C/O SDM residence Type IV Quarter building at Sarahan in tehsil Pachhad Distt. Sirmour (SH C/O Civil works, WS SI C/O Septic tank , Rain harvesting system site Development etc.)

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Supplying and filling in plinth with sand under floors,including watering, ramming, consolidating and dressing complete. as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing form work with steel plates of 3.15mm thick, welded with angle iron in frames of 30x30x5mm so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in foundation,. Footings bases of columns and mass concrete .as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing form work with steel plates of 3.15mm thick, welded with angle iron in frames of 30mmx30mmx5mm,so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings and the like floor etc.as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing form work with steel plates of 3.15mm thick, welded with angle iron in frames of 30x30x5mm,so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers, girders lintels, sides, and soffits of beams haunchings, cantilevers bressumers and lintels upto all depths. as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing form work with steel plates of 3.15mm thick, welded with angle iron in frames of 30x30x5mm,so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in columns, pillars , posts and struts, square, rectangular, polygonal in plain. as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing form work with steel plates of 3.15mm thick, welded with angle iron in frames of 30x30x5mm,so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced plain concrete work in stairs cases with slopping or stepped soffits, excluding, landing,. as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering, strutting and propping etcetera with wooden battens and ballies upto all heights of propping and centring below supporting floors and removal of the same for in-situ-reinforced concrete and plain concrete work in edges of slabs and breaks in floors and walls in all width. as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and laying cement concrete 1:5:10 (One cement: five sand: ten graded crushed/broken stone aggregate 40mm nominal size and curing complete, excluding cost of form work in foundation and plinth.as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and laying cement concrete 1:6:12 (One cement: Six sand: Twelve graded broken/crushed stone aggregate 40mm(forty millimeters nominal size) mechanically mixed and curing complete, excluding cost of form work in foundation and plinth.as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering,finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size)as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1cement : 1.5 coarse sand) : 3 graded stone aggregate20 mm nominal size).as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Steel reinforcement for reinforced cement concrete work including strengthening, cutting, bending, binding and placing in position complete and binding all complete avobe plinth level TMT bar grade Fe-500as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand): 4 graded stone aggregate 12.5mm nominal size)as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil. as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :CM 1:6 as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.with CM 1:4as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with :Cement mortar 1:6 (1 cement : 6 coarse sand)as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Coursed rubble masonry (first sort) with hard stone in foundation and plinth with :with :Cement mortar 1:6 (1 cement : 6 coarse sand)as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing wood work in frames of doors, windows, clearstory, windows and other frame wrought, framed and fixed in position.2nd class DD wood as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete asn per the direction of Engineer-In-charge.

Providing and fixing flush door shutter interior grade commercial type core of black board construction with frame of Ist class hard wood and well matched commercial ply veneering with vertical grains of cross bands and face veneers on both faces of shutter 35 mm thickas per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing panelled glazed or panelled and glazed shutters for doors, windows and clearstory windows including black enamelled iron but hinges with necessary screws.2nd Class DD Wood as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :35 mm thick as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing factory made 30 mm thick door shutter made of solid PVC foam profile. The styles & rails shall be of size 75 mm x 30 mm having wall thickness 5 mm. The styles, top & bottom rails shall have one side wall thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with M.S. tubes of size 33 mm x 17 mmx 1 mm, painted with primer , all four corners of reinforcement to be welded or sealed. Solid PVC extruded bidding (push fit type) will be set inside the styles and the rails with a cavity, to receive single piece extruded 5mm PVC sheet as panel. The styles and rails will be mitred cut and joint with the help of PVC solvent cement & self driven self tapping screws. Single piece extruded solid PVC lock rail of size 100 mm x 30 mm with wall thickness 5 mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100mm x 8 mm complete as per manufacturer's specifications and direction of Engineer-in-charge.Decorative finish (both side wood)

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete Fixed to steel windows by welding as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :250x16 mm as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :250x10 mm as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete100x10 mm as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing aluminium handles, ISI marked,anodised (anodic coating not less than grade AC 10 asper IS : 1868) transparent or dyed to required colour orshade, with necessary screws etc. Complete 125mm as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing aluminium handles, ISI marked,anodised (anodic coating not less than grade AC 10 asper IS : 1868) transparent or dyed to required colour orshade, with necessary screws etc. Complete 100 mm as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing ISI marked hydraulic spring hinges with necessary screws etc.complete as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing oxidised M.S. casement stays(straight peg type) with necessary screws etc. complete. as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing complete box of cup board shall be made of 25 mm thick water proof tremite resistance commercial board of uniply / green ply/century ply /kit ply/ duraply (ISI marked) back side of cup board shall have 6/8 mm thick water proof ply ( as per detail) .The shutter from all side also have 6 mm thick hard wood edging / lipping all round be finished both side with 1 mm thick lamination of centurry / green / action tesa / mislinous. All cut portion of the round shall have 6 mm thick hard wood edging /lipping cabnit rack/ magnitc , catcher, handle and necessary fitting complete all respect. as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing special quality bright finished brasscupboard or ward robe locks with four levers of approved quality including necessary screws etc. Complete 65 mm as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complete 600x600 mm as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified andas directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing pre-painted sheet roofing of kotar metal single skin trapezoidal 10 (ten) refitted sheeting 0.60mm thickness having 1060mm (one thousand sixty millimetre) cover width cover all width 1126mm, 28mm crest depth at 353mm (three hundred fifty three millimetre) 2.50mm (two decimal fifty millimetre) the main crest with at top 25mm and at lower 81mm base metal of coil rolled steel coil with zinc waiting top coat with regular modified polysters coating of approved shade and balancing reverse coat 5.5mm (five decimal five millimetre) dia and 55mm (fifty five millimetre) length with EPDM seal complete in all respect

Providing and fixing pre-painted sheet ridge or hips 60cm (sixty centimetre) over all of kotar metal skin trapezoidal profiled sheeting 0.60mm cover with over all width 1126mm (one thousand one hundred twenty six) 28mm (twenty eight) crest depth at 353mm (three hundred fifty three) 2mm (two millimetre) C/C crest distance. There will be two ribs at the centre for stiffening heaving crest depth of 2.5mm (two decimal five millimetre) the main crest with at top zinc waiting top coat with regular modified polyster coating of approved shade and balancing reverse coat 5.5mm (five decimal five millimetre) dia and 550mm (five hundred fifty millimetre) length with DPDM seal complete in all respect as per approved drawing design as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing prepainted sheet valleys of 90 cm wide overall in plain G.S. sheet fixed with polymer coated J, or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete : as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing 15 cm wide, 45 cm overall semi circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complet. 0.63 mm thick with zinc coating not less than275 gm/m² as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Bend 110 mm as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion Shoe 110 mm as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing plaing B.P. sheet 1.60 mm (one decimal sixty millimetre) thick 16 SWG fixed in soffits ceiling including jointing with gas/electric welding in position complete (frame work is to be measured paid for separately) as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc. :100 mm as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat ofapproved steel primer all complete. as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

20mm cement plaster in single coat on rough side of brick/ stone masonry for interior plaserting upto floor two level with Cm 1:6as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

20mm cement plaster in single coat on fair side of brick/ stone masonry for interior plaserting upto floor two level with Cm 1:4 as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

6 mm cement plaster to ceiling with Cm 1:3 as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Applying priming coat:With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete. as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Distempering with oil bound washable distemper ofapproved brand and manufacture to give aneven shade:New work (two or more coats) over and including water thinnable priming coat with cement primer as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Finishing walls with water proofing cement paint of required shade New work (Two or more coats applied @ 3.84 kg/10 sqm) as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

P/F stainless steel knock down railing of kich AISI-316 of 38 mm dia handrail fixed on 10x150 mm SS flat Blusters placed at 1200 mm c/c along with 3 nos 16 mm dia mid rails connected at the side bluster with fixture . The blusters would be fixed on to floor with casted base plate of minimum 6 mm thickness base plate shall be concealed with suitable SS 316 grade cover cape ailing height to be taken @ 85 mm form floor level as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing under layer for plinth protection of 75mm thick bed of dry brick/stone aggregate 40mm nominal sizes well rammed and consolidated and grouted with fine sand including preparation of ground. as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing plinth protection 50mm thick cement concrete 1:3:6 20mm nominal size) including finishing the top surfaces of concrete smooth as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Construction course rubble hammer dressed ‘U’ shape open surfaces drain with side wall 15x23cms in cement mortar 1:6 and inside plastering with cement plaster 1:3 including earth work and laying 10cm (Ten centimeters) cement concrete in 1:5:10 40mm) nominal size and 7.5cm cement concrete 1:2:4 20mm nominal size and finished with a floating cost of neat cement complete as per standard design as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings andbrackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for then reception of pipes and fittings.as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required 610x460 mm bowl depth 200 mm as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan.as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings completeas per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing 100mm dia CP iron grating of ESS-KSS for nalhni trap as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. Triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing 600x450 mm beveled edge mirior supperior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc.,complete. as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing chromium plated brass soap dish of Jaguwar or contra with C.P. brass brackets fixed to wooden cleats with C.P. brass screws as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing CP brass long nose 15mm diameters C.P. brass bib tapbib cock of approved quality confirming to IS standred and weighting not less than 810 grams 15 mm nominal bore of Jaguwar or contra with capstan head as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing CP brass stop cock ( concealed) of standred design and app. To confirming to IS 8931 15mm nominal bore as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing uplasticised PVC connection pipe with brass unions 450 mm length 15mm as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing CP brass shower rose with 15 mm diameteras per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing Polyethelene-Aluminium Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge.1216 ( 16mm OD Pipe) Concealed work, including cutting chases and aking good the wall etc.as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing G.I. pipes complete with G.I. Fittings including trenching and refilling etc. :20 mmas per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing G.I. pipes complete with G.I. Fittings including trenching and refilling etc. :15 mm as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and laying cement concrete 1:5:10 (One cement: five sand: ten graded crushed/broken stone aggregate 40mm nominal size in PVC. pipes of the 150 mm internal diameters i/c concrete for bedding necessary form work and curing complete. as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing high pressure PVC spigot and socket soil, waste and ventilating pipes ISI Marked i/c fixing with approved adhesive etc. Complete. 75 mm Dia as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing high pressure PVC spigot and socket soil, waste and ventilating pipes ISI Marked i/c fixing with approved adhesive etc. Complete. 110 mm Dia as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing high pressure PVC spigot and socket soil, waste and ventilating pipes ISI Marked i/c fixing with approved adhesive etc. Complete. 150 mm Dia as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing PVC Single Equal Branch with oval asses ISI Marked insertion rubber washer 3 mm thicK bolt and nuts complete i/c fixing with approved adhesive etc. Complete.75 mm Dia as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing PVC Single Equal Branch with oval asses ISI Marked insertion rubber washer 3 mm thicK bolt and nuts complete i/c fixing with approved adhesive etc. Complete.110 mm Dia as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing PVC floor trap of self cleaning design including fixing with approved adhesive cost of cutting and making good the wall and floor etc. Complete. as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : cement concrete work 1:2:4 (1 cement: 2 Sand 4 graded stone agg.20mm nominal size) as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Coursed rubble masonry (first sort) with hard stone in foundation and plinth with :with :Cement mortar 1:5 (1 cement : coarse sand)as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

15 mm cement plaster in single coat on rough side of brick/ stone masonry for interior plaserting upto floor two level with Cm 1:4as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Stone filling /Brick aggregate under soak pit including entire carriage of materials as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in CM 1:4as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing 455x610mm (four hundred fifty five into six hundred ten millimetre) light duty rectangular C.i. manhole with frame cover weight 38kg (thirty eight kilograms) as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing form work with steel plates of 3.15mm thick, welded with angle iron in frames of 30mmx30mmx5mm,so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Vertical surfaces as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing high pressure PVC spigot and socket soil, waste and ventilating pipes ISI Marked i/c fixing with approved adhesive etc. Complete.110 mm Dia as per H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing and fixing 1.00 Horse Power Water lifting pump i/c all fitting and accessary. as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

Earth work in exacavation for structures as per drawing and technical specifications clause 305.1 including setting out,construction of shoring and bracing removal of stumps and other deterious material and disposal upto lead of 50m,dressing of sides and bottom and backfilling in trenches with excavated suitable material.

Providing and laying plain cement concrete 1:4:8 and curing complete including the cost of frame work for plain/reinforced concrete in retaining walls, breast wall,as per drawings and HP.PWD specifications including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Providing weep holes in brick masonry/stone masonry/plain, reinforced concrete abutments, wing walls, return walls with 100mm dia PVC pipe extending through the full width of the structure with slope of 1(v):20(H) towards drawing face complete as per drawings and technical specifications clause 614,709,1204.3.7 as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Backfilling behind R/wall and wing wall complete as per drawings and technical specifications clause 1204,.3.8. (1) Granular Material. as per direction of Engineer-in charge and H.P. PWD. Specification, including carriage of all labour, equipment's and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Niom Infra Private Ltd

BHARDWAJ CONSTRUCTIONS

H.N.Bhardwaj