Construction of Additional Record Room In Prant Office At Idar (Pro. Furniture Work)

Item Rate In

(with brief specification and reference to book of Quantity Unit Amount

No. figures

specifications)

1 SLOTTED ANGLE RACK 20.00 6403.40 Nos

(Providing, and Arranging slotted angle Size: 914 x 450 x

1828 mm made of 40x40x2mm thick rack having load

bearing members made of high strength MS angle with

having six shelving CRCA sheet 20 Gauge, making five

compartment, all the components having powder coating with

thoroughly anti rust treatment including all necessary fixture,

fastners, fittings, labour material machinary etc complete as

seletced and diretced by Engineer Incharge.)

Description of Item

Item Rate In

(with brief specification and reference to book of Quantity Unit Amount

No. figures

specifications)

2 Providing Fixing and arrenging COMPACTOR:- Verticals: Vertical panel consists of 2.00 47975.00 Nos

the front, centre & rear panel will be made out of 22Swg. thick C.R.C.A. Prime

quality steel and designed to take the load of stiffeners in the centre along the height

for additional strength. Shelves: Boltless type shelves will made out of 20Swg.

Thick C.R.C.A. quality steel having 8 folds in each to carry a U.D.L. of 90 to

Kgs. Unit Partition: The centre partition will comprise of a full C.R.C.A. prime quality

24Swg. (0.6mm) to cover back to back of double face units. Back Cover: The

covering made out of C.R.C.A. prime quality wg. (0.8mm) panel type full back cover,

mounted on single face each cupboard. Super Structure: Super structure of the

mobile storage system will be essentially collapsible or knock down type. Each

component of the mobile storage system such as shelves, front panel, end panel,

vertical rear panel, Centre partition etc, will act as an integral member of the Unit as

a whole. Components: The mobile storage system components are designed with

the afety factors of 1 : 1.5 spectively. Raw Material: Prime tested material of IS

C.R.C.A. & IS 10748 H.R.C.A. Fasteners:- All fasteners / notches provided shall be

electro plated galvanized. Safety Features:- (A) Unit Stoppers : - Each mobile

storage unit will be provided with individual unit locking arrangement n built into the

Hand-wheel/ Triangle-Lever of the system. (B) Track Stoppers:- Each system will be

provided with stoppers on either ends of the rails to prevent the mobile storage unit

from moving away off-Track. (C) cenntral Lock: - Each system will be provided with

central lock to enable locking of the entire system with one key. Indexing

rrangement:- Acrylic indexes (250x 150x 2.5 mm thick) will be provided on each

Front panel of the mobile storage system for easy identification and retrieval. Anti

Rust Treatment: All the items will be supplied duly powder coated in the

manufacture work shop Marks if any during the transportation will be touched up at

site to match the surface. All the components will be given 4 stage 7 steps anti

corrosive treatment. Before carrying out powder coating pretreatment to steel

surface will be carried out such as asing, pickling & Phosphate. Degreasing will be

carried out by using caustic soda, soda ash, Bi sodium phosphate & sulphuricmeta-

silicate proper concentration at closely controlled temperature. The component after

degreasing will be rinsed in water Pickling will be carried out subjecting the

component to sulphuric acid solution for a specified time and washing them again

hwater. Phosphating will be carried out by subjecting the components to a treatment

in phosphoric acid tank with sodium bitrate as accelator so that a fine coating is

achieved. The procedure contain in IS-6005 and IS-3618 will be adhere to.

Pasivation is done by subjecting the mponent to dilute chromic acid rinsing. Base

Frame: Base frame will be fabricated in channel type from H.R.C.A. sheet to form a

Channel of Size: 45 x100 x45mm. Guide Rails : The guide rails comprises of solid

round bar of 30mm (Bright bar) press fit in to ‘U’ channel of 10G Prime quality

CRCA sheet The channels will have flanges on either side. This setup is then

anchored to the floor by means of Expansion bolts. Drive Mechanism: Drive

Mechanism will be provided externally supported on special grade antication bearing

to C134 have smooth and effortless movement. Entire mechanism or gear and

sprockets will be incorporated within the front panel provided in the front of the Unit.

(1) Each mobile storage system will have 4 or 6 Nos of Cast Iron wheels of size:

35mm Each Wheel will be Provided with a pair of self aligned heavy duty pedestal

type bearings. (2) The drive Mechanism will comprise of sprocket chain type

arrangement. (3) The chain used will be ½” traction chain of ‘ Diamond’ or ‘Rollon’

make. (4) The mechanism will only be provided on the external front side of the

mobile storage system i.e. effective storage area inside the compactor will not be

urbed. The entire drive mechanism will be concealed from all side from the safety

point of view. Anti Tilt & Anti Skew Arrangement: (Only for Single Face Mobile Units)

Each Single Face Mobile Unit will be Provided with Anti tilt & skew arrangement on

the rear side of the unit. This will prevent the ;unit from Toppling. Anti tilt

arrangement is a very essential arrangement of The Mobile rageSystem, this are a

pair of bearings, suspended from the base unit moving in a Ground rail and guiding

the unit while in motion. driving Wheel:- riving Wheel/ Triangle lever will comprise of

a central hub resting on a pair of roller bearings with 3 insertable arms engaging into

the hub. The entire component will be stainless steel for better finish & longer life.

The central hub will consist of the unit locking arrangement for preventing the unit

from moving when in use. Drive Cover Panel: Made out of 14Swg. Thick C.R.C.A.

prime quality steel and Box type to cover the entire drive mechanism completely.

The drive cover panel will be of full height i.e. it will be of unit height. Final Finish:

Each component of the system shall be treated with rust preventive treatment and

all the components will be Powder coated in required shade from standard range &

hidden components with enamel liquied paint to prevent rust from climatic onditions.

Deviation: Sizes & parameters of technical specifications tolerance 2.5% to 3.0%

allowed. Deviation in design, quality, quantity will not be acceptable.

Sew Single Face Static Unit - 2150 H x 2700 W (900x3) x 475 D (450+25)

Description of Item

Item Rate In

(with brief specification and reference to book of Quantity Unit Amount

No. figures

specifications)

3 Providing Fixing and arrenging COMPACTOR:- Verticals: Vertical panel consists of 6.00 99838.50 Nos

the front, centre & rear panel will be made out of 22Swg. thick C.R.C.A. Prime

quality steel and designed to take the load of stiffeners in the centre along the height

for additional strength. Shelves: Boltless type shelves will made out of 20Swg.

Thick C.R.C.A. quality steel having 8 folds in each to carry a U.D.L. of 90 to

Kgs. Unit Partition: The centre partition will comprise of a full C.R.C.A. prime quality

24Swg. (0.6mm) to cover back to back of double face units. Back Cover: The

covering made out of C.R.C.A. prime quality wg. (0.8mm) panel type full back cover,

mounted on single face each cupboard. Super Structure: Super structure of the

mobile storage system will be essentially collapsible or knock down type. Each

component of the mobile storage system such as shelves, front panel, end panel,

vertical rear panel, Centre partition etc, will act as an integral member of the Unit as

a whole. Components: The mobile storage system components are designed with

the afety factors of 1 : 1.5 spectively. Raw Material: Prime tested material of IS

C.R.C.A. & IS 10748 H.R.C.A. Fasteners:- All fasteners / notches provided shall be

electro plated galvanized. Safety Features:- (A) Unit Stoppers : - Each mobile

storage unit will be provided with individual unit locking arrangement n built into the

Hand-wheel/ Triangle-Lever of the system. (B) Track Stoppers:- Each system will be

provided with stoppers on either ends of the rails to prevent the mobile storage unit

from moving away off-Track. (C) cenntral Lock: - Each system will be provided with

central lock to enable locking of the entire system with one key. Indexing

rrangement:- Acrylic indexes (250x 150x 2.5 mm thick) will be provided on each

Front panel of the mobile storage system for easy identification and retrieval. Anti

Rust Treatment: All the items will be supplied duly powder coated in the

manufacture work shop Marks if any during the transportation will be touched up at

site to match the surface. All the components will be given 4 stage 7 steps anti

corrosive treatment. Before carrying out powder coating pretreatment to steel

surface will be carried out such as asing, pickling & Phosphate. Degreasing will be

carried out by using caustic soda, soda ash, Bi sodium phosphate & sulphuricmeta-

silicate proper concentration at closely controlled temperature. The component after

degreasing will be rinsed in water Pickling will be carried out subjecting the

component to sulphuric acid solution for a specified time and washing them again

hwater. Phosphating will be carried out by subjecting the components to a treatment

in phosphoric acid tank with sodium bitrate as accelator so that a fine coating is

achieved. The procedure contain in IS-6005 and IS-3618 will be adhere to.

Pasivation is done by subjecting the mponent to dilute chromic acid rinsing. Base

Frame: Base frame will be fabricated in channel type from H.R.C.A. sheet to form a

Channel of Size: 45 x100 x45mm. Guide Rails : The guide rails comprises of solid

round bar of 30mm (Bright bar) press fit in to ‘U’ channel of 10G Prime quality

CRCA sheet The channels will have flanges on either side. This setup is then

anchored to the floor by means of Expansion bolts. Drive Mechanism: Drive

Mechanism will be provided externally supported on special grade antication bearing

to C134 have smooth and effortless movement. Entire mechanism or gear and

sprockets will be incorporated within the front panel provided in the front of the Unit.

(1) Each mobile storage system will have 4 or 6 Nos of Cast Iron wheels of size:

35mm Each Wheel will be Provided with a pair of self aligned heavy duty pedestal

type bearings. (2) The drive Mechanism will comprise of sprocket chain type

arrangement. (3) The chain used will be ½” traction chain of ‘ Diamond’ or ‘Rollon’

make. (4) The mechanism will only be provided on the external front side of the

mobile storage system i.e. effective storage area inside the compactor will not be

urbed. The entire drive mechanism will be concealed from all side from the safety

point of view. Anti Tilt & Anti Skew Arrangement: (Only for Single Face Mobile Units)

Each Single Face Mobile Unit will be Provided with Anti tilt & skew arrangement on

the rear side of the unit. This will prevent the ;unit from Toppling. Anti tilt

arrangement is a very essential arrangement of The Mobile rageSystem, this are a

pair of bearings, suspended from the base unit moving in a Ground rail and guiding

the unit while in motion. driving Wheel:- riving Wheel/ Triangle lever will comprise of

a central hub resting on a pair of roller bearings with 3 insertable arms engaging into

the hub. The entire component will be stainless steel for better finish & longer life.

The central hub will consist of the unit locking arrangement for preventing the unit

from moving when in use. Drive Cover Panel: Made out of 14Swg. Thick C.R.C.A.

prime quality steel and Box type to cover the entire drive mechanism completely.

The drive cover panel will be of full height i.e. it will be of unit height. Final Finish:

Each component of the system shall be treated with rust preventive treatment and

all the components will be Powder coated in required shade from standard range &

hidden components with enamel liquied paint to prevent rust from climatic onditions.

Deviation: Sizes & parameters of technical specifications tolerance 2.5% to 3.0%

allowed. Deviation in design, quality, quantity will not be acceptable.

Sew Double Face Mobile Unit - 2150 H x 2700 W (900x3) x 900 D (450+450)

Description of Item

Item Rate In

(with brief specification and reference to book of Quantity Unit Amount

No. figures

specifications)

4 Providing Fixing and arrenging COMPACTOR:- Verticals: Vertical panel consists of 2.00 80396.00 Nos

the front, centre & rear panel will be made out of 22Swg. thick C.R.C.A. Prime

quality steel and designed to take the load of stiffeners in the centre along the height

for additional strength. Shelves: Boltless type shelves will made out of 20Swg.

Thick C.R.C.A. quality steel having 8 folds in each to carry a U.D.L. of 90 to

Kgs. Unit Partition: The centre partition will comprise of a full C.R.C.A. prime quality

24Swg. (0.6mm) to cover back to back of double face units. Back Cover: The

covering made out of C.R.C.A. prime quality wg. (0.8mm) panel type full back cover,

mounted on single face each cupboard. Super Structure: Super structure of the

mobile storage system will be essentially collapsible or knock down type. Each

component of the mobile storage system such as shelves, front panel, end panel,

vertical rear panel, Centre partition etc, will act as an integral member of the Unit as

a whole. Components: The mobile storage system components are designed with

the afety factors of 1 : 1.5 spectively. Raw Material: Prime tested material of IS

C.R.C.A. & IS 10748 H.R.C.A. Fasteners:- All fasteners / notches provided shall be

electro plated galvanized. Safety Features:- (A) Unit Stoppers : - Each mobile

storage unit will be provided with individual unit locking arrangement n built into the

Hand-wheel/ Triangle-Lever of the system. (B) Track Stoppers:- Each system will be

provided with stoppers on either ends of the rails to prevent the mobile storage unit

from moving away off-Track. (C) cenntral Lock: - Each system will be provided with

central lock to enable locking of the entire system with one key. Indexing

rrangement:- Acrylic indexes (250x 150x 2.5 mm thick) will be provided on each

Front panel of the mobile storage system for easy identification and retrieval. Anti

Rust Treatment: All the items will be supplied duly powder coated in the

manufacture work shop Marks if any during the transportation will be touched up at

site to match the surface. All the components will be given 4 stage 7 steps anti

corrosive treatment. Before carrying out powder coating pretreatment to steel

surface will be carried out such as asing, pickling & Phosphate. Degreasing will be

carried out by using caustic soda, soda ash, Bi sodium phosphate & sulphuricmeta-

silicate proper concentration at closely controlled temperature. The component after

degreasing will be rinsed in water Pickling will be carried out subjecting the

component to sulphuric acid solution for a specified time and washing them again

hwater. Phosphating will be carried out by subjecting the components to a treatment

in phosphoric acid tank with sodium bitrate as accelator so that a fine coating is

achieved. The procedure contain in IS-6005 and IS-3618 will be adhere to.

Pasivation is done by subjecting the mponent to dilute chromic acid rinsing. Base

Frame: Base frame will be fabricated in channel type from H.R.C.A. sheet to form a

Channel of Size: 45 x100 x45mm. Guide Rails : The guide rails comprises of solid

round bar of 30mm (Bright bar) press fit in to ‘U’ channel of 10G Prime quality

CRCA sheet The channels will have flanges on either side. This setup is then

anchored to the floor by means of Expansion bolts. Drive Mechanism: Drive

Mechanism will be provided externally supported on special grade antication bearing

to C134 have smooth and effortless movement. Entire mechanism or gear and

sprockets will be incorporated within the front panel provided in the front of the Unit.

(1) Each mobile storage system will have 4 or 6 Nos of Cast Iron wheels of size:

35mm Each Wheel will be Provided with a pair of self aligned heavy duty pedestal

type bearings. (2) The drive Mechanism will comprise of sprocket chain type

arrangement. (3) The chain used will be ½” traction chain of ‘ Diamond’ or ‘Rollon’

make. (4) The mechanism will only be provided on the external front side of the

mobile storage system i.e. effective storage area inside the compactor will not be

urbed. The entire drive mechanism will be concealed from all side from the safety

point of view. Anti Tilt & Anti Skew Arrangement: (Only for Single Face Mobile Units)

Each Single Face Mobile Unit will be Provided with Anti tilt & skew arrangement on

the rear side of the unit. This will prevent the ;unit from Toppling. Anti tilt

arrangement is a very essential arrangement of The Mobile rageSystem, this are a

pair of bearings, suspended from the base unit moving in a Ground rail and guiding

the unit while in motion. driving Wheel:- riving Wheel/ Triangle lever will comprise of

a central hub resting on a pair of roller bearings with 3 insertable arms engaging into

the hub. The entire component will be stainless steel for better finish & longer life.

The central hub will consist of the unit locking arrangement for preventing the unit

from moving when in use. Drive Cover Panel: Made out of 14Swg. Thick C.R.C.A.

prime quality steel and Box type to cover the entire drive mechanism completely.

The drive cover panel will be of full height i.e. it will be of unit height. Final Finish:

Each component of the system shall be treated with rust preventive treatment and

all the components will be Powder coated in required shade from standard range &

hidden components with enamel liquied paint to prevent rust from climatic onditions.

Deviation: Sizes & parameters of technical specifications tolerance 2.5% to 3.0%

allowed. Deviation in design, quality, quantity will not be acceptable.

Sew Single Face Mobile Unit - 2150 H x 2700 W (900x3) x 475 D (450+25)

Description of Item

Item Rate In

(with brief specification and reference to book of Quantity Unit Amount

No. figures

specifications)

5 Providing Fixing and arrenging COMPACTOR:- Verticals: Vertical panel consists of 18.20 4545.00 Rmt

the front, centre & rear panel will be made out of 22Swg. thick C.R.C.A. Prime

quality steel and designed to take the load of stiffeners in the centre along the height

for additional strength. Shelves: Boltless type shelves will made out of 20Swg.

Thick C.R.C.A. quality steel having 8 folds in each to carry a U.D.L. of 90 to

Kgs. Unit Partition: The centre partition will comprise of a full C.R.C.A. prime quality

24Swg. (0.6mm) to cover back to back of double face units. Back Cover: The

covering made out of C.R.C.A. prime quality wg. (0.8mm) panel type full back cover,

mounted on single face each cupboard. Super Structure: Super structure of the

mobile storage system will be essentially collapsible or knock down type. Each

component of the mobile storage system such as shelves, front panel, end panel,

vertical rear panel, Centre partition etc, will act as an integral member of the Unit as

a whole. Components: The mobile storage system components are designed with

the afety factors of 1 : 1.5 spectively. Raw Material: Prime tested material of IS

C.R.C.A. & IS 10748 H.R.C.A. Fasteners:- All fasteners / notches provided shall be

electro plated galvanized. Safety Features:- (A) Unit Stoppers : - Each mobile

storage unit will be provided with individual unit locking arrangement n built into the

Hand-wheel/ Triangle-Lever of the system. (B) Track Stoppers:- Each system will be

provided with stoppers on either ends of the rails to prevent the mobile storage unit

from moving away off-Track. (C) cenntral Lock: - Each system will be provided with

central lock to enable locking of the entire system with one key. Indexing

rrangement:- Acrylic indexes (250x 150x 2.5 mm thick) will be provided on each

Front panel of the mobile storage system for easy identification and retrieval. Anti

Rust Treatment: All the items will be supplied duly powder coated in the

manufacture work shop Marks if any during the transportation will be touched up at

site to match the surface. All the components will be given 4 stage 7 steps anti

corrosive treatment. Before carrying out powder coating pretreatment to steel

surface will be carried out such as asing, pickling & Phosphate. Degreasing will be

carried out by using caustic soda, soda ash, Bi sodium phosphate & sulphuricmeta-

silicate proper concentration at closely controlled temperature. The component after

degreasing will be rinsed in water Pickling will be carried out subjecting the

component to sulphuric acid solution for a specified time and washing them again

hwater. Phosphating will be carried out by subjecting the components to a treatment

in phosphoric acid tank with sodium bitrate as accelator so that a fine coating is

achieved. The procedure contain in IS-6005 and IS-3618 will be adhere to.

Pasivation is done by subjecting the mponent to dilute chromic acid rinsing. Base

Frame: Base frame will be fabricated in channel type from H.R.C.A. sheet to form a

Channel of Size: 45 x100 x45mm. Guide Rails : The guide rails comprises of solid

round bar of 30mm (Bright bar) press fit in to ‘U’ channel of 10G Prime quality

CRCA sheet The channels will have flanges on either side. This setup is then

anchored to the floor by means of Expansion bolts. Drive Mechanism: Drive

Mechanism will be provided externally supported on special grade antication bearing

to C134 have smooth and effortless movement. Entire mechanism or gear and

sprockets will be incorporated within the front panel provided in the front of the Unit.

(1) Each mobile storage system will have 4 or 6 Nos of Cast Iron wheels of size:

35mm Each Wheel will be Provided with a pair of self aligned heavy duty pedestal

type bearings. (2) The drive Mechanism will comprise of sprocket chain type

arrangement. (3) The chain used will be ½” traction chain of ‘ Diamond’ or ‘Rollon’

make. (4) The mechanism will only be provided on the external front side of the

mobile storage system i.e. effective storage area inside the compactor will not be

urbed. The entire drive mechanism will be concealed from all side from the safety

point of view. Anti Tilt & Anti Skew Arrangement: (Only for Single Face Mobile Units)

Each Single Face Mobile Unit will be Provided with Anti tilt & skew arrangement on

the rear side of the unit. This will prevent the ;unit from Toppling. Anti tilt

arrangement is a very essential arrangement of The Mobile rageSystem, this are a

pair of bearings, suspended from the base unit moving in a Ground rail and guiding

the unit while in motion. driving Wheel:- riving Wheel/ Triangle lever will comprise of

a central hub resting on a pair of roller bearings with 3 insertable arms engaging into

the hub. The entire component will be stainless steel for better finish & longer life.

The central hub will consist of the unit locking arrangement for preventing the unit

from moving when in use. Drive Cover Panel: Made out of 14Swg. Thick C.R.C.A.

prime quality steel and Box type to cover the entire drive mechanism completely.

The drive cover panel will be of full height i.e. it will be of unit height. Final Finish:

Each component of the system shall be treated with rust preventive treatment and

all the components will be Powder coated in required shade from standard range &

hidden components with enamel liquied paint to prevent rust from climatic onditions.

Deviation: Sizes & parameters of technical specifications tolerance 2.5% to 3.0%

allowed. Deviation in design, quality, quantity will not be acceptable.

Sew Tracks of Comparaters (Rates/Mtr) 100x50x6mm with 20mm R Shaft (DIRECT

Description of Item

Item Rate In

(with brief specification and reference to book of Quantity Unit Amount

No. figures

specifications)

6 ROLLER CURTAIN 22.00 1717.08 Sqmt

Providing and fixing of approved quality roller blinds using

phifer fabric of premium grade, with roller tube, bottom bar

leveller made of extruded aluminium alloy an Idler, Insert

Type- Brackets, PVC chain etc. all complete at all floor and

heights as per approved specification. Roller Tube Control,

Clutch, Idler Side by side or single Roller Tube of extruded

Aluminium 38mm inner dia - 41mm outer dia minimum wall

thickness of 1.6mm.

Roller blind - roller blind fabric should be made up of 35%

FibreGlass, 65% PVC, it should have specific low emissivity

treatment and lead free with Greenguard gold certification. It

should have 3% to 5% openness, fabric thickness should be

0.43 mm, mesh weight approx 400 gms/ sqmtr. It should cut

UV rays, with antimicrobial properties preferably with

Microban. The fabirc should be Flame retardant and Lead

Free. It should be GreenGuard certified with Gold Standard

for low chemical emissions for indoor use. (Basic rate of

Roller blinds- 85 rs/sq.ft.) including all accessories, material,

labour, installation etc.. and complete the work satisfactorily

as per instruction of architect or Engineer-in charge.

Description of Item

Item Rate In

(with brief specification and reference to book of Quantity Unit Amount

No. figures

specifications)

7 SOFA 3 SEATER 2.00 16665.00 Nos

Providing and fixing 3-seater sofa,as per drawings or

molded foam,and high density fom warwick brand rexine (as

corner legs with 5 years warranty and instructions provided,

and ,and complete the work satisfactorily as per instruction of

architect or Engineer-in charge.. (appox lenght of sofa is

6'6'') BASIC RATE 3500/RN FT. BRANDS : SHEARLING

SEDUS , NATUZZI or equivalent.

Total Rs.

Rupees Eleven Lakh ThirtySeven Thousand Six Hundred SixtyFive and Paisa SeventySix Only

I / We am / are willing to carry out the work at ________________________________% above / below

percent (should be written in figure and words) of the estimated rate mentioned above. Amount of my / our

tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct_________% Below Add_________% Above

Net Rs.__________________ Net Rs.__________________

In words __________________ In words __________________

1 The Contractor shall exhibit a board with detailed specification and details of work as directed by the

Engineer-In-Charge for which no extra payment shall be made.

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3 GST and Income tax TDS will be deducted at a source while making payments of bills.

4 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.:

PRC-10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C.

items where there is a change as per actual mix design the cost of difference of cement consumption

have been deducted from the rate of original item at the rate of input rate mentioned in all the tender.

Signature of Contractor

Deputy Executive Engineer Executive Engineer

R.& B. Sub Division R.& B. Division

Idar Himatnagar