

c/c. Metal cleat can be fixed on top edges

of Sound Strut CS55 fixed directly by

stamping to the CS55 and IC91 which is

screw fixed directly to the wall where ever

required with a backing black color fabric as

approved by Architect and as specified

including all accessories, material & labor

complete as directed by Architect /

Providing & Fixing SPEED BUMP - #2 No

(1 black, 1 yellow) 350 x 500 x 50 mm, Size

per color End Cape 350 MM x 175 MM x

MM TOP DESIGN - Lining Top flat ANTI

SKID PATTERN FOR GRIP COLOUR :-

YELLOW & BLACK BODY MATERIAL :-

MODIFIED THERMOPLASTICS (Polymer

Rubberized ) • ECO FRIENDLY 2,185.00

RECYCLE RUBBER Packing :- 4 pcs/

woven Bag Load Capacity :- 20 MT Fitting (

Fixing on TRAKE) :-4 holes & END CAPE :-

2 HOLE HEX Bolts with Washer Epoxy for

Bolt Fitting etc. complete as directed by EIC

Providing & Fixing in position 24 MM

exposed grid suspension system with “P “

Grid profile false ceiling system using

MM X 600 MM ecotone/anutone or

equivalent make Glass Fiber Ceiling Tiles

having tegular edges & 0.90 NRC value

and approved surface design (with NRC of

0.90) and edge profile Tegular placed in a

suspended grid of size 600 MM X 600 MM

made from hot dipped GI Steel sections,

rotary stitched, main tee of size 24 X 42 X

3000 MM X 0.40 MM thickness suspended

213 1.00 at every 600 MM c/c along length of ceiling Sq.mt.

with 4 MM dia, Pre-straightened G.I.Wire

with necessary level adjusters &

intermediate cross tees of size 24 X 38 X

600 MM X 0.40 MM thickness shall be

inserted in to slots between the main tees

at 600 MM centers in direction vertical to

the main tees, where in the main tees are

resting on the periphery on wall angles of

size 24 MM X 24 MM X 3000 MM X

MM thickness including providing

necessary openings for light fixtures,

Providing and fixing of Roller blind

curtain/blackout. The fabric shall be woven

from formulated platisol extruded over a

polyaster yarn.The fabric shouldl be

214 1.00 weaved to provide subtle view of the side of Smt

the blind and should offer elimination of

glare and sunlight radiance upto a minimum

of 80%.The fabric shall be flame retardant.

Providing and applying Texture Paint

(Rustic Finish) on external plastered

surfaces, pattern as per sample approved

by the Architect. including preparing

surface, using roller to get approved

texturised surface. Job to include making

215 1.00 required surface preparation, to receive Sq.m

Texture paint finish etc. All complete as per

detail drawing, as specified and as directed

by Architect / Consultant / Project - In -

Charge. The rates shall be inclusive of

Scaffolding, all material, labour etc.

complete. as directed by EIC.

Providing and fixing PVC/Gpsysum plain

colour false ceiling with grid type with

aluminium frame from gypsteel, fastners

,props, Finishing as per architectural

drawing allowing openings for

A.C. Diffusers, Light/Electrical Points 766.00

etc –complete, Prior to fixing on

frame.(Brand : Anutone or

equivalent ) (N.S.) or as directd by engineer

Provdg. & laying S.W. Gully trap with brick

masonry chamber & water tight G.T.Stone

217 10.00 including fixing of covervSquare mouth trap No.

100 mm x100 mm size P-Trap

Providing cement vata (10cmx10cmsize)

quarter roundin cement mortar 1:1 including

neat cement finishing, waterin getc. 23.45

Providing and laying (to level or slopes) and

jointing with stiff mixture of Cement Mortar

219 5.00 in proportion 1:1 Salt glazed stoneware Rmt.

pipes including testing of pipes and joints

complete.(A) 100mm dia.

Providing and laying (to level or slopes) and

jointing with stiff mixture of Cement Mortar

in proportion 1:1 Salt glazed stoneware

pipes including testing of pipes and joints 288.23

complete.(B) 150mm dia.

Constructing brick masonry chamber for

underground C.I. Inspection chamber and

bends with bricks having crushing strength

not less than 35Kg/Cm2 in C.M. 1:5 C.I.

cover with frame (Light duty) 455mm x

610mm intenal dimensions total weight of

cover with frame to be not less than 38Kg.

(Wt. of cover 23 Kg.) and Wt. of frame

221 1.00 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1- Each

cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete

1:5:10 inside plaster 15mm thick with

cement mortar 1:3 finished smooth with a

floating coat of neat cement on walls and

bed concrete etc. complete.(i) Inside

dimensions 455mmx 610mm and 450mm

deep for single pipe line.

Constructing brick masonry chamber for

underground C.I. Inspection chamber and

bends with bricks having crushing strength

not less than 35Kg/Cm2 in C.M. 1:5 C.I.

cover with frame (Light duty) 455mm x

610mm intenal dimensions total weight of

cover with frame to be not less than 38Kg.

(Wt. of cover 23 Kg.) and Wt. of frame

15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-

cement :2- coarse sand :4-graded stone 3,624.51

aggregate 20mm size) foundation concrete

1:5:10 inside plaster 15mm thick with

cement mortar 1:3 finished smooth with a

floating coat of neat cement on walls and

bed concrete etc. complete.(i)Inside

dimensions 500mm x 700 mm and 450mm

deep for pipe line

with one or two inlets.

Constructing brick masonry chamber for

underground C.I. Inspection chamber and

bends with bricks having crushing strength

35Kg/ Cm2 in C.M. 1:5 C.I. cover with

frame (Light duty) 455mm x 610mm intenal

dimensions total weight of cover with frame

to be not less than

38Kg. (Wt. of cover 23 Kg.) and Wt. of

frame 15Kg. ) (R.C.C. top slabe with 1:2:4

222A 1.00 mix (1-cement :2- coarse sand :4-graded Each

stone aggregate 20mm size)

foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement

on walls and bed

concrete etc. complete.(iii) Inside

dimensions 600mm x 850 mm and 450mm

deep for pipe lines with three or more inlets.

Providing, supplying and fixing precast C.C.

blocks (M-20) edge kerb having size of

x 300 x 300 mm depth and as per design

conveying it to the site, jointing into C:M 1:3 219.00

and racking out the joints incl. necessary

excavation of asphalt, soil etc..completed.

Constructing a cooking Sandwich platform

60 cm. width and 70 cm high resting on

B.B.Masonry walls

23 cm.thick in C.M.(1:6) with (ii) Fixing

black Granitee 30mm thick laid on precast 933.98

R.C.C. (1:2:4) slab with plastering on

exposed faces of wall in C.M. (1:4) etc

Constructing a cooking platform 60 cm.

width and 70 cm high resting on

B.B.Masonry walls 23 cm.thick in C.M.(1:6)

224b 1.00 with (ii) Fixing black kadappa stone 30mm Rmt

thick laid on precast R.C.C. (1:2:4)slab with 1,132.43

plastering on exposed faces of wall in C.M.

(1:4) etc complete.

Providing and fixing hard drawn steel wire

fabric 75mm x 25mm mesh or weight not

225 1.00 less than 7.75 kg. per Sq.M. to window Smt

frames etc. including60 x 20mm beading of

Providing & fixing 15 cm wide chicken mesh

jali with nails & then application of 15 mm

226 1.00 plaster on R.C.C.& masonary joints as per Rmt.

dir.of engg.in charge

Providing and laying cement concrete

flooring 1:2:4 (1-cement : 2-coarse sand : 4-

graded stone aggregate 20mm nominal

size) laid in one layer and finished with a 348.08

floating coat of neat cement. (A) 50mm

Providing and constructing, Underground

(U/G) water tank of specified capacity, on

specified location, for all depths, in

controlled CC of M-200 grade with bottom

slab, top slab and RCC walls, including cost

of form work and reinforcement,with inside

and outside plaster in CM 1 :3 and water

228 10.00 Litre

proofing treatment as per IWP 6.50

specification,including injection, grouting,

etc. complete. The rate includes for

providing and fixing two nos. 0.6m. x 0.6 m.

size medium duty CI manhole cover/s at

top, including wash out pipe line and inlet

and outlet connections etc. complete.

Providing & Fixing of Armstrong Mineral

Fibre Acoustical Suspended Ceiling System

with Dune (Bevelled Tegular) Edge Tiles

With Armstrong 15mm Exposed GRID. The

tiles should have Humidity Resistance (RH)

of 99%, NRC 0.5, Light Reflectance ≥85%,

Thermal Conductivity k = 0.052 - 0.057 w/m

K, Colour White, Fire Performance UK

Class 0 / Class 1 (BS 476 pt - 6 &7) in

module size of 600 x 600 x 15mm , suitable

for Green Building application, with

Recycled content of 32%. The tile shall be

laid on Armstrong Silhouette profile grid

229 1.00 system with 15mm white flanges Smt

incorporating a 6mm central reveal in

white/black colour and with a web height of

45mm and a load carrying capacity of

minimum 15.68 Kgs/M2 & minimum pull out

strength of 100 Kgs.. Silhouette, Main

Runners & Cross Tees to have mitred ends

& “birdsmouth” notches to provide mitred

cruciform junctions. The T Sections have a

Galvanizing of 90 grams per M2 and need

to be installed with Suspension system of

Armstrong make. Warranty Certificate and

Test Reports for NRC, CAC and Fire rating

shall be provided by Vendor.

Mineral Fibre Acoustic Modular Ceiling Tile

should be GREENPRO certified and

qualifies as GREEN PRODUCT certified by

CII Green Products and Services

Council.INSTALLATION: To comprise main

runner spaced at 1200mm centres securely

fixed to the structural soffit using Armstrong

suspension system (specifications below) at

1200mm maximum centre. The First/Last

Armstrong suspension system at the end of

each main runner should not be greater

than 450mm from the adjacent wall. Flush

fitting 1200mm long cross tees to be

interlocked between main runners at

600mm centre to form 1200 x 600 mm

module. Cut cross tees longer than 600mm

require independent support. 600 x 600mm

module to be formed by fitting 600mm long

flush fitting cross tees centrally between the

1200 mm cross tees.Perimeter trim to be

Armstrong wall angles of size

3000x19x19mm, secured to walls at

mm maximum centres. Installation should

be carried out as per Armstrong

recommended procedure.ARMSTRONG

SUSPENSION SYSTEM accessories

manufactured and supplied by Armstrong

World Industries consisting of M6 Anchor

Fasteners with Vertical Hangers made of

Galvanised steel of size 26 x 26 x 25 x

1.2mm with a Galvanised Thickness of

80gsm, A pre Straightened Hanger wire of

dia – 2.5 mm of 1.8 m length., thickness of

80gsm and a tensile strength of 344-413

MPa, along with Adjustable hook clips of

0.8mm thick, galvanised spring steel for

2.68 mm with a minimum pull strength of

110 kg. The adjustable clip also consists of

a 3.5 mm aquiline wire to be used with the

Providing and fixing PVC Printed pain

colour false ceiling with grid type with

alluminium frame consisting of 600mm x

600mm 3mm thick plain PVC sheet used as

panel insert in a frame work made using

anodized alluminium T section of size 1 x

(235 x 25mm, 19 gauge or 1 mm thick) in

square pattern of grid sizes of 2 x 2 (600 x

600mm) The alluminium frame work is

supported from the cceiling with the help of 766.00

G.I. hook and G.I. wire/6mm M.S. rods of

required sizes to maintain proper level etc.

The aluminium frame work is supported on

side wall with the use of alluminium L

section of size 1 x1 (25 x 25mm) angles

etc. complete as per direction of Engineer

in charge. Manufactures specification and

Providing and supplying of labour for

necessary manual excavation, cleaning,

Shifting of Material Or any other, or for any

other work as directed by Engineer In 551.00

charge. The Rate includes Handcart with

Fitter/Plumber/Mason

WELDER/ Gas cutter at Day /night

Supplting of welding machine / gas cutter

including cost of welding rods/gas,

Transportation, including carting from site to 1,500.00

Mazdoor at Day Male/Female

Conveyance charges of (A) lime murrum

building rubbish earth manure or

sludge & execavated rock andrubbish

[Limemurrum building rubbish 326.73

Supplying electric breaker machine for RCC

slab or asphalt demolishing work on site by

using operator, fuel, power supply

etc.complete as directed. (no payment

233 3.00 should be allowed for non working condition Shift

of machinery and for pipe line excavation

and M.H. work. Allowed only for break

down work) (Based on Previously approved

rate by CE sir )

CatchPit Jali Fixing P/F FRC catch pit jali

with frame 600mm x 600mm clear opening

234 4.00 etc. comp. As directed by engineer in No.

charge. (Based on Central Store Rate)

Providing and fixing concealed center point

to wall ceiling & floor CPVC (SDR 13.5)

PIPE having National Sanitation Foundation

235 (NSF) seal for potable water of following

dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and

floor etc. complete.

Providing and fixing cast iron steps of size

500mm x 150mm x 22.5mm and painting

236 8.00 with two coats of Anti-corrosive paint etc. Each

Supplying and fixing C.I. cover 300mm x

300mm without frame for Gulley trap

237 10.00 (Standard pattern) te weight of cover to be Each

not less 4.53 Kg.)

Providing and fixing to wall ceiling and

floor 10.0Kg.F/Cm2 working pressure

polythene pipes of the following out

238 side Dia. Low densidy, complete

with special falnge compression type

fittings, wall clips etc. including making

good the wall ceiling and floor.

Providing and fixing sheet glass, selected

quality (Type-C) bedded in putty and fixed

239 1.00 wooden beading including the cost of Smt

wooden beadings of first class teakwood

and necessary cutting of glass. (2) 6 mm

Providing and fixing rough cast wired glass,

6mm thick bedded in putty and fixed with

wooden beading including the cost of

240 1.00 wooden beadings of Indian teak wood and Smt

necessary cutting of glass. (C) Wired - 559.26

Providing and fixing five courses water

profing treatment with bitumen felt

consisting of second and fourth course of

blown / bitumen or/ and residual bitumen

applied hot at 1.2 kg.per Sq.M.of area for

each course and first course with fibre base

bitunen saturated under lay type land third

with fibre base self finished felt type 2 grade 466.84

fifth and final course of stone grit 6mm and

size or pea sizes gravel spread at

Cu. Metre / Sq. metre

including preparation of surface excluding

grading complete.

Providing and fixing three courses water

profing treatment of Astral Make Company.

with an first layer of first course with fibre

base, Second Course of Water Proofing

chemical coat, and Third Coat of Fibre Coat

with fibre base self finished felt type 2 grade

1 and final course of Burshing with 753.20

chemical Treatment with a thickness of 1 to

2 mm thickness, including preparation of

surface , The Said work should be provided

for a perfomance bond of 5 Years for

warranty purpose.

Constructing Manhole with R.C.C. top slab

in 1:2:4 mix (1-cement :2-coarse sand : 4-

graded stone aggregate 20mm nominal

size) foundation concrete1:3:6 mix (1-

cement : 3- coarse sand :6-Brick bats 40 +

50mm size) inside plastering 15mm thick

with Cement Mortar 1:3 (1-Cement : 3-

coarse sand) finished with a floating coat of

neat cement and making channels in

cement concrete 1:2:4 mix (1- Cement :2-

Coarse sand :4-stone aggregate 20mm

nominal size) finished smooth complete

including curing and festing (i) Inside size 10,920.76

and 1.5M. deep including C.I. cover with

frame size 560mm diameter total weight of

cover and frame to be not less than

kgs. (Wt. of cover 64 Kg. and Wt. of frame

64 Kg.)(A) With 230mm thick walls of brick

msonry using brick having crushing

strength not less than 35Kg. / Sq.cm. in

Cement Mortar 1:5 (1- Cement: 5-Coarse

sand) (1) A type depth 0.90 Metre for

150mm diameter sewer.

Providing and fixing of wall paper at

Wall/Ceiling/ or at other places, as required.

( Basic Rate of Wall paper must be (100-

120) Rs. Per Sq.Ft. The Rate includes of 140.00

necessary material, with fixing and

transporation with necessary solution.

Providing and fixing of Shower of jaquar

245 1.00 make for Serial No. 0797N ALD ( High Flow No's

C/Body-Jaquar, Primary Batch )

Providing and fixing of Metro Pole of 40 mm

246 1.00 dia of Jaquar Make of series FLV-1093 N ( No's

Serial No. 10935 )

Providing and fixing of chair bracket for

247 1.00 Support of W.C. of Primary batch Series- No's

7324 of Jaquar make

Providing and fixing of upper part of W/C of

jaquar series of 8481 2,378.00

Providing and fixing of 2 in 1 Bib cock of

249 1.00 jaquar Series of KUP-35041 (8481) as per No's

Instructions of engineer in charge.

Providing and fixing of Pillar cock of jaquar

250 1.00 make series EXTND 190 MM as per No's

instructions of engineer in charge.

Providing and fixing of Angle cock of jaquar

251 1.00 make series of KUP-35053 PM No's

Providing and fixing of shower of size

8x8m including shower arm, flange, floor

252 1.00 trape, including all material with fixing as No's

per Instructions of engineer in charge.

Supplying and fixing of Roller blind curtain

In Patterned Fabric of Different Textures

corded in roller blinds with stiching fittings

and of stichles pattern. The Price Rate

Includes necessary Making with fixing of 6,670.00

roller blind with roller mechanism as

instruction and selection of design as per

engineer in charge.

Supplying and fixing of Sheer Curtains of

Different Size, In Patterned Fabric of White

Colour Textures stiching fittings and of

254 1.00 stichless pattern. The Price Rate Includes Smt

necessary Making with fixing of Sheer 1,955.00

Curtain with top channels of fixing as

instruction of engineer in charge.

Supplying and providing of Green Curtain

for prevention of Sunlight. The Price Rate

Includes blackout curtains with dense or

255 1.00 fabirc or foam interlining material. The Price Smt

Rate also Includes necessary fixing with 1,162.00

roller tie ropes at site at any height as per

instruction of engineer in charge.

Supply & fixing factory finished cold formed

Light guage steel frame sections confirming

to SP:6 (5) 1980 at site or work including

riveted, bolted or welded in builtup for all

257 0.00 type of sections ,in framed work, cutting, Kg.

hoisting, fixing in position and

applying primer coat of approved steel

primer etc. complete as per structural

designs & directions of Engineer-in-charge.

Providing valleys 900mm overall in plain

1.6mm thick G.I. sheet fixed with G.I. J or L

Hooks, Bolts and nuts glavanised iron J or

L Hooks Bolts and nuts 8mm dia G.I. 1,042.78

Limpet and bitumen washers complete.

Providing laying (to level or slopes) and

jointing reinforced concrete Light duty non-

pressure pipes I.S. class NP2 of the

following internal diameter with collars and 658.89

butt ends prepared for collar joints including

testing of joints complete.(D) 300mm

Constructing Manhole with R.C.C. top slab

in 1:2:4 mix (1-cement :2-coarse sand : 4-

graded stone aggregate 20mm nominal

size) foundation concrete 1:3:6 mix (1-

cement : 3- coarse sand :6-Brick bats 40 +