PROVN OF TOILET BLOCK WITH WC , URINAL POT, WASH HAND BASIN, PATHWAY/PAVED AREA, VEH PARKING SHED WITH HARDSTANDING FOR SIX X LT VEHS,SHED IN FRONT OF BLDG NO-27, SMALL ARMS SHOP, FALSE CEILING, CYCLE STAND, GATE WITH CONCRETE PILLARS, ROOF TREATMENT

Amount

Surface dressing in soft loose soil n exc 15 cm deep and getting out.

Excavating in trenches n.exe. 1.5 m width and n.exe. 1.5 m in depth for foundation in soft/loose soil & getting out..

Returning filling in , including spreading,levelling,watering & well ramming in layers not exc 25 cm.

Removing excavated material n exc 50 m & depositing where directed at a level n exc 1.5 m.

M&L cement concrete with PCC type D2 1:4:8 using 40mm graded aggregate as in foundation.

M&L for M25 RCC design mix using 20 mm graded aggregate for raft foundation footing ,bases of columns, plinth beams & mass concrete.

M&L for M25 RCC design mix using 20 mm graded aggregate for columns, pillars,posts and struts.

M&L for M25 RCC design mix using 20 mm graded aggregate for beams, cantilevers, lintels over 1.5 m span.

M&L for M25 RCC design mix using 20 mm graded in slabs supported on walls and the like complete all as specified and directed.

M & L for TMT reinforcement 10 mm dia and over cut to length bent to shape including cranking, hooking etc binding with mild steel wire not less than 0.90 mm dia (annealed) all as directed complete.

S & F mild steel TMT bar 5 mm dia and over upto and including 10mm dia in strrups as in including cutting, bending and binding with mild steel not less than 0.9 mm dia (annealed) all as directed complete.

Form work for foundation footing , bases of columns &plinth beams similar work vertical or batter.

Form work for side of pillars, posts, columns & similar works vertical or batter.

Form work to side & soffits of floor or roof beams lintels & similar works.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floors slabs, landings and similar work, not exceeding 200mm thick for fair finished surfaces complete all as specified and directed.

M&L for Pre-cast RCC 1:2:4 type B1 using 20mm graded stone aggregate as in landing, cover slabs (for manhole covers, drains etc) set in CM 1:6 complete all as specified.

M&L for brick work with burnt old size bricks built in cement mortar 1:6 straight or curved on plan exceeding 6mtr mean radius and all as directed.

M&L for brick work with burnt old size bricks built in cement mortar 1:4 straight or curved on plan to any radius in half brick thick walls and all as directed.

M&L40 mm thick Damp proof course to horizontal or vertical surfaces including necessary form work in cement concrete 1:2:4 type B-0 (Using 12.5 mm graded stone aggregate) mixed with WPC ( WPC shall be measured & paid separately

M&L rendering 15mm thick on other than fair faces of brick or concrete Surfaces in cement mortar 1:6 finished even and smooth.

M&L for 15mm thick plaster on fair faces of brick work or concrete surface in cm (1:4) with wpc @2% by weight face of conc work to wall surface and the surface is finished even and smooth without using extra cement

Supply only integral WPC

M&L for 5 mm thick rendering on Celling plaster of concrete surfaces in cement mortar 1:3 complete all as specified and directed

M&L for 75 mm thick PCC 1:3:6 type C2 using 40mm graded aggregate as in plinth course as directed by engineer in charge.

M&L Sand filling under floors or in foundations including watering and conosoldiation.

M&L for broken stone or boulders of hardcore of gauge n exc 63 mm deposited, spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface.

M&L for 100mm thick PCC type D2 1:4:8 using (40mm gradded aggregate) as in sub base.

M&L for Pre-polished Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigment in floors including screed bed 15 mm thick in CM 1:4 complete all as specified and as directed.

M&L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc.set and jointed in neat cement slurry and pointed in white or coloured including Screed bed or bedding layer of cement mortar 1:6, 15 mm thick for laying floor finishes.

M&L for Glazed ceramic coloured tiles in vertical surfaces 600 x 350 x 7 mm thick set and jointed in neat cement slurry & painted in white or colour cement to match incl 10 mm thick backing coat in CM 1:4 .

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rainforced with MS square tube in opening as per specification & as directed.

S&F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. .frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail,; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification complete all as specified and as directed.

S&F powder coated aluminium frame for doors, windows, ventileters with one or more rebates including joining cleat for fixing etc complete all as specified in cl power coating above aluminium section.(minimum thickness of poweder coating 50 micron).

S&F 4 mm thick Sheet glass is frosted on one side , ordinary quality and glazing with aluminium beads in squares exceeding 0.50 Sqm in each pane

S&F 150mm long aluminium anodised barrel tower bolts of extruded section

S&F 100mm size MS butt hinges medium weight

S&F 150mm size aluminium handle cast type anodised

S&F 15mm bore GI tubing medium graded with all fitting and fixed complete to wall and ceiling or laid in floor .

All as per item No 38 here in before but 20mm dia

S&F 20 mm Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed

S&F 15mm bore bib tap cast copper alloy fancy type chromium plate with crutch or butter fly handle screwed down for iron pipe but fancy type.

S&F 15mm bore stop cock/valve cast copper alloy screwed down high pressure with crutch or butter fly handle screwed both end for iron pipe complete.

S&F PVC connector 600mm long with brass coupling in both ends screwed down for iron pipe.

S&F 15mm bore pillar tap fancy type cast copper alloy with capstin head CP screwed down high pressure with or without littered 'H' or 'C' with long screwed shank and fly nuts screwed for iron pipe etc complete.

S&F vitreous china wash basin white, flat back, size 550x400mm excluding taps , waste ,but including barkets.

S&F 32mm bore dia Waste coupling of PTMT (half or full threaded) minium weight 45 gms)

S&F 10 litre capacity PVC type low level flushing cistern with inlet ball valve, float and handle/push flush type brackets etc complete .

S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe)

S &F Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe)

S &F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F stainless steel Soap dish approximate size 160x 160x90mm , any type, fixed to wall with chromium plated brass screws

S&F brass chromium plated towel rail, 20mm dia, D type, 60cm long between flanges

S&F 100mm dia PTMT grating.

S&F 75 mm thick PVC (SWR pipes single socketed in any length with rubber ring joints laid in trenches or floors.

S & F 75 mm bore PVC (SWR) bends of any radius.

M&L 75 mm bore pvc floor trap, plain with grating including jointing with solvent

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes double socketed in any length with rubber ring joints fixed in walls.

S & F 110 mm bore PVC (SWR) bends of any radius.

Supplying, laying and testing of 150 mm internal dia of double wall corrugaed (DWC) high density polythylene pipe (HDPE) and stiffness classes 8 (SN-8) with ISI marked (With CML No ) with and including all fittings & jointing materials for connection of inspection chamber/WC to first manhole of the sewage line complete all as specified and directed..

Cutting into existing manholes of 150 mm dia for connecting new drains making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching as required.

S&F 500 litres Rotational moulded polythylene water stroage tanks (cylindrical vertical with closed top) hoisted & fixed in position all position all as specified in SSR part -I incl all necessary fittings.

S&F 20 mm dia ball valves, PTMT high pressure of epoxy coated Aluminium rod and high density plastic ball (200 gms) complete, screwed for iron pipes or brasas ferrule and fixed.

M & L for preparation of new plastered surface and applying three coats of white wash on Walls/Ceiling all as specified and directed

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out in soft loose soil complete all as specified and directed.

M&L for 100mm thick PCC type C2 1:3:6 using (40mm gradded aggregate) as in sub base/Hardstanding.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand

M & L for PCC 1:2:4 type B-1 using 20mm graded aggreagte as in haunching,benching,coping etc complete all as specified and directed

Excavating in post holes (or similar holes) each n exc 0.5 cum,in soft/loose soil and getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed.

M&L cement concrete with PCC type B2 1:2:4 using 40mm graded aggregate as in foundation.

S&F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specified.

M&l Painting two coats of synthetic enamel paint over a coat of red oxide primer to new steel Surfaces of any description, not otherwise described, over 10cm width or girth.

M&L PCC 1:3:6 type C-2 (using 40mm graded stone aggregate as in foundation filling / mass concrete,complete all as specified and directed.

S & FPre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M & L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment including 50mm thick sand cushion all as specified and as directed

M&L for preparation of new plastered surfaces of walls and applying two coats of acrylic distemper including one coat of chalk whiting on plastered surface to prepara-tory to distempering complete all as specified and directed over 1 mm thick wall care putty complete as directed.

M&L for preparation of new wall surface applying Two or more coats of 100% Premium acrylic exterior emulsion paint with silicone additives of required shade additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @2.20 litre/ 10 sqm complete as directed. ( Note: WPC shall be measured and paid seperately)

M&L Rendering 5 mm thick on fair faces of concrete surfaces with 1:3 CM on ceiling surfaces etc., finishing the surfaces even & smooth w/o using extra cement incl Prepration of new plastered surfaces on ceiling over applying three coats of white washing complete all as directed

M&L for Spreading and levelling in layers n exc. 25 cm thick and watering and well ramming under floor complete all as specified and directed.

M&L 75 mm thick Cement concrete 1:4:8 type D-2 (using 40 mm graded agg) as in sub base complete all as specified and directed.

Material and labour for premium quality, non skid coloured ceramic tiles, 600 x 600 x 7 to 8 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including cement screed bed 15mm thick in cement mortar (1:6) base complete all as specified and directed.

Material and labour for premium quality, non skid coloured ceramic tiles, 600 x 600 x 7 to 8 mm thick as in skirting, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including cement plaster 10mm thick in cement mortar (1:4) complete all as specified and directed.

Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified incl power coating above aluminium section.(minimum thickness of poweder coating 50 micron).

Supply and fix anodised aluminium three track sliding window and ventilator frame side/top/shutters (weight of section not less that 0.55 Kg/RM) aluminium section without sash bar aluminium section including all necessary joining cleats,hold fast, rubber gasket anodised snap beading, anodised aluminium fittings, suitable alum handle and locking arrangement etc, two track for glass and one track for aluminium wire mess etc, including powder coated of any colour (thick of power coating not less than 50 micron) & providing AC hole complete all as specified and directed.. Note:- (i) Wire cloth /glass shall be measured and paid separately at SUPPLY only rates under appropiate items. (ii) Labour charges for fixing of wire cloth/glass panes is demeed to be included in unit the unit rate quoted.

S & F 5.5 mm thick frosted glass, ordinary quality and glazing with wooden beads in squares not exceeding 0.5 Sq. M in each pane

S & F 4 mm thick Sheet glass, ordinary quality and glazing with wooden beads in squares not exceeding 0.5 Sq. M in each pane

S&F Galvanised MS wire cloth 0.46mm nominal dia of wire and average width of aperture 1.18mm, complete and as specified.

S&F MS framed work such as grills, gratings, etc with ends of bars shouldered and/or revited, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work confirming to Fe.290. Gde-E-165

M&L for roof treatment with the following specification - applying water proofing treatment on horizontal or vertical surfaces by applying oil bound bitumen primer @ 0.20 Kg/sqm and providing 3mm thick APP modified water proofing membrane weighing not less than 3 Kg/sqm reinforced with non-woven polyester matt weighing not less than 160 gm/sqm, The overlap shall be minimum 100mm on transverse direction and 75 mm on longitudinal direction and sealing overlap by torch application and bonded and applying a coat of blown grade hot bitumen 85/25 over and below the membrane @ 1.20 Kg/sqm in drying over the membrane finished with solar reflective bituminous aluminium paint/ primer @ 0.10 Kg/sqm over RCC roof slab/ parapet after cleaning the surfaces by removing dust, dirt etc. as per manufacturer’s instructions and all as specified and as directed. NOTE :- The work shall be executed at site by the authorised applicator of APP and as approved by the GE.

S&F for Anodised aluminium/ GI snap grid power coated framed work of size main runner 39x24.70x0.80 mm, cross tee size 29.x24.70x0.80 mm, wall angle 22.2x22.2x0.65 mm and size of grid 605x605 mm for false ceiling all as specified with 4mm thick GI suspender complete all as specified and as directed.

M & L for 4mm thick Non Asbestos designed Cement E board of size fixed in ceiling as flat or slope complete as specified and directed.

S&F Steel work Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etccomplete all as specified and as directed.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing confirming to FE 410,E-250 Quality A complete all as specified and directed.

M& L for Granite of any type 20 mm thick cut beded and jointed with grey cement slurry and pointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete in vertical surfaces of wall incl 15 mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, et

M&L Brushing neat cement slurry with 3.0kg of cement per sq. metre

M&L Cement concrete type B-1, 1:2:4 (12.50mm graded aggregate)

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 . (Internal water proof compound measured seperately)

M&L for MS work for fencing post and struts made from angle iron and flat iron in any section including cutting tops to shape , drilling holes and notching for fixing of wires etc confirming to Fe -290 or Fe -330, with and incl necessary nut and bolts of 12mm dia of reqd length complete.

Supply only chain link MS galvanised any mesh size or type complete all as specified.

Fixing only chain link fencing including line wire, any mesh, size and any type of standards rails straining bolt etc including provision of binding wire complete all as specified and directed.

S&F mild 12 mm steel screw bolts with hexagonal or square heads at one end and screwed the other and screwed end to be fitted with washers, one nut not exc 15cm long and dia of neck exc 12mm & n.exc 20mm

S&F roof trusses (framed) trussed, purlins, crane gantries, gate, grill, rails and fastenings and heavy bracket framing (beam tee, angle, channel or flat sections) including clits etc conforming to Fe-410-0 W Gde- E- 250, Quality -A.

S & Fix Galvanised 2 strand, steel barbed wire, 2.24mm dia barbed with 2mm dia barbs straining and fixing to any type of standard rails straining bolts, includigng, securing or tying at crossings with and provision of steel wire, staples or steel pins, etc complete.

M&L for hardcore of guage exc 63mm but n exc. 100 mm, deposited,spread and levelled in layers n exc. 15 cm thick of broken stone or boulders, watered and rolled to true surface complete

M&L PCC 1:3:6 type C-2 (using 40mm graded stone aggregate as in foundation filling / mass concrete,complete all as specified and directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, and including nut bolt and MS plate etc, complete all as specified and as directed.

M&L for providing precast cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) set in cement mortar 1:4 in kerb stone with plain fair faces complete all specified and directed

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and pigment including 50mm thick sand cusion complete all as specified and directed

M&L for 100 mm thick cement concrete type B-2 (1:2:4) using 20 mm graded stone aggregate as in path/hardstanding/sub base including Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed. complete all as specified

Material and labour for point wiring with 1.5 sqmm (nominal area) FRLSH PVC insulated stranded copper conductor single core including PVC conduit of appropriate size concealed in wall, pressed steel concealed terminal boxes of required size and with top cover 3 mm thick of plastic laminated sheet of reqd colour, painting terminal boxes inside and out side with one coat red oxide primer complete with all accessories and all as specified including 1.5 Sqmm FRLSH PVC insulated unsheathed multistranded copper earth conductor to common earth and connected to earth dolly for fan / light / exhaust fan/ bell point controlled by one switch. Note:- 1. Cost of PVC conduit, steel terminal boxes, plastic laminated sheet cover etc; are deemed to be included in the quoted rate. 2. Cutting chases on walls / ceiling and making good disturbed surfaces including finishing with cement mortar (1:3)and ,putty and plastic paint matching with existing surface etc; shall be deemed to be included in the rate quoted above. : (a) One light point controlled by one, one way switch 5 Amps

(b) One 3 point 5 Amps socket outlets point controlled by one switch on the same board

(c) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board

All as per item No 126 above but with two run of 2.5 sqmm multi stranded Single core copper conductor 1100 volts grade FRLSH PVC insulated sheathed cable with one run of FRLSH PVC 2.5 Sqmm multi standard insulated sheathed copper wire as earth continuity conductor along with wiring and connecting to the common earth dolly on independent board.

S & F Switch piano (White) flush type single pole one way 5 Amp, 230 Volts complete all as specified.

S & F Socket outlet (White) 2 in 1,5/6 pin, 5 Amps complete all as specified and directed.

S & F Switch socket combination (White) flush type multipurpose 5/6 pin 5 Amps two in one , 230 volts complete all as specified .

S&F Switch socket combination (White) 2 in 1 5/6 pin, 15 Amp flush type universal.

S&F ceilling rose (White) three terminal surface bakelite type AC 50 Hz 230 Volt of size 65x50mm complete all specified .

S & F ceiling fan regulator (White) step type, flush type heavy duty suitable to work on 230 Volt AC supply complete all as specified.

S & F Lamp holder (White) with insulated body, with back plate suitable for batten fittings complete all as directed.

S & F LED ADORE 10 W B22 CDL 5 STAR LAMP with B 22 base capacity 1200 lumen complete all as specified.Make-Make- Havells, Cat No: LHLDEUEBML8Z010 or equivalent in Crompton /Philips / Surya.

S & F sheet metal enclosure MCB DB TPN 4 way with 200 amps rated bus bar 415 volts double door with magnetic locking system complete including grouted on walls all as specified

S & F MCB TPN 415 volts suitable for fixing in MCB DB of capacity 63 amps complete all as specified and directed.

S & F MCB TPN 415 volts suitable for fixing in MCB DB of capacity 40 amps complete all as specified and directed.

S & F sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system complete all as specified. Make-L&T/ Schneider/ Legrand / Seimens

S & F MCB Double Pole 32 Amps 240/415 Volt, confirms to IS/IEC 60898 Breaking Capacity of 10 kA, B-curve, complete all as specified and directed.Make-L&T/ Schneider/ Legrand / Seimens

S & F MCB SP, 240 volts, 6-32A Amps 50 Hz ,confirms to IS/IEC 60898 Breaking Capacity of 10 kA, B-curve, complete all as specified and directed. Make-L&T/ Schneider/ Legrand / Seimens

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative ultra slim round profile LED lighting fixture with extruded polycarbonate , environmental friendly energy efficiebt ready to use pack with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make :- Havells/ Crompton / Philips/ Surya

S & F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and PC Cover having TOP opening seperate driver compartment with IP 66 Protection and impact resistance of IK07 with electronic driver of capacity 20 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade 32 mm dia 1.5 mtr long bend to required shape complete all as directed by Engineer-in-Charge. Make- Havells /Crompton / Philips/Surya

Supply and fixing ceiling fans without remote complete with blades, down rods, , fan hook and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed. Make Havells/Crompton/Usha

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 380m sweep with, blades, and frame and louvers , making suitable size hole as per size of exhaust fan duly finish as per existing surface complete all as specified and directed .

M & L Submain wiring with 4 runs of single core 6 sqmm PVC insulated FRLSH unsheated multistranded 1100 volts grade with copper conductor drawn through and including non-metalic rigid PVC concealled conduit ISI marked and its accessories including one run of single core 6 sqmm PVC insulated FRLSH unsheated multistranded 1100 volts grade with copper conductor cable as earth continuty conductor along with the wiring and connected from DB to DB/main board complete all as specified and directed.

M & L Submain wiring with 2 runs of single core 6 sqmm PVC insulated unsheated (FRLSH) multistranded 1100 volts grade with copper conductor duly cutting chases on walls and drawn through and including non-metalic Rigid PVC Conduit ISI marked and its accessories including one run of single core 6.0 sqmm PVC insulated unsheated multistranded 1100 volts grade with copper conductor cable as earth continuty conductor along with the wiring and connected from DB to DB/main board with proper copper lugs and making good disturbed surfaces and matching with existing colour complete all as specified and directed.

S & F sheet metal enclosure MCB DB SPN 4 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system complete all as specified. Make-L&T/ Schneider/ Legrand / Seimens

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed .

M&L Point Wiring with 1.5 Sqmm Copper Conductor single core PVC insulated Flame Retardant Low Smoke (FRLSH) Unsheathed 1100 Volt grade multi-stranded Cable drawn through and including PVC Casing and Caping medium grade of suitable size and its Accessories as required at Site, fixing on surface of Wall, Roof, mounted on Sunk Mild Steel Pressed Terminal Box 1.22mm thick of suitable size duly painted with red oxide metal primer with 3.0mm thick Plastic Laminated Sheet Top Cover for mounting Switches, Sockets, etc. including PVC insulated and unsheathed Single Core multi-stranded Copper Conductor Cable of size 1.5 Sqmm (FRLSH) Green in Colour as Earth Continuity Conductor connected to Common Earth and Earth dolly for One Light/Fan/Bell Point controlled by One 1-Way Switch 5 Amp, duly fixed with copper lugs and flexible pipe from ceiling rose to fitting/fixtures complete all as specified and as directed.

Description all as per item No 150 here in before but One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board

S&F pre-wired double door MCB DB made out of 18 SWG CRCA steel sheets, Phosphates powder coated with copper bus bar, Earth stud, Din Rail, Polyamide Terminal Blocks for incoming and outgoing circuits, inbuilt loose wire box, Ground terminal blocks, duly pre-wired with thimble flame retardant copper conductors and poly layer for protection SP 240 volts 200 Amps rated bus bar, 4 way double door open able complete.

Excavation in trenches n exc 1.50 m wide and n exc 1.50 m depth in soft /loose soil and getting out for lying of cable and errection pipe etc complete all as directed.

Returning, filling in, trenches in soft /loose soil including spreading, leveling, watering and well ramming in layers not exc 25 cm complete all as directed.

Removal of excavated soil to a distance n. exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as directed.

M & L sand cushioning in trenches for cable protection with coarse sand laid dry in trenches with uniform thickness including consolidation complete all as directed.

Supply & Laying well burnt brick , locally available best quality (sub class "B" bricks ) laid in trences perpendicular to UG Cable protection complete all as specified.

Supply & Laying XLPE LT heavy duty UG Cable of size 25 Sqmm 3.5 Core laid in trences /floor/on wall/service connection PVC Insulated, sheathing and armd 1100 Volts grade with aluminium conductor including connection to the main switch/cut out MCB/MCCB with necessary lugs after cutting to required length complete all as specified and directed.

S & F GI Tubing light grade of size 40mm dia in protection of cable at road crossing /hard standing/pole protection fixed with clamp as per site requirement etc all as specified and directed.

Boring holes horizontally under Road without damaging the surface of Road of any type (minimum 1.0 METRE below the Road Surface with the help of GI Tubing not exc. 40mm bore (dia) for passing of UG Cable, complete all as specified and as directed. NOTE: GI Pipe laid will be measured and paid separately under appropriate Item.

Material and labour for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground to a depth not less than 2.25 mtrs below ground level with top edge of earth plate not less than 1.5 mtrs below normal ground level connected to GI earth wire 4 mm dia connected to main earthing lead from earth electrode to test point upto 7.5 metre drawn through and including GI protection pipe of light grade 15 mm bore by means of bolts, nuts, check nuts and washers including excavation earth work provisioning of PCC chamber made of PCC 1:3:6 RCC cover funnel with wiremesh 20mm dia watering pipe Medium grade, GI protection pipe 20mm dia bore all as specified in Electrical Plate No.3 of SSR Part I.

Supply & Laying XLPE LT heavy duty UG Cable of size 10 Sqmm 2 Core laid in trences /floor/on wall/service connection PVC Insulated, sheathing and armd 1100 Volts grade with aluminium conductor including connection to the main switch/cut out MCB/MCCB with necessary lugs after cutting to required length complete all as specified and directed. Make :- Polycab / Havells / RR Kabel / Gloster

S&F in repairs 3 layered (Outer Green Coloured UV Stabalized, Middle Black Coloured UV Stabalized and Inner Most Layer White Coloured with Antimicrobial Property) PP-R (Polypropyelene Random Copolymer) Pipe 50 mm Outer dia, ISI marked, SDR 7.4, PN 16 and Antimicrobial Fusion Welded having Thermal Stabality for Hot and Cold Water Supply all PP-R Plain and Brass Threaded Polypropyelene Random Fittings and laid in Trenches, complete all as specified and as directed.

S&F in repairs 3 layered (Outer Green Coloured UV Stabalized, Middle Black Coloured UV Stabalized and Inner Most Layer White Coloured with Antimicrobial Property) PP-R (Polypropyelene Random Copolymer) Pipe 32mm Outer dia, ISI marked, SDR 7.4 , PN 16 and Antimicrobial Fusion Welded having Thermal Stabality for Hot and Cold Water Supply all PP-R Plain and Brass Threaded Polypropyelene Random Fittings and laid in Trenches, complete all as specified and as directed.

S&F in repairs PP-R Gate Valves (Brass Insert) 32mm Outer dia and fixed including taking down of existing unserviceable One, complete all specified and as directed.

S&F in repairs PP-R Gate Valves (Brass Insert) 50 mm Outer dia and fixed including taking down of existing unserviceable One, complete all specified and as directed.

Making connection of PP-R distribution branch with PP-R main of 63 mm size by providing and fixing tee of 63 mm x 50 mm including cutting and making fusion joint etc all as specified and directed.

S M STORE (BID ID -3386886)

M/s DEBAJIT BORTHAKUR (BID ID -3386814)

M/S L R ENTERPRISE (BID ID -3386933)

M/S RANA ENGINEERING ENTERPRISE (BID ID -3379022)

SNEH CORPORATION (BID ID -3379573)