SPECIAL REPAIR TO BLDG NO EW 182 IN ASHIANA COMPLEX AT IMA DEHRADUN

Amount

M&L for Non skid ceramic coloured tiles 7 to 8mm thick (Square or rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, laid in floors etc, set and jointed in neat cement slurry and pointed in white or coloured tile grout to match the shade of tiles with and including laying of 15 mm thick screed bed or bedding layer in cement mortar 1:6 complete including dismantling of existing floor tiling including cement mortar bedding and removing out side IMA premises complete all as directed. Note :- Colour as approved by GE.

M&L for Vitrified ceramic coloured tiles 7 to 8mm thick (Square or rectangular) polished, area of each tile n exceeding 0.36 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in tile grout to match the shade of tiles laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 including dismantling floor hearth or wall tiling including cement mortar bedding and removing out side IMA premises complete all as specified and directed. Note :- Colour as approved by GE.

M&L for Glazed ceramic coloured tiles of size 450x300x7mm thick, as in vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in same colour tile grout to match including rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 for receiving wall tiles and dismantling of existing tile and removing out side IMA premises complete all as directed. Note :- Colour as approved by GE.

S&F in repair single piece Vitreous china any shade cascade floor mounted single piece water closet P/S trap with dual flush and UF soft close slim seat cover, hinges fittings, conversion bend, fixing accesories complete all as specified and directed. Make : Jaquar Cat part No OPS-WHT15753NS250UFSMZ/ Cera cat part No S1013105/Kajaria cat part No KB-3007

S&F in repairs Vitreous china full set pedestal type wash basin, white, flat back, size 585x450x220mm including bracket, CP brass 32m dia coupling, waste pipe complete all as directed. Make : Jaquar Cat part No FLS-WHT-5801 & 5301/Cera cat part No S2040112 & S2090107 or equivalent Make :- Kohler

S&F in repair PVC connection 450mm long 15mm in size with brass or PTMT check nut and PVC washers at both ends complete

S&F in repairs sheet glass shelf assembly consisting of 5.0 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long.

S&F in repair Corner glass shelf assembly with bracket complete all as specified and as directed.

S&F in repair toilet paper holder with flap guard fixed to walls with chromium plated brass screws. Make : Cera cat part No F5013110CH or equivalent in Jaquar/Kohler.

S&F in repair soap dish holder fixed to walls with chromium plated brass screws. Make : Cera cat part No F5013106CH or equivalent in Jaquar/Kohler

S&F in repair soap dispenser fixed to walls with chromium plated brass screws. Make : Cera cat part No F5013111CH or equivalent in Jaquar/Kohler

S&F in repairs CP brass hot & cold single lever basin mixer with 450mm long braided hoses cast copper alloy with centre hole for WHB complete all as directed by Engineer-in-charge. Make : Jaquar Opal Prime Series/ Cera Ruby series/Kohler

S&F in repairs CP brass hot & cold 15mm dia wall mixture for mixing hot & cold water with shower provn with connecting legs & flanges complete all as specified. Make : Jaquar Lyric or Aria Series/ Cera Ruby series/Kohler

S&F in repairs CP brass hot & cold 15mm dia single lever sink mixer swinging spout (wall mounted model) with connecting legs & wall flanges complete all as specified. Make : Jaquar lyric or Aria Series/ Cera Ruby series/Kohler

S&F Sink made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement morter on to dwarf wall or inclulding fixing cantilever brackets and connecting union to pipe overall size 405mm x 460mm x 203 mm bowl size 405 mm x354mm x 203mm fixed in repair complete all as specified and directed. Make :- Prayag Cat part No.1216DM or equivalent in Blue star/Nirali.

S&F in repairs 15mm bore long body bib tap chromium plated fancy type with wall flange and aerator complete all as specified and directed. Make : Jaquar Opal Prime Series/ Cera Ruby series/Kohler.

S&F in repairs CP fancy type Angle valve 15mm dia (angle cock) cast copper alloy with wall flange. Make : Jaquar Opal Prime Series/ Cera Ruby series/Kohler

S&F in repairs CP fancy type twin Angle valve 15mm dia (angle cock) cast copper alloy with wall flange. Make : Cera cat part No F1016211 or equivalent in Jaquar/Kohler

S&F in repair CP brass overhead rain shower with extension CP Arm pipes. Make : Cera cat part No F7010213AB or equivalent in Jaquar/Kohler

S&F in repair CP Health faucet telephonic type with 1.5m long flexible pipe. Make :- CERA/Kohler

S&F in repair brass chromium plated towel rail, 600mm long. Make : Cera cat part No F5013103CH or equivalent in Jaquar/Kohler

S&F in repair brass chromium plated towel ring fixed with screw in wall complete all as specified and directed.Make : Cera cat part No F5013115CH or equivalent in Jaquar/Kohler

S&F in repair brass chromium plated towel rack with hooks, 60cm long between flanges complete all as specified and directed. Make : Cera Cat Part No F5015131CH or equivalent in Jaquar/Kohler.

S&F of tooth brush/paste tumbler holder fixed to walls with chromium plated brass screws. Cera cat part No F5013107CH or quivalent in Jaquar/Kohler

S&F in repairs of Coat hook (set of 06) fixed to walls with chromium plated brass screws. Cera cat part No F5003113 or equivalent in Jaquar/Kohler

S&F in repairs for urinals star white colour size of 375x390x590 mm (mimimum) with grating and union of discharge pipe complete including providing and fixing plugs PVC waste pipe bedding urinal agaisnt wall in cement mortar 1:2 securing urinal to plugs PVC waste pipe with and including 60mm long brass screws, pointing around urinal back in cement etc complete all as specified and directed by Engr-in-charge. Make : Cera cat part No S4020112 or equivalent in Jaguar/Kohler

S&F PVC (SWR) 110mm dia pipes single socketed, in any length with rubber ring joints, fixed to walls/floors fixed in repair complete all as specified and directed.

S&F PVC (SWR) 75mm dia pipes single socketed, in any length with rubber ring joints, fixed to walls/floors fixed in repair complete all as specified and directed.

S&F PVC bends fitted with oval access doors 75 mm dia any radius diminishing pieces or tapers fixed in repair complete all as specified and directed.

S&F PVC bends fitted with oval access doors 110 mm dia any radius diminishing pieces or tapers fixed in repair complete all as specified and directed.

S&F PVC (SWR) bends of 75 mm dia any radius diminishing pieces or tapers fixed in repair complete all as specified and directed.

S&F PVC (SWR) bends of 110 mm dia any radius diminishing pieces or tapers fixed in repair complete all as specified and directed.

S&F PVC (SWR) floor trap 100mm dia, plain with grating including jointing with solvent cement fixed in repair complete all as specified and directed.

S&F in repair Grating square fitting of size 150mm made in two parts for smell and mosquito proofing with hole for waste pipe complete all as specified and directed.

M&L for Cutting chases, pining in, making good to facings where reqd and pointing in cement motor (1:3) to ends or edges of landings, steps, cills, sunsheds, shelves, lintels, etc, and cutting chases for concealed water tubing or concilled conduit wiring, etc and making good exceed 20 cm girth in brick walls complete all specified and directed

S&F 15mm bore medium grade steel water tubing, galvanized (ISI Marked) with and including all fittings (ISI Marked) and jointed, tested and fixed complete to wall and ceiling or laid in floors etc complete including taking up or down existing steel tubing pipe complete all as directed.

S&F 20mm bore medium grade steel water tubing, galvanized (ISI Marked) with and including all fittings (ISI Marked) and jointed, tested and fixed complete to wall and ceiling or laid in floors etc complete including taking up or down existing steel tubing pipe complete all as directed.

S&F 1000 Litres capacity rotational moulded polyethylene water storage tanks, three layered, ISI Marked (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I-2009 including 20mm dia GI light grade washout pipe 50mm long with plug and 20mm dia GI light grade over flow pipe 600mm long with fitting including dismantling of existing unserviceable tank and removing from site complete all as specified and directed

S&F Ball valve 15/20mm dia high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball min weight 210 gms fixed in repair complete all as specified and directed. Make:- Cera, Prayag, Polytuff.

M&L Drapery rod in any length, high strength stain less steel pipe having outer dia 25-28mm a pair of brackets & a pair of stainless steel finials, fixed in repair complete all as specified and directed.

S&F Pre- painted colour galvalume aluminium Zinc coating GI based tile profile corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa and 150 GSM as in roof covering/cladding to wall, fixed with self tapping screws etc fixed in repairs complete all as directed.

S&F Pre-painted colour galvalume aluminium Zinc coating AZ 150 GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws etc fixed in repairs including dismantling complete all as directed.

S&F Pre-painted colour galvalume aluminium Zinc coating AZ 150 GI based pre profiled (matching with roof sheet) plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridges, gutter fixed in repairs complete all as directed by Engr-in-charge.

S&F Rolled structural mild steel work as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed.(Fe-410-W(Gde E- 250) quqlity B)

M&L for Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

M&L for 15mm thick ready mix external cement plaster on brick, concrete surfaces and Ceiling including providing & mixing water proofing compound as per manufacturers specification, surface finished even & fair, finishing curing scaffolding including taking down of existing cement plaster etc complete all as specified and directed. Make : ACC (Suraksha)/Ultratech(Readyplast)/Birla (Aerocom).

M&L for Brick work with sub class 'B' bricks (old size) straight or curved on plan exc 6.00m mean radius built in cement mortar (1:6) including demolition of existing brick work and removal out side IMA premises complete all as specified and directed.

Demolition of cement concrete in ground floor and paving nexc 15cm thickness (below or above ground level)

M&L for 75mm thick PCC 1:3:6 type C-2 using 20 mm graded crushed stone aggregate as in plinth protection or similar places, and finishing the surface even and smooth without using extra cement including making joints 12mm wide to the full depth of PCC at every 3 meters and at every change of direction and filling the same with sealing compound grade 'A' including necessary formwork etc complete all as specified and directed.

M&L for 40mm thick PCC type B1 1:2:4 (20mm graded crushed stone aggregate) as in floors and finishing the concrete even and smooth using extra cement complete all as specified and directed.

M&L for Preparation of wood or wood based materials new or old of any description and girth and treated with two coat of creosote complete all as specified and directed

M&L for Preparation of puttied wall / ceiling by mechanical sander/grinder and applying two coats of oil bound emulsion distemper over a coat of primer complete by using mechanical sander/grinder over a coat of 2 to 3mm thick acrylic damp proof wall care putty as per manufacturers instruction all as specified and directed. Note : 1. The work shall be executed from authorized applicator as approved by GE. 2. After completion of distempering, contractor have to carry out following work whose rates to be included while quoting the rates. No extra payment will be done on this account and damage if any to be borne by the contractor :- (i) cleaning of floor with floor cleaner and stain should be removed from wall/door/jaali. (ii) cleaning of fan after removing and refixing the same. (iii) cleaning of curtain rod. (iv) shifting of furniture.

M&L for Preparation of surfaces of wall / ceiling (new/old) either by complete removal of existing treatment on new surface and applying two coats of weather coat exterior paint over a coat of primer complete all as specified and directed. Note : The work shall be executed from authorized applicator as approved by GE

M&L for Preparation of old surfaces of wall / ceiling by mechanical sander/grinder and applying one coats weather coat exterior paint complete all as specified and directed. Note : The work shall be executed from authorized applicator as approved by GE.

M&L in repair for 18/19mm thick one side prelaminated colour WPC board for cup board shutter and frame & fixed at site complete all as specified and directed. Note :- Board edges properly finished with strip on band edges. Color as approved by GE.

M&L for 18/19mm thick white WPC board for cup board shutter and frame & fixed at site complete all as specified and directed. Color as approved by GE.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flap 30 mm complete all as specified.

S&F Auto closing hinges 35 mm of 0 crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters fixed in repair complete all as specified and directed. Make :Hexa, Hettich, Hafele

S&F Stainless steel handles 100 mm size for kitchen cabinet shutters fixed in repair complete all as specified and directed. Make : Hexa, Hettich, Hafele

S&F Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 kgs fixed in repair complete all as specified and directed. Make :Hexa, Hettich, Hafele

S&F Chromium plated stainless steel wire basket (storage basket) pull out type for large utensils, size 480 x 500 x 150 mm of Grade 304 with necessary fixing clips etc fixed in repair complete all as specified and directed. Make :Hettich, Hafele, Butterfly

S&F Chromium plated stainless steel wire basket (cup and saucer basket) pull out type, size 380 x 500 x 100 mm Grade 304 with necessary fixing clips etc fixed in repair complete all as specified and directed. Make : Hettich, Hafele, Butterfly

S&F Chromium plated stainless steel wire basket (plate basket) pull out type, size 380 x 500 x 100 mm Grade 304 with necessary fixing clips etc fixed in repair complete all as specified and directed. Make :Hettich, Hafele, Butterfly

S&F Chromium plated stainless steel wire basket (cutlery basket) pull out type, size 380 x 500 x 100 mm Grade 304 with necessary fixing clips etc fixed in repair complete all as specified and directed. Make : Hettich, Hafele, Butterfly

S&F Chromium plated stainless steel wire basket (Grain Trolley) pull out type, size 480 x 500 x 200 mm Grade 304 with necessary sliding frame structure, fixing clips etc fixed in repair complete all as specified and directed. Make : Hettich, Hafele, Butterfly

S&F Chromium plated stainless steel wire basket (Bottle pull out) pull out type two self, size 120 x 500 x 432 mm with necessary sliding frame structure, fixing clips etc fixed in repair complete all as specified and directed. Make : Hettich, Hafele, Butterfly

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including cutting chasing in brick work and half rounding of exposed edgess including taking down existing shelf and cutting chasing and repair for inserting shelfs complete all as specified and directed.

Taking down any type of door fittings complete all as directed.

M&L for PCC 1:2:4 type B-2 using 20mm graded crushed stone aggregate as in surface channels and drains including Desludging/ cleaning of open drain of any depth by mechanically means and burring the sludge into the ground complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and directed.

S&F in repairs PVC sandwich wall /ceiling lining consisting of 5 mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification complete all as specified and directed.

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Color as approved by GE.

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Color as approved by GE.

S&F in repair Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 75 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Color as approved be GE.

S&F factory made single extruded WPC (Wood Polymer Composite) solid both side prelaminated decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. Color as approved by GE.

M&L 35mm thick factory made solid WPC (Wood plastic composite) moulded gauged door shutter (single door piece to be used) with wire mesh in any number of division with brown wood grain texture, including stainless steel wire shall mesh be fixed with 15x15 Square tube in side rails with screwing 8x28 heat metal zink coated screws can be remove or fix again after changing of wire mesh when needed. The density shall be as per manufacturer instruction complete all as specified and complete all as specified and complete all as specified and directed. Color as approved by GE.

S&F 300mm mild steel ordinary rat tail rod pattern spring including roller and roller plate fixed to wooden/mild steel chowkhat complete all as specified and directed.

S&F stainless steel wire cloth 0.40mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks/wooden beads or galvanized wire staples complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frames) area n exc 1.5 Sqm each complete all as specified and directed

Taking down chowkhats or frame with shutters (without taking off shutters from the frames) area .exc 1.50 Sqm and n exc 4.00 sqm each complete all as specified and directed

M&L for aluminum alloy powder coated standard hollow section as mentioned below window frame (Bombay sliding) with two glazed shutter and one Nos wire gauged shutter sliding type, with aluminum sections as per Series-B (18mm) 3 track of Jindal section numbers for sliding windows, and glazed with & including tinted glass coloured 6mm thick, fixed with glazing clips, rubber beading / gasket anodised beading, screw and lock type 2 Nos aluminium handle of size 75mm and locking system including aluminium grill of 5mm thick, average width of aperture 50mm and SS wire cloth 0.46mm dia of wire and 1.40 aperture with provision of space for AC etc complete all as specified and directed. Shutter Top & bottom size : 52.00 X 18mm X 1.45mm Section No 20737 Shutter inner lock size : 40.00 X 18mm X 1.55mm Section No 20736 Chowkhat bottom/ Top size : 92.00 X 31.75mm X 1.50mm Section No 20832 Chowkhat both sides size: 92.00X31.75mm X 1.50mm Section No 20831

S&F Steel ventilator factory made with centre hung shutter including hinges and steel peg stay complete with glazing bars dovetailed or welded complete all as specified and directed as per drg No TD 088 Sheet 1/17 to 17/17.

S&F 4mm thick sheet glass ordinary quality & glazing with oil putty in squares not exc 0.5 Sqm in each pane complete all as directed.

S&F 4mm thick frosted sheet glass ordinary quality & glazing with oil putty in squares not exc 0.5 Sqm in each pane complete all as directed.

S&F Mild steel framed work such as grills, grating etc with end of bars shouldered and/ or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing and similar work complete all as specified and directed

S&F Butt hinges, 100 mm long, extruded stainless steel with galvanised mild steel hinge pin anodised and fixed complete all specified as directed

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed

S&F 150mm extruded aluminium alloy handles, fabricated type, complete all as specified and directed.

S&F 200mm long aluminium anodized, barrel tower bolts of extruded section complete all as specified and directed

S&F implemental safety door viewer/magic eye along with its accessories fixed in door complete all as directed.

M&L for PCC 1:3:6 Type C-2 (using 40mm graded crushed stone aggregate) as in foundation of man hole incl demolition of existing cement concrete of any description complete all as specified and directed.

M&L for Cleaning the manhole up to 1.50m deep by rodding manually and removing the sludge from manhole and completely cleaning by flushing with water etc complete , sludge shall be buried into ground and throwing the enough quanity of lime to stop the foul smell complete all as specified and directed.

M&L for Cleaning the sewage line over 150mm dia and upto 250mm dia by rodding manually and removing the sludge and completely cleaning by flushing with water etc complete , sludge shall be buried into ground and throwing the enough quanity of lime to stop the foul smell complete all as specified and directed.

M&L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear mtr including drilling and plugging holes etc. in apron.

S&F 4mm thick E-board false ceiling (Classic) including galvanised colour coated snap grid frame for false ceiling, size of grid 605x 605mm fixed with 1.6 mm dia GI wire suspenders one end tied to roof members and other end connected to main tee of grid framework by means of 4mm dia adjustable "J" hook consisting of two Nos washers and two nuts at 1.2 mtr centres, size of main tee 38mmx25mmx 1.4mm, cross tee 38 mmX25 mmX1.4mm, angle along walls 38 mmX 25mmX2.0 mm and including taking down existing boards any thickness including cover fillets etc complete all as directed.

M&L for Repairing to existing door/ window chajjas upto 3.0m span and width 1.0m by demolition/ scrapping of damaged portion and preparing the surfaces by providing 50mm thick cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate including finishing the surface by rendering 10 mm thick plaster in CM 1:3 and finished even and smooth surface using extra cement over concrete surface and PCC benching including weathering sliglitely rounded or chamfered angles and throating over and including priming newly plastered/concrete surface by applying one coat of primer, 2 mm thick acrylic damp proof wall care putty and applying two coat of Apex paint (Weather coat exterior paint) and complete making good existing disturbed surface all as specified and directed (work to be carried out upto a height of 7.5 m and rate shall be inclusive of all necessary scaffolding and shuttering). Note: Reinforcement if required shall be measured and paid separately.

M&L for obliterating old writing of any description, n exc 01 sqm with black paint in the form of diamond shape of size not exc 30x30cm and writing letters or figures (Block, Roman Italic or Indian), stops, commas, short lines, dashes, hyphens, brackets etc minimum of 10 cm height (total letters not exc 06 Nos) colour as decided by Engr -in charge complete all as specified and directed (work to be carried out upto a height of 7.5 m and rate shall be inclusive of all necessary scaffolding).

S&F in repair Factory made heavy duty precast RCC Manhole cover confirming to IS 12592 (Part -1 & II) of size 1200mm x 450 mm x 75mm of M-30 Grade of concrete and suitably reinforced with strong vibrating compaction by vibratory table including providing MS hook duly black painted, complete all as specified and directed. Make:- Tulip Infrastructure, Jain tiles Haldwani, NTC Panchkula.

S&F in repair Factory made Precast plain / perforated RCC Drain/ manhole cover of size 900x 450 x 50 mm of M-30 grade of concrete reinforced with 8 mm dia TMT bar of Fe- 500 grade at 150 mm c/c spacing both way with strong vibrating compaction by vibratory table including providing MS hook duly black painted complete all as specified and directed. Make:- Tulip Infrastructure, Jain tiles Haldwani, NTC Panchkula.

S&F in repair Factory made heavy duty Precast plain / perforated RCC Drain/ manhole cover of size 450x 450 x 50 mm of M-30 grade of concrete reinforced with 8 mm dia TMT bar of Fe- 500 grade at 150 mm c/c spacing both way with strong vibrating compaction by vibratory table including providing MS hook duly black painted complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surface of walls, floors, etc.

Taking down water Heater of any capacity and make serviceable by replacing unsv part including descaling the inner container with cleaning solution including preparation of old painted surface body of geyser of any capacity ,cleaning foreign material ,filling cavaties atc and painting with one coat of synthetic enammeled paint by spray painting and marking MES No. with paint and kept in safe custody for reuse at site after compltion of wiring work.

Taking down the existing Energy meters carefully and proper noted down the qtr No Meter No and reading with date and kept in safe custody for re-fixing at site after compltion of bldg work complete all specified and directed.

Taking down old U/S main switches, Sheatmetal enclosures DB including MCCBs, MCBs etc including making good to the disturbed surface of wall all as directed.

Taking down old unsv T/L, Lamp,Security light of any size and capacity

Taking down carefully submain wiring including all accessories without disturbing existing wiring fittings fixtures etc and making good to the disturbed surfaces all as directed and as specified in any type and size all as directed.

Material and labour for point wiring with PVC insulated and unsheathed electric cable 1100 volts grade single core FRLSH having multi stranded copper conductor of 1.5 sq mm nominal cross sectional area drawn in Non metalic pvc not less than 25mm dia concealed in wall with all fitting and fixing accessories and 1.5 sq mm PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor, connected to earth dolly by providing suitable lugs with & including modular metal flush box of required size factory made for mounting Modular switch, regulators etc with and including Modular cover and frame , ISI marked, for the following including taking down old unsv point wiring with connected accessories. Make of wire:Havells/ Polyacab /Grandlay/ SCI Make of conduit: AKG Plastic Pvt Ltd./Bhagwati Plastic & Agriculture industry /Polycab Note : (i) Point wiring & earth wire shall be connected to each & every sunken box. (ii) All screws, fasteners, bolts, nuts & washer shall be cadmium plated & the cost of which is deemed to be included in the quoted unit rates.

One light point controlled by one, one way switch 5 Amps

One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board.

One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

One bell point controlled by one, bell switch 5 Amps

All as per item No.109 above but with stranded copper conductor 2.5 Sq mm (nominal area), two single core, PVC insulated cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet, independent, including PVC insulated stranded copper conductor 2.5 Sqmm (nominal area) single core as earth continuity conductor to common earth and connecting to earth dolly.

Supply and fix modular switch 1 way 6A, 1 Module Make:Havells ORO(White)/Legrand Lyncus/Indoasian(Glint)

Supply and fix modular switch 1 way 16A, 1 Module with indicator lamp Make:Havells ORO(White)/Legrand Lyncus/Indoasian(Glint)

Supply and fix modular bell push 6A, 1 Module Make:Havells ORO(White)/Legrand Lyncus/Indoasian(Glint)

Supply and fix modular socket 6A, 2/3 pin combined 2 Module Make:Havells ORO(White)/Legrand Lyncus/Indoasian(Glint)

Supply and fix modular socket 6A/16A, 2/3 pin combined 2 Module Make:Havells ORO(White)/Legrand Lyncus/Indoasian(Glint)

Supply and fix modular fan regulators step type 2 module 120W Make:Havells ORO(White)/Legrand Lyncus/Indoasian(Glint)

Material and labour for ceiling rose, 63.5 mm dia, ISI marked, three terminal of polycarbonate/isolated body complete all as directed. Make: Anchor, Crab tree, SSK

Suply and fix for Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed

Supply and Fix in rapiar LED Up Down twin glow 20W + 20W light fitting of lumens 2000 lumens wall mounted ,high pressure die cast alluminium, fully diffused ,polycarbonated diffuser,system efficacy 100L/W , IP-20 ,high bright LED lamp, colour temp not less than down 6500/ up 3000 Cool Day Light/warm light ,colour rending index not less than 80 ,life not less than 35000 hrs, inbuilt electronic driver, PF not less than 0.90 and THD less than 20 % with operating voltage 160-360V AC, 50 Hz, surge protection minimum 2.5 KV, including connected the same with using PVC sheathed , insulated 3 core flexible 23/0.0076 copper cable including fixing arrangement for fixing the light fitting to ceiling rose complete all as specified and directed. Make: - PHILIPS /CROMPTON/HAVELLS

Supply only LED batten light fitting of lumens 1200 lumens wall mounted ,high pressure die cast alluminium, fully diffused ,polycarbonated diffuser,inbuilt electronic driver IP-20 ,high bright LED lamp, colour temp not less than 5700 COOL DAY Light,colour rending index not less than 80 ,life not less than 20000 hrs, inbuilt electronic driver, PF not less than 0.90 and THD less than 20 % with operating voltage 140-270V AC, 50 Hz, surge protection minimum 2KV all as specified and directed . Make: - PHILIPS/HAVELLS/CROMPTON

S& F in repair metal finished bed side lamp grey in colour 20 Watt /50 Lumens/3000K, base of the lamp should be E27 and dimension of fitting 470x67x28 mmand connected the same with using PVC sheathed and insulated 3 core flexible 23/0.0076 copper conductor cable including all accessories and fixing arrangement for fixing the light fitting to wall including taking down existing fitting complete all as specified and directed. Make: Philips /Crompton/Havells

Supply and fix Metal finish wall light with maximum bulb wattage 12 watt, base of the lamp should be E27, colour of the fixture is white & silver wsith chrome finish and having rectanguar shape for aesthetic look. dimension of the fixture should be 100 x 125 x 200 mm and connected the same with using PVC sheathed and insulated 3 core flexible 23/0.0076 copper conductor cable including all accessories and fixing arrangement for fixing the light fitting to wall including taking down existing fitting complete all as specified and directed. Make: Philips /Crompton/Jaquar/Havells

Supply and Fix in repair LED street/Security wall mounted light fitting of lumens 2550 lm ,Single Piece High pressure die cast aluminium,system efficacy 1100L/W,Epoxy powder coated with any additional treatment for smooth and anti corrosive finish, fully diffused ,Polycarbonated Cover for More protection ,inbuilt electronic driver IP 66 ,High bright LED with Lens, colour temp Not less than 5700 Cool Day Light,colour rending index not less than 70 ,life not less than 50000 hrs,inbuilt electronic driver with 325V Auto Cut off Restart feature & 440V Phase to Phase protection till 8 hour, PF not less than 0.95 and THD less than 10% at full load with operating voltage 140-270V AC, 50 Hz ,surge protection minimum 4 KV, including connected the same with using PVC sheathed , insulated 3 core flexible 23/0.0076 copper cable including fixing arrangement for fixing the light fitting to ceiling rose including taking down old unsv light fitting complete all as specified and directed. Make: - PHILIPS /CROPTON/HAVELLS

Supply and fix ceiling Fan complete with blades,down rods ,230 volts ,1200 mm sweep ,min air delivery 210 CFM with service value 6.00 BEE ,with Brushless direct current motor (BLDC) including taking down non BLDC fan and deposited to the MES store. Make:-

S & F sub main wiring with PVC insulated unsheathed FRLSH cable 1100 Volt grade, with multi stranded copper conductor drawing in existing Concealed conduit including one run PVC insulated unsheathed cable with multi stranded copper conductor as a earth continuity and connected upto DB of following sizes complete all as specified and directed. Note:Two run of single core PVC cable with one run of earth conductor & condiut shall be measured as one unit. Make:- Havells, Anchor, SCI, Grandlay

(a) 2 x 10 Sqmm + 1 x 10 sqmm (From Main DB to Sub DB of Qtr )

(b)2 x 4 + 1x4 Sqmm ( For AC& geyser Sub main )

Supply and fix exhaust Fan ,made of sturdy Engineering plastic complete with louvers shutter,voltage 230volts ,50HZ,RPM 1200,copper winding of sweep 250 including cutting holes on wall and making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. Make:- Crompton,Orient, Havells.

S&F Water heater (Geyser) storage type, electric,capacity 25 litres five star rated AC SP 230 volts, 50 Hz, vertical mount type, shockproof and rustproof metal body, stainless steel inner container, high efficiency heating element, autocut thermostate, pressure release safety system,NRV , fire retardent cable with 3 pin plug top,PVC conncetion white colour including fixing accessories like fastensers, nuts, washers including taking down old unsv geyser and deposited to MES store complete all as specified and directed. Make:- Crompton,Bajaj, Havells(Adonia series).

Material and labour for earthing with galvanised steel earth plate electrode 60cmX60cmX 6mm thick burried directly in ground (earth pit not less than2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to 4mm thick GI wire by means of nuts,bolts,check nuts & washers of galvanized iron or steel,protected by 15mm bore light grade galvanised iron pipe and connected to main switch board,including all necessary excavation & earth work in hard dense soill including funnel with wire mesh and watering pipe 20 mm bore medium grade galvanised iron pipe with charcoal and common salt in alternate layers of 15 cm thickness all around the GI plate electrode with concrete pit in PCC 1:3:6 type C-1 with cast iron frame including cast iron cover10mm thick hinged to CI frame and 6mm MS rod for handle and necessary testing complete all as shown in electrical plate No 3 of SSR part-I all as specified and directed.(one earthing for each main Panel )

Fixing only and connecting up electric meter taking down against item No 105 here in before

S and F sheet metal enclosure double door type ISI marked MCBs DB SPN(Single pole and neutral) 240V AC 16 way with 200 Amps rated bus bar all as specified and directed Make:- Havells, Indo Asian, HPL

S and F sheet metal enclosure double door type ISI marked MCBs DB SPN(Single pole and neutral) 240V AC 8 way with 200 Amps rated bus bar all as specified and directed. Make:- Havells, Indo Asian, HPL

S & F REO modular AC MCB box protected socket PVC Plastic base three- Module including 25 Amps Plug top and MCB 25 Amps Fixed in repair complete all as specified and directed Make:- Havells, Indo Asian, HPL.

S and F 240 Volts ,10KA” B” curve miniature circuit breaker (MCB SP) of single pole/double pole of folowing current carrying capacity in the MCB DB complete with connection testing and commissioning all as specified and directed. Make:- Havells, Indo Asian, HPL.

MCB SP 240 volts, 50 Hz capacity 6-32 Amps

SPN 240 volts, 50 Hz capacity 63 Amps

S & F in repair Distribution boards epoxy powder coated TP & N (VTPN MCCB DB) fabricated from minimum 1.6 mm thick CRCA sheet and fixed/ flush to wall and suitable for universal mounting with 250 Amps fully insulated copper Bus Bar for each phase and 02 neutral shrouded bar ,2 earth bar and cable tie for cable management with reversible door for IP-43 DB,S protection,415 volt ,suitable for fixing FP MCCB 100/125 Amps as incomer and 24 SP MCBs or 4/8/ 12 TP MCBs (or any combination of SP/TP MCBs) outgoings of following capacity and making good the distrubed surface complete all as directed. Note: Suitable MCCB and outgoing MCBs will be measured separately under relavant items of this schedule) Make:- Havells, Indo Asian, HPL.

4 Way VTPN DB (FP MCCB +12 MCB,C). Make :legrand Cat No. 507745 equvilent in L&T, ABB, Schneider

S & F MCCB ,4 pole ICS=100% ICU at 415 volts with rupturing capacity 16 KA with thermal-magnetic release and adjustable overload setting . The MCCB shall have a Mechanical life = 40000 operations & Electrical life = 8000 operations of following capacity complete all as directed. Make:- Havells, Indo Asian, HPL.

Supply and fix concealed in wall Rigid non metalic PVC conduit of , inclusive of boxes (junction/terminal)but inclusive of all tees,bend ,elbow reducers, bell mouth tube ends and fixing acessories such as couplers,lock,nut saddles,pipe hooks all as specified and directed. Make of conduit:- AKG, Bhagwati Plastic, Finolex

20mm dia

S&F Water heater (Geyser) storage type, electric,capacity 3 litres AC SP 230 volts, 50 Hz, vertical mount type, shockproof and rustproof metal body, stainless steel inner container, high efficiency heating element, autocut thermostate, pressure release safety system,NRV , fire retardent cable with 3 pin plug top,PVC connection white colour including fixing accessories like fastensers, nuts, washers complete all as specified and directed. Make:- Crompton,Bajaj, Havells(Adonia series).

Sanjeev Sehgal Contractor

Sharda Enterprises

ANANYA CONSTRUCTION CO.

M/S PUNDIR BUILDERS